Search Documents

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 kilometres. Some 500 kilometres south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 kilometres. The Complex was emplaced at several centers along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite.

Jan 1, 1980

By Moffatt G

Approval to operate Longwall No. 7 at Appin Colliery in 1979 was granted pursuant not only to the usual statutory provisions, but also that an adequate means of drainage of methane gas be incorporated. A methane drainage plant was subsequently designed and constructed some two km from the pit top at the site of the Colliery main upcast and down cast shafts. Modern plants of this nature are completely automated using programmable controllers and computers to provide control and management reporting functions. Complex mechanical systems are installed to extract the gas and in handling and storage processes. Gas utilisation plants exist which can generate power from methane. These plants are further enhanced by harnessing waste heat produced in the generation process. The installation, automation control and monitoring of these plants incorporates many facets of engineering from high voltage power supply and computer technology to complex gas handling procedures used in gas compression storage.and generation of electric power.

Jan 1, 1982

Techniques and results achieved during the excavation of the Melbourne Underground Rail Loop (HURL) are summarised and discussed in the context of the various restraints present in a typical urban construction project. Mechanical methods (as distinct from those utilising blasting)accounted for the bulk of the excavation. Ground support was critical in this particular geological excavation setting, but is not discussed in detail except insofar as it constitutes a restraint to excavation progress.

Jan 1, 1978

By Percival T. J

Precious metal deposits containing fine-grained disseminated or dispersed gold-silver form by reactions between metal-bearing hydrothermal fluids and sedimentary host rocks. Host rock permeability and chemical composition exert a primary influence on the fluid movement necessary for any primary dispersion halos to form around ore bodies, and determine whether a disseminated style orebody itself will even form. Where the mineralized rocks are relatively unfractured the margins of the orebodies exhibit abrupt decreases in gold content, and strong corresponding decreases in the contents of other metals. Primary dispersion patterns of this type are difficult to recognize and commonly are only a few meters (or less) in width. If the host rocks were well shattered and broken before mineralization, remnant amounts of the hydrothermal fluids may be dissipated in fractures lateral to or above the ore zones. This causes geochemical anomalies to form with clays and silt- size silica within the fractures over distances of up to at least 30-50 meters away from the main orebodies. The tendency for large primary dispersion halos not to form around these deposits explains the disappointing results from so many drilling programs where no multi-gram gold-grade material was even found: if large areas and apparent large volumes of rock contain one gram or less gold that likely is the "orebody" and not a halo effect around high grade mineralization.

Jan 1, 1988

By Van Weert G

Ferrous chloride solution pyrohydrolysis is a successful IICI regeneration process which is carried out in either a spray roaster or a fluid bed. Pyrohydrolysis is not restricted to ferrous chloride only, every metal chloride can theoretically be hydrolysed. In practice, however, the conditions for ferrous chloride pyrohydrolysis differ from those of many non-ferrous metal chlorides eg zinc, lead and cadmium. Hence, a pyrohydrolyser could function as a ferrous/non-ferrous separator, eg an iron oxide and zinc chloride separator. Most pyrohydrolysers operate on solutions, in which case more than 50 per cent of the process energy is needed for heating and evaporating water. However, this disadvantage would be diminished by feeding a slurry to the reactor. Against this background it was decided to investigate the chloridisation of zinc ferrite which is an iron bearing solid with a non-ferrous impurity, and subject to processing and disposal problems. Synthetic zinc ferrite was chloridised in a tube furnace. The gas atmosphere in the tube furnace resembled that of a fluid bed pyrohydrolyser and consisted of HCI, 1120 and nitrogen. Gas composition, temperature, residence time and sample mass were varied. The experiments showed that complete (99.6 per cent) zinc extraction from synthetic zinc ferrite was possible in a simplified pyrohydrolyser atmosphere at 1100 K in four hours. The zinc ferrite was converted into gaseous zinc chloride, and hematite and magnetite solids. It was also found that zinc removal from the zinc ferrite lattice caused not only rccrystallisation of the zinc ferrite into hematite, but also hematite crystal

