Search Documents

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957

By Ralph E. Davis, Lyon F. Terry

The rapid expansion of the natural gas industry in this country during the past three or four years has necessitated the construction of a number of long and comparatively large diameter high-pressure pipe lines This period of expansion and construction is still at high tide, and the current year will doubtless surpass all prior years in mileage and capacity of gas line installation. The fundamental economics of the business of long-distsrier transportation of natural gas may be briefly and simply stated, although most careful consideration must be given the actual determination and integration of the several more important factors which determine the ultimate success or failure of such a project. Reduced to its simplest form, a sound natural gas transportation project requires: 1. A competent source of gas, where the combination of quantity of gas available, cost of production, and longevity meet the given requirements. 2. A market, reasonably certain to endure in the face of any probable competition, of satisfactory size and price, and having a sufficiently favorable load factor. 3. A cost of installation of pipe line systen and an operating cost such as will, with honest and reasonably efficient management, afford a net operating return sufficient to attract the necessary capital required. In a11 new projects of this kind it is necessary that thehe three cssentials to ultimate success be assured. Hence the necessity of competent surveys of gas supply, and of market, both industrial and domestic. The prudent engineer will allow for "factors of safety" in reaching his conclusions just as he would in the design of a bridge. This paper deals primarily with but one of the major considerations enumerated above, I. e, the economic design of the pipe line system. The "pipe line system" will be considered to include (1) the pipe Iine, and (2) a series of compressor plants along the pipe line for maintaining

Jan 1, 1929

By H. M. Howe, E. C. Groesbeck

That the quiescence of a liquid while it is solidifying should favor the formation of columnar crystals, normal of the cooling surface, is seen readily on considering the mechanism of solidification. First, each particle of any composite liquid, whether it be an aqueous solution or a molten metal, in solidifying splits up into two parts, different in composition and hence in fusibility. One part is infusible at the existing temperature, and hence solidifies, and in general attaches itself to the inclosing walls of metal which have already solidified; A, Fig. 1. The other part is fusible at the existing temperature and hence remains molten. In the case of carbon steel, the part of each drop which actually solidifies is poorer in carbon than the drop itself was before it began to solidify, and this impoverishment of the solidifying half-drop enriches the other half-drop in carbon, and thus makes it unfreezable at the existing tern- By this mechanism there arises during solidification a "littoral" or shore layer of liquid B, Fig. 1, bathing the already solidified walls, and more fusible than either those walls or the great remaining central mass of liquid or " deep sea " C, from which it separates them. It is essential that we grasp clearly this conception of a fusible littoral molten layer coating the already solidified walls and separating them from the deep sea. Meanwhile heat is flowing rapidly outward through these walls, its escape cooling them, so that if any given particle of the deep sea metal could get past this littoral layer and come into contact with the solid walls, it would in turn solidify, and like its predecessors would split up in solidifying into a less fusible half-drop which would attach itself to those . walls and a more fusible one which would remain molten. Thus we see

Jan 1, 1920

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin: The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most promising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestetn Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1947

By Charles W. Sweetwood

THE Western phosphate field, virtually ignored for 40 years, has been undergoing a rapid climb to economic importance. Until World War II there seemed to be no reason for developing the phosphate rock region of the Intermountain Empire. But the tremendously increased demand for food production and the needs of many branches of the chemical industry changed all that. Quite suddenly a report made by the U. S. Geological Survey at the turn of the century became important. The survey showed that 60 pet of the nation's phosphate reserves were in the western phosphate field. Simplot Fertilizer Co. was one of the first to become actively interested in the development of the area. In August, 1945 the company began exploration of the Phosphoria Formation on the Fort Hall Indian Reservation. The result was the Gay Mine, about 18 miles east of Indian Agency Headquarters at Fort Hall, Idaho, developed to supply high grade phosphate rock for processing into superphosphate fertilizer at the company's Pocatello plant. Six ft of high grade oolitic phosphate rock (ranging from 32.5 to 34.5 pet P2O5) were discovered at the base of the Phosphoria Formation by diamond drilling and dozer trenching. High quality and thickness, plus the fact that the formation lay flat and near the surface made strip and open pit mining possible. In one year of mining, starting June 1946, a total of 53,000 tons of main bed oolitic phosphate rock was hauled to Pocatello for processing into supersulphate. The first year's operation was in

