Search Documents

By H Arvidson, J Vann

When only wide-spaced drilling is available, for example at concept, prefeasibility and feasibility stages, properly implemented linear estimation (including ordinary kriging) predicts grade tonnage relationships that are over-smoothed compared to final production estimates (and production). Non-linear estimation and conditional simulation are alternative geostatistical approaches that can provide more reliable estimates of the recoverable tonnage and grade from wide-spaced drilling. Non-linear estimation and conditional simulation have been rarely used on iron ore deposits. However, these techniques have had wide application in other commodities such as gold and base metals. Conditional simulation has been used in the iron ore industry (eg Guibal et al, 1997); however, its use here is outlined as a means of generating non-linear estimates, not just its use for variability and drill spacing analysis. As a rule, regardless of commodity, the decision to use non-linear geostatistics will necessitate increased skills and require more time. This decision must therefore be justified in terms of cost-benefit. Such cost-benefit analysis is not straightforward, and to help an approach for determining when linear estimates are inadequate is presented. Recommend in this paper is a well-established non-linear geostatistical approach, the global ædiscrete Gaussian modelÆ (DGM) of change of support, as a tool to establish whether moving from linear to non-linear estimates will materially improve estimate results. Also discussed is the additional use of DGM as a block model validation tool. One specific factor contributing to the lack of application of non-linear geostatistical methods in iron is the added difficulties that arise when conditional simulation and non-linear estimates are required to reproduce the numerous and often important correlations between variables in iron ore deposits. Consequently, presented in the paper is a synoptic review of non-linear estimation and simulation methodologies applicable to correlated variables.

Jan 1, 2007

By R O’Sullivan, D Taylor, J G. McLellan, B Miller

The Mount Isa copper deposit is located adjacent to the city of Mount Isa, Queensland, and lies within a series of Palaeoproterozoic to Mesoproterozoic Superbasins. The deposit is hosted almost entirely within the Urquhart Shale (US), a unit of the Mount Isa Group sediments and part of the Isa Superbasin. The copper mineralisation is separated into two distinct orebodies: the X41 mine (1100 and 1900 orebodies) and the Enterprise mine (3000 and 3500 orebodies). The orebodies are situated in the hanging wall of the major controlling structures, the Paroo Fault, which has juxtaposed older basement Eastern Creek Volcanics against the younger Mount Isa Group sediments cf 1655 ± 4 Ma. Conjecture remains over the exact timing of this thrust event. However, it is clear that inflections on the Paroo Fault have a close association with the orebodies and are an important structural feature in the mineralisation of the Mount Isa copper deposit.The life-of-mine is reducing steadily and new geomechanical modelling techniques were employed to target structurally controlled mineralised zones in three dimensions. Following a structural review of the mine using underground mapping, structural data and core shed observations, a conceptual 3D mine model was constructed utilising existing data modelled in MineSight®. This conceptual model included all the main lithological units and structures. The conceptual model aimed to test the effects of deformation on the main lithological and structural components of the system and attempted to highlight areas of anomalous stress and strain that may indicate a higher likelihood of fluid focusing and mineralisation potential. This project was focused on testing the latter stages of a D3 event (NE–SW compression) and D4 event (SE–NW compression), which are considered to be responsible for the current location of the mineralisation.The fully coupled 3D finite element analysis models resulted in highlighting anomalous patterns of stress and strain and subsequent fluid flow as a result of the two deformation events. The NE–SW D3 simulation provided the best correlation with the known distribution of mineralisation. This event also indicated several areas on the Paroo Fault and within the US that have potential to host further areas of mineralisation. The SE–NW D4 simulation provided less of a correlation with known mineralised zones. However, this event may have been responsible for post mineralisation re-mobilisation of copper on a relatively small scale. Areas of maximum shear strain, shear stress, volumetric strain and fluid flow correlated well with areas of minimum principal stress and provided the best overall match with known mineralised zones. Furthermore, several additional highlighted areas provide a high potential for further discovery of copper mineralisation. Recent exploration drilling north of the Enterprise mine 3000 orebody, utilising geomechanical modelling as part of the targeting criteria, intersected copper mineralisation, providing further validation of the modelling results.CITATION:McLellan, J G, O’Sullivan, R, Miller, B and Taylor, D, 2014. Geomechanical modelling of the Mount Isa copper deposit – predicting mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By J Mar·n, R Anderson, S Strohma, R Harvey

Xstrata is the operator of both Minera Alumbrera Ltd (50 per cent Xstrata, 50 per cent Wheaton River) and Ernest Henry Mining Pty Ltd, (99.99 per cent Xstrata), both copper-gold deposits, using conventional SAG/ball milling at current capacities of 36 Mt/yr and 10.3 Mt/yr respectively. Alumbrera is located in Catamarca Province, in the north west of Argentina. Ernest Henry is located in Cloncurry, north west Queensland, Australia. Both operations started in late 1997, with commercial production achieved in early 1998. Different designs and equipment are in use for both operations, however the evolution of SAG milling performance, although logically related to their specific features, reflect similar trends of consistent increases in throughput. This paper will discuss the main changes to the SAG mill liners in both operations and the results achieved to date. A summary of the operating strategies will be included.