Jan 1, 1993

A short overview of the research program of SveBeFo, Swedish Rock Engineering Research, which was founded in 1993 is first given. Then four recent and ongoing projects in rock blasting and explosives engineering are presented in greater detail: 1. Burn Equations for Commercial Explosives. 2. Blast Damage in Contour Blasting. 3. The Role of Gas Pressure in Pit Wall Damage. 4. Fragmentation of Aggregate Rock. The goal of the bum equation project is to be able to control the energy release from explosive charges to the desired part of the expansion curve of the reaction products under various rock conditions. SveBeFo's work has reached the stage where a burn equation for a lab emulsion has been established which can model the influence of charge diameter on the VOD and detonation front curvature in a cylindrical charge quite well. This work now continues with other emulsion recipes. In the blast damage project the goal is to develop techniques and recommendations on how to minimise the blast damage in construction blasting. The project has gained extensive practical knowledge from the blasting of more than 200 holes in a granite quarry under controlled conditions. The cracks in the rock surrounding the contour holes have been cut open and measured. The influence of factors like charge concentration, decoupling ratio, hole and charge size, VOD and time delay in initiation have been investigated. A simultaneous initiation of a group of contour holes with EDD detonators is quite superior to single hole blasts, even when they are timed as closely as 1 ms.

Jan 1, 1995

There are many variables in a flotation concentrator, some of which are outside the actual flotation stage, which affect metallurgical performance. The number of such variables which can now be measured on a continuous basis has increased significantly over the past 20 years. They can be broadly classified under the headings of physical, chemical, and elemental. In this paper reference is made to a number of such variables, and comment is made on the state of the art in their measurement. Although not confined to development in Australia, particular reference is made to the considerable Australian contribution in this area of Technology.

Jan 1, 1984

The author describes 1. The classification and characteristics of various thick seam mining techniques in various Japanese coal mines. 2. Practices of thick seam mining methods experienced in Taiheiyo Coal Mine. Currently, thick single lift, simultaneous multi lift and non simul- taneous multi lift mining methods are adopted as underground flat thick seam excavations in Japan. These are now reliable and effective in increasing the extraction ratio. At Kushiro Colliery of Taiheiyo Coal Mining Co., these three thick seam mining methods have been used. According to the results, if solidification of the top lift goaf is essential, the non simul- taneous multi lift mining method is the most effective in increasing the extraction ratio without minimising productivity of each lift and it points out that further development of this method is necessary.

Jan 1, 1976

By Sauer P

The features of Banana screens have been known for some considerable time and recently considerable interest has been generated in the performance of these units. This paper reviews screening principles on Banana and conventional units and demonstrates the capacity and effic- iency of these units. Furthermore, the behaviour of modern Banana screens and modem screens in general, are examined with respect to life, vibration isolation, noise emission and maintenance requirements.

Jan 1, 1978

By Katsuyama K, Nag DK

Three aspects of rock mechanics, namely, in-situ stress estimation by acoustic emission (AE) method, strength of rock mass and role of chemicals to reduce the strength are covered. It is possible to detect the previously applied maximum stress by stressing a rock specimen to the point where there is a substantial increase in AE activity. This is known as Kaiser effect. From the AE signatures in the second and subsequent loadings, AE take-off point was identified more easily than in the first loading. In determining the compressive strength of rock mass, two factors have to be considered, namely, the size effect on the compressive strength of intact rock and the effect of discontinuities on the compressive strength of rock mass. Although a modified Bieniawski criterion gives best agreement with the triaxial test data, modifications have been suggested to Hoek-Brown criterion due to its popularity. It is possible to reduce the tensile strength of sandstone by saturating it with weak chemical solutions made with dodecyltrimethyl ammonium bromide, polyethylene oxide and aluminium chloride by up to 30%. In the case of compressive strength, there is no appreciable effect. The possible explanation is that the chemical solutions produce an effect on the strength of sandstone only when the failure mechanism is dominated by tensile mode.

Jan 1, 1998

This paper describes the programing and specification requirements which affected the choice of excavation methods on the Melbourne Underground Rail Loop (M.U.R.L.). The various methods that were chosen are briefly described, and the three most used are compared in more detail. Excavation rates, cycle times and other statistics are compared for full face tunnel boring, full face drill and blast, and heading and bench using a road header excava- ting machine. The length of tunnel excavated is sufficient to enable meaningful statistics to be presented and the significant specifi- cation and geological factors are described to weight the statistics where necessary for purposes of comparison. Average tender prices are given for excavation and primary support to indicate the reimbursement sought by contractors to carry out this type of tunnelling.

