Search Documents

By R. O. Williams

Measurements have been made of the internal energy of deformation in a Cu-A1 alloy and a Cu-Zn alloy as the deference between the work and the released heat. The method required the rapid compression of samples to reduce thermal interactions. The rate of energy storage is low initially but then becomes almost linear with strain. Both alloys stored about 60 cal per mole at a strain of 0.4 in the recrystallized condition. The fractional rate of storage increases at low strains reaching about 0.25 at a strain of 0.15 and then decreases slowly with increasing strains. As do pure metals, these alloys release appreciable energy immediately following deformation; in contrast with pure metals, however, the release continued for extended periods of time. This energy release is somewhat sensitive to the amount of deformation, the deformation temperature, and prior thermal & eatment. It is believed that this release is a composite of that observed in pure metals which has been attributed to dislocations and that due to the motion of vacancies which produces increased short-range order. IT is expected that changes brought about by deformation of a pure metal can be understood in terms of the three defects—dislocations, vacancies, and interstitials—along with the interactions possible between these defects. Frequently stacking faults are created and must also be considered. 1t is not immediately clear whether or not the stress fields which are created should be regarded as independent of dislocations. For alloys there is the important additional effect of atomic configuration, for example short-range order, which must also be considered and will, in general, interact with each of the above defects. While it is true that a complete understanding of pure metals is not yet possible, it would seem very valuable to establish the similarities and differences between pure metals and alloys. Such knowledge could contribute to the understanding of both. A study of the changes in internal energy resulting from deformation of two alloys is reported here. Although some information has been available for alloys almost as long as for pure metals, the volume of work has been substantially less. Sato' and Quinney and Taylor' were responsible for the earlier work, both using brass and annealing calorimetry. tizhnova' studied stored energy in Cu-Ni alloys by a method somewhat similar to the one reported here. Bever and his co-workers have made extensive studies of Au-Ag alloys4'5 and more recently CU-AU'U' using solution calorimetry. Clarebrough et a1.' have recently studied brass using annealing calorimetry. EXPERIMENTAL METHOD The present results were obtained by the rapid, adiabatic compression of a sample about 1/4 in, diam by 1/2 in. long between two tungsten carbide hammers. A vacuum provided thermal isolation and oil provided effective lubrication between the sample and hammers. The increase in internal energy is the difference between the mechanical energy and the heat liberated within the sample. The mechanical energy was determined from the velocity of the hammers (calculated from the height through which the hammers traveled) and was essentially constant for each deformation cycle. The heat was determined from the temperature increase of the sample which was measured by an embedded thermocouple. Specific heat data were calculated from Neumann's rule using tabulated data for pure metals.9 Since the fraction of the energy which is stored is large compared to that for pure metals, specific heat data of high accuracy are not required. Successive increments of deformation were carried out by repeating the procedure, the limit being determined mostly by the decreasing accuracy caused by the increasing corrections and the decreasing storage of energy. About five cycles were used to give a true strain of about 0.5 while the time interval between cycles was 1 to 2hr.

Jan 1, 1963

By Blake M. Loring

Recently the S-curves for 30 to 40 alloy steels have been pub1ished.l.2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.29 per cent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr, at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1¼ by ½ by ? in. Wires attached to the samples were used for handling. instead of tongs, to avoid chilling. The specimens were heated at 845°C. for ½ hr. and quenched into constant-temperature salt baths held at various temperatures from 205' to 650°C. The time required to transfer the specimens was found to be about 1½ sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 2I°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1942

By Blake M. Loring

Recently the S-curves for 30 to 40 alloy steels have been pub1ished.l.2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.29 per cent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr, at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1¼ by ½ by ? in. Wires attached to the samples were used for handling. instead of tongs, to avoid chilling. The specimens were heated at 845°C. for ½ hr. and quenched into constant-temperature salt baths held at various temperatures from 205' to 650°C. The time required to transfer the specimens was found to be about 1½ sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 2I°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1942

