Search Documents

By Horrocks KRS, Smitham JB, Ellison JF

This paper describes the development and installation of equipment for continuously measuring separating density in the dense medium cyclone circuits of the four million tpa Port Kembla B/C plant coal washeries. Monitoring equipment consisting of magnetic coils and differential pressure cells were installed in U-tubes taking the full flow of magnetite from the drain sections of the product drain and rinse screens. The monitoring equipment measures overflow magnetics concentration and overflow density continuously and has operated since 1989. From these measurements and calibration trials, the separating density of operating cyclone modules can be inferred reliably. Variographic analyses of the data show that medium density control to +/- 0.002 RD units and separation density control to +/- 0.007 RD units are achievable. Either method for measuring separation density can be used with approximately the same accuracy, although the overflow density measurement technique suffers from the need to have regular flushing of the Dp cells which complicates the signal analysis. Data from the plant shows that separation density can be controlled by regulating medium density, but the assumption of a constant offset between medium density and separation density is erroneous.

Jan 1, 1993

By Poole GR

An unusually high flow of water from an oxtr.iction panel in Wongawilli Colliery pr,;npted the investigation of the possible sources of the water. It is more probable that water is derived f r,m sources adjacent to or within the Woo ' iwi 1 I i Coal rat her than by direct t r.onnuni n i"n from any surface source.

Jan 1, 1986

By A Black, J H. Youngson

At least 85 000 tonnes of mine tailings were discharged into Deepdell Creek, east Otago between 1890s and 1940s. The tailings contained about 1 wt % arsenic, so about 850 tonnes of arsenic in the form of arsenopyrite was discharged. Annual floods have removed nearly all tailings within c. 60 years. Small amounts of arsenic-bearing sediments (<250 ppm) remain in Deepdell Creek. About 7 kg/year dissolved arsenic was discharged in groundwater from mineralised Hyde-Macraes Shear Zone rocks in the vicinity of the historic mine sites. Adsorption of this arsenic on to iron oxyhydroxides in the stream sediments may have contributed to the elevated As content of those sediments. Even less arsenic remains in the main Shag valley below the Deepdell Creek confluence (15 - 25 ppm As). Rare relict arsenopyrite grains are trapped in bedrock crevices 25 km from source. No tailings deposition is detectable in theShag River estuary, and the tailings have presumably been discharged into the sea. Natural rehabilitation of the Shag catchment has been rapid and effective.

Jan 1, 2004

By Pilkington T, Noy A

The Yallourn North Extension (YNX) open cut mine ceased mining operations in early 1989. YNX may be used again for coal supply at the discretion of the Coal Corporation Of Victoria (CCV); this has resulted in the need for interim rehabilitation of the site which may last many years, or indeed, permanently.The site has suffered substantial surface erosion over the years with large areas of bare clay and coal batters remaining exposed. The first priority is to reduce the quantity and improve the quality of stormwater runoff from the site. This is best achieved by appropriate revegetation and the use of existing landform depressions as silt trap/wetland areas. Proposed rehabilitation needed to take into account the sensitive fire safety of the open cut and the option to re-open the mine if CCV deems appropriate.The authors detail the factors involved in the rehabilitation proposal and the multi-disciplinary approach to planning including engineers, scientists, a forester, landscape architects and community input. The rehabilitation design included early consideration of land use and ongoing maintenance issues linked to water quality improvement factors including vegetation. Engineering input was required for reshaping and clay covering exposed coal batters and the design of silt traps which will revert to wetlands in future. The integration of each discipline has produced a rehabilitation design pleasing to both the SECV and community alike.

Jan 1, 1992

By Peck J. P, Kennedy D

Drill performance monitoring studies were recently completed at the Fording River mine, British Columbia. Microprocessor-based instrumen- tation and data analysis techniques were developed with the objective to improve short and long term mine planning. Data analysis permitted the identification of thicknesses and interfaces between soft/hard zones at depth based upon the recorded responses of the drill. Data clearly con- trast the soft coal seams and harder waste rock units based on variations in recorded drill rotary speed and torque, hydraulic downpressure, bail- ing air pressure and instantaneous rate of penetration. These parameters were monitored and recorded at 10 cm sampling intervals. Processed drill data was correlated with gamma logs, an existing means for locating coal seams and distinguishing between waste units. Current development of a pattern recognition module aims towards automated interpretation of drill data, identifying micro-and macro-geological and geomechanical rock mass characteristics. Delay between acquiring, processing and interpret- ing the drill data for practical use by mine personnel should be minimized. Integration of this technology with the mine's current main-frame based Mine Engineering Application System software will enable more accurate and timely annlication of the nrocessed drill data.

