Search Documents

For the past five years the University of Queenslandhas, through its various workshops, been preaching to Australia that there was a potentially hazardous situation from earthquakes for urban Australia. A few people outside The University accepted this, but largely the warnings fell on deaf ears.The 1989 Newcastle earthquake changed that per-ception. The most important lessons to emerge from Newcastle were (i)the realization that in continental areas small earthquakes cause widespread damage:(ii)the local geology of an area is of great importance in the damage done by an earthquake.These two factors clearly indicate that, in the future, we must take far greater account of the "Urban Geology" of an area. This paper discusses the need for urban geology and its impact on seismic risk and compares that with the traditional methods of assessing seismic risk.

Jan 1, 1990

By Lawson F

Synthetic calaverite (Au Tez) has been prepared and its physical properties checked.Simple flotation tests indicate that the recovery of calaverite should be possible using n-butyl or sec-butyl xanthate collectors under approximately pi I neutral conditions with a copper sulphate activator.Roasting calaverite in air at moderate temperatures resulted in its decomposition with the formation of elemental gold and tellurium dioxide.In alkaline oxygenated cyanide solutions, both gold and tellurium tend to dissolve. At pHs less than 14, about 50 per cent of the tellurium remains as elemental tellurium; however in very strongly alkaline solutions, essentially all of the tellurium is converted to the soluble tellurite ion (TeOl-).However, even at high pHs, the solubility of gold in the cyanide solution is still low due almost certainly to passivation effects.

Jan 1, 1991

By Jorgensen FRA, Moyle FJ, Turner TM

Laminar flow furnace techniques and thermal analysis were used to study the combustion of Kambalda nickel concentrate and Collie coal. The study was made to ascertain the suitability of the latter as a replacement for the fuel oil currently burnt in a flash furnace at the Kal- goorlie Nickel Smelter. The coal was found to ignite at temperatures between 500-600¦C which was the same as that required for the most reac- tive component of the concentrate, namely py- rite. The rates of reaction of both the coal and concentrate were dependent on oxygen con- centration. Sulfur dioxide hindered the combus- tion of concentrate and of coal, the effect on the concentrate being the more pronounced. The effects of moisture content and the tendency for spontaneous combustion of the coal were also noted.

Jan 1, 1982

By M Stewart, J Vann, A Bu, D Frederickson

The Golden Gift is a recently discovered deep deposit below the main operating areas of the Stawell Gold Mine. At an early stage of the project, diamond drilling was used to define the mineralisation on sections approximately 100 - 150 m apart. The project economics were sensitive to both grade and tonnage. There were consequently two significant risks on resource quantification: risk on tonnage (ægeological riskÆ); and risk on grade (ægrade riskÆ). The degrees of freedom inherent in the geological model were considered to be potentially high because of wide drill spacing and likely structural complexity. To quantify geological risk three geologists familiar with Stawell mineralisation independently interpreted the deposit. This generated three plausible, different geological volume models. Conditional simulation was then used to quantify grade risk. Conditional simulation requires the user to define input statistics (histogram and variogram model) and a geological envelope. Based on global mean grade of an ordered set of simulations, æpessimisticÆ, æmedianÆ and æoptimisticÆ simulation cases were defined. The result was a 3 x 3 risk matrix with geological risk (the three interpretations) on one axis and grade risk (also three cases) on the other axis. An interesting result was that geological and grade risks were of a similar order of magnitude. Therefore a risk analysis of grade by geostatistical methods within a fixed geological model is of limited value, especially if the drill spacing is wide. After completion of this study, with additional drilling, the geological degrees of freedom at Golden Gift reduced substantially. A second Golden Gift risk study used a refined geological model to build a set of simulations to be used in preliminary mine design. A third simulation study in the deeper parts of the Magdala ore deposit, a well-drilled part of the mine with production history, demonstrates that the geostatistical simulation method used at Golden Gift is a robust and useful tool to quantify grade risk.

