Search Documents

By B. G. Reisdorf

This paper describes the microstructural changes that occur when quenched ultrahigh-strength steels containing OA pet C and various amounts of nickel, silicon, and cobalt are tempered. The changes that occur in hardness, yield strength, and martensite diffraction-peak widths when these steels are tempered are related to the precipitation of the carbide phases. An unea$ectedly high silicon content (about 30 pct) was found in the E -carbide phase in a steel containing only 1.5 pct Si. TEMPERED martensitic steels have such wide-spread utility that they have been the subject of numerous investigations, and a sizable amount of literature has developed on this subject.M This investigation, which is a part of a larger program to correlate microstructure with mechanical properties at a variety of strength levels, is limited to the microstructural changes that occur when a quenched 0.40 pct carbon steel (USS Airsteel X-200 steel) is tempered, and to the effects of the alloying elements—nickel, cobalt, and silicon—on these microstructures. Used in this investigation were electron microscopy, electron-diffraction identification of the carbide phases, electron-probe micro-analysis of the carbides, X-ray determinations of retained austenite, and measurements of martensite X-ray diffract ion-peak widths. MATERIALS AND METHODS The chemical analyses of the eight heats examined eats No. 30 through 37) are shown in Table L Heat No. 30 has the chemical com~osition of Airsteel X-200, and the remaining seven heats contain various amounts of nickel, chromium, cobalt, and silicon. The heats were air-melted in an induction furnace and cast into 8 by 8 in. ingots that were subsequently heated to 2300 and rolled to 1-in.-thick plate. Oversize 0.505-in.-diam tensile specimens were rough-machined from the plates and austenitized in air at 1700° F for half an hour and oil-quenched. The specimens were then tempered in air at temperatures of 400° to 1000 for tempering times of 1, 4, and 16 hr, and finish-machined to 0.505-in.-diam tensile specimens. Electron micrographs were prepared from Formvar replicas of the midthickness of tensile-specimen shanks that had been electrolytically polished and etched in nital. Electron-diffraction patterns were obtained from carbon-extraction replicas. The replicas were prepared by etching the sample surface in the same manner as for microscopy, evaporating carbon on the etched surface, and re-etching the sample to free the carbon film and the precipitate particles. Electron-probe microanalysis was performed on some of the extraction replicas. To obtain adequate fluorescent X-ray intensities, several thicknesses of replica were exposed to the electron beam so that the results represent an average composition of the extracted particles rather than an analysis of single precipitate particles. The retained austenite contents of the specimens were determined by an empirical X-ray diffraction