Jan 1, 1952

By B. C. Wonsiewicz, W. W. Wilkening

Following a procedure proposed by Wheeler and Ireland, Plane stress yield loci were constructed from Knoob hardness numbers. Basically, six differently oriented hardness measurements were made on three orthogml surfaces through pure poly crystalline magnesium sheet, a magnesium single crystal, and sheet of the magnesium alloys: Mg + 0.5 pct Th, Mg + 4 pct Li, AZ31B, and EKOO. Hardness loci were found to be in poor agreement at small strains (E < 0.05) with loci established by a more rigorous technique. At larger strains (E - 0.10) the agreement is fair, but at this stage in deformation the conventional locus has lost much of the asymmetry that characterizes these anisotropic materials. Two effects which will lead to distortions in the Khn locus are discussed with reference to the geometry of plastic flow during a hardness test. DETERMINING a material&apos;s resistance to multiaxial loading is of interest not only from a structural design viewpoint but also from that of deformation processing. Unfortunately, the determination of the yield locus, although simple in principle, involves tedious procedures if the results are to be at all rigorous.&apos; The idea, first proposed by Wheeler and 1reland2 of determining the yield locus by means of six Knoop hardness impressions along the principal directions in a material has obvious appeal. It is simple, quick, and should be applicable to very thin sheets. If such a technique could be demonstrated to produce consistently reliable results, it would be of interest to both researcher and designer. Lee, Jabara, and ackofen have compared the yield locus determined by Knoop hardness measurements (the Khn locus) to a locus determined by more rigorous techniques. They found good agreement for two titanium alloys at a plastic strain of about 1 pct. The purpose of this paper is to investigate if the Khn locus construction is a reasonable approximation to the locus of a highly anisotropic material. Examples of such materials are magnesium and magnesium alloys which have severely distorted yield loci which in turn reflect markedly dfferent yield strength in different directions.&apos; In pure magnesium, for example, the yield stress in tension along the transverse direction may be four times the yield stress in compression in the same direction and twice the tensile yield stress in the rolling direction. Predicting such large differences ought to serve as a severe test of the Khn locus construction. EXPERIMENTAL PROCEDURES Samples of rolled sheet, 0.250 in. (6.35 mm) thick, of pure magnesium and four magnesium alloys (Mg experimental materials. The pure magnesium together with the lithium and thorium alloys were those used in the study of Kelley and Hosford. The grain size was ASTM number 4 for the pure magnesium and number 6 for the alloys. HARDNESS TESTING The materials were sectioned along the rolling and transverse planes, mounted in a quick setting resin, and mechanically polished. Most of the hardness tests were performed on a surface prepared by electro-polishing (30 pct nitric acid in methanol at 0°C and 20 v) with the exception of the AZ31B and EK00 alloys which were made directly on a metallographically polished surface. However, subsequent hardness tests on the same sample after heavily electropolishing, revealed essentially the same hardness as before. At least twenty Knoop hardness impressions under a 100-g load were made in each of the six orientations shown in Fig. 1. The average hardness number and standard deviation were then calculated for each orientation. CONVENTIONAL LOCUS CONSTRUCTION Yield loci were constructed using a technique described in detail by Lee and ackofen,&apos; in which the flow stress (stress at a given plastic strain) fixes the coordinates of a point on the locus and measurements of the strain ratio serve to establish the slope of the locus at that point. The loading paths which correspond to uniaxial tension or compression tests establish the four intercepts of the locus with the coordinate axes plus one point on the balanced biaxial tension line Tensile testing was performed along the rolling and transverse (r, t) directions. Samples had a uniform rectangular gage length 1 by 4 by 4 in. (25.4 by 6.35 by 6.35 mm) and were deformed at a strain rate of 3.33 x 104 sec-&apos;. The tests were interrupted periodically to unload the sample and measure the plastic strains by means of X-Y post yield strain gages. Compression tests in the rolling, transverse, and through-thickness (r, f, z) directions were performed on 1/4 in. (6.35 mm) cubes at an initial strain rate of 8.33 x sec-&apos;. Lubrication was provided by 0.002 in. (51 pm) Teflon sheet which was renewed after unloading for micrometer measurements used to calculate the strains.

