Search Documents

By C. E. Coleman, D. Hardie, A. E. Wraith

A photoguaplric method of measuring crack velocities has been applied to an examilzation of- the effect of hydrogen on the impact properties of zirconium. Results indicate that the crack in hydrided zirconit travels at about 26 m per sec whereas that in the uacuum -annealed is dependent on the speed of the hammer. RECENT work on the effect of hydrogen on zirconium reveals that when hydrided zirconium is tested in slow bending the crack producing failure can be unstable. The mode of fracture seems to involve the crack linking up broken hydrides by a ductile mechanism in the zirconium matrix.2" In order to compare the fracture of zirconium with that of other metals which show unstable crack propagation, notably steel, the rate of the crack spread must be known. As the methods previously used for measuring crack growth are either unsuitable for the present work5-'' or very costly," a simple technique has been devised in which the maximum crack velocity is derived from a series of crack position-time measurements. EXPERIMENTAL PROCEDURE The experimental arrangement is shown schematically in Fig. 1. The flash unit12 was triggered when the Charpy hammer touched the specimen and the 6-psec flash of the lamp delayed by a preselected time interval in the range 100psec to 10 msec. The camera was left on open shutter during the test. From direct measurement on a calibrated photographic print, Fig. 2, the position of the crack and the specimen was found at a known time after impact and, from a series of such tests using an appropriate range of flash-delay times, the crack velocity was estimated. Preliminary experiments were carried out on mild steel above and below its transition temperature. Vacuum-annealed zirconium, and zirconium hydrided to 100 ppm H were then tested at 20" and 150°C. For comparison, Zr-2.6 pct Nb alloy (in the 0 + transformed /3 condition), vacuum-annealed or hydrided to 100 ppm H, was tested at 20 C. The chemical analyses of these materials are given in Table I. For the high-temperature tests a fine chromel-alumel thermocouple was spot-welded onto each specimen close to the notch. The test piece was heated up to 200°C to allow enough time for preparing the apparatus while the specimen cooled to the testing tem- perature. It was assumed that the specimen cooled uniformly. The accuracy of the flash-delay time was better than i2 pct i 5 psec. The crack length was taken as its maximum distance traveled normal to the length axis of the specimen. Errors in these measurements arise as a result of the uncertainty in the location of the crack tip and the difficulty in defining the exact position of the crack starting point. The latter was due to the bonding and large amounts of deformation at the hammer contact point, especially in the vacuum-annealed specimens tested at 150°C. The maximum error in the measurements was however estimated to be about 5 pct. DISCUSSION OF RESULTS From the trial experiments using mild steel above its transition temperature it can be seen from the plot of crack length against time after impact, Fig. 3. that a reasonable estimate of the maximum crack velocity at the surface of the specimen may be made. Other features of note are the initiation time before the crack is first seen and the slowing down period

Jan 1, 1967

By C. R. Wohrman

A MELT of pure electrolytic iron with about 0.4 per cent. sulfur and 7 per cent. manganese was prepared in connection with a study of inclusions in iron. The alloy darkened rapidly when etched with a 10 per cent. alcoholic solution of nitric acid, and microscopic examination revealed the presence of a semimartensitic, semi-Widmanstättian structure (Figs. 1 and 2) closely resembling the structures found by Benedicks in his artificially prepared "meteoric iron." 1 The structures found by Benedicks were readily explained by the presence in his alloy of the two well known iron-nickel solid solutions, taenite and kamacite, and of their eutectoid (?) aggregate, plessite. By analogy, one would infer the existence of similar phases in the iron-manganese alloy just described, such as inference being strengthened by the similarity displayed in many ways by nickel and manganese in their effects on iron. IRON-MANGANESE ALLOTS ARE REGARDED AS HOMOGENEOUS Heterogeneity of iron-manganese alloys has not been recognized heretofore, judging from the data of standard metallographic books and those of original papers. In fact, iron and manganese are quite generally regarded as completely miscible in the solid state. Dr. Rosenhain,2 for example, writes: Alloys of group (a), of which those of gold-silver, iron-manganese, and copper-nickel are examples, when allowed to crystallize sufficiently slowly to attain their condition of final equilibrium, present a microstructure exactly similar to that of a pure metal-the homogeneous character of the molten solution is in that case so completely maintained that the microscope cannot detect the presence of any second constituent.