Jan 1, 1981

SITUATED in the county of Manchcster, in Northern Eyre's Peninsula, the Iron Knob ore-deposits form the basis of the industry. These deposits are connected by the Iron Knob tramway to the port of Whyalla, aal miles distant, on the western shore of Speneer Gulf,and to-day another tramway is under construction to link up with the same port, a second group of iron ore leases known as Iron Baron, which is situated 18 miles south of Iron Knob. Fig. 1 indicates the geographical relationship of these three places, Iron Knob, Iron Baron, and Whyalla, which together comprise this field of the company's activities.

Jan 1, 1930

By Dharmappa HB, Sivakumar M

This paper is concerned with two case histories of wastewater quality management in underground coal mines in the Illawarra region. The first investigation briefly presents an analysis of mine water discharge having an extremely high concentration of suspended solids and consistently high barium concentrations, averaging, 14.4 mg/I Barium, over the sampling period. A laboratory study of chemical precipitation processes has indicated that about 91% of barium could be removed by using ferric sulphate and lime. On the basis of the information obtained from the environmental audit process an alternative water treatment and reuse system incorporating 51% reduction in the water consumption with 32% less off-site discharge has been suggested (Thomas, 1995).The second case history is concerned with the storm water management at a mine situated in the Illawarra escarpment where only 20% of the wastewater generated in the colliery is discharged off-site. Computer modelling of the storm water system showed that 75% of the clean runoff becomes contaminated through poor management practices and causes the process wastewater treatment system to fail in wet weather. Suggested improvements include relatively simple alteration to the coal wash filtration dams which are expected to reduce the periods of inefficient operation of these dams by 95%. The use of storm water diversion channels and detention basins can reduce the overflow volumes by 70 - 100 % for a ten year ARI (Average Recurrence Interval) storm event (Wingrove 1996).

Jan 1, 1998

By J Zanganeh, M Ajrash, B Moghtaderi

Application of thermal oxidation is considered a promising technique in reducing fugitive methane gas from ventilation air methane (VAM). A typical thermal oxidiser operates with diluted methane and converts it to less potent greenhouse gases. However, having a thermal oxidiser in the vicinity of the coalmine exhaust shaft is a major safety concern as its high operation temperature increases the likelihood of accidental fire and explosion. The aim of this study is to investigate the application and effectiveness of side venting technique in reduction of deflagration consequences caused by methane gas. To address this importance a series of experiments were conducted on a detonation tube designed and fabricated as part of larger scale VAM Abatement safety project. The experimental work was carried out into two stages: examine the flame and explosion properties in a large-scale detonation tube to get reliable data; and then design and employ a venting system into the detonation tube to verify the effectiveness and performance of the venting against the flame and explosion.Results corresponding to this study show that the side vent duct with venting coefficient magnitude of 37 had a significant influence on methane flame deflagration and the explosion characteristics. The maximum pressure rise at the detonation tube reduced approximately 20 per cent to 32 per cent by applying the side venting duct. Also, the data shows that the venting damped the pressure oscillation after the flame deflagration which eventually reduced the system instability. Finally, by applying the venting technique the expected level of damage due to the dynamic pressure reduced to the level of limited building damage.CITATION:Ajrash, M, Zanganeh, J and Moghtaderi, B, 2017. Application of side venting technique in mitigation of methane – air explosion and flame deflagration in ventilation air methane, in Proceedings Australian Mine Vent Conference 2017, pp 153–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Types of structure found in 'Jest Australian beach sands are described. Their recognition by geostatistical methods follows nth a discussion of the effectiveness of sampling patterns. Examples of structures are given, and an account of their effect on valuation procedures.