Jan 1, 1970

JULY was a month of great turmoil, both economic and political, in many parts of the world. Instead of conditions improving, they seem to have been getting worse. In Ireland, civil war is still in progress. Germany was in the throes of a political upheaval. The meaning of the assassination of Rathenau became clear. It evinced the development of a class struggle between the bourgeois and socialistic parties which may rock the country to its foundation and will increase the difficulties of arranging things with the French and solving the reparations problem. In Poland, a similar contest is developing. Austria is already so completely contaminated by the socialist element that it is unable to get outside assistance and is thus falling into a state of despair but little short of what prevails in Russia. The conference at the Hague came to an abortive end for the reason that it was impossible to discuss affairs with the Russians in any reasonable way. The Germans declared their inability to meet the reparation payment that fell clue on July 15 and the Commissioners for the Allies granted them an abate-ment of a portion thereof and are listening attentively to the supplication of the Germans for a moratorium of one or two years. In the United States, July was a month of widespread labor troubles, accompanied by a great deal of disorder and violence, which led to detachments of the National Guard being called out in several states. The railway shopmen, about 400,000 in number, struck on July 1. The road maintenance men decided not to strike, but many thousands of them quit work without the sanc-tion of their union. There were more strikes in the textile industry in New England and in similar industries all over the country. Early in July, it was estimated that about 1,250,000 men were out on strike. The coal strike continued. Early in the month the President summoned operators and miners to Washing-ton and submitted a plan for the compromising of disputes. After a week&apos;s consideration the miners re-fused flatly to agree to anything. The majority of the operators consented to accept the proposed arbitration, but a minority refused. Following this abortive at-tempt the President dismissed the conference with the injunction "to return to your mine properties and resume operation." Production has not increased.

Jan 8, 1922

By J. Norman Bulkley

As electrical power is used to a greater extent on the Rand than in any other mining center, it is thought that a short description of the methods used and results obtained may be of interest. In comparing Rand practice with that on other fields, several general factors should be borne in mind: First, the mines are all working on large tonnages of low-grade ore (average $6.50). The annual crushing rate is about 27,000,000 tons. Second, the mines are all grouped under the financial and engineering control of mining houses, so that the results of a group, rather than an individual mine, are open for study, and practice follows more uniform lines. Third, coal of fair quality (about 12,000 B.t.u.) can be obtained for $2 to $3 per ton. Good supplies of condensing water are, however, scarce, and have to be carefully stored. Power Supply Power is supplied by the Victoria Falls & Transvaal Power Co., Ltd., and its subsidiary, the Rand "Mincs Power Supply Co. Both companies, which are practically one from an engineering point of view, operate the following stations, all fecding into the same system. Capacity Installed Turbo Capacity Installed Steam-Tur- Station Alternators bine Dliven Centrifugal Compressors Brakpan............... Two 12,500-kw. sets Two 3,000-kw. sets Simmer Pan............... Six 3,000-kw. sets Rosherville................ Two 11,000-kw. sets Six 3,500-kw. machines Five 9,600-kw. sets Three 7,000-kw. machines Verckniging ............. Two 9,600-kw. sets Two 12,000-kw. sets 162,200-kw. sets Total steam-tkbine capacity installed, 204,200 kw. There are also at the Robinson Central air station six motor-driven centrifugal compressors, each of 3,500 kw., equal to 22,000 cu. ft. per minute at 120 Ib. capacity at 3,000 r.p.m. Power is supplied from these stations as 50-cycle, three-phase current generally at 40,000 volts,

Jan 1, 1916

W. H. BASSETT, * Waterbury, Conn.-Manganese should not be expected to remedy all the defects that are due to poor melting practice. It is undoubtedly valuable in helping to eliminate porosity in many of the alloys. In the copper-nickel alloys, its use is becoming almost universal, for, beside helping to make sound castings, it tends to hold the carbon in solution in the solidified alloy. GWILLIAM H. CLAMER,? Philadelphia, Pa.-I have found that manganese copper is satisfactory for eliminating sulfur and that it works very well in the crucible and when you have reducing conditions; but in a large reverberatory charge, where the conditions are oxidizing, we were not able to eliminate the sulfur.

Jan 1, 1919

By W. Joseph Schlitt

The types of copper leaching and recovery operations in the United States are reviewed, along with characteristics and trends in the industry. The contribution of the various leach operations to total mine output is discussed in order to provide a perspective on the relative importance of copper leaching as a method of production.