Jan 1, 2003

By Kubik K

The objective of this paper was to determine if recent advances in numerical electromagnetic wave propagation modelling techniques could be used to study the propagation of GPS signals over arbitrary terrain. Specifically the effects of diffraction and multipath were to be modelled accurately for propagation over arbitrary terrain surfaces defined by a digital terrain model. Ideally the model was to be in three dimensions and cover an area of a few square kilometres with a simulation height of a few hundred metres. Simulations were to run on current technology PC's with run times less than a few hours. A relatively new technique that involves a numerical solution to the Parabolic Equations can be used to solve for two-dimensional propagation over any type of terrain. The PE provides a direct solution of Maxwell's wave equations by approximating the Helmholtz scalar wave equation. This technique does not rely on the study of individual ray paths as used in the Geometrical Theory of Diffraction (GTD). It was decided to develop a two dimensional Parabolic Equation code, using the Fourier Split/Step method that allowed propagation over arbitrary terrain (; ; ). The model boundary conditions assumed that the satellite transmission was a plane wave, and that the lower boundary was a perfect reflector. Propagation simulations from the model accurately provide the amplitude and phase of the propagated plane wave at all points within the model domain. The PE model was used to study the effects of diffraction and multipath caused by various types of terrain commonly found in an open cut mining environment. The study of diffraction errors was relatively simple, because we are simply concerned with amplitude of the signal as it diffracts about an obstacle. If the amplitude is above the level receivable by a GPS receiver then the diffraction error can be obtained from the geometry of the terrain obstacle. The study of multipath is more complex, as the computed phase from the PE model is ambiguous and the presence of multipath can only be inferred. Thus the absolute magnitude of the nmltipath error is not currently determinable, though the results of some new work is shown here. This paper shows that diffraction effects can cause significant errors in range. It also shows the effects that multipath has on the received amplitude of the signal and the received phase of the signal. A discussion is made of further work that is presently underway that will allow the direct determination of the multipath error by comparing the ambiguous phase with a reference phase.

Jan 1, 1997

By Delahey G, Dunne R

At New Celebration Gold Mine the advent of treating primary sulphide ores resulted in decreased gold recoveries of four to ten per cent. The grind coarsened due to an increase in ore hardness and gold in the residue was found to be associated with pyrite. Finer grinding improved recoveries but was impractical as production rates would have decreased to unacceptable levels. An alternative approach that has proved to be viable combines both gravity separation, to recover the coarse gold bearing sulphides, and then regrinding the concentrate in a tower mill prior to releaching in the cyanide leach circuit. The tailings treatment plant was commissioned in December 1990 and details of the first 18 months' operations are Provided.

Jan 1, 1993

By Cox LT

A short term tyre study of trucks operating in a multiple pit surface coal mine showed significant potential for cost savings. The tyre study, conducted on-site over a three months period covered a mixed fleet of 18 trucks ranging from 27 tonne to 77 tonne capacity operating on overburden removal, coal haulage and watering duties. Some existing plant history records and a variety of tyre related measurements during the course of the study allowed the current state of tyre operations to be quantified. Specific attention was given to determining ger>ral trends from historical records and conducting detailed studies of individual lug damage, pressure monitoring and rectification, as well as tyre maintenance procedures. Important haul road parameters including camber, gradient, curve radii and superelevation, constructional materials and surface clean-up were appraised for their influence on tyre wear. Recommendations for achieving long term cost effective tyre utilisation included increased tyre maintenance, personnel development, compliance with haul road design parameters and more stringent clean-up Procedures.

Jan 1, 1982

By Mortimer RR

The Weipa bauxite mining operation on the west coast of Cape York currently mines lb million tonnes of crude ore per year from the Andoom and Weipa mines. Andoom ore is trucked up to 4 km to a rail load station and hauled 20 km by train to the Beneficiation Plant. Weipa ore is trucked up to 7 km to the Beneficiation Plant. Increasing haul lengths and production requirements have led to a progression of larger two axle rear dump trucks and currently he intrcducticn of 145-tonne, three axle L t Dm dump trucks. bith the introduction of the Andoom a operation in 1972, the decision was made to use a railway system to haul crude ore from Andoom to Weipa. This system has proved to be successful from both an economical and operational view point. Due to the successful combination of a truck and rail haulage operation in Andoom, future :evelopment of orebodies requiring increased haul distances and increased production tonnages will probably result in extension r>f the railway system to compliment the trucking operation from the mine face.

