Search Documents

WaihiÆs Cornish Pumphouse is located on the edge of town in a dynamic and changeable area where history affects the future. As in any successful project, ingenuity and team work have been significant factors in the planning and implementation of the buildingÆs relocation.   Work around the Pumphouse site commenced circa 1900 with preparation to sink the No 5 shaft. Construction of the pumphouse and the steam driven C pump was completed by 1904 with hints of what was to come evident in 1905 as the No5 Shaft collar had sunk 350mm in four years. By 1907 surface cracking developed over the Milking Cow cave area and in 1913 200 mm was cut off the main pumping rod as the ground was sinking at a rate of 25 mm per year.   In 1913 ground around No 6 shaft had subsided 600 mm.It was also the end of an era as steam gave way to hydroelectricity and electric pumps replaced the C Pump. C Pump was maintained as a backup from 1913 to 1929 and then finally scrapped. 25 years of underground caving operations removed approximately 400 000 cubic metres of ore leaving a 7 ha collapse crater that eventually became known as the mine lake.   On the edge of town a tension zone over the Royal Lode began to develop 50 m diameter chimney collapses as large scale blocks relaxed into unfilled stopes in the old Martha underground mine. After the 1999 collapse part of the main street was closed and after the 2001 collapse Hazard Zones were declared, more streets closed and areas evacuated and retired from residential use.   By 1984 the Pumphouse has approximately one degree of tilt and in 2002 tilt on the Pumphouse accelerated briefly and then settled down. Tilt accelerated again late in 2004 and a scoping study was initiated to define protection options for the pumphouse. The Martha Mining Licence requires Newmont to 'Take whatever precautions are necessary to protect the old Cornish Pumphouse adjacent to No5 shaft' and viable solutions needed to found.   Any work on the Pumphouse comes standard with a wide range of stakeholders, governing agencies and legal framework to consider. Land Information New Zealand (LINZ) is owner and administrator of the pumphouse.

Jan 1, 2006

By Johnston R. F

The factors which influence the reduction of chromite are investigated with special reference to Coobina chromite. This was compared with a South African chromite ore. The reduction characteristics are outlined and the reduction kinetics studied Temperature has the most significant effect, followed by particle size, silica addition and type of coal.Electron microprobe analysis of the products indicates that iron in the chromite is first reduced at temperatures above 1100°C, followed by chromium at around 1200°C. At temperatures greater than 1200°C metallic iron and chromium are formed simultaneously and subsequently give an iron-chromium-carbon alloy. It was observed that the metallic carbide contains a small amount of silicon. The decomposition of the chromite spinel was observed to pass through the FeO.Cr2O3, MgO.Cr2O3 and MgO.AI2O3 forms before slag formation. It is concluded that Coobina chromite is suitable for the production of ferrochrome if direct prereduction followed by intensive bath smelting is used.

Jan 1, 1994

By S Bright, M J. Masamvu, E K. Chiwandika, S Dandi, S M. Masuka

The depletion of high-grade hard and lumpy chrome ores has forced Zimbabwean ferrochrome producers to resort to low-grade friable ores that have an average of 28 per cent fines against a set limit of 12 per cent. Submerged open arc furnaces currently in use are associated with eruptions within the furnace because of the high amounts of fines, high energy consumption, as well as high SO2 and CO2 emissions. Traditionally employed agglomeration methods such as pelletising and the use of coke in the furnace have been discarded because of the pressure to lower operational costs and to achieve higher profit margins. This research aims to develop a method to incorporate lowgrade friable ore fines and unprocessed coal into production while lowering CO2 and SO2 emissions through a closed direct current (DC) arc furnace. The closed DC arc furnace could incorporate the friable ores and coal while maintaining above 90 per cent reduction rates. Preliminary findings also show that energy consumption could be reduced by up to 35 per cent by incorporating a pre-heating and pre-reduction system using the flue gases from the furnace. In the proposed circuit, the cost of production per ton of ferrochrome might be potentially lowered by an average of 30 per cent.