Jan 1, 1963

By Aureal T. Cross

THIS paper is a review of the published literature on research in coal geology, principally exclusive of resource studies, which appeared or became available during 1950 and the latter part of 1949. This report is not to be construed as being complete. The papers referred to in the bibliography are those among many more, which were read either in full or in abstract. Undoubtedly other papers were published' which either escaped the author's notice or were not available to him. Those which were seen in abstract only (about one fourth of those listed) were not available in time for the inclusion of more than a notice. An outline of all papers listed in the bibliography has been arranged by subjects and reasonable subdivisions with some papers cited under more than one subject. Most papers are indexed according to the principal subject of discussion or research only as to an unusual or noteworthy section of the entire report. There will likely be some disagreement as to the quality or merit of some of the papers selected and the specialist may be supercritical of the outline or organization of papers in his field. It may be that attention has occasionally been drawn to papers reporting old information or conclusions of questionable value. Conferences and Meetings One of the best indications of the growing interest in coal geology problems in the United States is the increasing number of times this- field has been the focus of attention at conferences and meetings. Notable among these are the joint meeting of the Society of Economic Geologists and the Geological Society of America at El Paso, November 1949, at which the principal thesis was concerned with low rank carbonaceous fuel deposits, especially of western United States. Among the papers given which are already available were those presented by Barghoorn,16 Parry,180 Roe,153 and Parks.162 At the annual meeting of the Botanical Society of America in New York, December 1949, a joint meeting of the Paleobotanical and Microbiological Sections was held for which a symposium on Microbiology in Relation to the Geologic Accumulation of Organic Complexes was 'organized. Publication of the six papers presented by Ralph G. H. Siu, Elso S. Barghoorn, Irving Breger, Claude E. ZoBell, James M. Schopf, and A. C. Thayson is anticipated. At the regular meetings of the Paleobotanical Section at the same time, several other papers of interest reported on coal ball studies, partial coalification of petrified wood, and floras. In Chicago, April 1950, a symposium on Applied Paleobotany was held by the Society of Economic Paleontologists and Mineralogists in conjunction with the American Association of Petroleum Geologists. The five papers presented at this meeting dealt with the use of Paleozoic plant microfossils for stratigraphic work, J: M. Schopf, Devonian-Mississippian fossils of the black shales, Aureal T. Cross, Mesozoic plants of stratigraphic value, Th. Just, plant microfossils of the Tertiary, L. R. Wilson, and studies of the Brandon lignite, Elso S. Barghoorn. Early publication of these in the Journal of Paleontology is expected. The Nova Scotia Research Foundation and the Nova Scotia Dept. of Mines sponsored an excellent 3-day conference in June 1950, which, dealt with several aspects of coal geology. Papers on coal classification, P. A. Hacquenbard, structure and sedimentation problems in Nova Scotia, T. B. Haites, new techniques of thermal analysis, W. L. Whitehead, geochemical investigations of Nova Scotia coals, Irving Breger, the role of fossil plant spores in coal correlation and the stratigraphy of the coal-bearing strata of the Appalachian Region, Aureal T. Cross, were given. Some discussions of these papers by those in attendance were recorded, and the entire proceedings is being prepared for publication. In September 1950, an unusual 3-day field conference was held by the Ohio and West Virginia Geological Surveys under the sponsorship of the Coal Geology Committee. This study of the stratigraphy sedimentation, and nomenclature of the Upper Pennsylvanian and Permian coal-bearing strata of southeastern Ohio, southwestern Pennsylvania, and northern West Virginia .was augmented by two discussions on associated rocks (clays and shales) and stratigraphic nomenclature at Wheeling, and Morgantown, West Va. An extensive guidebook was prepared, and transcriptions of the Morgantown meeting were made. As a follow-up of the September field conference, a round-table discussion 'was held on this general topic at a special open meeting of the Coal Research Committee in conjunction with the November meeting of the Geological Society in Washington. Short prepared statements to invite discussion were given on each of several topics by L. M. Cline, Carl O.

Jan 1, 1952

By D. J. Weintritt, J. C. Cowan

Methods of studying oilfield mineral .scale deposition in the laboratory do not work for barium sulfate because only small nonadhering crystals ore formed. On the other hand, barium sulfate scale found in down-hole or surface equipment is strongly adhering and may contain very large crystals. Results suggest that most of the difference derives from the extremely low .solubility of barium sulfate. Firm adherence of scale and the consistent development of oriented crystals 100 microns and larger suggest a relationship between scale adherence and crysta1 growth. Data from this study indicate some reasons for barium sulfate's occurring as a deposit in oilfield waters. The unique characteristics as well as the associative properties of barium sulfate scale as related to calcium carbonate and calcium sulfate ere shown. INTRODUCTION The first observed deposition of barium sulfate scale in oilfield production equipment is unknown but probably coincides closely with the beginnings of the oil industry itself. Moore' described barite oolites in some producing wells in the Saratoga field, Tex., in 1914. Currently, positive identification of barium sulfate deposition is recorded in most of the major oil-producing areas of the United States. As efforts continue to identify the composition and functions of the materials found in scale deposits, the geographic and economic importance of the part played by barium sulfate will become even more important. This belief is based on the following Facts. 1. Many oil fields in the U.S. are in or entering their mature phase and the volume of produced water is increasing; thus, the cumulative effects of low-solubility minerals become more significant. 2. Secondary recovery techniques and increased emphasis on waste disposal systems require controlling the behavior of all constituents of water to prevent formation plugging. 3. The more general use of instrumental analysis has reduced the time and improved the accuracy of complete scale and water analysis. 4. Once formed, barium sulfate scale is resistant to present methods of chemical removal; therefore, costly mechanical methods are necessary. Thus, new methods of prevention and control will require specialized chemical techniques and better knowledge of the causes of scaling. Consider the results of some simulated field deposition studies illustrating this need (Fig. 1). The studies utilized a Scale Deposition Test Cell* and each coupon was exposed to 8,000 ml of a 300 me/liter solution of the various types of mineral scale. All tests were conducted at 140F. Only the calcium sulfate and calcium carbonate deposited scale. The solution containing 300 me/liter of barium sulfate exhibited copious amounts of precipitate, but none of the precipitate adhered. The fluids from the effluents were also allowed to impinge on glass slides. Fig. 1 shows the relative adherence of the three types of scale on unetched glass. The barium sulfate failed to deposit in the same manner as the calcium carbonate and calcium sulfate solutions.