Jan 1, 1980

By E. Marburg

Most ingots complete solidification vertically rather than transversely. This conclusion is based on complete solidification patterns of big-end-up and big-end-down ingots developed from dumped and split ingots. New mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon adequate width of vertical core. A LTHOUGH it has long been recognized that the A internal soundness of ingots is principally been recognizedthatthedependent on the process of solidification, knowledge of this process is still only fragmentary. The mechanisms causing the several types of segregation in ingots, which mechanisms are necessarily related to the solidification process, are not well understood. In absence of a better conception of the solidification process, it seems hardly surprising that mold design varies widely. Guiding principles for mold design are needed. At stake in the improvement of ingot quality are not only improved properties of steel but also appreciably higher yields of sound steel, which would considerably decrease manufacturing costs. In the present study, following a general description of the several types of segregation in ingots, Fig. 1, complete solidification patterns of a big-endup and a big-end-down ingot, including the zones of accelerated solidification, have been reconstructed. In both ingots, a core of vertical solidification extends from the base cone to the hot-top junction. Based on the finding that ingots complete solidification vertically rather than transversely, as has been previously assumed, new mechanisms for segregation in ingots are proposed. Internal soundness in ingots is found to depend upon the width of the vertical core, which in turn depends principally upon the width to height (w/h) ratio of the ingot. Solidification patterns of ingots are of three general types: 1—those in which vertical solidification does not reach the top, 2—those in which vertical solidification just reaches the top of the ingot, and 3—those in which vertical solidification reaches the top some time before transverse solidification would reach the middle of the ingot, so that a vertical core of definite width at the top of the ingot is developed. Axial defects vary characteristically with the solidification pattern. Examples of ingots of each type are presented. Dumped ingot data reported by Nelson&apos; have been used in developing families of curves of transverse and vertical solidification, and in deriving the effect of the w/h ratio upon the solidification pattern. Photographs of many ingots split at Homestead and at Duquesne Works, United States Steel CO., as well as those published by the British Iron and Steel Institute,&apos; have been studied and analyzed. In the interest of brevity, only typical ingots of each type or classification from the above sources have been reproduced. Segregation in Ingots Segregation in ingots falls into three principal classifications: 1—lamellar segregation, as revealed in sulphur prints (Figs. 2 and 3); 2—zone segregation, or broad variations in composition; and 3— interdendritic, or microsegregation. The last class, of minor importance, is not considered here. When liquid metal cools, according to the theory of differential or selective solidification,2 metal of relatively high purity selectively solidifies first. Liquid segregates (principally carbon, phosphorus,

Jan 1, 1954

By J. T. Peters, N. Schapiro, R. J. Gray

Petrographic studies of coal have resulted in a better understanding of the origin and composition of coal and have added to the knowledge of how and why coals differ in their response to various prepamtion and utilization processes. Petrographic methods can now be used in scientific economic exploitation of coals. Because the United States Steel Corp. is one of the largest consumers of coal and coke, there is a continuing interest in the corporation in perfecting a better understanding of coal so that it can be utilized more effectively. Coal is a heterogeneous substance composed principally of plant material that has been altered by a complex geochemical process to form rock. The science of coal is anthracology. The ultimate aim of anthracology is determining the relationships and differences among coals. The fundamental aim is finding out why coals differ. The practical application is determining how the differences in coals affect their utilization properties. Coal, like other sedimentary rocks, consists of more than one material. Fig. 1, a photograph of a natural fracture and a polished surface of a lump of coal, displays heterogeneity in terms of the banded ingredients present. The earliest attempts to describe coal were based on its hardness and appearance. &apos; Thus, coal has been described as hard or soft, bright or dull, and banded or nonbanded. The variations in the hardness and physical appearance of the coal reflect differences in materials that constitute the coal. The banded nature, lustre, and texture depend upon the relative proportions of the various constituent materials. Even the earliest petrographic investigations of coal produced evidence of of the heterogeneity of the coal substance and shoul have destroyed the concept of the unit coal molecule. Coals (Fig. 2) that appear the same frequently consist of different microscopic materials and may behave differently during mining, pulverization, washing, or coking. In Fig. 3, the upper photograph shows a bright at-trital medium-volatile coal, and the micrograph at the right shows some of the materials that constitute the coal. The lower photograph shows a bright attrital low-volatile coal and the corresponding micrograph shows material of similar origin to those from the medium-volatile coal. Any petrographic description of a coal that has meaning in terms of its utilization begins with a microscopic examination. Numerous attempts have been made to describe coal on the basis of the materials that constitute the coal.2*3 Initial petrographic studies were directed towards the question of the origin of coals without any true basis for studying the metamorphic changes in the