Jun 19, 2024

By Blair J. R

A Train Performance Calculator (TPC) is an essential tool in railway operations, as a means of acquiring quickly a precise measure of the performance of the system. Traditionally the TPC was used in the form of program for a large computer. By employing an efficient integration algorithm and tailoring the program to suit the computer system it is shown that it is possible to devise a TPC for a mini computer. The resulting low running costs and flexibility of operation makes this a useful design tool. This TPC was developed to study problems associated with a single track railway operation. It was applied specifically to study the railway operated by the Mt. Newman Mining Co. Limited in the Pilbara region of W.A. to transport iron ore from the mine to the port. The TPC was used to calculate the effects of changes to locomotive power, to train size, to the track and to the amount of traffic. Its accuracy was checked by comparing its performance with that of the actual trains.

Jan 1, 1977

The primary object of this paper is to describe the present metallurgical practice of the Emperor Combined Mill, wherein ores from the adjoining and Associated Mining Companies, Emperor Gold Mining Company Ltd., Loloma (Fiji) Gold Mines, N.L., and Dolphin Mines, Ltd., are treated for the recovery of gold and silver.The mining field is located in the foothills, five miles from the sea, on the northern side of Viti Levu, the largest and most important island of the Fiji group.The orebodies occur in basalt and associated ash beds overlain by andesite, tuffs and sediments. The basalt is a dark greenish-black rock and in much of the ore mined is weathered with alteration of the olivine to serpentine and iron oxides, of the augite to chlorite and of the minute included crystals of iron ore to other iron oxides. Into the basalt intrudes a considerable number of andesite dykes, and the lodes occur as veins in these dykes, as "flatmakes" along fissures or, ash beds extending horizontally from the dykes and at the contact of the basalt and the andesite dices.The Emperor orebody is the largest and most important, and consists essentially of massive, shattered, well altered and mineralized basalt.Little or no free gold occurs in the ore at present being milled, the most important host minerals for gold being the tellurides sylvanite and hessite, next in importance being the sulphides, pyrite, marcasite and arsenopyrite. Chalcopyrite is present in quantities large enough to be troublesome in the subsequent concentrate treatment section, while sphalerite, tetrahedrite, bornite, galena and native tellurium are present in small quantities.Unimportant occurrences of native copper have been observed in both Dolphin and Emperor orebodies.

Jan 1, 1953

By Jackson D. G

Iron ore mineralisation in the Paraburdoo environs is known to extend almost continuously over a strike length of 55 kilometres. Six formations of the Mount Bruce Supergroup con- tain high grade mineralisation in varying degrees of importance. Ore is currently being mined from the Joffre and Dales Gorge Members of the Brockman Iron Formation, with smaller, less significant amounts, occasionally taken from the lowermost units of the Weeli Wolli Formation and the upper parts of the Mount McRae Shale. Regional mapping has demonstrated the existance locally of a major unconformity at the base of the Wyloo Group sediments out- cropping south of the minesite. The basal con- glomerates at the unconformity are sometimes mineralised at Paraburdoo. A supergene enrich- ment process controlled by structure, strati- graphy and topography is the only one which can satisfactorily explain the disposition and chemistry of the Paraburdoo iron orebodies.

Jan 1, 1979

By M I. Roberts

Corporate and workplace culture, as many owners, directors, executives and managers know, is by far the most powerful determinant of productivity. It’s much more significant than buildings and equipment. Yet although no one today would build a building or machine without a plan, few leaders have a plan for building and sustaining a safer and more productive culture.Using practical ways, culture can be planned and shaped as desired. Success requires implementing a project plan for changing the systems that drive behaviours that in turn shape attitudes. The combination of behaviour and attitude together with leadership largely shape culture.To improve performance, leaders need to:1. improve the organisational systems that drive behaviour2. action a project plan for improving specific performance metrics 3. demonstrate leadership that is conscious, disciplined, committed and passionate for purposeful use of human energy.This paper explains all three factors in practical ways with operational and corporate examples. It details understanding and applying the power of fundamental statistical analysis tools to recalibrate, focus and drive proactive leadership that takes responsibility for process improvement, supporting people and ensuring accountability.Experience and practical understanding of human and organisational behaviour confirm that the Measurement ? Analysis ? Reporting system combined with conscious leadership is by far the most powerful driver of behaviour. This wisdom produces profound changes in leadership style and behaviour. It develops outstanding leadership to create and sustain a safe and highly productive culture reliably producing consistently high quality products. It is the key to developing accountability, employee retention and a sustained competitive advantage.CITATION:Roberts, M I, 2016. Building safe, productive cultures and leadership, in Proceedings International Mine Management Conference, pp 163-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Rongqing Q, Tiancong Z, Yiyuan L