By Charles M. Romanowitz

The motivation for the art of dredging for placer mining can be compared in a slight degree to the spread of civilization which started in the Near East and spread both east and west. Dredging started with the "bag and spoon" dredge in the lowlands of Europe reportedly about 1565, went southeast to New Zealand where designs were developed for a bucket-line mining dredge known as the New Zealand type, and westward to the eastern United States where a dredge was developed and used exclusively for excavating. Then it moved to Montana, where it was first used for mining in 1895. The New Zealand-type dredge was imported into California in 1898 (Fig. 1) and was followed shortly by the Montana design. As today, these early dredges were equipped with continuous bucket- line chains, a treatment plant, and a means of waste disposal mounted on a wooden hull. Both types of dredges are complete mining units: they dig the formation, transport the dug materials, and concentrate the valuable ore. After sizing, the fines containing the ore are passed by gravity to the treatment unit, while the barren materials are discharged overboard. By digging the materials to be treated at the bow and depositing all the waste, at the stern, the dredges automatically advance to new reserves without presenting any transportation problems. The main differences between the two types are in the method of holding the dredge in the digging position and in the disposal of the tailings to the rear. The New Zealand type (Fig. 2) uses the headline system with a bow anchor for holding the dredge in the digging position and long tailing flumes or short stackers off the stern for disposal of the barren materials. The California type (Fig. 3) uses box girder spuds projecting into the ground in a vertical position at the stern of the

Jan 1, 1969

By B. Silliman

THE remarkable outflow of natural gas recently developed in Western Pennsylvania, and along the valley of the Ohio and its tributaries, has called attention to an important series of patents for improvements in glass-fnrnaces and the manufacture of glass, which the brothers Siemens have made since 1872. The basement-patent of this series, is No. 127,806 of the U. S. Patent office, and is of date June 11th, 1872. This has been followed by eleven other patents (including one re-issue), all for improvements in glass-furnaces, or methods of manufacture, of which the latest is of date July 11th, 1882. Nine of these patents were issued in 1880-82. The following is the list of these patents, in order of dates, viz.: 1872. June 11th. No. 127,806 (U. S. office), Improvement in glass-furnaces; 17 sheets drawings, 5 pages text. This is the basement-patent. 1877. April 17th. No. 139,800. Improvement in the manufacture of glass; 3 sheets drawings, 2 pages text. Boats and floating vessels swimming in the liquid glass of the tank-furnace. Re-issued in 1880. q. v. 1880. April 27th. No. 226,931. Furnace for annealing and tem pering glass. " July 13th. No. 220,846. Glass-melting-furnace. " August 3d. No. 230,668. Glass-melting-furnace; 4 sheets drawings, 2 pages text.