Jan 1, 1927

By Elmer W. Pehrson

NINETEEN FORTY-SIX was an eventful year for the mineral industries. Perhaps the most significant development was the socialization of industry in Great Britain, initiated in 1945 but carried to fruition in the coal industry in 1946. On Jan. 1, 1947, management of the coal industry will be vested in a National Coal Board, responsible to the Ministry of Fuel and Power. A sum of £164,660,000 has been provided to compensate private owners for assets transferred to the Board. The British coal industry has been a problem for many years. Production has declined to a point where serious shortages of fuel for domestic needs have developed. Exports have dwindled to a small fraction of the previous trade. Costs have increased greatly, and quality has deteriorated. The industry's physical plant has not kept pace with the rapidly mounting wage scales in recent years. Some claim that the best and most accessible coal reserves of Britain are heavily depleted. The industry has been harassed by difficult labor problems, including bad morale among the workers and a shrinking labor force.

Jan 1, 1947

By AIME AIME

DOUBT in anyone's mind that this is the age of metals, industrially speaking, could easily have been dispelled by attending the National Metal Congress in Chicago, Sept. 22 to 26. Iron, copper and aluminum; zinc, lead and nickel, often alloyed with each other or with some of a dozen minor metals, make the materials without which the modern world could not run. Science, pure and applied, is doing marvels in finding new mixtures, new alloys to meet new needs; in developing new means of rolling, fabricating, casting and welding metals cheaply-and effectively. These and related matters were the subject of 100 papers presented at 33 seperate sessions of the organizations that participated in the congress.

Jan 1, 1930

By AIME

DURING the happy and peaceful years between the Treaty of Versailles and the third New Deal, metallurgy became one of the most cosmopolitan of the sciences. Any metallurgist can name some twenty or thirty scientists whose work, in this country, in England, in Germany, or in France, Sweden, Italy, or Japan was as well known in other parts of the metal-producing and metal using world as it was locally, despite the fact that many of these men never left their native land. One of these metallurgical cosmopolites is Augustus Braun Kinzel, former Chairman of the Iron and Steel Division, A.I.M.E., and now a Director of the Institute. Gus Kinzel, however, is not only a cosmopolite by reputation; he is also a cosmopolite in fact. For many years he commuted at least twice a year between New York and the rest of the world; he is, therefore, not only an expert on the art and science of metallurgy but is equally expert in world travel and can expound with authority on the comparative quality and especially on the cuisine of the great prewar steamship lines; and being a true cosmopolite, he knows, as well as he knows the iron-chromium diagram, the best vintage years in the Gironde, Cote d'Or, and Saone-et-Loire departments in France and along the banks of the Moselle and Rhine in Germany.

Jan 1, 1946

J. J. MCLELLAN, Webb City, Mo.-The Media mill, at the time it was built, was the largest mill that had been designed in the Joplin district. It was put up in a hurry, to take advantage of the high prices for zinc ore in 1915, by the owners of an adjacent plant, which had been very profitable. They owned a compound Corliss engine, and to take advantage of a single-unit drive it was necessary to build the mill in the form chosen, which involved making the hopper feed directly through the breakers and rolls, the undersize from the screen passing at once to the jigs, the oversize going through the rolls and returning to the original trommels. The mill was built in fairly good proportion; crushing was done by jaw breakers, Webb City pattern,' and three sets of 42-in. (106.7-cm.) Cornish rolls for reducing the oversize. The jigs were larger than the usual practice. The roughers were two six-cell jigs, with 42 by 48-in. cells. The cleaner jig was the largest ever constructed in the district up to that time, having seven 36 by 48-in. cells, for treating the rougher jigs. There was also a chat rougher. "Smittem," as used in our district, is the partly concentrated product from the rougher, which is finished on the cleaner jigs. "Chats" are the middlings proper, that is, they are the grains of chert with included particles of sulphide; the very low-grade smittem is sometimes included among the chats. When drawing chats from a jig, we also draw about ten times greater quantity of barren chert in order to insure complete recovery of mineral. This mixture of middlings and tailings is taken to a set of 30-in. rolls, the crushed product then going to a chat rougher, a comparatively small jig, with 26 by 36-in. cells. The principal departure of the Media mill from the usual practice was to build a hopper sufficiently high to give gravity feed to the jigs, without using elevators. The sludge plant, for table treatment of sand and slime, also contained several innovations in the manner of distributing the feed. The tables were arranged in two rows and the feed ran around the outside in a launder having two or three cone classifiers

Jan 1, 1918

US 4,192,852-Precipitation of iron values as a jarosite from a sulfate solution obtained as a byproduct in the hydrometallurgical processing of zinc sulfide ore The solution is cooled, partially neutralized, and clarified. The clarified solution is heated to a temperature of 80 to 100°C in the presence of sodium, potassium, or ammonium ions to precipitate substantially all of the ferric iron as jarosite The precipitate is thickened, filtered, and washed The residual solution may be processed for zinc or other nonferrous metal values R V. Pammenter and C J Haigh, assigned to Electrolytic Zinc Co of Australasia Ltd. Mar. 11, 1980. 16 pp. (423-42) Filed: 5-8-78 (903,524). Priority- Australia, 5-9-77 (PD0030) (Drawings below.)