This paper "On Coal" was published in three issues of The Western Gleaner in 1814. Name of author is not given. This magazine was started by Cramer, Spear & Eichbaum, in Pittsburgh, Pa., in December 1813, and ran for about two years. Copies are very rare, and this one is made from an original in the Darlington Library, University of Pittsburgh. This is almost certainly the first general article on coal published west of the Allegheny Mountains, and one of the earliest in this country. ON COAL Its Natural History-Mining of Coal-Phenomena occasioned by Fire-damp-Method of Coking-Distillation of Tar from Pit-coal-Gas-light-Coal, a Manure I. NATURAL HISTORY OF COAL There are few productions of nature which present to the philosopher a wider field of investigation than pit-coal. A substance highly inflammable is found in the deep recesses of the earth, sometimes loaded with numerous superincumbent strata of hard rock, and extending frequently along with these strata through a vast expanse of territory. Though metals may be said to be inflammable substances, as they combine more or less rapidly with oxygen when placed under particular circumstances, yet the character of rapid combustion with disengagement of light and heat, seems to belong. principally to such substances as are derived either from the animal or vegetable kingdom. That this is probably the case with regard to coal we are further induced to believe, by the remarkable circumstance, that the chemical analysis of this natural production yields especially, though in various proportions, those materials which constitute essentially the vegetable. And if any thing was wanting to confirm, us in that opinion we might trace in a number of fossile substances the gradual transition of the vegetable into the state of mineral coal. This fact is so intimately connected with the natural history of coal, that we cannot think it superfluous to give it some farther development. Among the great number of principles which the chemist is capable of tracing in the vegetable kingdom, the presence of extract, resin and fibre seem to form the characteristical marks of plants.-If vegetable matter be boiled in water, and the water, after having been strained and filtered, be exposed for some time to the open air, a flocculent precipitate takes `place from every part of the liquor; which soon subsides to the bottom of the vessel containing it. This is the extract; altered, indeed, by exposure, and now no longer soluble in water, a change which is supposed to depend on the absorption of oxygen; and if, by any means the proportion of oxygen be increased, the extract gradually becomes of a darker color, blackens, and approaches to the state of charred wood.

Jan 1, 1942

By C. L. Berrien

MANY fires have occurred in the mines of Butte in recent years, and while all have been of a serious nature, simply because they were mine fires, six of them have been especially dangerous in respect to loss of life and property, and the expense of extinguishing or controlling them. It is not my intention to discuss the relative merits of methods used in fighting these different fires because the conditions under which they occurred varied in each case, and it was not always advisable to expend the large sum of money necessary to actually extinguish them if they could he bulk-headed off from the rest of the mine. It is needless to say that everything possible has been done to check all fires at the beginning, but without success in some cases; and it has then become necessary to bulkhead all connections to them, in which state several now exist. The mine fires of Butte, or fires in any mine, may be divided into two classes, namely: Those occurring in accessible workings, and those occurring in inaccessible workings; because these two conditions govern to the greatest extent the methods of fighting fires. Accessibility and in-accessibility in the case of mine fires concern not only new open workings and old closed workings, respectively, but also the condition of the ventilation in and about those places. When a fire is accessible at the start it should not be difficult to confine it to a small area and extinguish it in a relatively short time, but when it is impossible to actually reach a fire in old filled, abandoned workings, or there is no opening by which the gases may be conducted away from the fire zone, then the time consumed in changing those conditions permits the fire to increase to such an extent that it is a long, hard fight to overcome it.

Jan 6, 1915

By C. R. Woodcock, J. S. Mason

In almost any situation where particulate or granular bulk solids have to be conveyed, whether for a distance of a few metres or for many hundreds of metres, a pneumatic conveying system may be considered. Conveying by pipeline is convenient and clean, but running costs may be substantial because of the heavy air consumption and the trend has therefore been towards dense-phase transport in which the ratio of conveyed solids to conveying air is kept high. This paper concentrates on air-float conveying, which can be regarded as an extreme form of dense-phase conveying where the bulk solid is fluidised in a channel and then caused to flow, either by inclining the channel or creating a pressure gradient along 'it. Various designs of air-float conveyor for upward, horizontal and down- ward transport of powders are discussed, with special emphasis on the latter case. In situations where a continuous downward slope can be provided, the combination of air-fluidisation and gravity flow results in a conveying system that, for many kinds of bulk particulate solid, would be hard to better in terms of convenience, reliability and economy. The paper is concluded with a discussion of design features and performance of practical air-gravity conveyors, involving the handling of various bulk particulate solids, both in research and in full-scale industria1 applications.