Jan 1, 1977

By J Manuel, R Muddle

The demand for iron ore has increased significantly in recent years, with new iron ore sources being mined to meet this demand. As the composition of sinter blends changes with the availability and cost of iron ore, so too does interest in the impact of new ore types on granulation and ultimately productivity. This paper describes a study into granulating characteristics of seven iron ore types, including various hematite and goethite ores. The effect of ore type on feed moisture requirements, green bed permeability, green bed strength and granule size distribution was examined for single ore blends containing coke, flux and returns. The ore size distribution was varied in these blends and its effect on granulating characteristics examined. It was found that the optimum moisture requirement of the ore was more dependent on ore type than ore size distribution, but ore size distribution (and specifically intermediate particle loading) had a greater effect on green bed permeability. The saturation moisture value for an ore was found useful in predicting both optimum granulation moisture and green bed permeability.

Jan 1, 2005

The Lake Rotokaua sulphur deposit, near Taupo, New Zealand, is a lacustrine sedimentary ore body, 220 acres in area and from 7 ft to 96 ft thick, containing, within the area drilled to date, some 20 million long tons of ore averaging 25% elemental sulphur in unconsolidated tuffaceous diatomaceous clay, overlain by about 120 ft of pumice sand and by the shallow Lake Rotokaua. An additional amount of perhaps 4 million tons of sulphur is regarded as probable in the area remaining to be drilled. Current economic studies cover the problems of mining an unconsolidated water-saturated formation with some residual thermal activity nearby; conservation and restoration after mining in a scenic recreation area; beneficiation of the ore and extraction of high- purity sulphur, principally for fertilizer manufacture. The deposit has additional importance as a pointer to possible further discoveries in the Thermal Region.\

Jan 1, 1971

By Smith F. A, Both R. A

The application of biogeochemical methods in mineral exploration in the semi-arid to and environment of Western Australia was investiga- ted in an area near Norseman. The reliability of these methods was evaluated by comparing trace element characteristics of rock, soil and plants in the vicinity of the Pioneer BB pros- pect. The prospect is located in the south- western part of the Pioneer Dome, where granite gneiss core is surrounded by a 'greenstone' sequence of ultrabasic, basic and sedimentary rocks. Nickel-iron sulphide mineralization occurs discontinuously along one of the basic- ultrabasic contacts. Analyses of unweathered and partly weath- ered rock from diamond drill cores show the ultrabasic rock to be highly variable with re- spect to nickel, copper, cobalt, zinc and manga- nese. Samples of weathered bedrock and over- lying soil were analysed both for total trace element contents and for the trace elements associated with secondary iron and manganese oxides. Approximately 30 per cent of the total nickel content of the weathered basic rock is associated with secondary iron and manganese oxides, compared to approximately 15 per cent in the weathered ultrabasic rock. The soil is partly transported but has a residual component sufficient to provide a reli- able indication of the underlying rock chemistry, although the trace element content of the soil is less variable than that of the rock. Total

Jan 1, 1973

By Bond W. F, Sharry P. V, Onley P. G

The use of Decision Analysis is becoming more widespread in industry as a whole, and there is considerable scope for its application in the mining industry. Wherever decisions have to be made, whenever risks have to be taken, whenever uncertainty exists or whenever judgements have to be made, then Decision Analysis can be used. In the mining industry we daily make many decisions involving risk, uncertainty and judgement. Expansion and diversity will only increase the need for balanced decision making techniques. This paper seeks to describe the history and principles of Decision Theory, and to illustrate the various modelling approaches using three fictitious yet realistic case studies. Decision Analysis logically integrates the quantifiable and seemingly non-quantifiable aspects of a decision problem into a coherent, explicit and rational solution. It also allows the decision-makers to see the full impact of each variable or uncertainty, and hence focus on the key aspects that influence the solution.

Jan 1, 1996

By Grieveson P, Rajakumar V

The reduction of an ilmenite concentrate with coal at 1000, 1050 and 1100¦C was investigated using thermogravimetry and X-ray diffraction, optical microscopy and electron probe microanalysis of the product. The effects of temperature, coal particle size, addition of ferric chloride and preheating of the concentrate in argon on the reduction kinetics and mechanism were determined. The rate of reduction increased significantly with temperature and was enhanced by the addition of the catalyst. The morphology of the iron was primarily determined by the degree of weathering of the particle. Significant coarsening of iron was obtained in the dense particles by the addition of ferric chloride. The sequence of reduction and the enhancement in the rate of reduction by preheating the concentrate in an inert atmosphere are discussed.

Jan 1, 1991