Search Documents

By O. N. Carlson, A. L. Eustice

The tensile properties of iodide vanadium were determined as a function of hydrogen concentration. It was shown that the presence of 10 ppm H is sufficient to cause embrittlement of vanadzum over a limited temperature range. The temperature of the observed ductility mininlum is approximately -l00°C, this being a function of strain rate and hydrogen concentration. The yield stress of hydrogenated vanadium is raised sharply in the brittle temperature range. THE present investigation was initiated to determine the effect of hydrogen on the tensile properties of high-purity vanadium as a function of temperature and the role of hydrogen in the brittle-ductile transition. Loomis and Carlson&apos; reported a change from ductile to brittle behavior in iodide vanadium at -110°C with a return of ductility at temperatures below -140°C. Vanadium wire containing 270 pprn of hydrogen was brittle at room temperature while wire containing 100 ppm was ductile under the same conditions. Roberts and Rogers&apos; reported a ductile-brittle-ductile fracture sequence in vanadium containing 400 to 600 ppm of hydrogen. Their data show that hydrogenated vanadium is ductile at 150"C, brittle at room temperature and ductile again at -196°C. Magnusson and Baldwin found a minimum in ductility in vanadium containing 80 ppm hydrogen from tensile tests performed at several strain rates. Information available on the vanadium-hydrogen equilibrium system4 is somewhat incomplete. The absorption of hydrogen is exothermic in accordance with the decline in solubility with rising temperature. The limit of solid solubility at temperatures below 400°C has not been determined due to the difficulties in obtaining equilibrium at these temperatures. Data on the hydrides of vanadium are rather limited. Roberts6 studied the structure of VD,., by neutron diffraction, and observed the ordering of the deuterium atoms below -65°C into a primitive cubic cell with a lattice constant about twice that of the disordered bcc vanadium solid solution. EXPERIMENTAL PROCEDURE Vanadium of 99.9 pct purity was prepared by the iodide refining process6 for use in this investigation. This vanadium contained the following analyzed impurities; <20 pprn calcium, 150 ppm carbon, 200 ppm chromium, 30 ppm copper, 10 ppm hydrogen, 200 ppm iron, <20 ppm magnesium, <20 ppm nickel, <5 ppm nitrogen, 150 ppm oxygen, <50 ppm silicon, and <20 ppm titanium. specimen Preparation—Tensile specimens were machined from swaged rods of iodide vanadium. The

Jan 1, 1962

By Jerome Strauss, Carl L. Shapiro

THIS is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years,, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I INFLUENCE OF BODY-CENTERED CUBIC ELEMENTS The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tantalum) are reviewed individually. Iron-carbon-chromium System.-In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts&apos; concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.-Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. a; these results have received general approval. Iron-carbon-molybdenum System.-In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and Reed,8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-

Jan 1, 1943

By S. C. Langdon, Henry S. Rawdon

The following note describing the behavior of copper under rather unusual conditions is offered for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning, as well as softening it. It is well known that metals may be rendered very brittle by electrolytic action in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear 2 similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. TO demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 801" C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for several minutes. When removed from the bath, cooled, and tested for brittleness by bending the specimen back and forth, while clamped firmly at one end in a vise, the copper rod was found to be very brittle, as compared with a rod of the same length of the untreated copper tested