Jan 1, 1980

By S. F. Shaw

The Sierra Mojada mining district is situated in western Coahuila, about 8 km. east of the Chihuahua state line, and about one-half way from the northern to the southern extremity of the state. It is at the terminus of the Mexican Northern R. R., 125 km. northeast of Escal6n, Chihuahua; also about, 240 km. due west of Monclova, Coahuila. The altitude is approximately 1500 m. above sea level. The Sierra Mojada valley is about 10 km. long, from east to west, with a width of 1 to 2 km. It is approached from the east through the Puerto del Oro, where the Mexican Northern R. R. enters the valley; the slope from west to east is gentle. The Sierra Mojada, of which about 300 m. is an almost vertical wall, bounds the valley on the south side; on the north side, the slope to the crest of Sierra Planchada is more gradual, rising only 200 or 300 m. above the valley. Water is relatively scarce in the district, and there are no running streams. The rainy season, usually beginning at the middle of June, lasts through July, and occasionally into August or September. In some years the rains fail entirely. The slope of the ground is such that nearly all the water immediately runs off. The arroyos along the flanks of the mountains are not very deep, but in heavy rains, sometimes approaching cloudbursts, a tremendous volume of water rushes down them, carrying large boulders. A certain amount of seepage collects in the agglomerate, lying below the conglomerate, and is retained in the local fractures. Some shallow wells have been sunk in this agglomerate, and one well over 150 m. deep was sunk on the Volcan ranch, supplying about 76 1. (20 gal.) per min. A considerable supply of water is collected in large earth reservoirs in and below the town of Esmeralda. In ordinary years this supply will last until January or February, after which the Volcan well has to be depended on until the next rainy season. Vegetation is scarce, aside from scanty scrub oak and other brush in the mountains, and a few mezquite, locust, pepper, and cottonwood trees

Jan 1, 1923

By S. F. Shaw

The Sierra Mojada mining district is situated in western Coahuila, about 8 km. east of the Chihuahua state line, and about one-half way from the northern to the southern extremity of the state. It is at the terminus of the Mexican Northern R. R., 125 km. northeast of Escal6n, Chihuahua; also about, 240 km. due west of Monclova, Coahuila. The altitude is approximately 1500 m. above sea level. The Sierra Mojada valley is about 10 km. long, from east to west, with a width of 1 to 2 km. It is approached from the east through the Puerto del Oro, where the Mexican Northern R. R. enters the valley; the slope from west to east is gentle. The Sierra Mojada, of which about 300 m. is an almost vertical wall, bounds the valley on the south side; on the north side, the slope to the crest of Sierra Planchada is more gradual, rising only 200 or 300 m. above the valley. Water is relatively scarce in the district, and there are no running streams. The rainy season, usually beginning at the middle of June, lasts through July, and occasionally into August or September. In some years the rains fail entirely. The slope of the ground is such that nearly all the water immediately runs off. The arroyos along the flanks of the mountains are not very deep, but in heavy rains, sometimes approaching cloudbursts, a tremendous volume of water rushes down them, carrying large boulders. A certain amount of seepage collects in the agglomerate, lying below the conglomerate, and is retained in the local fractures. Some shallow wells have been sunk in this agglomerate, and one well over 150 m. deep was sunk on the Volcan ranch, supplying about 76 1. (20 gal.) per min. A considerable supply of water is collected in large earth reservoirs in and below the town of Esmeralda. In ordinary years this supply will last until January or February, after which the Volcan well has to be depended on until the next rainy season. Vegetation is scarce, aside from scanty scrub oak and other brush in the mountains, and a few mezquite, locust, pepper, and cottonwood trees

Jan 1, 1923

By F. W. Gibson

A detailed description of the smelting and refining operations of the Amax-Homestake Lead Toller's smelter at Buick, Missouri. This is one of two completely new lead smelting and refining operations to go into operation in the United States in over forty years. Incorporated into the operation are the new methods and equipment which have been developed and lend themselves to the particular metallurgy of this plant. The text, as well as the statistical data presented, represent actual current practice after 22 months of operation, and although the metallurgy is considered to be relatively simple, several metallurgical problems unique to Missouri concentrates are discussed.