Jan 1, 1982

Jan 1, 1916

By S. A. Swensrud

NINETEEN Thirty-Six was the biggest year in volume in the history of the oil industry, and unquestionably the best since 1929 in respect to profits. The quota of new and difficult problems to face seemed a little smaller during 1936 than in most recent years, and a somewhat better balance existed between the different branches of the industry. 'Domestic consumption of gasoline in 1936, estimated at about 475 million barrels-the highest on record, was approximately 11 per cent above 1935, and 26 per cent above 1929. Demand for crude oil increased in about the same proportion: over 1935, and the average production, of about three million barrels daily,' constituted a new high level.

Jan 1, 1937

CHARLES KIRCHHOFF, Chairman. ALBERT SAUVEUR, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, J. Esrey Johnson, Jr., Felix A. Vogel, William H. Blauvelt, William Kelly, Leonard Waldo, James Gayley, . Richard Moldenke, William R. Walker, Henry D. Hibbard, Joseph W. Richards, - William R. Webster. Henry 1%1. Howe, E. Gybbon Spilsbury, Frederick W. Wood. Robert W. Hunt, A. A. Stevenson, The Board of Directors of the Institute has authorized the holding of a meeting under the auspices of the Iron and, Steel Committee in New York City, October 16 and 17, 1913. Gratifying responses have been received to the request of the Committee for contributions, the following papers being already assured: 1. H. M. Howe, Equilibrium Temperature for A, in Carbon Steel. 2. H. M. Howe, The Divorcing of the Eutectoid in Meteorites. 3. H. M. Howe and A. G. Levy, Determination Of the Position of Ae3, in Carbon-Iron Alloys. 4. G. .K Burgess, J. J. Crowe and H. S. Rawdon, Thermal and Microscopical Examination of Professor Howe's Standard Commercial Steels. 5. H. Dl. Hove, Discussion of the Existing Data as to the Position of Ae3,. 6. J. H. Hall, Shock Tests of Cast Steel. 7. H. F. Miller, Jr., The Design of Regenerators for Open-Hearth Furnaces. 8. E. Stütz, Paper on the "Scoria Process." 9. Albert Sauveur, Mayari Steel. 10. Felix A. Vogel, Briquetting. 11. J. E. Johnson, Jr., Paper on " Cast Iron."

Jan 6, 1913

By T. S. Lundy, J. Askill

J. Askill and T. S. Lundy (Oak Ridge National Laboratory)—Moore has proposed a simple correlation between the activation energy for solute diffusion in fee metals and the atomic volume of the diffusing species using both tracer and chemical-diffusion data. The first point we wish to make is that it is wrong to attempt such correlations without separating the two types of data. Activation energies obtained using tracer techniques cannot, in general, be directly compared with those obtained from chemical-diffusion experiments. A knowledge of the variations of chemical potentials with composition is necessary and chemical-diffusion data must be corrected for such variations, even for dilute alloys, before a comparison is possible. Secondly, for nickel, iron, aluminum, and lead, Moore neglected a number of recently published works, e.g., Al26 and Mn54 in aluminum,46 cr51 in nickel,47 and Fe55 in iron.48 These and others should have been used. If one considers only the tracer diffusion data, there is left no simple correlation of the type proposed by Moore. For example, in the case of solute diffusion in aluminum the only reliable tracer data listed by Moore are for zinc and aluminum. The nickel, cobalt, and iron data of Agarwala49 are representative of near-surface diffusion-not bulk diffusion. In conclusion we suggest that for tracer diffusion data in these fee metals there is no justification for proposing any simple correlation of activation energy with atomic volume using the limited data that are presently available. R. H. Moore (author's reply)—The writer has proposed a simple correlation which is useful in estimating the internal consistency of diffusion data. The accuracy of the correlation is, of course, a function of the number of data available. Lundy and Askill take issue with the writer's decision to include data for the systems: nickel, iron, aluminum, and lead, taking the view that the data are insufficient to establish the correlation. The writer agrees that the data are insufficient and has cau- tioned the reader that the correlation is tentative in these instances. Inclusion of these systems is justified by the interesting trends the correlation reveals. For example, the distinction between interstitial and substitutional diffusion may be clearly established, Figs. 4 and 6, and the behavior of transition elements and nontransition elements is indicated to parallel the behavior illustrated by the silver and copper systems. Lundy and Askill have singled out the aluminum system for special criticism. The writer chose to discuss the data for diffusion of iron, nickel, and cobalt in aluminum in the terms used by the original authors9 and has included the comments of Balluffi.l0 The writer did not intend the reader to conclude that data for these elements should correlate with data for the nontransition elements as Lundy and Askill have evidently assumed. Iron, nickel, and cobalt form intermetallic compounds with aluminum, so the activity coefficients of these elements may be expected to deviate markedly from unity. This may account for the low frequency factors observed by Hirano.9 The nontransition elements, on the other hand, yield relatively simple phase diagrams with no evidence for intermetallic compound formation as in the case of iron, nickel, and cobalt. In dilute solution, Henry's law should be closely obeyed, the activity coefficients should not deviate markedly from unity, and the effect on the activation energy should not be large. The accuracy of the correlation applied to these systems will improve as the data is extended. It does not seem unreasonable to conclude that its extension should be encouraged.