Jan 1, 1989

By La Brooy S R, Fenton K

A low grade copper flotation tailing from Telfer containing 1.2% Cu as chalcocite and cuprite and 5 gt-t Au was leached with ammonia, cyanide and ammonia-cyanide mixtures to extract copper and/or gold. Direct cyanidation extracted both copper and gold but consumed about 30 kgt 1 NaCN. Pre-leaching the tailing with an aerated ammonia solution containing 28 kgt 1NH3 and 17 kgtl(NHa)2S0a at pH 10 readily extracted up to 95% Cu in about 6 hours under optimum conditions. However pH and total ammonia concentration were critical factors. Subsequent cyanidation ex- tracted 80% Au using 6 kgt NNaCN. Ammonia-cyanide mixtures werefound to selectively leach gold over copper depending on the concentration and relative proportion of NH3 and CN. The best composition for leaching up to 80% Au from Teller tailing was 1.6 kgt t NaCN and 1.1 kgf 1 NH3 in the presence of 0.3 kgt t Cue+. Such a mixture left only 50 mgL-1Cu in the final solution after precipitation of some of the initially dissolved copper.

Jan 1, 1991

By O. J. RICHARDS

The Wongawilli system of mining has been in use for over 30 years and has enabled high production rates and acceptable extraction ratios to be achieved in seams less than 4 m in thickness. A modification of the Wongawilli system has been developed to permit the use of a continuous miner and mobile equipment to extract a coal seam 6 m thick. Following physical and mathematical model studies the new mining method is now undergoing field trials at Collinsville, Queensland. Progress of the field trials to date has achieved 99% extraction of the upper slice by remote control operation of the continuous miner and established the feasibility of installing resin grouted wooden dowels in the coal floor to reinforce the coal septum. The method is explained in the text.

Jan 1, 1980

By Soma T

Pyrite and Cu-concentrate were roasted in vertically suspended state in an externally heated tube. Tubes of three different lengths of reaction zone were used for three different reaction times. Roasted ores were submitted to chemical analysis and the extent of roasting reactions was determined. In case of pyrite, extent of roasting reactions was not affected much by reactor length and heating temperature (above 500¦C), but was considerably by ore/air ratio. Micro- scopic and XMA examinations led to the conclus- ion that pyrite particles decomposed to pyrrho- tite and then pyrrhotite was oxidized to give Fe-S-0 melt, magnetite and hematite. The extent of reaction was not uniform in all particles but had a wide distribution from unreacted pyrite to completely oxidized particles. Combustion of Cu-concentrate from Kuroko complex sulfide ore ) was unstable under a uniform wall temperature of 450¦C, but proceed- ed rapidly at temperatures above 500¦C. Sticking of roasted ores to the wall of the reaction tube induced choking of the tube, caused by melting of roasted ores, at tempera- tures above 950¦C. Enrichment of oxygen exterted less influence on reaction rate than heating temperature of the tube. Particle size of ore had a big effect on reaction rate.

Jan 1, 1980

By Armstrong AB

It has been identified that particulate matter in the form of suspended solids and bed load has the ability to adsorb heavy metals. Each year Ranger Uranium Mines Pty Ltd (RUM) identifies potential danger areas which could become major sediment sources during the wet season. Methods of suppressing sediment uptake such as hydromulching and coating areas with Poly Vinyl Acetate (PVA) glue are used. Other methods of reducing the sediment load after uptake such as diversion bunds, filters across drains, stone filters, minor sumps and settling ponds are also used. The 1983/84 wet season saw drain sediment loads reduced to acceptable levels before the water reached the outside environment. Studies to qualify and quantify flows from minor drains are still underway.