Jan 1, 1970

By Joseph Perry

MAGNESITE is found in 22 California counties, but many of the deposits are too small or too impure to be of commercial value. Several of sub-stantial size and quality were entirely exhausted by wartime operation. At present, three properties comprise the only known workable deposits in the state. Of these, the Western mine and the Patterson mine have been known and worked for many years, and have been described in con-siderable detail in various publications, therefore need only brief mention here, because of their proximity to the Bald Eagle mine. The latter, recently developed, is unusual in type of ore deposit, plant design and operation, as well as products made, and very little has been written concerning it. WESTERN MINE The Western mine, 32 miles south of Livermore, Calif., was formerly operated by C. S. Maltby. It has been a consistent producer for many years.1 The ore is of amorphous variety, occurring along fracture zones in serpentine. The veins vary greatly in width, the average being perhaps 8 ft., with the maximum indicated in one early stope of 40 ft.; 2 ft. is considered the minimum for economical mining. The strike of the veins is predominantly north and south, with dip to the west varying from 40° to 75°. Walls are well defined and as a rule firm and easily supported, Veins range in length from a few hundred feet to 1000 or more. Their maximum vertical extent is about 350 ft., but many run less. Early mining consisted of open-cut and glory-hole work on the larger outcrops. This was followed underground by a modified shrinkage system, the waste and low-grade horses being removed by hand sorting on the tramming levels and transported to surface dumps. Filled-stope mining is used now, in order to eliminate the handling of waste, which has

Jan 1, 1938

By N. Mungan

A study was made of the effects of wettability and interfacial tension on the immiscible displacement of a Iiquid by another Iiquid from porous media. The influence of viscosity ratio was also investigated. Porous media used were polytetrafluoroethylene (TFE) cores prepared by compressing TFE powder under different pressures. lt is shown that displacement of a wetting by a nonwetting Iiquid is always less efficient than the displacement of a nonwetting by a wetting fluid, all other things being equal. In the former case, the recovery efficiency can be increased substantially by either reducing the interfacial tension or increasing the viscosity of the displacing fluid. A qualitative discussion is given on the implications of this work to the recovery of crude oil by water flooding. INTRODUCTION The high cost of oil exploration and new recovery schemes makes it imperative that waterflooding be conducted under conditions favoring most efficient oil recovery. To improve oil recovery by waterflooding, it is essential that the role played by interfacial forces in the entrapment of residual oil be studied and understood. Interfacial phenomena in natural rock, connate water and crude oil systems are very complicated because of the complexity of the natural liquids found in petroleum reservoirs, because of our inability to adequately describe the geometrical structure of the porous media and because of a lack of understanding of physical and chemical interactions between the liquids and surface of the pores. The problem becomes further complicated when one tries to elucidate the role of interfacial phenomena in fluid flow. Numerous studies of the displacement of oil by water under different interfacial tension or wet-tability conditions have been made.lm3 These studies have been performed in silica, alundum or sandstone systems using water and paraffin oil and also some surface active material to control the interfacial tension s and the contact angle 0. Unfortunately, the high energies of various interfaces involved favor adsorption and orientation of the surface active material at the interfaces. Also the surface active material concentration at the interfaces exceeds that in the bulk of the liquid phases. Such surface excess may cause the surfactant distribution, the contact angle and the interfacial tension to differ from their measured static equilibrium values and makes interpretation of the displacement experiments difficult. Furthermore, as changes in s also lead to changes in cos 0, the role played individually by one of these parameters in the displacement becomes obscured by the effect of the other. To circumvent these difficulties, a low surface energy solid and true solutions or pure liquids should be used. Use of a low surface energy solid minimizes adsorption and orientation effects at the solid-liquid interfaces. By controlling s and cos 0 through use of selected pairs of pure liquids or true solutions rather than by surfactants, the adsorption effects at liquid-liquid interfaces are eliminated. In the present study TFE cores were used as the porous media. Liquids used were water, sucrose solutions, paraffin oils and benzyl, n-butyl and isobutyl alcohols. The interfacial tension was varied from 40 to 1.1 dynes/cm by suitably choosing the liquid pair. A surface active material was added to the water-oil system only in the case where interfacial tension of 0.5 dyne/ cm was desired. No precise changes of cos 0 were attempted. However, either the displaced or the displacing liquid could be made the one which preferentially wets the TFE surface. Using sucrose solutions and blends of paraffin oils proved to be a convenient way of changing the viscosity ratio between the displaced and displacing liquids. The present investigation examines the effect of interfacial tension, wettability and viscosity ratio on the immiscible liquid-liquid displacement from porous media. Observed data permit a