Jan 1, 1965

By F. W. Clark

At the present time, when lixiviation versus amalgamation is being so thoroughly discussed by practical men, and published information is so meagre, the following tests, made by students in the mining laboratory of the Massachusetts Institute of Technology, may be of interest to others. The ore experimented upon was obtained from the Sombrerete mines near Zacatecas, Mexico. A careful analysis of the dried sample resulted as follows : Per cent. SiO2,............62.79 S.............13.86 Al2O3............4.39 Fe,............11.26 Zn,............1.57 CaO.............2.91 MgO,........... 0.06 Cu,.............0.12 Pb,.............0.40 Sb and As,..........trace CO2,............2.35 Ag,.............0.16 99.87

Jan 1, 1886

By W. P. Sykes

ThiS investigation was undertaken primarily to establish the relations existing between temperature and mechanical properties in molybdenum, nickel, and an aluminum-copper alloy. Mlolybdenutn (m.p. 2500" C.) was chosen because it is partly similar to tungsten and partly similar to the common ductile metals. Also it is known to furnish, by proper treatment, a desirable material to use in studying relation of grain size and physical properties. The molybdenum used was of the quality that is drawn into wire 0.003 in. in diameter for use as filament supports in incandescent lamps; Chemical analysis shows less than 0.1 per cent. of impurities. Nickel belongs to the same class as iron. Its melting point is 1450" C. and an allotropic change at about 370" C. results in a loss of magnetism above that temperature. This feature made nickel doubly valuable for the purposes of these tests. The nickel used was obtained from the Driver-Harris Co. as 0.090 in. (2.3-mm.) wire, annealed; analysis showed 99.8 per cent. nickel and 0.150 per ccnt. iron. Aluminum is one of the low melting-point metals. Some tensile tests at clevated temperatures have been reported by Bengough but the possibility of learning more with the low temperature and sensitive apparatus available rccommendcd this metal. The samples marked A1 arc an aluminum-copper alloy that contains 3 per cent. copper, 0.42 per cent. iron, and 0.21 per cent. silicon. The presence of the copper somewhat coniplicates the analysis of the results; but the action of copper in aluminum has been studied so that its influence might have been foretold, in part at least. The material and analyses were furnished by the Aluminum Castings Co. The nickel wire, which was deformed at 400" C., was drawn under a bath of molten lead and through a die, which also was immersed in the bath. A thermocouple was suspended in the molten metal to indicate the temperature. Hot oil was uscd as the heating bath for drawing the

Jan 1, 1921

Coal production during 1963 amounted to 446 mil- lion tons, an anticipated increase of about 6% over the 1962 production of 422 million tons. Electric consumption was 207 million tons, a continuation of its upward trend with an increase of about 7%. The metallurgical market consumed 77 million tons: the industrial market, 96 million tons; and the retail market, 26 million tons. Exports were 46 million tons. Modernization continues in the coal industry as it approaches the mid-1960's. The industry has shown a keen desire to explore and pursue new developments, new concepts and new managerial methods and techniques that have become so vital and important for industrial well-being.