Jan 1, 1921

By T. G. Madgwick, W. Calder

Production of petroleum increased again during 1929, thus maintaining the steady growth inaugurated by the bringing in of Royalite No. 4 in Turner Valley, Alberta, towards the end of 1924, prior to which a decline over a number of years had been experienced. The growth has been confined to the Province of Alberta, the older production in New Brunswick and Ontario showing declines, although in the latter case considerable activity in the search for new gas structures was maintained and during the last six months two wells were brought in, one at Howard in the Trenton at a depth of 1250 ft., giving 5,500,000 cu. ft., and the other at Tilbury in the Guelph or Salina at 750 ft. giving 9,000,000 cubic feet. As has been the case during the past five years, interest in the search for structure and in the following up and development of areas already recognized has centered in Alberta and adjacent portions of Saskatchewan. This was due in the first instance to the striking of wet gas in the Palaeozoic limestone (Madison) of Turner Valley, some 30 miles south of Calgary, in Royalite No. 4 in October, 1924. The bringing in of other wells of similar importance late in 1928 and in the spring of 1929 which extended the productive area 3 miles southwards led to greatly enhanced drilling activity throughout the structure and adjacent areas and in other parts of Alberta. As a result good strikes of heavy crude oil have been recorded during the year at Ribstone, Oyen, Skiff and Coutts, in each case at moderate depths and in sufficient quanitity to justify prolonged testing. The prospects of a satisfactory production of this grade of oil are very encouraging. Actual oil production in the west is still confined to the Province of Alberta and for all grades of oil totaled 997,359 bbl., which compared with previous years shows a gratifying increase. To this increase the naphtha obtained from the wet gas of Turner Valley has proved the principal contributant, heavy crude also showing an improvement, while the light crude, the product of the Cretaceo-Jurassic sands overlying the Paleozoic of Turner Valley, remains unchanged. This is largely owing to operators casing off these sands in their endeavor to reach the limestone, but, there is evidence that in future more attention will be paid to

Jan 1, 1930

By J. B. Clark, F. N. Rhines

brittlement or notch sensitivity progressively increases. Further, in contrast to results obtained with the impact test, the notch strength for the large specimens does not reveal a 500°F embrittlement range. The notch sensitivity as determined with the 0.3-in. specimen of 4340 steel given the stepped austenitizing treatment has been discussed elsewhere. This quantity as measured for the 1.1-in.- diam notch tensile test and given in Fig. 3, is taken to signify that reduced notch sensitivity is encountered in the 600" to 800°F tempering range for specimens given the stepped austenitizing treatment. The stepped austenitizing treatment may, there- fore, be of use in promoting deeper hardenability for a 4340 steel while at the same time giving reduced notch sensitivity in the high-strength range in which this steel is now being used. Acknowledgments The work reported was supported by the U. S. Navy Bureau of Aeronautics. The authors are indebted to the Bureau of Aeronautics for granting permission to publish results of this research and to N. E. Promisel, H. Hessing, and J. Maltz for their interest.

Jan 1, 1958

Jan 1, 1947

By Franc R. Joubin, D. H. James

Uranium exploration in the North Shore area of Lake Huron goes back to 1847 when J. L. LeConte, a distinguished American geologist, identified a pitchblende-like mineral which he called coracite from specimens sent from a locality north of Sault Ste. Marie. In 1948 a search for the LeConte occurrence resulted in discovery of the Camray field, some 70 miles north of Sault Ste. Marie. Prospecting the Camray field yielded about 30 pitchblende occurrences spread over approximately 200 sq miles. Almost without exception these discoveries consisted of narrow, short, pitchblende-filled fractures, within or along the contacts of diabase dykes cutting pre-Cambrian Archean granite and gneiss. Eight discoveries were diamond drilled and three were explored underground, but none proved to be of economic value. Uranium prospecting at this time spread far afield, and it was in 1949 that radioactive conglomerate was discovered in Long Township of the Algoma district midway between and 90 miles from Sault Ste. Marie and Sudbury. F. Joubin examined this discovery at that time but could not interest capital in its development.