Jan 1, 1967

By Howard Scott

Invar is the preeminent low-expansion metal by virtue of the fact that it can be prepared with a zero coefficient of expansion at atmospheric temperature. This fact suggests that there is little room for improvement in the expansion properties of the low-expansion nickel steels. The inference is true, however, only so far as the expansion at and near atmospheric temperature is concerned, because the expansivity of invar starts to increase rapidly on heating above 100" C. and soon reaches the value of copper. Guillaumel met this situation by increasing the nickel content above that of invar. By that expedient, alloys having low expansivity under higher temperatures were obtained, but not without a large increase in minimum expansivity. The increase in minimum expansivity with increasing nickel content severely limits the technical applications of these alloys at high temperatures. Prospects of improving the expansion characteristics of the nickel steels is offered by alloying. Search for an advantageous alloying addition by analogy with other alloy systems, however, is not productive because the low-expansion characteristic is unique with that system. The rule of mixtures usually gives a fair value of the expansivity of other solid-solution alloys, but in the iron-nickel systems gives a value of 18 X 10-6 per deg. C. whereas the actual value is 1 X 10-6 per deg. C. Apparently suitable additions are not to be deduced from such ingenuous considerations. Recognition of the fact that the temperature range of low expansivity in nickel steels is terminated with loss of magnetism affords a more promising basis for the selection of an advantageous element. One may expect from that fact that additions of nonmagnetic elements to the iron-nickel alloys are detrimental to the low-expansion characteristic. Indeed, carbon, manganese, silicon, copper and chromium are detrimental to the expansion properties and no nonmagnetic element is reported to be beneficial. From the same viewpoint, the addition of a magnetic metal offers prospects of improvement. As two of the three ferromagnetic elements are already present in the

Jan 1, 1930

By Dennis H. Laubscher

INTRODUCTION The selection of mass mining methods is the situation facing not only planners of new operations, but also those involved with cur- rent operations, including the eventual change from open-pit to underground. Increasing ground control problems on many mines, plus a better understanding of dilution and ore loss problems have meant a review of current mining methods and support techniques. Experiments are only successful if conducted in the right mining environment and on the right scale. Mining personnel have been known for their conservatism and will tend to persevere with an established method rather than change; often, hidden costs will obscure the correct economic assessment. An established mining sequence is not necessarily correct in the long term. However, recommendations to change are usually met with opposition because of inconvenience, temporary production problems and the desire for a trouble-free guarantee. In any planning exercise, care must be taken that time and money are not wasted in trying to achieve the unattainable. During the decision-making period, production personnel must be involved, and, if possible, they should visit similar omrations to that proposed. Co-operative production personnel will help ensure success. Descriptions of mining methods are available in technical papers and books, and it is not intended to discuss this aspect, but, rather, the various factors which must be recognised before arriving at a final selection. In another paper presented at this Conference (Heslop and Laubscher, 1981) factors affecting ore recovery and dilution are discussed in greater detail for various cave mining methods. PRELIMINARY CONSIDERATIONS Comprehensive Geological Data. Geological information is available during the exploration stage, but, often, core from exploration drilling is not analysed with the selection of a mining method in mind. Drilling costs are high, therefore the maximum benefits must be derived from this operation. Holes which have not intersected ore may provide data on possible shaft sites, and 35 mm colour slides of core, sound logging and geomechanics classification, will provide a record which can be used with confidence at a later date. Intersections of the various rock types should be kept for future study; for example, is weathering likely to be a problem, bearing in mind that this can be accelerated in the warm, humid atmosphere of an underground mine. The accumulation of data required to select a mining method starts with initial geological work in the target area, whether this be surface mapping or a diamond drill hole. Publications. As technical papers, reports and books are used in the selection of mining methods, an appeal is made to authors to describe the geological environment so that readers can relate to their own conditions. Not enough emphasis is given to the problems experienced and the techniques employed to overcome them. Follow-up papers are seldom written and we should be prepared to discuss our failures. Diagrams are often misleading, as the ideal and not actual situations are depicted. The caved ore/waste interface is not a straight line, and whereas this may not be significant in a diagram of a 200-117 draw height, it certainly is in sub-level caving with draw zones only 1 - 2 m width but up to 20 m high. SUMMARY OF FACTORS AFFECTING THE SELECTION OF UNDERGROUND MASS MINING METHODS (a) Regional rock stresses and mining geometry. (b) The geomechanics rock mass classification of the orebody and surrounding rock mass. (c) Ratio of the surface area of the ore/unpay interface to the contained ore which determines ore losses and dilution. (d) The cavability and fragmentation data of the ore and hangingwall. (e) The mineral distribution in the orebody and its dilution zone.