Jan 1, 2003

By M M. Collisson

The Synthetic Rutile (SR) plant operations, North Capel, produce electrostatic precipitator (ESP) fume and kiln scrubber residue. Typically ESP contains about 18 per cent Ti, 13 per cent Fe, 0.5 per cent Mn, eight per cent Si, six per cent Al, 16 per cent C, 0.9 per cent Zn, 0.6 per cent Pb, 300 ppm As, 300 ppm Cr and 5 ppm Cd. These wastes are held in a storage dam together with neutralised acid effluent (AE) liquor. A project was initiated to treat the fume and produce a benign residue that could be delivered to landfill, reducing dam space storage. Plant AE, containing free acid (9 - 14 g/L), Fe (6 - 7 g/L) and Mn (1 g/L), was used to leach ESP. The degree of extraction achieved for various elements include about 20 per cent Zn, almost 50 per cent As, five per cent Al, 0.4 per cent Pb and 15 per cent Cd. Extraction was most effective at pH The residue from AE leaching still contained Pb. TCLP tests of the leach residue produced Pb extraction significantly higher than the 0.1 ppm stipulated by Class 2 landfill guidelines. Other elements (eg As, Cd, Cr) successfully met the limits. Further leaching of the residue with EDTA extracted up to 65 per cent of Pb content. TCLP tests on treated residue showed Pb leaching potential of Lead was removed from the leach circuit as the sulphate by acidification of EDTA leach liquor, allowing EDTA to be recycled. The study showed that one waste stream can be used to treat another and help reduce plant waste.

Jan 1, 2001

By R Morrison, R Dunn

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the æAMIRA P754-Metal Accounting and ReconciliationÆ project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called æthe propagation of errorÆ.

Jan 1, 2007

By C I. Edwards

Phosphorous is typically present in iron ore either in the mineral apatite, Ca5(PO4)3OH, or associated with the goethitic fraction of the ore. In this paper, we present results that show that phosphorous associated with the goethitic fraction can be removed with a heating pretreatment around 300 176;C for 1 h, followed by a caustic leach with 1 - 5 M NaOH, or a leach with sulfuric acid at pH 0.5. The heating pretreatment is considered to dehydroxylate the goethite to form a haematite intermediate phase, ‘protohaematite’, that reacts during the leach making the phosphorous accessible to the leachant. In the acid leach, ten to 15 per cent of the sample was dissolved to obtain a leach product with 0.08 per cent P. In the caustic leach, as no weight loss occurs, it is proposed that iron species associated with the protohaematite have either not dissolved or have reprecipitated at the high pH values of the leach.For an ore containing apatite as the source of phosphorous, a leach with sulfuric acid dissolved the apatite, lowering the phosphorous levels in the sample. The sample treated contained carbonate minerals (including siderite) that also reacted with the acid, and in practice a balance between the dissolution of the apatite and the carbonate minerals may be needed to minimise acid consumption.

Jul 11, 2011

By A Baker

Hail Creek Mine is an open cut coal operation owned by Rio Tinto. It is located 120 km south west of Mackay in the Bowen Basin region of central Queensland. Opened in late 2003, the mine produces two high quality coking coal products that are used in the production of steel in various overseas markets. Hail Creek is a dragline and truck/shovel operation with a capacity to mine eight million tonnes per annum. In 2010, the production was more than seven million tonnes.Traditionally, coal seam edge loss had been minimised on site by the practice of coal edge buffering. Importing buffer material can be quite expensive as it requires a large involvement from the truck and shovel or dozer fleet. In order to minimise this expense, a program of front splitting was introduced on site. Front splitting however involves an additional blast interaction which places added pressure on mining schedules. Both these methods of coal protection demonstrated a significant benefit with coal loss being reduced by approximately seven per cent (absolute) compared to traditional cast blasting.With the application of electronic detonators at Hail Creek the new blasting practice of dynamic buffering is able to be performed on site. Dynamic buffering refers to a blasting practice where two or three separate blasts are initiated during the same blasting event (front-split, cast and at times presplit). The process involves firing a front-split and allowing it to have time to settle and buffer the coal edge prior to the cast blast initiating. This practice is only made possible with the use of electronic detonators and the effective absence of a surface burning front. Current practice at site involves the front-split being fired (occasionally at the same time as the presplit) and the main cast blast being initiated several seconds later. Dynamic buffering is now used for all cast blasts to coal at Hail Creek. Electronic detonators have allowed Hail Creek to achieve reduced coal losses by buffering the coal edge without compromising the mining schedule.