Jun 1, 1956

In Bulletin J 1, recently published by the Traylor Engineering and Manufacturing Co., it is stated that the largest jaw crusher ever built has a jaw opening of 66 in. by 86 in. and weighs 680,000 1b. It is said to be in successful operation and has a capacity of 490 tons per hour crushed to 12-in. size; 415 tons per hour crushed to 10-in. size; 330 tons per hour crushed to 8-in. size. The same company, in its Bulletin G 3, gives a diagram showing the percentage of a crushed product which will pass through screens of different sizes of perforation from a machine adjusted to a certain size screen. This diagram is reprinted below for the information of our members and the following notes apply to it. In order to prevent an excessive amount of fines, crushing machines are usually set so that 15 per cent. of the product will be larger than the maximum size desired, and this oversize is then recrushed by smaller

Jan 10, 1916

By Shiro Ban-ya, John F. Elliott, John Chipman

The activity of carbon in Fe-C austenite at 1150°C has been determined for concentrations up to about 2.1 pct C using the equilibrium: C + COz = 2CO; equations have been derived expessing the activity as a function of carbon content on the basis of twelve mathematical models. Several of these represent the data satisfactorily. ACCURATE information on the thermodynamic properties of austenite in the binary system Fe-C is needed as a basis for studies of transformation and precipitation in steels of all sorts, alloy as well as plain carbon. The many attempts to approach this problem through statistical thermodynamics require sound and dependable experimental data in order to evaluate the several models which have been suggested. In this paper we are concerned with the experimental determination of the activity-composition relation in austenite at the temperature of its widest range of stability, approximately the eutectic temperature (1153°C). Accurate investigation of the activity of carbon in austenite may be said to have begun with the work of Dunwald and wagner.&apos; A more detailed study was carried out by R. P. smith2 on the two equilibria: More recent work on these two equilibria has been reviewed by Chipman,3 who pointed out the experimental hazards associated with studies of Eq. [I]. Studies of this reaction involve rather small values of the ratio these are susceptible to errors due to traces of moisture in the apparatus according to the reaction: Ellis, Davidson, and Bodsworth4 evaluated K, for their experimental temperatures and used desiccants to control water vapor pressure. While they were able in this way to obtain consistent values for K1 it cannot be said that all of the uncertainties of the method have been overcome. Results by both methods reported by Schurmann, Schmidt, and wagener5 appear to be consistent except at very low carbon content. Reaction [2] was employed in the experimental work reported here. It is to be recognized, however, that it is not applicable to projected studies of certain alloy steel compositions involving stable oxide-formers.

Jan 1, 1970

By Howard B. Bradley, Charles F. Weinaug

The phase behavior of a naturally occurring hydrocarbon system whose critical temperature is near the reservoir temperature has been described. The same volume per cent liquid was observed for the firkt time at three different pressures for isotherms immediately below the critical temperature. The shapes of the isothermal equilibrium constant curves necessary to predict this phenomena are discussed and illustrated. INTRODUCTION The phase behavior of a number of hydrocarbon systems has been reported; however, very little data are available on natural occurring hydrocarbon systems whose critical temperature is near the reservoir temperature. This appeared to be the case for the fluid studied here; therefore the pressure-volume-temperature data for this system were determined for preqentation. METHOD The PVT data were obtained with equipment similar to hat described by Weinaug and Katz,1 consisting principally of a two-section, double-windowed gauge mounted in a conktant temperature air bath. The procedure followed was essentially that used by Katz and Kurata5 except that a cathetom-eter, reading direct to 0.01 cm, was used to determine the height of each extreme phase limit. The system studied was formed by recombining -.vapor and liquid samples from the first stage separator of the well. Portions of these samples were displaced with mercury into the cell which had previously been filled with mercury. A predetermined amount of the liquid sample was introduced, while an excess of vapor was admitted. The resulting mixture was brought to equilibrium at the condition of the separator during sampling. By adding mercury to maintain the pressure, enough vapor was displaced to give a gas/oil ratio within the cell equal to that produced by the separator at the time of sampling. The remaining material was then considered to be equivalent to the reservoir fluid. An analysis of material in the cell, computed from analysis of vapor and liquid samples and the separator gas/oil ratio. is given in Table I. Table I — Composition of Hydrocarbon System Component Mole Per Cent Carbon Dioxide 0.13 Nitrogen 0.76 Methane 53.91 Ethane 14.20 Propane 9.64 Iso Butane 1.25 Normal Butane 4.29 Iso Pentane 1.12 Normal Pentane 1.87 Hexane 2.72 Heptanes + 10.11 hloleculal. Weight of Heptanes + 178.50