Jan 1, 1981

By G. O. Prickett, P. Somasundaran

An experimental progmm based on statistical principles is used for optimizing a flotation operation for the separation of minerals. In this case, flotation of sylvite from sylvinite ore with amine and starch as the flotation reagents was studied to find the optimum reagent levels at various slime levels. The experiments were first done on a two-level three-factor design. Analysis of the results showed that the interactions between various factors were significant. Hence, a first-order linear model of the flotation response would not be accurate. The two-level three-factor design was expanded into a composite design in order to test the fit of a higher-order model. Data were treated to obtain an expression for flotation response as a function of the different variables, to predict the optimum reaaent levels at various slime levels, and also to determine the path of steepest ascent. Tests around the predicted optimum and along the path of the steepest ascent were done until a near-optimum region was obtained. Exploration of the nature of the response surface in that region established the actual location of the maximum response. The optimum amine level was found to be 0.20 lb of amine per ten of ore at all slime levels, while the optimum starch level varied as a function of the slime present. Computer access at the laboratory by means of a teletype terminal on a commercial time-sharing system enabled efficient and accurate treatment of experimental data. The efficiency of experimental investigations can be improved significantly by the use of experimental design and data analysis based on statistical principles. The common approach used in experimental research is to study a property of a system as a function of "one-variable-at-a-time". Several authors'-4 have pointed out the inadequacy and deceptiveness of this method. Results obtained for the effects of a variable on the measured response of the system using

Jan 1, 1970

By Wallace Pratt

INTRODUCTION IRON-ORE deposits in the Philippine Islands became the subject of official record as early as 1664. Undoubtedly iron ore was known and recognized by the Filipinos long before the earliest Spanish records. It is even possible that the Filipino practice of smelting iron ore is, like the native copper smelting, older than the Spanish conquest of the islands. The first records have to do with the magnetite-hematite ores near the towns of Santa Inez and Bosoboso in Rizal Province, from 15 to 20 miles east of Manila. The magnetite-hematite ores of Bulacan were exploited in 1783. Similar ores near the town of Mambulao in Camarines Province yielded a number of specimens to be exhibited in Spain in 1834. With the exception, then, of the lateritic iron ores on the eastern coast of northern Surigao, the true nature of which was not recognized until 1914, the important iron-ore deposits of the Philippines had all been discovered before the islands came under the dominion of the United States. Indeed, in the Spanish documents relating to the history of iron mining are statements which, if their accuracy be not questioned, leave us in the Philippines today with much less iron ore than the Spaniards found. To quote, for example, a report submitted to the Superior Government in Spain in 1835 by one of its emissaries, Don Lorenzo Calvo: "The Philippine Islands, most excellent Sir, possess iron and exhibit it in nearly every known mineralogical combination, and in such abundance that the cordillera of the island of Luzon, from Montufar Point in San Bernardino Straits to Cape Bojeador, is composed of no other mineral than iron, its ranges, of the third order, being in content and structure totally iron of the best quality, the more valuable in that its combinations are such as to facilitate its fusion and to render its reduction to metal simple."