The influence of pulp density, ferric ion concentration and particle size on the tank bioleaching of two kinds of refractory gold concentrates are discussed. The chemistry and mechanism of the bioleaching process are also presented. The relationship between oxidation of sulphides, liberation of enclosed gold and gold cyanidation are discussed. The consumption of NaCN could be reduced by alkaline treatment of bioleached residues prior to Cyanidation.

Jan 1, 1992

By Ross J. F

A pillar 'is a block of coal left in the first working of a coal seam for the purpose of supporting the superincumbent strata in such a manner that the winning out roadways will be safe to traverse by men and by the coal transport system.PRINCIPLES OF PILLAR EXTRACTION.The size of a pillar is chiefly dependent on the depth of cover, and in a lesser degree on the nature of the coal, or the condition in which the seam has been laid down. In a seam at 1,100ft. depth of cover, and assuming a spec'ific gravity of 2.5 overall for the cover strata, a pressure of 1,200lb. per sq. in. is the loading on the top surface of the coal seam before mining begins.When mining commences, and as the pillars are formed, an increased load is imposed on the coal left in the pillars, according to the percentage of coal extracted in the first working. Thus, if 25% extraction is taken in the first working, the load on the pillars is theoretically increased from 1,200lb. per sq. in. to 1,600lb. per sq. in. over the area mined. If this state of things went on indefinitely it would not be possible wholly to extract a pillar because of the extreme pressure tliat would be thrown on the diminishing portion; but, fortunately, another element, that of time, enters into and assists the process of extraction.If the superimposed strata were of an entirely plastic nature, this time factor could not operate, as the cover weight would settle instantly on the remaining portion of the p'illar and finally overwhelm it. The cover strata above a pillar generally have a certain rigidity which does not allow the superimposed weight to settle instantly on the pillar fraction, and it requires a period of time to elapse before the extra weight is felt by the pillar.The time factor varies widely, and is governed entirely by local conditions; it can only be determined by experience gained on the spot or in close proximity to the area of operations. It is dependent on the strength of the strata and its characteristics under bridging conditions.It is, therefore, logical to assume that the more rapidly a pillar can be extracted the greater will be the safety factor and also the percentage of recovery of coal.Up to the present time, the operation of the extraction of pillars in this country has been, with a few exceptions, a manual one, and before mechanization of Collieries can be fully accomplished, the process will have to be performed mecharrically.

Jan 1, 1947

In 1556, Agricola noted that "a prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him"(1). In today's world, the owner rarely has the opportunity to visit the mine and, instead of reading about the `nature of the vein' in annual reports, prospectuses, government publications, et cetera he sees the words `reserves' and `resources'. Unfortunately, the subject of reserves and resources has become increasingly complex and Canadians, along with their counterparts in Australia and elsewhere, are still struggling with definitions which will attempt to cover all conceivable circumstances from national or regional resource endowment to the material to be extracted next week from a given stope or open pit bench. The providers and recipients of reserve and resource data are: - Government agencies who are concerned with questions of national endowment, strategic use of raw materials and other questions of public policy. - Stockholders who have a vested interest in the basic assets of their companies. - Financiers who are concerned about the security of their loans. - Regulatory bodies whose function is to protect a frequently naive investor from unscrupulous practices. - Management, at head office and on-site, who need basic information for decision-making, whether it be to open up a new mine, expand or close an existing operation, acquire or merge with other entities, or, more mundanely, for routine mine planning. To satisfy their demands with unanimously accepted definitions is a formidable task but, it is my impression that, little by little, a concensus appears to be growing within the industry.