Jan 1, 1951

By Howard B. Bradley, Charles F. Weinaug

The phase behavior of a naturally occurring hydrocarbon system whose critical temperature is near the reservoir temperature has been described. The same volume per cent liquid was observed for the firkt time at three different pressures for isotherms immediately below the critical temperature. The shapes of the isothermal equilibrium constant curves necessary to predict this phenomena are discussed and illustrated. INTRODUCTION The phase behavior of a number of hydrocarbon systems has been reported; however, very little data are available on natural occurring hydrocarbon systems whose critical temperature is near the reservoir temperature. This appeared to be the case for the fluid studied here; therefore the pressure-volume-temperature data for this system were determined for preqentation. METHOD The PVT data were obtained with equipment similar to hat described by Weinaug and Katz,1 consisting principally of a two-section, double-windowed gauge mounted in a conktant temperature air bath. The procedure followed was essentially that used by Katz and Kurata5 except that a cathetom-eter, reading direct to 0.01 cm, was used to determine the height of each extreme phase limit. The system studied was formed by recombining -.vapor and liquid samples from the first stage separator of the well. Portions of these samples were displaced with mercury into the cell which had previously been filled with mercury. A predetermined amount of the liquid sample was introduced, while an excess of vapor was admitted. The resulting mixture was brought to equilibrium at the condition of the separator during sampling. By adding mercury to maintain the pressure, enough vapor was displaced to give a gas/oil ratio within the cell equal to that produced by the separator at the time of sampling. The remaining material was then considered to be equivalent to the reservoir fluid. An analysis of material in the cell, computed from analysis of vapor and liquid samples and the separator gas/oil ratio. is given in Table I. Table I — Composition of Hydrocarbon System Component Mole Per Cent Carbon Dioxide 0.13 Nitrogen 0.76 Methane 53.91 Ethane 14.20 Propane 9.64 Iso Butane 1.25 Normal Butane 4.29 Iso Pentane 1.12 Normal Pentane 1.87 Hexane 2.72 Heptanes + 10.11 hloleculal. Weight of Heptanes + 178.50

Jan 1, 1951

By A. B. Johnson, J. S. Browning

The USBM has developed new and improved physical beneficiation techniques for economically recovering potash minerals from high-clay and low-grade ore from the Permian Basin of New Mexico. With the depletion of the high-grade ores a need for changes in industry&apos;s standard methods of recovery is a must. Technology may be improved in the beneficiation of the ore prior to mineral flotation and in brine clarification from the desliming phase to effect a reduction of losses of fine potash and brine in the disposal of the clay slimes. This report summarizes the results of these tests and demonstrates the feasibility of producing products that meet the requirements of the agriculture market, namely, 95% KCl equivalent to 60% K2O with recoveries ranging between 80 and 90%.