Nov 8, 2011

By W P. Breytenbach

"The phased application of statistical process control (SPC) infers that processes are classifiable as pre-SPC (or phase zero), phase I and phase II processes, with different objectives being pursued in the different phases. Phase zero processes, defined as processes affected by assignable causes of variation, are characterised as follows: out-of-control with unknown autocorrelation structure having an unknown statistical distribution not performing consistently on target with minimum variability potentially incapable of conforming to the product specifications. The objectives of phase I SPC is to obtain estimates of the mean (µ), variance (s2), probability density function (f(X)) and the autocorrelation structure, as well as transforming the process into a phase II process (defined as a process conforming to specifications and performing on target with minimum variability). As in any other type of research or pragmatic improvement intervention, sampling is required is to achieve these objectives. The challenge of deciding a phase I sampling plan is multifarious since it has to cope with the aforementioned effects of assignable causes and provide for rigour estimates of the unknown parameters. Furthermore, deciding sampling plans in phase I invariably presents a classical catch-22 situation: appropriate sampling is required to determine the autocorrelation structure of a variable, but knowledge of the autocorrelation structure is required to formulate an appropriate sampling plan. This paper suggests, for random variables, guidelines to formulate sampling plans, and presents a methodology to estimate the inherent process parameters of process variables and an approach to identify assignable causes in phase I. CITATION:Breytenbach, W P, 2014. Rational sampling and standard deviations for random variables in phase i application of statistical process control, in Proceedings Sampling 2014, pp 141–154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A Marton

Concerns with crest losses have seen changes to a number of design and operating parameters to retain the integrity of the wall and the berms of the Kidston Gold MinesÆ Eldridge Pit. Until trials began in 1999 most final wall designs utilised large diameter blastholes up to the presplit row to achieve the wall angle. The berm crests were being lost, wall support requirements were increasing and affecting mining schedules and several fault areas were putting pit access at risk. Standard designs had been determined during the early mining years and while periodic modifications had been made there was a need for major blast pattern revision. This paper traces the development of wall control blasting programs over the years, relating designs to the geology and the evidence in the walls with the theories of the day and includes the recent trials that were conducted in what is a most unforgiving geology. Trials and improvements to ensure the walls were safe were conducted even as the mine neared its economic life. Instrumented monitoring of trials blasts has greatly increased the understanding of the damage criteria and enabled rapid revision of designs. Recent changes included reduction in presplit energy, charge redistribution and use of smaller blast holes for the trim patterns. Determination of a minimum proximity-to-final wall limit for production blastholes, establishment of the correct standoff to berm crests and walls and selective use of presplitting techniques for protecting crests have resulted in cost effectiveness, improved bench crest retention and an overall reduction in visible wall damage.

Jan 1, 2001

By D Will

RedrossThe Redross orebody averages 1 m wide, has a strike of 50 - 350 m, dips at 55° and has a basalt footwall and an ultramafic hanging wall. The most successful and innovative aspects of mining Redross were:•ore development innovations, 90 per cent of development was split fired with a shanty back profile to enable larger and more productive equipment to be used and resulted in higher development grades, improved project payback time and improved ore recovery;•hand held stoping using a multiple level, bottom up ‘V’ shaped hand held stoping method that allowed mining on multiple levels with hand held productivities between 50 and 90 tonnes per shift;•the use of 1 m cement pillars and 7 m high crown pillars were used to create multiple mining areas that enabled high overall production rates from hand held mining this orebody; and•the use of vertical cement pillars to enable hand held mining of adjacent stopes without leaving ore pillars.MarinersThe Mariners orebody averages 3 m wide, has a strike length of 50 - 250 m and dips at 50° with a basalt footwall and poor ultramafic hanging wall. The most successful innovative ideas of re-opening Mariners were:•Dewatering the existing mine workings utilising ‘oilfield’ technology by installing a long submersible pump in on existing pump rising main. This enabled the mine to be dewatered at rates up to 100l/ sec and helped overcome the 45 to 55 L/s inflows.•Overcoming the technical problems associated with Mining N07 ore blocks which had severely deteriorated from being underwater for five years by using reverse firing techniques to improve extraction rates and reduce dilution.•Mass firing a large mining block in the N08 with minimal void space because of deteriorating ground conditions.•Use of a longhole version of the Redross hand held mining method to achieve 100 per cent extraction of the N09 higher grade lenses.