Jan 1, 1987

In Munich's peculiar hydrogeological conditions (water bearing sand strata between layers of impermeable clay, silt or marl) are proper functioning groundwater lowering methods of decisive importance for underground construc- tion. Shield tunnelling with compressed air has al- ready proved to be successful. In view of growing application of shotcrete tunnelling it was obvious to consider the use of compressed air even here. After a preliminary research-project the first subway section "shotcrete under compressed air" was 1979 awarded in Munich and since that time five sections have been awarded, respectively completed. On the basis of the experiences meanwhile obtained reports will be given stating the frame conditions in which this new construction method can be applied. The tunnels consist of two shells. The outer ist driven by shotcrete under compressed air. In order to keep the air overpressure low, the groundwater often is previously detensioned or partially lowered. The inner shell of watertight concrete is built under atmosperic pressure.

Jan 1, 1987

By E Jak, M Shevchenko, D Shishin

One of the key aspects to develop sustainable metallurgical production is to ensure that the predictive power of thermodynamic tools is brought up to a new level of accuracy and reliability. Exploring new polymetallic processes, integrating primary and recycled materials, means utilising the uncharted areas within the Cu-Pb-Zn-Fe-Ca-Al-Mg-Si-O (major) – Cr-Na (slagging) – As-Sn-Sb- Bi-Ag-Au-Ni-Co (minor) slag-solids-metal-matte-speiss-sulfate system. This requires extensive integrated experimental and thermodynamic modelling study, which is underway at PyroSearch at the University of Queensland (UQ).

Aug 21, 2024

With the use of 36 rock drills of the jackhammer type at the West Lyell Open Cuts of the Mt Lyell Mining & Railway Co, it is of importance to determine the economic as well as the physical life of these machines. With this purpose in mind records have been kept of the footage bored and the cost of new parts placed in each machine, and the following procedure adopted.A graph is plotted for each machine showing the footage bored as a horizontal line and at each 5000 feet of boring the total cost of new parts is noted on this line (see Figure 1). Thus at a glance it is possible to see the amount of work done by each machine and the money spent on it in new parts. However, it is difficult to visualise from this graph the increase in the cost of new parts for each machine as its life advances. To obviate this clifficulty a curve is plotted with the cost of new parts as the vertical component and the distance bored as the horizontal component.As before the cost of new parts are taken at each 5000 feet bored (see Figure 2).

Jan 1, 1994

By Y K. Leong

Iron ore tailings typically containing 40 to 50 per cent Fe can be beneficiated to iron ore products containing 54 to 60 per cent Fe. The impurities are comprised of clay, quartz, cristabolite and TiO2. Goethite and hematite are also present. At high concentrations of 55–60 wt% solids, the tailings displayed high yield stress and viscosity and cannot be pumped over long distances. Composite additives comprising of NaOH, phosphate-based additives and sodium metasilicate are found to reduce the viscosity and yield stress very significantly by a few orders of magnitude. The yield stress of 100 Pa can be reduced to almost zero. At this state, dilution of the tailings with its process water to 40 per cent solids causes the coarse and high-density iron ore particles to separate from the colloidal fractions located in the supernatant after a few minutes of sedimentation. Separation by decantation produces a sediment with an Fe content of 54 per cent from tailings with 47 per cent Fe. Another tailings sample with 48 per cent Fe was beneficiated to greater than 57 per cent Fe using NaOH-metasilicate-polyphosphate additives and employing an additional washing step. The use of other composite additives, NaOH and polyphosphates, increased beneficiated product Fe content to greater than 60 per cent from the same tailings. With the current iron ore spot price of more than US$180 per tonne, the cost of this treatment process even including a desalination step, if necessary, is relatively insignificant. This study has given tailings an economic value that should be exploited as soon as possible.

Nov 8, 2021

By E Kasai, D Maruoka, Y Konno, T Murakami

The iron ore sintering process produces approximately three per cent of carbon dioxide emission in Japan because a large amount of coke breeze is used as the main agglomeration agent. Therefore, its suppression has been required. A promising method is to replace the coke breeze with biomass char and iron-bearing materials. In this study, the effect of the utilisation of metallic iron with coke or palm kernel shell char (PKS char) as an agglomeration agent on its oxidation behaviour was examined by a series of experiments using a sintering simulator. The use of PKS char leads to a larger decrease in the pressure drop difference of the sintering bed compared to the case using coke. Furthermore, the oxidation rate of metallic iron was larger in the case using PKS char together than that using coke. It was considered that the oxidation of metallic iron was promoted because the bed-temperature increased at a faster rate and achieved a higher temperature.