Jan 1, 1885

By J. W. Rutter, K. T. Aust

The temperature dependence of the rate of grain boundary migration was measured in bicrystals of zone-refined lead containing from 20 to less than 1 ppm by wezght of tin. The apparent activation energy in the temperature range from 320" to 200oC is markedly dependent upon the solute tin concentration and upon the orientation relationship of the grains adjacent to the grain boundavy. The quantitative experimental observat~ons are compared with the predictions of various theories of grain boundary migration. In previous work.&apos;?&apos; the mobility of individual grain boundaries was studied as a function of impurity concentration and type of boundary. Grain boundary migration occurred at the expense of dislocation arrays which were introduced into the specimen during solidification. Boundary mobility in zone-refined lead at 300°C was markedly decreased by small additions of tin. 0.004 wt pct being sufficient to decrease the rate of grain boundary migration by a factor of 1000. The mobility of grain boundaries having polar orientation relationships near 38 and 22 deg about <Ill>, and 28 deg about <100>, was much less sensitive to tin concentration in the range studied. As a result, these boundaries have relatively high mobilities. The present paper is a continuation of the above study. Data are now presented on the temperature dependence of the motion of individual grain boundaries in zone-refined lead as a function of solute tin concentration and orientation relationship of adjacent grains at the grain boundary. The experimental observations are compared with the predictions of a number of theories of grain boundary migration3-8 which, prior to the present experimental investigation, could not be critically evaluated. EXPERIMENTAL PROCEDURE The striation or lineage structure of melt-grown single crystals of zone-refined lead, containing various additions of tin, was utilized to provide a driving force for grain boundary migration, as previously described.1,2 Each grain boundary under study separated the striated single crystal from another grain which was introduced by localized plastic deformation and recrystallization of a small region of the sample. The speed of migration of grain boundaries in dilute alloys of tin in zone-refined lead was investigated as a function of 1) tin concentration from < 0.0001 to 0.002 wt pct, 2) temperature in the range of 200" to 320°C, and 3) orientation relationship of the adjacent grains at the grain boundary. The substructure driving energy available for grain boundary migration was estimated to be about 4000 ergs per cu cm, within a factor of two, from specimen to specimen.&apos; The specimen dimensions, and growth and alloying procedures for the preparation of striated single crystals of lead of known tin composition, were as described previously.&apos; Each bicrystal was carefully wrapped in aluminum foil, and annealed in a well-stirred salt bath consisting of 50 pct NaNO2 and 50 pct KNO3, for known periods of time at a series of constant temperatures (*2°C). The grain boundary positions, before and after each anneal, were determined by etching lightly in a solution of 5 pct nitric acid in methyl alcohol, in order to follow the motion of the boundary and determine its rate of migration. Thus, the rate of motion of the grain boundary in a single specimen was measured at various temperatures. The above procedure was carried out for each grain boundary in seventeen different bicrystal specimens.

Jan 1, 1960

By L. T. Sicka, H. N. Thomson

The Tooele plant of the Internationa1 Smelting & Refining Co. is situated at the mouth of Pine canyon, Tooele county, Utah. It is connected with the main line of the San Pedro, Los Angeles & Salt Lake railroad by the Tooele Valley railway, and is about 7 miles from Tooele Junction. Fig. 1 is a general view of the plant. The copper plant has been in operation since July, 1910, arid the first blast furnace at the lead plant was blown in on Feb. 29, 1912. The location of the plant was selected on sloping ground with the idea of using gravity to the fullest extent and thus keeping labor at a minimum. Practically the entire plant is constructed of steel, reinforced concrete, and brick. Bingham ores, both lead and copper, are received over the Utah Consolidated Aerial Tramway. The tram buckets, each containing

Jan 1, 1914

NEW MEMBERS The following list comprises the names of those persons who became members during the period Apr. 10 to May 10, 1915: Members ADMAN, WILLIAM, Supt., Susquehanna Coal Co Lykens, Pa. BARTH, CARL G., JR., Min. Engr 6151 Columbia Ave., Philadelphia, Pa. BOOTH, ERIC EDWIN, Min. Engr., Mount Elliott Mine, Selwyn via Cloncurry, North Queensland, Australia. BOYDELL, HARRY CYRIL, Asst. Mgr., Randfontein Central Gold Min. Co., Box 42, Randfontein, Transvaal, South Africa. BRADY, SAMUEL HOWARD, Mine Supt Bohemian Club, .San Francisco, Cal. Buses, HARRY EDWARD, Mine Supt., Engels Copper MiningCo Keddie, Cal.