Jan 1, 1962

By Casimir Constable

DURING the years 1875 to 1879 I had charge of the Rockwood furnaces and mines, situated forty miles from the nearest railway communication at that time, and one hundred miles north of Chap tanooga, Tenn., by the Tennessee River. The small furnace with old-fashioned stoves, then in blast, was built under great difficulties by General Wilder. The early conditions were somewhat as follows: The ore was fossil ore of the Clinton group ; very fine and generally wet, without other admixture. The coke had a large amount of ash, and the fur" nace appeared to be badly scaffolded at times. On many days only a few tons of iron could be obtained. The founder generally id creased the revolutions of the engine when signs of chilling appeared,. The cinder at such times was black, very scoriatious, often closely resembling mill cinder. When the pressure was increased (the joints being the old-fashioned rust joints), leaks in the blast-pipe occurred It was noted that when the blast was stopped, and the leak bolt imperfectly remedied, the furnace improved a little. This set me thinking on the right track; and I took the responsibility of be coming my own founder for a time. A scaffolded condition had existed, and the situation was a trying one. Strange to say the negroes proved excellent furnace-men. Conceiving the hearth of the furnace to be similar to the grate area of a steam-boiler, capable of disposing of but so much fuel per hour, and requiring only a corresponding amount of air, it follows that an excess of air will burn the fuel not yet arrived at the hearth!, and raise the melting-point far above the tuyeres. This might pro duce scaffolding or at any rate choke the boshes, and leave less fuel to be consumed in the hearth. Thus for the time being less ail;. would be needed, as the continued burning of fuel in and above the boshes, would only aggravate the trouble. This condition of affairs accounted for the black cinder; the heat above having melted ore not yet perfectly reduced. This view decided me to reduce the revolutions of the engine; thefurnace finally became gray, as might have been expected. Any attempt to increase the speed produced black cinder and hard iron ;

Jan 1, 1883

By S. L. Payne, J. P. Morris, R. L. Kipp, G. R. Zellars

The activities of iron and nickel in liquid Fe-Ni alloys were determined by measuring the vapor pressures of iron and nickel above the alloys and comparing with the vapor pressures of the pure metals. Nickel was found to deviate negatively from Raoult&apos;s law over the entire composition range. Iron behaves ideally down to 0.7 mole fraction but shows negative deviations at lower concentrations. At 1600°C the activity coefficients at infinite dilution are 0.40 for iron and 0.66 for nickel. 1 HE formulation of the conditions of chemical equilibrium between liquid metals and gases or slags is an important application of thermodynamics to pro- cess metallurgy. Usually the metal and slag phases are solutions of several components; and for accurate calculations, it is often necessary to use the activities of the components in place of their concentrations. Data concerning activities, however, are quite meager. The evaluation of the activities of iron and nickel, presented in this paper, is part of a project to determine activities in iron alloys at elevated temperatures.

Jan 1, 1960

By J. H. Wiggins

Granting that about 600,000,000 bbl. of light oil will be produced in the United States this year and taking the Bureau of Mines&apos; statement that 71/2 per cent. of the total crude production will be lost before the finished gasoline is shipped from the refinery, the volumetric evaporation will be 45,000,000 bbl. of the cream of the gasoline. This is a ConseNative figure and is equivalent to 1,890,000,000 gal. The real value of this liquid is at least 150 per cent. of the value of an equal volume of motor fuel. At only 10 c. per gal., the value lost is $189,000,000; at 15 e. per gal. the loss is $283,000,000. If 750,000,000 bbl. of light and heavy oil are produced here this year and the average price per barrel is $1.333, the gross return to producers will be $1,000,000,000 and the net returns about $200,000,000, if the cost of production is only $1 per barrel. Thus, the evaporation bill is about 20 per cent. of the gross income and is equal to the net income of the crude-oil producers. Two other comparisons with popular phases of the petroleum industry will help give an adequate conception of the evaporation problem. These are: cost of preventing evaporation compared to cost of cracked gasoline and volume of gasoline evaporated compared to volume of gasoline manufactured from natural gas. When gasoline is manufactured from heavy oils by the cracking process, there are two important divisions of the total cost of the product: the manufacturing cost, such as plant cost, operation, maintenance, etc., and the cost of the barrel of heavy oil, from which the cracked gasoline is made. In preventing evaporation loss the cost first mentioned enters into the total cost, but the second cost is eliminated; that is, no charge is necessary for stock from which to manufacture the saving. A detailed analysis of these two costs on a large scale shows that the net income from a dollar spent in preventing evaporation loss from the lease through the refinery is twice the net income from a dollar spent in cracking. Of