Jan 1, 1978

By Waladan M, Elliot B, Rankin W. J

A survey was undertaken on the Kalgoorlie Nickel Smelter in which samples of slag and matte were taken along the length of the integrated flash smelting furnace and analysed to determine the variation of nickel and iron concentration. At the same time the oxygen potential of the slag and matte was measured using disposable tip solid-state oxygen probes. The results show that the oxygen potential of the slag is higher than that of the matte and that both decrease from the reaction shaft end to the slag tap hole end of the furnace. The slag and matte are not at equilibrium except towards the tap hole end. Reduction of nickel and magnetite from the slag occurs before the slag enters the slag-cleaning appendage by reaction with iron in the matte. Thermodynamic modelling and laboratory experiments showed that the equilibrium nickel and magnetite contents of the slag in the absence of a carbonaceous reducing agent are about 0.4 per cent and 7.5 per cent, respectively. A carbonaceous reductant is required to obtain a lower nickel content in the slag.

Jan 1, 1991

This paper describes a case history of using an integrated geochemical and hydrogeological approach to predicting solute transport from gold mine tailings in highly fractured volcanic terrain. Two modes of transport are identified, namely discrete fissure flow and diffuse seepage through the intervening weathered rock. A simple mass balance approach is used to predict concentrations at points of emergence because most of the seepage migration will be by way of the discrete fissures where advective transport will predominate. The mass balance method has been modified to allow for natural degradation of weak acid dissociable cyanide. The long term effects of diffuse seepage are also examined.

Jan 1, 1988

Establishing the link between the solid, cold rock of dikes, sills, plutons, and lavas and hot, active magma chambers is the quest of igneous petrology. Differentiation of Earth, the diversity of the igneous rocks, and the spectacle of volcanism are ample evidence that magmatic processes are fundamental to our understanding of planet formation and evolution. Single gabbroic plutons, on the other hand, often show intricate and abundant evidence of the effects of crystal growth and sorting. It has not proven simple, however, to establish the basic principles of magmatic behavior leading to this crucial evidence. Because of their abundance, exposure, simple geometry, large range in size, and often straight-forward petrology, sills are excellent examples of the magma chambers. Physical and chemical processes operating in sills can be recognized that also routinely operate in many other bodies. Understanding the dynamics of sill solidification is essential to understanding the genetic links between lavas and plutons.

Jan 1, 1990

By L M. Foster, J R. Kellett, G A. McMah

The Great Artesian Basin (GAB) contains one of the largest reserves of fresh water in the world. The volume in storage is enormous, being estimated at nearly 65 000 million megalitres (ML). Development of this resource, dominantly for the pastoral industry, began in the late-1800s and quickly accelerated. With exploitation of the resource, artesian pressures declined almost as rapidly. This loss of head is a result of the total discharge from the basin and much of this discharge is waste of water. The waste through uncontrolled bores and inefficient distribution systems still amounts to about 75 per cent of all discharge. However, the volume in storage has hardly been depleted. The major concern is the effect of withdrawal on artesian pressures. Due to the size of the Basin, the relatively flat gradients and low permeability, the movement of water through the aquifers is extremely slow and independent of recharge. Hence, the normal concepts of sustainable yield (ie discharge should equal recharge) cannot be applied to the Basin as a whole as travel times do not allow for the effect of recharge to be seen away from the outcrop areas within management timeframes. The large volume in storage, though, can provide an extensive buffer to the impacts of temporary water needs. This effect should be considered when assessing the acceptability of fixed life projects such as mines and the extracted volumes from their operations. Identifying a sustainable yield involves balancing the acceptability of the economic, environmental and social costs with the associated discharge and fall in head, to arrive at an acceptable balance.

Jan 1, 2003

By Loo C. E

Thirty two polyacrylamide flocculant samples were selected from the wide range offered to the Australian coal industry. An extensive test program was conducted to consider the properties of the flocculants, the substrates, the process conditions and the water chemistry encountered in coal preparation plants. The study indicated that flocculants with molecular weights of 12 to 14 million and degree of hydrolysis around 40% gave the best "average" performance over a wide range of process conditions. The pick-up and filtration of fine coal was demonstrated on a pilot scale to be a critical function of flocculant properties. This study also showed that the agitation intensity during flocculation was a critical parameter in determining the settling rate of the slurry and the clarity of the resulting supernatant. An electronic meter to measure agitation intensity was designed, constructed and tested to demonstrate how, for the first time, laboratory results can be implemented in operating plants.