Mar 21, 2011

By I M. Platten

Narrow reef gold deposits are generally less than 4 m in width and relatively complex geological phenomena. They often display variable geometry, attitude, continuity and internal architecture. Economic grades are mostly restricted to specific structural domain(s) and localised within discrete ore shoots that have a nuggety internal grade distribution. On account of the often extended history of geological events, the specific factors localising gold-rich domains are likely to be unique to a particular mine or even reef. These features lead to a high resource risk and require careful management during both evaluation and mining. The gross form, location and global continuity of gold reefs can generally be determined from surface diamond drilling leading to the definition of Inferred Mineral Resources. It is likely that for the definition of Indicated and Measured Mineral Resources underground development and/or close- spaced diamond drilling will be required. Understanding geometry and continuity permits the resource to be more effectively managed, lowering risk/uncertainty. This in turn will allow for well-informed financial and operational decisions. Most importantly, project expectations and milestones can be set at achievable levels.

Jan 1, 2008

By L Gobbo

X-ray diffraction (XRD) provides useful information about the composition of an ore sample in terms of quantification of crystalline phases and amorphous content. The use of new, fast detection systems implemented in CubiX FAST industrial diffractometers creates the opportunity to use this technique in exploration and modern process control. Besides the chemical composition of iron ores, their phase composition is also an important factor for exploration, quality control and processing. In the analysis of iron ore, XRD can identify the phases containing iron, such as haematite Fe2O3, magnetite Fe3O4, and goethite FeO(OH), and any other mineral phases present, especially silicas. Quantitative analysis is possible by various classical methods such as straight line or polynomial calibration with standards, but modern quantification analysis techniques such as Rietveld analysis or full pattern autoscale analysis are attractive alternatives, as they do not require any standards. These methods offer impressive accuracy and speed of analysis. Another analysis technique offering great benefit to ore exploration and process control is cluster analysis. This technique greatly simplifies the analysis of a large amount of data, eg from drill core samplings, and automatically sorts closely related scans of an experiment into separate clusters and marks the most representative scan of each cluster as well as outlying patterns. This can facilitate multi-dimensional compositional mapping of ore deposits, identifying regions of favourable mineral composition and allows fast and reliable tracking of the process. It is the most economic procedure to have automatic data evaluation without involving any dedicated personnel in the process. Details of the techniques used, sample optimisation methodologies, results, data precision and limitations will be discussed. The approaches have enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron ore materials in an industrial environment.

Jan 1, 2009

By A B. Bayooke, A C. Robertson

In terms of underground tunnelling in metres advance per capita, Australasia compares well with the best world performers. This is because of the large number of metalliferous mines, coalmines and civil tunnelling projects, with the Australian tunnel advance for civil and mining projects exceeding 625?km/a. In terms of hard rock quarry extraction, Australia produces approximately 200?Mt/a of aggregates, roadbase, fill material and specialist rock products from its quarries, which equates to approximately 8?t/capita. Australian mining and tunnelling contractors are also of world standard and are used to excavating in a variable range of ground conditions in a competitive environment. One author has been involved in tunnel and underground space planning and quarrying in Australia for the past 25 years and predicts that, over the next 20 years, there will be a major swing towards underground space for commercial uses. This paper identifies the potential uses of underground commercial excavation and the planning and geotechnical challenges for the future. Underground quarrying creates new opportunities to extend existing quarries within their urban footprint with minimum impact on the surrounding community. Investigations by the authors reveal that there are very few cities in the world that actually incorporate underground space planning in their city plans. However, cities such as Helsinki have been planned in detail to utilise the rock resources beneath them. Brisbane is used as a case study for a practical application of commercial underground space and underground quarrying in Australia.CITATION:Bayooke, A B and Robertson, A C, 2014. Geotechnical challenges for underground commercial space and quarrying in Australia, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 317–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J E. Everett