Jan 1, 1984

Mining software packages are used extensively in industry for resource estimation as well as for mine design and operation. Research undertaken in the W H Bryan Mining Geology Research Unit at the University of Queensland has shown that modifi

Jan 1, 1994

By Tobin GJ

Testwork carried out in the cooling water circuit at the Yabulu treatment plant of the Greenvale Joint Venturers (Metals Exploration Queensland Pty. Ltd. and Freeport Queensland Nickel Incorporated) since 1980 has resulted in significant improvements to both fouling and corrosion control. At the same time corrosion inhibitor costs have been reduced.Acrylate-type silt dispersants were identified as the most effective means of sediment control in the circuit. An increase in the cathodic component of the corrosion inhibitor coupled with a relatively minor adjustment to water pH has yielded a two to three fold reduction in corrosion rate. It has been established that these lower corrosion rates can be sustained in the face of a 20% reduction in corrosion inhibitor addition rate. Further improvements are indicated with a change of raw water algicide.

Jan 1, 1985

By M McGeough

Following the success of calcrete sampling at Challenger, calcrete sampling has been widely adopted as the primary exploration technique for gold exploration, in the Gawler Craton. Calcrete is uniformly distributed over large areas and produces discrete gold anomalies. This allows drilling to focus on specific gold anomalous targets. However, despite widespread use of calcrete sampling, very little is known of the origin of calcrete in the Gawler Craton, and the link between calcrete gold anomalies and primary mineralisation. In an attempt to understand this association Lisa Gibbons recently completed an honours project at the Old Well Prospect approximately 45 km SSE of Tarcoola. Her work is part of a collaboration between CRCLEME, MESA and MIM Exploration. At Old Well, a calcrete anomaly (>10 ppb Au)covers an area approximately 7 km x 2 km with a peak value of 97 ppb Au. The study looked at the regolith as a whole, processes of its formation and nature of mineralisation within it. She was able to combine previous calcrete and drilling results with her own observations. The results from this study highlighted problems in relating surface calcrete anomalies to in situ gold mineralisation.

Jan 1, 1998

The Mt. Sisa Orebody on Misima Island, P.N.G., consists of gold-silver mineralization associated with massive carbonate and amor- phous iron-manganese oxides in fractures and breccia matrix. The orebody forms the north- ern extension of the Umuna deposit. The mineralization lies within the three kilometre strike length of a northwest trending, 300 metre wide, high angle fault zone. The fault zone structure is deeply oxidi- sed, with the manganiferous oxide material resulting from oxidation of carbonate. The wallrocks are metamorphosed basement psammopelites and basic volcanic rocks, exten- sively intruded by microgranodiorite. These are dominantly epidotized and sericitized. The precious metals are associated with anomalous Cu, Zn, Pb, Mn, As, Ba, Ga, Sb, and. Mo. Many of the features of the Mt.Sisa mineralization are characteristic of volcanic- hosted epithermal deposits of western North' America. Lithologic and textural gradation is ob- served between the carbonate hydrothermal breccia-fill at Mt. Sisa, and the quartz domi- nated dilational fracture-fill mineralization which forms most of the Umuna deposit to the south. This gradational relationship is ana- logous to that within the Amethyst-OH vein system at Creede, Colorado, where it is shown to be indicative of deposition from laterally migrating fluids.

Jan 1, 1987

By Fulton B, Stewart R, Leach T

Gold mineralisation at Porgera is inferred to have been derived from a deep differentiated magmatic source which is capped by a series of (now tilted) inward dipping sills and stocks, which comprise the Porgera Intrusive Complex. An arc normal transfer structure provides a conduit, at the intersection with an arc parallel structure, into which basic magma derived from the deep melting of mantle material has been emplaced. Two phases of mineralisation display an association with late stage feldspar porphyry intrusives. Stage I carbonate-base metal-style gold mineralisation occurs as early quartz-sericite, then massive sulphide and late zoned Mn-Fe-Mg-Ca carbonate vein/breccias. Magmatic fluids derived from the deep magma source, are interpreted to have migrated along the margin of a feeder stock to the sills, and south to Waruwari. Stage II epithermal Au-Ag quartz-style gold mineralisation occurs as early fluidised breccias and carbonate veining, followed by zoned quartz-roscoelite-carbonate-gold vein/breccias, and late carbonate and/or sulphate open space infill. Magmatic fluids are interpreted to have utilised the same plumbing system as the late stage feldspar porphyry intrusive, and then migrated into the Roamane Fault which was dilated by; dextral rotation on elements of the transfer structure, normal faulting, and refraction around the competent footwall hornblende diorite. Bonanza gold is localised in a jog in the Roamane Fault, hangingwall splits and at intersections with cross structures. Bulk low grade Stage I gold has been deposited by the mixing of magmatic fluids with cool gas condensate waters, whereas high grade Stage II gold mineralisation resulted from the rapid quenching of mineralised magmatic fluids by oxygenated groundwaters.