Jan 1, 1989

By Wang SS, Frattaroll DR

In the development of novel sulfide collectors, especially for the low-lime and acid circuits, flotation of chalcopyrite, chalcocite, covellite and pyrite was studied with both new and commercially available S- containing collectors. The natural float- ability of sulfides, water quality, and redox potentials - all of which were considered im- portant in assessing collector strength and selectivity - were also investigated. Chalcopyrite exhibited the highest natural floatability. The response to most collectors, however, was chalcocite > covellite > chalcopyrite > pyrite. Water quality had a very significant effect on both natural and collector-aided floatability. De- ionized water and tap water had a flotation suppression effect compared with doubly- distilled water. Flotation results with single minerals are correlated with those for copper and pyrite from natural ores. Several novel collectors have now been developed for sulfide flotation in acid, neutral or mildly alkaline circuits. The results for four of these collectors, which have shown promise in commercial applications, are discussed in this paper.

Jan 1, 1986

Both safety and productivity in underground gassy coal mines can be improved substantially if an appropriate gas management system is introduced. A strong direct relationship exists between the gas emission rate, roof and floor strata relaxation zones characteristic, mining activities and gas drainage practices. Detailed knowledge of geological factors, gas and coal-rock properties, as well as mining systems are necessary for the methodology used in predicting overall underground gassiness, and planning gas capture and ventilation systems. Early gas emission calculations for various mining activities, particularly for the longwall mining system are essential. A reasonably accurate prediction of gas make as well as the design of ventilation, gas recovery (drainage holes) techniques can be made using 'Floorgas' and 'Roofgas' computer simulations, provided sufficient geological, mining, and gas data are made available.

Jan 1, 1998

This paper examines the cost and economic consequences of varying a number of key factors in the course of developing and operating new underground longwall coal mines with both shallow and deep cover in New South Wales. The economics of the project are assessed for the first 20 years of mine life using the discounted cash flow method with produc- tion and selling price being determined to provide break even costs for a range of minimum rates of return.

Jan 1, 1988

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

By Hare S. M, Griffin P. T, O&apos

Chalcopyrite ore and converter slag treatment to produce copper concentrates is undertaken at the Copper Concentrator of Mount Isa Mines Limited. This concentrator was commissioned in May 1973, replacing the original No 1 Lead-Zinc Concentrator, for the processing of all chalcopyrite ore coming from Mount Isa Mine.Treatment of chalcopyrite ore at rates of up to 125 000 l/week is described here; the treatment of converter slag is described later.

Jan 1, 1993

A review is given of the development of the author's ideas on the relationship of ore occurrence to regional dislocations in the earth's crust, presently identifiable in particular areas as linear discontinuities in patterns of geological and geophysical data. Ideas originating from field observations in Broken Hill were developed in conjunction with three-dimensional kinematic deformation models which were devised to simulate rock structures, and to illustrate their response to assumed linear and planar movements at the scale of mine and regional geology. These led to the study of linear features in the pattern of Broken Hill district geology, and to the observation that the Broken Hill lode occupies a "cross-roads" position at the intersection of regional geological lineaments where they cross through and deflect the host rocks. A genetic association was therefore proposed. The recognition of significant regional lineaments requires special techniques and treatments of field data originally developed for the Broken Hill situation. The subsequent application of the work to the Western Australian shield revealed that known major nickel and gold deposits also occur where the host rocks are crossed by one or more regional lineaments. These lineaments were recognised as part of a continental tectonic pattern of major linear trends with which major ore deposits are associated. The ideas were later used in exploration leading to the discovery of the Olympic Dam deposit at Roxby Downs, South Australia, which is related to regional lineaments.

Jan 1, 1983

By Mitchell D

In recent years the need to provide increased ventilation to improve environmental conditions rather than to dilute firedamp has led to increasing interest in the use of recirculation. Present UK mining law prohibits recirculation in ventilation, but it has been permitted selectively by exemption granted by Hm Inspectorate of Mines and Quarries. The conditions of use imposed by these exemptions to safeguard the safety and health of miners are examined in detail, dealing separately with primary and auxiliary recirculation systems.

Jan 1, 1988