Jan 2, 1964

By AIME AIME

STRIP coal mining in the United States has-become noted for its massive equipment, especially its power shovels. Notable among the latest examples of this trend is the Bobolink mine of the Binkley Mining Co., at Seeleyville, Ind.,. eight miles from Terre Haute. This is only one of the Binkley company's operating properties; in all, the company owns or controls 26 mines, in fourteen seams. The Bobolink, however, is the largest strip mine in America and probably also in the world. It has an estimated life of fifteen years. The shovel used to strip the over¬burden is electrically operated, of Bucyrus-Erie make, and was. shipped to the property for assembling, a job

Jan 1, 1936

The one hundred and twentieth meeting of the Institute was held at Chicago, Sept. 22 to 26, inclusive, and was in every way success although the steel strike against the United States Steel Corpn. prevented many engineers from attending the steel session and made necessary the annulment of the trip to the steel works at Gary on Tuesday. All of the meetings were held at the Congress Hotel, with the excep-tion of the session on Non-ferrous Metallurgy which was held at the Coliseum where the Fifth National Exposition of Chemical Industries was in progress. This session was a joint one with the American Electro-chemical Society. The total attendance, as shown by the registration, was 850.

Jan 11, 1919

By Charles Bohdanowicz

As in preceding years, the most intensive drilling activity during 1934 took place in the old fields of the western part of the Polish Carpathian petroleum province (district of Jaslo). The number of wells completed to the end of 1934, expressed in percentages, is as follows: Jaslo district, 57 per cent; oil fields outside Boryslaw-Tustanowice-Mraznica, 27; Stanislawow district 8 and Boryslaw fields only 7 per cent. The number of meters drilled (Table 2), expressed in percentages, for the same fields are as follows: Jaslo district, 51 per cent; oil fields outside Boryslaw-Tustanowice-Mraznica, 26; Stanislawow district, 12, and Boryslaw oil fields, 11 per cent. This comparison shows that most of the new

Jan 1, 1935

The Board of Directors, at its meeting on March 22, 1918, extended an invitation to the American .Institute of Metals to become the Institute of Metals Division of-the American Institute of Mining Engineers in accordance with the terms of By-Law VII. This invitation was presented to the membership of the American Institute of Metals for letter ballot, and, at the meeting of the Board of Directors of the American Institute of Mining Engineers on April 26 191 ,it-was reported that the replies had been in favor of accepting the invitation. The American Institute of Metals therefore becomes a division of this Institute and the members thereof are entitled-to all privileges of regular

Jan 6, 1918

Organization Place Date 1918 Institute of Metals Division, A. I. M. E Milwaukee, Wis. Oct. 8-11 Iron and Steel Members, A. I. M. E Milwaukee, Wis. Oct. 8-10 American Foundrymen's Association Milwaukee, Wis. Oct. 7-12 American Museum of Safety and Sanitation, Exposi- tion St. Louis, Mo. Oct. -7-12 National Safety Council St. Louis, Mo. Oct. 14-17 Business Show : New York, N. Y. Oct. 21-26 National Society of Naval Architects New. York, N. Y. Nov. 14-15 American Society of Mechanical Engineers New York, N. Y. Dec. 3-6 Geological Society of America Boston, Mass. Dec. 25-31 American Association for the Advancement of Science Boston, Mass. Dec. 27-Jan. 2. 1919

Jan 10, 1918

By John R. Freeman

The die pressing of brass may be described as a method of producing irregularly shaped parts of brass and other copper alloys by hot deformation in a die under pressure. Die pressing of brass was first developed as an improvement on sand castings in order to obtain irregularly shaped articles of brass with superior surfaces, a closer tolerance in dimensions, a denser structure, freedom from porosity and elimination of the relatively large amount of scrap invariably attached to sand castings. The freedom from sandy surfaces with consequent greater tool life in machining operations was also recognized as well as elimination of losses due to the uncovering of blowholes in machining operations. Die pressing also gave alloys of superior strength. Die pressings today are made from extruded rod or shapes, according to design of the part to be made. The greater number of pressings are made from round rod, because of its relatively lower cost and ease of handling. The rod is first sheared or sawed into desired lengths, the diameter of rod used and length of "slug" or "rivet" depending upon ultimate weight and shape of the die-pressed part to be made and design of die. The dimensions of the slug are figured so as to give the minimum amount of scrap to be sheared from the pressing as it comes from the die. Extruded shapes having I, T or X sections are often used when the finished part is to have a similar shape or heavy sections are joined by relatively light sections of considerable length. A rod bent in the shape of a U is also used on occasion, for similar reasons. Proper shearing of the slugs is of considerable importance. The sheared ends of the slugs should be as flat and straight as possible. Improperly sheared ends having an angle to the axis of the bar or a rough, uneven surface are liable to give folds or laps in the finished pressing and proportionately high rejections. The property of shearing varies considerably with different alloys and should be considered in the selection of a material for a given part. Where satisfactory shearing is not possible, the slugs may be cut from the bar by power saws. Extruded

Jan 1, 1931