Jan 1, 1924

By M. M. Singh

Coal mine operators are obligated to mitigate or plan for subsidence under the new regulations. This paper presents the types of subsidence control measures that may be employed to meet these requirements, which include: changes in mining methods, strata stabilization after coal extraction, construction of specially designed surface structures and foundations to accommodate ground movements, and comprehensive planning and coordination of surface land use with underground mining. The basic principles of these techniques, along with specific procedures that may be followed to implement them, are briefly discussed. Subsidence control methods that are currently being investigated are mentioned.

Jan 1, 1985

By Evans B. Mayo

As a result of studies distributed over the earth- including ocean basins as well as continents- some tectonists recognize four dominant structural trends: 1) northwest; 2) northeast; 3) nearly east- west, or equatorial; and 4) nearly north-south, or meridional. Baker&apos; proposed a theory to account for these trends and Sonder5 called their world-wide arrangement the regmatic shear pattern. Moody and Hill6 proposed a much more complicated shear network which, although fascinating and perhaps ultimately useful, will not be followed here. In a recent review of deformation within the Cordillera, Wisser7 mentioned the four fundamental directions. The fact that many geologists deny the existence of the regmatic shear pattern implies that the fundamental structures are far from obvious. It may mean, also, that some geologists are not accustomed to examine regional and world maps analytically. The maps require much study, and certain features, should be isolated on overlays. Even so, with the present limited knowledge, uncertainties remain. The following analysis is a qualitative experiment, subject to change as information accumulates, and should be supplemented by the western sheet of the Tectonic Map of the United States.8

Jan 11, 1958

By W. Tovote

THIS paper is based upon 12 years&apos; experience in the Southwest, including three years that were spent in constant traveling as examining engineer for the Phelps-Dodge Corporation. The material was gathered during rather extensive work in Bisbee, Clifton-Morenci, Globe, and Tombstone, and also on short and rapid trips into most of the mining camps and prospect fields of New Mexico, Arizona, the desert country of California, and as much of Sonora as was safe at the time. My methods of observation and my deductions are not put forward as new or scientific; they are simply rough field methods, based upon short notes, rough sketches, and largely upon memory, which I have found useful for coordinating geological data for the purpose of passing quick judgment on mining possibilities in certain districts exhibiting uniform characteristics. The opportunities for observation have been better these last few years than ever before, clue to the unprecedented activity in mining, which has caused the reopening of hundreds of old mines and the starting of even more numerous prospects all over the mining States. POSSIBLE SYSTEMS OF CLASSIFICATION By Geological Provinces There are a number of well defined geological provinces in the territory under discussion, and a study of their individual features is of interest. The following are a few of those that axe most striking in their uniformity. 1. The "Desert province," extending roughly from. Wickenburg, Ariz., to and beyond Barstow, Cal. In its north-south extent it reaches up to the Colorado River and clown into Sonora, but overlaps other provinces. It is characterized by a worn-down basement of schistose and granitic rocks, on which rest remnants of Paleozoic and pre-Paleozoic sediments, including very old limestones. The sediments are disrupted and contorted. Alteration in the mineralized areas is very prominent, especially in the schists and limestones. Cenozoic volcanic rocks, principally of semi-basic composition, have been intruded into this complex and sometimes cover it as lava flows.

Jan 10, 1918

By H. M. Crankshaw

The early methods of mining anthracite in the steep pitching Mammoth bed consisted in driving breasts up the pitch from the gangways and airways driven in the bed along the strike (Plate 2, Fig. 1). Breasts are simply rooms driven up the pitch the full thickness of the bed (Plate 2, Fig. 2), having a width of from 18 to 30 ft., and a manway or traveling way on one or both sides. (For detail of breast method see Whildin, Trans., vol. 50, p. 704). Many difficulties were encountered, and the maintenance cost of the timbered gangways was so great as to be practically prohibitive. To reduce this expense, the gangways were driven in the thin Skidmore bed underlying the Mammoth, and the coal mined through rock holes. (Plate 2, Fig. 2, A.) It was found that after the breasts were driven up 80 to 100 ft., the coal almost invariably rushed or "ran away," making good ventilation almost impossible and the extraction of coal from the upper portion of the lift very difficult. The economic length of a lift is from 200 to 250 ft., and the percentage of extraction by the old method above mentioned was often under 50 per cent., while the coal recovered was so badly broken up as to reduce materially the percentage of large sizes. Principles of Present Mining Methods The present methods designed for the recovery of a maximum percentage of coal and a maximum yield of the prepared sizes depends largely on the following principles: First.—Formerly the practice in mining bituminous coal was to space rooms so that as much coal as possible could be extracted in first mining (Plate 3). The small pillars were often lost, and an improvement in total extraction was found in the system of driving narrow rooms with wide pillars, with a much larger final recovery (Plate 4). Second.—The early method of ventilation was to maintain a single