Jan 1, 1973

By Lewis A. Riley

I desire to submit, for the consideration and information of the members of the Institute, the following data, drawings, and tables, showing what I believe will be interesting information with regard to the diamond drill, and its uses in developing mineral lands. I would first say that the results given have been obtained during the past two years by means of two drilling machines belonging to the Lehigh Valley Coal Company, operating on their coal lands in the Mahanoy, Lehigh, and Wyoming regions. 1st. A tabulated statement, giving location of borings, date, progress, total cost, itemized cost per foot, etc. 2d. Section showing strata bored in Nos. 5 and 10 holes at Mt. Carmel, see Plate VI. 3d. Section showing strata bored in No. 19 hole at Hazleton, see Plate VI. 4th. Photograph and description of drill No. 2. From the first it will be seen that the total number of test-holes bored up to May 1st of this year is 24; 9 of these are in the Mahanoy region, 6 in the Lehigh region, and 10 in the Wyoming region, in all of which cores have been taken for the whole distance. The total distance bored is 9902 feet. The majority of the holes have been put down for the purpose of proving the lower veins of the coal series, and have had to encounter the harder rocks of the coal formation. Much of the distance has been through the lower conglomerates, going in some cases through the coarse egg conglomerate, the foundation of the coal deposit, and to the green sandstone and red shale which underlie it. These lower sandrocks and conglomerates are among the hardest known to geologists, and present a formidable resistance to the exploring drill. This fact must be taken into consideratiotl in comparisons of cost of drilling, and when considered will still further improve the very favorable results I am able to show in my statement of costs. In illustration, I will cite the work of one bit when boring in the upper or softer rocks of the Wyoming region, where 280 feet were obtained without resetting, while in the Lehigh and Mahanoy regions, in the lower and harder rocks, bits set with the same quality of diamonds would only bore from 3 to 20 feet before being worn out. In this connection it may

By T. MacDONALD

ATHOUGH flotation has been a commercial process for over twenty years, the last two years have witnessed a sudden and phenomenal increase in our knowledge of how to separate minerals heretofore not considered amenable to flotation at all. As remarked by Professor Locke in the January issue. "Either commercial or laboratory flotation is reported on zircon, ilmenite, carnotite, kyanite, scheelite, chromite, fluorite, feldspar, cassiterite, wolframite, barite, and clay. Attractive patents on soap flotation are U. S. Nos. 2,000,656 and 2,040.187. A survey by Ralston in the February E. & M. J. adds many other minerals to this impressive list. The simple but pregnant fact is that any mineral can be coated, directly or indirectly, with a water-repellent coating, and since this is true, it follows that any mineral can be floated. Fundamentally, this is no new discovery, where, for instance, is the mineral that cannot he washed from a pair of dirty hands by means of soap and water, given the absence of refractory greases or oils which would have no proper place in flotation ?

Jan 1, 1937

Discussion of the paper of S. E. Bretherton, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1481 to 1487. S. E., BRETHERTON, San Francisco, Cal.:-Since preparing my paper, our chemist, F. L. Wilson, has been experimenting with Leadville, Colo., oxidized zinc ore and Leadville zinc sulphides containing lead, operating upon 40-1b. lots at a time. His results on Leadville sulphides are as follows: The raw ore contained a trace of gold, 5.04 oz. of silver, 19.1 per cent of zinc, and 7.24 per cent of lead. After roasting the ore contained a trace of gold, 5.72 oz. of silver, 0.75 per cent of copper, 21.7 per cent of zinc, and 8.29 per cent of lead. The loss in weight by leaching was 38.8 per cent. The extraction was 42.8 per cent of the copper, 80.6 per cent of the zinc, 7.1 per cent of the lead, 0.64 per cent of the silver, and no gold. The little .silver that is extracted would be thrown down with the copper when precipitating it from the zinc and both thrown hack into the residue to be smelted. There would be no trouble in smelting the residue with nearly all the sulphur eliminated and containing less than 7 per cent. of zinc. On zinc carbonates containing silicates the results are not satisfactory. H. O. HOFMAN, Boston, Mass. (communication to the Secretary*) :¬The paper by Mr. Bretherton upon the application of ammonia and carbonic acid to the recovery of zinc as oxide from roasted sulphide ore is of interest to me, as the first installation of the Schnabel process for the extraction of zinc from a mixture of zinc oxide, lead oxide (with some cupric oxide), and pellets of enriched lead, produced in steaming liquated zinc-silver-lead crust of the Parkes process, was made at Lautenthal, Harz mountains, where I was chemist. In that capacity I carried out numerous experiments on the Schnabel process, was active in the erecting of the plant, and later had charge of it. After the Lautenthal plant had been in operation for some time a similar one was built at Hoboken-les-Anvers, but both have been abandoned, as the wet process could not compete with the distillation of the liquated zinc-silver-lead crust, now used universally in the Parkes process.