Jan 2, 1916

By C. C. Wright, T. S. Spicer

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By T. S. Spicer, C. C. Wright

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By R. E. Cech, J. H. Hollomon

KURDJUMOV and Maksimova reported experiments with manganese steels and high carbon steels' and with an Fe-Ni-Mn alloy' in which mar-tensite was formed isothermally over a range of temperatures. They found in some cases that mar-tensite formation could be suppressed by rapid quenching to liquid nitrogen temperature. From their microstructural observations of martensite formed isothermally, they concluded that the rate controlling step is nucleation rather than growth. Kulin and Cohen,3 in an attempt to reproduce these experiments, found that with a steel having the same composition as that reported by Kurd-jumov and Maksimova, the transformation to martensite was essentially complete above the temperature range of Kurdjumov and Maksimova's isotherms. The possible reasons for this disagreement were not considered. Recent papers by Das Gupta and Lement4 and Kulin and Speich5 report the formation of isothermal martensite in a high chromium steel and in an Fe-Cr-Ni alloy, but neither paper can be considered a verification of the original Kurdjumov and Maksimova results. Further, in neither case were the authors able to suppress the formation of martensite entirely. Because of the important bearing the Kurdjumov and Maksimova results have to an understanding of the mechanism of martensite reactions it was felt that an experimental investigation directly concerned with checking the validity of their results was in order. This paper describes the results obtained on the isothermal transformation over the temperature range from —79" to —196°C of an alloy of iron, nickel, and manganese. Experimental Apparatus A 15 lb heat of an alloy containing 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn was melted by induction and cast under argon. The ingot was forged to 1-in. bar and a portion rolled to 1/16x1 1/2-in. strip. This strip was pack-homogenized 300 hr at 1100" in a helium-filled sealed iron tube. The composition after homogenization was 73.2 pct Fe, 22.94 pct Ni, 3.73 pct Mn, 0.05 pct C, and 0.015 pct N. The strips were cut to 1/2-in. width for dilatometer and metal-lographic specimens. Only the center portion of the 11/2-in. strip was used in the present investigation. The dilatometer employed was similar in design to one described by Flinn, Cook, and Fellows." A concentric fused auartz rod and tube assembly with hooks for holding the specimen was mounted so as to transmit the specimen dilation to a 1/10,000 in., 1/10 in. travel dial gage. The dilatometer proper was mounted by means of extension arms to a counterweighted sliding member on a vertical standard. This method of mounting permitted rapid transfer of the dilatometer from the austenitizing furnace to the quenching bath and low temperature chamber. A small electrical vibrator on the dilatometer kept frictional effects of the quartz members at a minimum. The austenitizing unit was a vertical, molybdenum-wound, hydrogen atmosphere furnace maintained at a constant temperature ±3°C by means of constant power input. A 12-in. stainless steel jacketed copper liner having 1/2-in wall thickness acted to equalize the temperature in the hot zone of the furnace. This liner, closed at the bottom end and open at the top to permit entrance of the dilatometer and specimen, was kept filled with dry nitrogen gas. A chromel-alumel thermocouple was placed inside the tube to determine the temperature. The 4-in. dilatometer specimens in the chamber varied less than 1/2° across the specimen length except for a 1 1/20 drop at the end nearest the open end of the furnace. The low temperature isothermal holding bath was a double Dewar arrangement similar to one described by Turnbull7. The outer bath was filled with a refrigerant at a temperature lower than the desired holding temperature. The inner bath was filled with Freon "11" or "12" or a mixture of both, depending upon the holding temperature. This inner bath which tended to be cooled by the outer bath was kept at a constant temperature by introducing a small amount of heat with a manually controlled electric heater. Stirring was accomplished by bubbling dry air through the bath. A Leeds and North-rup type K potentiometer was used to measure the inner bath temperature as indicated by a five element copper-constantan thermopile. The bath temperature was maintained within ±0.2°C of the desired temperature by occasionally adjusting the heater current so as to keep the Leeds and Northrup galvanometer at zero deflection with a constant setting of the potentiometer. Isothermal tests were usually continued for 300 to 400 min and another reading made at approximately 1000 min if the bath, unattended overnight, had not deviated in temperature more than 5°C. Transformation curves are drawn dashed (Fig. 1) through the time region where temperature was not controlled precisely. Experimental Procedure Dilatometer specimens of 1/2x1/16-in. strip were cut to 41/2-in. length and holes were drilled for the quartz hooks with proper spacing to give a 4-in. measured length. A thermocouple consisting of 0.012-in. diameter chrome1 and alumel wires was spot welded to the specimen and threaded between the dilatometer rods to binding posts near the dial