Jan 1, 1917

By J. M. Uys, T. B. King

The solubility of water in silicate melts of various compositions was measured. The basicity of the silicate did not appreciably affect the water solu-bulity at low-base content (acid compositions). Near the orthosilicate composition the solubility increased with basicity for silicates in which the cation displayed a weak ion-oxygen attraction and apparently decreased for those in which the cation showed a strong ion-oxygen attraction; metasilicates of the former class dissolved more water than those of the latter. Temperature had little effect on water solubility. The experimental results are interpreted on the basis of two modes of solution, the contribution of one decreasing, and that of the other increas -ing, with increased melt basicity. In the former, solution occurs through interaction with doubly-bonded oxygen atoms and in the latter, through interaction with singly-bonded oxygen atoms, or, in very basic melts, through reaction with free oxygen ions. THE hydrogen content of a steel melt is in a large measure determined by water dissolved in the slag. In some glasses water may be a major cause of "seeds". Water vapor in the furnace atmosphere is the primary source in both instances. A knowledge of the mechanism of water solution in silicate melts should help in assessment of practical methods for its control in steelmaking and glass refining. Walsh et a1.l measured the water content, expressed as hydrogen, of 40 pct lime-20 pct alumina-40 pct silica and 62 pct manganese oxide-38 pct silica melts as a function of the steam partial pressure, in equilibrium with the melt. Tomlinson 2 and, also, Russell3 investigated this relationship for a molten 30 pct soda-70 pct silica glass. In all three investigations, the solubility of water was found to be proportional to the square root of the partial pressure of steam. Moulson and Roberts 4 confirmed this relationship for a silica glass. On the basis of the square root relationship, Tomlinson2 and Russell3 interpreted the solution reaction as "network-breaking", similar to that expected on the addition of metal oxides to silica. Walsh et al.&apos; postulated two possible modes of solution, one the mechanism suggested by Tomlinson and Russell and the other the reaction of the water molecule with an oxygen ion to form hydroxyl ions. These two modes of solution suggest opposite effects of melt basicity on water solubility. However, little appears to be known about the effect of melt basicity on water solubility. Walsh et a1.l found, in the lime-silica system, that the water content increased slightly with increased basicity. As these authors pointed out, this does not appear to be in accord with their further observation that slags containing little or no silica dissolve very little water. Kurkjian and Russell5 measured the effect of basicity on water solubility in alkali silicates in the composition range 15 to 45 mole pct alkali oxide. They found a minimum in the water content at about 25 mole pct alkali. This was interpreted on the basis of two concurrent solution reacZions; one in which solubility was proportional to the activity of doubly-bonded oxygen and, in the other, proportional to the activity of singly-bonded oxygen. The present work was aimed at establishing the effect of basicity on water solubility in silicate melts over as wide a range of compositions as practical. APPARATUS AND EXPERIMENTAL PROCEDURE The silicate melt was equilibrated with a "carrier-gas" of accurately known water content, quenched, and analyzed for water by a vacuum fusion technique. Some pertinent details of the equilibration procedure, analysis technique, preparation, and handling of the silicates are given below. Gas-Silicate Equilibration. The apparatus used to equilibrate the melt with the gas mixture was similar to that used by Walsh et al.&apos; but with some important modifications.6 Purification trains were provided for nitrogen and hydrogen; whenever air or oxygen was used as carrier gas the nitrogen purifiCation train was used with the copper furnace at room temperature. Gas flow rates were measured with capillary flow meters; bleeders filled with a mixture of dibromo and tribromo ethyl benzene (density about 2 g per cc) were used for convenience in controlling flow rates.

Jan 1, 1963