Nov 8, 2021

Welcome to Mount Isa- my home city and without doubtthe base for what promises to be the most exciting mineral development yet seen in Australia.Mr. Chairman, it also gives me great pride to representthis area in the Queensland State Parliament as well as being the Minister for Minerals and Energy in the Queensland Government.Mount Isa is now part of the Australian mining industry folklore.It is all what a good mine is all about. It is. all what a good community is all about.

Jan 1, 1993

By J van Niekerk

The BIOX« process for the treatment of refractory gold ores and concentrates has been commercially in operation for 18 years. A total of six BIOX« operations have been successfully commissioned since the commercialisation of the process. Four of these BIOX« plants are still in operation today. There has been a renewed interest in the process the past few years with two BIOX« plants, the Suzdal plant in Kazakhstan and the Fosterville plant in Australia, scheduled for commissioning during 2004. Four new projects are also in various stages of development and are currently scheduled to be commissioned during 2005 and 2006. Research into the process are currently focussed on the two highest operating cost items for the commercial operations, namely power for agitation and air dispersion and cyanide consumption during leaching. Laboratory aeration and agitation testwork using the A340 up-pumping agitation system has shown that similar mass transfer rates can be achieved at slightly higher agitator power. The up-pumping system, however, eliminates the need for a separate blower and sparger system as air is introduced into the slurry from the slurry surface. The use of the thermophile bacteria as the final oxidation step during biooxidation has shown great promise. Reductions in cyanide consumption of up to 50 per cent were achieved when using the combination mesophile and thermophile process compared to standard BIOX« product solids. The combined process takes advantage of the milder oxidising conditions of the well known BIOX« process for the bulk of the oxidation and then uses the high temperature thermophile bacteria to complete the oxidation. The ASTERÖ process for the biological degradation of cyanide and thiocyanate containing effluent solutions has been proven to be efficient and stable. The process uses an activated sludge system with a residence time of approximately six hours in the sludge reactor. Heavy metals and metal cyanide species have also been shown to be removed successfully from solution.

Jan 1, 2004

The metallogenic belts of the Central Andes (iron, porphyry copper, polymetallic and tin) are genetically related to an eastward migrating magmatic arc. The polymetallic belt of the Bolivian Altiplano formed during Miocene arc broadening and lies in a critical position for understanding the genesis of this zonation. It is penecontemporaneous with parts of the copper and tin belts, and shares many characteristics with them. The differences between the belts result from contrasting volcanic and feeder stock geometry, depth of erosion and country rocks, and are not due to variations in magma chemistry, age or Benioff Zone depth. Polymetallic mineralisation in the Altiplano is epithermal in style and mostly related to flow-dome volcanism. The intermontane basinal setting precludes deep erosion to expose the epizonal feeder stocks and predicted porphyry copper mineralisation. In contrast, erosion of the less abundant stratovolcanoes of the Altiplano-Puna and Pampean Massif may expose contemporaneous Miocene porphyry copper mineralisation in subvolcanic stocks. The tin belt is coincident with the Paleozoic fold belt of the Eastern Cordillera. The occurrence of minor tin in Altiplano epithermal deposits hosted by Paleozoic sediments, and the persistence of tin mineralisation in the tin belt over 350Ma, suggests that Paleozoic sediments are the source of the tin.

Jan 1, 1987

Iron and steelmaking slags have been utilised for a century. All dumps are now exhausted. Because of constraints in establishing new stock yards, all slags have to be utilised immediately. At present, this is being achieved. Only in a situation where there is an increase in pig iron and crude steel production, together with the impact of new residual materials competing from other industries can marketing problems be anticipated.

Jan 1, 1979

By Higuchi K

For the mechanisation or automation of mining, recognition of the shape of mined cavities is basic information. A three dimensional shape measuring system, developed and tested, includes an ultrasonic range finder which is attached to the tip of a serial link manipulator. The range finder can be moved to any position and direction in the operational space of the manipulator. The position of a point on the surface of the object is obtained from the position of the range finder, the direction of the beam of the ultrasonic waves and the measuring distance of the range finder.To avoid collision between the sensor and the object, the manipulator is controlled to trace the surface of the object For the tracing control, another ultrasonic range finder is employed. The test results show that the developed system has high performance.

Jan 1, 1991