Jan 1, 1954

By Robert Maes, Robert de Strycker

The Fe-Ni-As phase diagram has been established by the study of about a hundred alloys, by microscopic observation, and by thermal analysis, with arsenic contents up to 50 pct. The iron and nickel arsenides present extensive solid-solution fields, owing to the substitution of nickel by iron and vice versa; the extent of the solubility field of each compound has been determined with an accuracy of ±1 pct. In the investigated range of compositions, the solidification reactions were established, and the temperatures of the invariant reaclions detevmined with a preciston of iZ°C in the most favorable and ±5°C in the least favorable cases. The isothermal lines of the liquidus surface have also been drazum, with an accuracy estimated at i5°C. Reactions in the solid state, which take place for the formation or the decomposition of certain phases , were investigated in detail. ThE constitution diagram of the Fe-Ni-As system is fundamental for the understanding of the properties of nickel speiss; these by-products of the extraction of certain nonferrous metals indeed often contain the three elements iron, nickel, and arsenic as main constituents. The Fe-Ni-As system has already been the object of earlier investigations. In 1932, Guertler and Savels-berg' have presented some elements of the ternary phase diagram, for arsenic contents up to 55 pct (all percentages in this paper are given in weight percent), including the vertical section FezAs-Ni&s2. This investigation is, however, incomplete and certain anomalies suggested the necessity to verify the results published by these authors: the section Fe2As-Ni5AsZ, for example, is presented as quasi-binary, with a field of complete miscibility in the solid state, even though these compounds do not have the same structure. Recently, ~useck' established an isothermal section at 800°C in the Fe-Ni-As system by X-ray diffraction and microscopic examination of water-quenched alloys. These techniques are sometimes inaccurate for the determination of the fields where alloys are liquid at the investigated temperature, and they may lead to erroneous conclusions when a compound exists at the investigated temperature but is not stable at room temperature and cannot be maintained by quenching. LIMITING BINARY PHASE DIAGRAMS The Fe-As constitution diagram has been the object of several investigations which have been reviewed by Hansen and Anderko.3 For the Ni-As phase diagram, a recent study has been effected by Yund.4 In this system, Heyding and calvert5 have determined the existence of a compound of unidentified structure at arsenic contents slightly higher than those corresponding to Ni5As2 and at temperatures lower than about 200°C; by analogy with iron and cobalt arsenides, this compound could correspond to the formula Ni2As, as suggested by Kulle-rud; although this is not definitely established. In the region of arsenic contents from 35 to 55 pct, Fried-rich7 detected anomalies in the solidification reactions; an interpretation of these anomalies was given by Hansen ,8 which assumed that the solidification reactions in practice are not in equilibrium, but are meta-stable. The main features of the Fe-Ni constitution diagram are the existence of a complete miscibility field, at least at high temperatures, for the fcc phase (which will be designated by My in the remainder of this work) and of a limited solubility field for the bcc phase (designated by Ma). EXPERIMENTAL METHODS The fundamental technique used in this investigation was microscopic observation, which allowed the determination of the reactions occurring during solidification of the alloys, and possible reactions in the solid state.

Jan 1, 1968

By L. W. Blau

THE entrance of geophysics and geochemistry into petroleum engineering may be viewed with apprehension by some engineers. They may not remember the time when "practical oil men" opposed the invasion of engineers into the field of petroleum production. By their excellent contributions they established themselves. In the popular mind, engis veers are practical men whereas physicists and chemists are suspected of being theoretical. It will be best to annihilate this misconception right now at the beginning of a closer relationship between petroleum engineers. geophysicists, and geochemists.

Jan 1, 1943