Jan 6, 1915

Jan 1, 1896

By Yap Chu-Phay

IN 1923, when the writer began his studies in metallurgy, he came upon an article by Professor Honda on the, Equilibrium Diagram of the Iron-carbon System, 1 which made a profound impression on him. What interested him most was this sentence: "In the recent diagram of the iron-carbon system, the solidus is usually shown as a curve bending considerably downward. But it can be shown by thermodynamics that if the liquidus is straight or slightly curved, the same must also be true for the solidus. Hence, in my constitutional diagram, the lower portion of the solidus is slightly bent upward." Ever since then the writer has been interested in thermodynamics, especially chemical thermodynamics. The applications of thermo-dynamics to the metallic systems have been, in the writer&apos;s opinion, sadly neglected, although we continually use the phase rule in our study of equilibria in the liquid and solid states of metallic alloys. Many investigators, among whom may be mentioned Heycock and Neville, and s Honda and his coworkers, have applied the simple Raoult-van&apos;t Hoff law of depression of freezing point, mainly to determine the heat of fusion, but no attempt has been made to investigate the applicability of the thermo-dynamic laws of solution (as opposed to the laws of solution derived from other sources) to metallic systems" showing either limited or complete solid solutions. Perhaps the reason for this neglect is that until recently there have been so few reliable data on the solidus, which is much more difficult to determine than the liquidus. The writer has under way at the present time an investigation of a number of systems, the solidi of which have been more or less reliably determined. Recently, the writer has not only shown the valid applicability of the thermodynamic laws of solution as applied to the system antimony-bismuth but has also suggested a method of attacking problems involving complete and incomplete equilibria.2 In the present paper, the same method of approach is employed. For convenience, we shall divide this paper into two parts:

Jan 1, 1931

By David R. Mitchell, Byron M. Bird

THE revision of this chapter has presented a problem in that heavy-medium jigging has come into the picture since the chapter was originally written (seven years ago), a practice in which an artificial medium is built up and maintained in the jig circuit. As this development makes the jig a "true" heavy-medium process, the method belongs in the chapter dealing with such processes. Although putting this development in its proper position in the book involves some repetition, this seems to be the best procedure, and it has been followed. As the chapter on jigs in its original form was intended to be more or less a handbook on jigging for the use of the practical man, and the great bulk of the material therein is still generally applicable, the text has been re-used in large measure. Two major changes should be noted: (1) the portion of the text relating to the refuse-withdrawing mechanism of the McNally-Pittsburg jig has been entirely rewritten, and (2) a description of the hutch valves on the Jeffrey jigs has been added. Jigging is the stratification of a mass of solid particles in upward and downward pulsations. The stratification usually is effected in a rectangular open-top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (2) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through 3/4-in. to 0, and mixed sizes of ores down to 7/32-in. to 0and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 per cent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems.

Jan 1, 1950

By J. W. Hickman, E. A. Gulbransen

In a previous paper&apos; the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300&apos; to 7o0°C. except for copper, wherc the range selected was 100&apos; to 500°C. The results of these studies were presented in graphical form as existence diagrams of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviatiois in lattice Darameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: 1. The existence diagrams of various alloys. 2. The effect of the structure of the alloying metal on the existence diagram of iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body-centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K4²B, Nichrome V, Hipernik, Inconel, Stellite "²I," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

In a previous paper&apos; the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300&apos; to 7o0°C. except for copper, wherc the range selected was 100&apos; to 500°C. The results of these studies were presented in graphical form as existence diagrams of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviatiois in lattice Darameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: 1. The existence diagrams of various alloys. 2. The effect of the structure of the alloying metal on the existence diagram of iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body-centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K4²B, Nichrome V, Hipernik, Inconel, Stellite "²I," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1947