Jan 11, 1913

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members..) Members and guests who registered at institute headquarters during the period Dec. 10, 1915 to Jan. 10, 1916: A. R. Fletcher, Palo Alto, Cal. H. L. Hollis, Chicago, Ill. R. G. Hall,. St. Louis, Mo. Howland Bancroft, Denver, Colo. Walter E. Koch, Terlingua, Tex. G. D. B. Turner, Butte, Mont. George A. Macready, Searchlight, Nev. H. A. Wheeler, St. Louis, Mo. H. W. Edmondson, Concheno, Chili., Mex. George B. Rodgers, St. Francois, Mo. Arthur F. Taggart, New Haven, Conn. Paul S. King, Wilmington, Del. H. V. Winchell, Minneapolis, Minn. G. H. Clevenger, Palo Alto, Cal. Frank A. Ross, Spokane, Wash. J. W. Beard, Syracuse, N. Y. W. D. B. Motter, Jr., Benson Mines, N. Y. Albert De Deken, Louvain, Belgium. S. Le Fevre, Forest Glen, N. Y.. James H. Smith, Jr., Mount Carmel, Pa. E. H. Hamilton, formerly manager of the Virginia Smelting Co., West Norfolk, Va., has become consulting metallurgist to the Consolidated Mining and Smelting Co., of Canada, Ltd., Trail, British Columbia.

Jan 2, 1916

By G. C. Gester

Oil has been produced in Persia and India for many years, but it was not until 1932 that Arabia entered the arena as a potential oil-producing area. In 1930 the Standard Oil Co. of California acquired a concession covering the rights of exploration and exploitation for oil in the Bahrein Islands and in June, 1932, the first commercial production was discovered by the bringing in of a well known as Jebel Dukhan No. 1 on the Island of Bahrein. Since then the Standard Oil Co. of California through its wholly owned subsidiary, The Bahrein Petroleum Co. Ltd., has been carrying on a systematic survey and development program of its concession in the Bahrein Islands. This group of islands, of which Bahrein is the largest, is in the southwestern portion of the Persian Gulf, approximately 25 miles from the mainland of Arabia. Although geographically a part of Arabia, the islands are not a part of the Kingdom of Saudi Arabia. Their government is essentially independent but certain special rights have been granted to Great Britain through a series of treaties. The Island of Bahrein is 32 miles long by 9 1/2 miles wide and covers an area of 215 square miles. Approximately three-fourths of the island is occupied by a relatively low, broad, elliptically shaped dissected hill, the central part of which is slightly depressed with inward-facing cliffs but culminating in the Jebel Dukhan (Hill of Smoke), which rises to an elevation of 443 ft. above sea level. The topography of the island is a good index of its geologic structure. Structurally the island is an elongated dome or quaquaversal fold composed of rocks of Eocene age. The major axis of the fold strikes N.5W. All of the topographic high portion of the island is a part of the structural uplift. The crest of the fold is broad and flat with the dips increasing on the flanks. How far tilted strata may continue beyond the line where the Eocene beds are covered by recent sands and detrital material is not known. Superimposed on the general structure are a few small irregularities in the form of minor folding and faulting. There is, however, no evidence of any major faults. The largest of the irregularities lies to the south of Jebel Dukhan and has the appearance of a sink