An essential requirement of product quality control in the mining industry is to be able to reliably predict key quality properties of finished product from the data available before the extraction of the ore. From a production viewpoint, the unit of data collection is generally the input and output data set for each shift of crusher production, but could be any period where mine precrusher data can be reliably matched with product data.This paper demonstrates that linear regression models can be used to predict crush grades from blast grades, even where the crush material is blended from multiple sources or pits for each of which differing regression models might apply. The advantage of using increasingly complex regressions models to match the available data to give increasingly more powerful models is examined. The best model for any application will be a balance between required predictability, available data and the business’ tolerance for complex models.The regression modelling approach has several advantages over the more classic method of run-of-mine (ROM) crusher trials, which will be discussed.The models can use any predictor variable such as grade, geotype and in situ density provided the preextraction data set can be reliably matched with post-crusher data and is significant as a predictor. The models have been used extensively in the generation of the daily crusher plan with the aim of maintaining finished product grade. This approach has also been used associated with exploration drilling and long-term planning.It is acknowledged that there are inherent problems in fitting lump and fines grade to a linear model. However, these problems are minor when they are used for interpolation within the window spanned by the shift blend records used to produce the model. This paper discusses some of the issues limiting linear regression models in this application, and suggests methods enabling consistent models to be formulated

Sep 5, 2011

By C J. Carr

The Ernest Henry Mine (EHM) is owned and operated by Xstrata Copper and is located in North-West Queensland, Australia. The mine is currently undergoing a transition from an 11 Mtpa open pit mine to a large sublevel cave underground mine producing 6 Mtpa. Due to a number of factors, including geometry of the pit and crusher depth, the decision has been taken to develop a hoisting shaft rather than inclined conveyors.During the feasibility study the strip and line shaft sinking methodology was preferred over blind sinking due to scheduling opportunities and interactions with level development. Other methods of sinking considered included large-diameter raise boring, which was rejected due to concerns relating to centreline accuracy. The strip and line decision was reviewed during the tender process where better than anticipated blind sink advance rates and costs were presented. This in turn enabled the higher cost of the blind sinking method to be justified by a combination of reduced risks including schedule and ground water management. This paper discusses the pros and cons of both strip and line and blind sinking methodologies in the Ernest Henry context including sinking rates and total schedule impacts of the two methods, the key risks associated with each method, cost implications of blind sinking and safety implications of the work methods in general. The paper then concludes with the reasoning behind the decision to change to blind sinking for the EHM shaft.

Mar 21, 2011

Central to any business is its Asset Management Plan which encapsulates the business context and key organisational objectives such as profitability, safety and environmental standards. Life Cycle Planning (LCP) is a key component of an overall Asset Management Plan. A comprehensive approach to Life Cycle Planning forecasts the financial expenditure required to support the performance of the asset over the business life. It incorporates capital, maintenance and operational expenditure along with an estimation of economic life. Within its body the LCP provides the detail of the maintenance plan and method of its execution. Once optimised the LCP becomes the overarching plan executed through the application of several elements of the Asset Management Plan to ensure the return on investment from the assets is optimal. Each of the elements of the LCP is bound by a set of loops that provide information based on the analysis of outcomes. These loops drive the continuous improvement of performance and cost over the life of the asset. In this way we ensure that the LCP is a dynamic plan responsive to the changing business environment. The paper being presented today will describe the process undertaken and the outcomes derived when this approach was applied to a $600 M+ coal handling and preparation plant in QueenslandÆs Bowen Basin. It will also delve into the difficulties encountered from both technical and cultural aspects; the latter proving to be the most difficult to manage. It will describe the hurdles and barriers that hampered progress including the human influences and the natural desire to revert to what has been done in the past when things became a bit difficult. In the end the results are there to show that the upfront expenditure and investment in time was time and money well spent and the outcome has the operation well placed to manage the assets in a manner designed to deliver the optimal business outcome.

Jan 1, 2007

By W Newns

This paper describes laboratory and in situ tests and determines a set of parameters for stiffness and strength properties for a weak sedimentary rock mass, the East Coast Bays Formation of Auckland. The parameters derived are discussed in relation to peak strength and in respect of deformation limits associated with sequential excavate and support (SEM) or conventional tunnelling.

Mar 8, 2011

By B Stump

Reliable particle size analysis in minerals processing plants is a critical factor to the economic return of a plant. As recovery of valuable minerals is compromised for particles outside the optimal size range, effective and reliable particle size analysis is more crucial than ever, particularly in the current upswing of the global commodities market. Inefficient particle size analysis can lead to excessive over-grinding, thereby significantly increasing energy consumption and reagent costs, whilst negatively affecting process operation, thickening capacity, water recovery and tailings disposal.Australia’s first installation of a particle size analyser in Iron Ore has been monitored with great interest by the industry. Previously, manual size sampling at Rio Tinto’s Paraburdoo fines processing plant involved off-site sample analysis, with a turnaround measured in days. The Outotec PSI® 500 particle size indicator, commissioned in July 2009, takes approximately three minutes per line at site.The paper will include details on the following:• plant description,• sampling design,• PSI® 500 analyser functionality description, and• key learnings from site.

Jul 11, 2011