Jan 1, 1995

The Fosterville goldfield, situated 25 km east of Bendigo, Victoria was at its peak between 1894-1910 with some 47 600 ounces produced (Figure 1). Since that time intermittent mining and tailings retreatment was undertaken until Bendigo Gold Associates delineated a viable resource and commenced an open cut heap leaching operation in early 1991. Unfortunately they encountered financial difficulties and Perseverance Exploration purchased the mine in April 1992. Perseverance operated a successful heap leach operation nearby Nagambie, 100 km east of Fosterville. Based on its acquired heap leaching experience, Perseverance Exploration was able to instigate operational changes to create a successful small gold heap leach operation. The major change was the using of the original multi-use leach pad as a single-use leach pad. The available data allows for a comparison of the two operating systems.

Jan 1, 1994

The paper will review the marked upsurge in the installation of new continuous metal coating lines, both hot dip and electrodeposition. Although some of this new capacity has been replacement for obsolete facilities or directed at traditional markets, eg building products, consumer durables etc, by far the major portion is targeted at the automotive industry. The reasons for the rapid growth of coated automobile panels are discussed. A comparison of the installed capacity with projections for this market indicate that a severe over-supply situation has arisen. Many coatings are now available for the automotive industry, each with their own strengths and weaknesses, but none as yet wholly satisfactory. Coating development has mainly been cost driven. This favours hot dipped coatings, providing surface quality and pressing problems can be overcome. The high cost per unit thickness of electrodeposited coatings has also seen pure zinc coatings being replaced by thinner, more corrosion resistant alloy coatings such as zinc-nickel and zinc-iron. Recently resin overlays have been introduced to improve the performance of electrodeposited coatings. Developments in coatings for the more traditional markets will be described. The fastest growing market in the last decade has been prepainted product for the building industry. This has led to the installation of extra painting capacity and again it appears an excess capacity situation has occurred. Over the same period the traditional zinc coatings have continued to lose market share to the zinc/aluminium alloy coatings, Galvalume and Galfan. These have been joined recently by '1'aiyo Crack-Free which has been taken up by some metal coaters. Galvalume is now widely accepted as being the best available coating for unpainted applications. It is also suggested that 'spin-off' coatings from automotive developments might find a niche in the consumer durable market. The end users of coated products, particularly the automotive industry, have demanded improvements in quality, such as surface smoothness, formability, etc. At the same time the new coating lines have to process wider strip and run at faster speeds. To reconcile these somewhat incompatible needs has required numerous process improvements, many of which need in-line instrumentation and computer control. The more important of these changes are discussed briefly. Finally the paper will describe the recent developments which have occurred in continuous galvanising in Australia and put them into context with the rest of the world.

Jan 1, 1993

By F Palkovitz, S Wilson, F Felipe

The management of waste from mining operations is a significant aspect of bringing a mineral commodity to final market. The ore beneficiation process and transport/disposal of waste involves significant consumption of costly resources. A number of options exist to dispose of mill waste on surface and as a backfill material. These range in complexity, risk, capital cost, operating cost and ultimately business performance. This paper discusses the value delivered to a business in using dewatering systems including paste as opposed to conventional slurry tailings disposals. This is illustrated through various case studies and serves to demonstrate how paste can add value and reduce risk to a successful business.

Jan 1, 2009

The selection of an appropriate mining method should take into account the geometry of the deposit and its physical properties. Other factors which assist in the determination are the requirements for flexibility in the mining process, minimisation of risk factors and maximising the financial return. Several established mining methods exist which can encompass the requirements to deliver the optimum mining method, this can be in both an underground or open cut environment. The objective is to outline these methods and where they can be applied in a mining project.

Jan 1, 1997

By Denby B, Hollands R. Schofield D

Surface mines are in operation worldwide, the vast majority employ large haul trucks for the transfer of material both to the outside world and around the site. The sheer size of these trucks and the operating conditions means there is a high

Jan 1, 1998

Having provided basic data in the main paper I would now like to move on to discuss these areas in broader terms and to examine the various coalfields in terms of their tectonic setting and depositional environment and ultimately to make some brief comments on the factors which may have controlled deposition.

Jan 1, 1975