Jan 1, 1934

By E. E. Barker

ALTHOUGH flotation was known to be a successful process prior to 1912, Utah Copper Co.&apos;s ores were not entirely treated by this process until 1923. Experiments had been conducted, of course, prior to that time, and in February, 1917, the first unit of the Arthur plant was changed over from gravity concentration to flotation. On May 16, 1918, the entire Arthur plant was on flotation, excepting the coarse concentrate which was tabled prior to fine grinding. The reasons for the delay in adopting flotation at these plants were, first, that it was decided to await the outcome of the litigation with the Butte & Superior Mining Co., which began with an injunction served on Oct. 3, 1911. This litigation continued for years. Then the demands on the plants in the war years 1916, 1917 and 1918, really precluded any further drastic changes during that period, as all efforts were bent on maximum tonnage, and the cry of tonnage, rather than of recovery, was the major issue. The postwar depression followed these years of intensive production, so that it was not until 1922 that the Magna plant was equipped to use this process. Excepting, then, the amount of coarse concentrate that was tabled, 1923 was the first year when the Utah Copper Co.&apos;s ores were on, a full flotation basis. EFFECT OF FLOTATION ON ORE RESERVES The object of this paper is to point out the effect that flotation has had on the operations of the Utah Copper Co. In 1905, when D. C. Sackling began making history in copper, the ore reserves were 34,000,000 tons, with a grade of 2 per cent. copper and a mill capacity of 700 tons daily. The point of cut-off between nonprofitable and profitable grades was 1.2 per cent. A few years later the capacity was increased to 6000 tons, when 1.1 per cent became the point of cut-off. Ore reserves had climbed to 80,000,000 tons, having a grade of 1.9 per cent. In 1911 there was an ore reserve of 300,000,000 tons, with a grade of 1.5 per cent and a cut-off of 1 per cent.; in 1918 the ore reserve was approximately 400,000,000 tons, and a grade of 1.38 per cent., and point of cut-off 0.95 per cent., based on normal costs and prices. Up to this

Jan 1, 1928

By William D. Klopp

A study was conducted of the tensile and creep properties of are-melted and electron-beam-melted tungsten over the temperature range 2250° to 4140°F. The tensile and creep strengths vary with pain size, the finer -grained materials being stronger. The activation energy for transient creep at 2250° to 3500°F is 95,000 cal per (g)(mole), while that for steady creep at 3300o to 4000°F is 141,000 cal per (g)(mole). At 2875o to 3300°F the apparent activation energy for steady creep decreased with decreasing temperature. It is suggested that cross slip is rate controlling during transient creep, while dislocation climb is rate controlling during steady creep above 3300° F. ALTHOUGH considerable data have been generated on the high-temperature tensile properties of powder-metallurgy tungsten,1 relative few data have been published on the properties of are-melted2 or electron-beam melted tungsten.3 Furthermore, the available data show a fairly large amount of scatter at high temperatures. The effects of structure and purity have not yet been defined, aside from observations that high-purity electron-beam (EB)-melted tungsten3 and single-crystal-plasma-flame tungsten4 are weaker than less pure powder-metallurgy tungsten. The creep behavior of powder-metallurgy tungsten has been studied, but no data are available on the creep behavior of tungsten consolidated by melting. Green5 found that powder-metallurgy tungsten exhibited linear creep at 4082° to 5072°F with an activation energy of 160,000 cal per (g) (mole). The similarity of this activation energy to that of 153,000 cal per (g)(mole) for volume self-diffusion6 suggests that recovery of strain hardening by dislocation climb is rate controlling in this temperature range. In studies at 4800°F, Sutherland and Klopp7 concluded that grain size significantly affected the creep behavior of commercial powder-metallurgy materials. This grain-size effect was suggested by sherby,8 although the opposite relation had been reported for aluminum.&apos; The purpose of the present study was twofold: first, to provide baseline data on high-temperature tensile and creep properties of are-melted and EB-melted tungsten for concurrent tungsten alloy studies, and, second, to determine the phenomenolo-gical effects of structural and purity variables on the high - temperature mechanical properties of tungsten. EXPERIMENTAL The are-melted tungsten materials were prepared by melting sintered 1-1/4-in.-diam electrodes into 2-1/2-in.-diam by 5-in.-long ingots. The are-melting facility has been described previously.&apos; Eight ingots were melted, machined, and hot-extruded at

Jan 1, 1965

Jan 1, 1881