By R. F. Lynch, J. D. Wood

The Al-1.0 pct Mg alloy 565 7 was studied using optical microscopy and electron microprobe X-ray analysis. Constituent particles were found to exist inter-dendritically in the as-cast material in a region of precipitate free a -aluminum. Five phases besides a fine precipitate and a-Al were identified in the cast structure: Fel3, Fe2Al7, Mg2Al3, CUMgAl2, and Cu2FeAl7. Thermal treatments conducted for 100 hr at 1180°, 1130°, 1080°, 1030°, 980°, and 880° F revealed a general dissolution and spheroidization of the in-terdendritic constituent network observed in the cast structure. The principal constituents present in the thermally treated structures were FeAl3 and Fe2Al7 with the relative amount of Fe2A17 to FeAl3 increasing with a decrease in the treatment temperature. The phases Present in the wrought structure were identical to those observed after the thermal treatments, with the constituent particles strung out in the direction of rolling. ALLOY 5657 is a nonheat-treatable commercial purity Al-1.0 pct Mg alloy utilized extensively because of its bright finishing characteristics. This investigation was conducted to determine the constituents present in 5657 alloy, and to study the effect of extended thermal treatments on morphology. Numerous studies have been carried out to establish the equilibrium diagrams for various aluminum systems,1-3 with phase identification based on X-ray analysis, morphology, and the etching response of relatively large particles. Phragmen4 conducted a study of the phases in aluminum eutectic systems and compiled a "corrected" table of etching responses, drawing on his work plus that of Schrader,5 Keller and Wilcox,6 and Mondolfo.7 A review of the original work of Keller and Wilcox, and Mondolfo, which was concerned with the constituents found in commercial alloys, reveals that in numerous cases their etching responses differ from those reported by Phragmen and from each other. These inconsistencies may occur because a specific constituent will react to a given etch in a varying manner depending upon its size, the elements dissolved in the phase, the other constituents surrounding a phase, and the solute content of the matrix. Work with a commercial orientation was conducted on alloys 2024 and 3003 by Sperry8,9 and on alloy 3003 by Barker,10 where the relationship between the phase diagram and the nonequilibrium structure of an alloy was examined. Backerud11 investigated the A1-Fe binary system and found that at high cooling rates the equilibrium eutectic reaction forming a-A1 and FeA13 is replaced by another lower temperature eutectic reaction forming a-A1 and metastable FeAl6, a constituent first identified by Hollingsworth et al.12 Most of the above mentioned studies were conducted on materials having a significantly greater alloy content than 5657 alloy, where the relatively small size and sparse distribution of second phase particles hinders the process of identifying constituents. EXPERIMENTAL PROCEDURE Material with a composition as given in Table I was examined in the as-direct chill cast, hot rolled and cold rolled conditions, and after thermal treatment of the cast structure. Thermal treatments were terminated by a water quench. Microscopic examination was conducted under various lighting conditions following the application of standard etchants as specified in Table 11. A semi-quantitative electron microprobe X-ray analysis was conducted for Al, Mg, Fe, Cu, Si, Zn, and Ti. RESULTS AND DISCUSSION Microstructure of the As-Cast Material. Particles of second phase material were found to exist inter-dendritically, principally in regions of precipitate free a-Al, as illustrated in Fig. 1. Adjacent to the ingot edge was a region of inverse segregation, resulting in an increased amount of second phase material containing large sized particles which aided in phase identification. Phase Identification. Cast Structure. Five phases besides a-Al and a fine precipitate were identified using optical microscopy and electron microprobe X-ray analysis, as presented in Tables II and III, respectively. FeA13 and Fe2A17 are often found with Fe2A17 forming a sheath around the core of FeAl3, resulting from an incomplete peritectoid reaction. These phases have a nearly identical appearance under white light, although they are easily differentiated under crossed polarizers, as characteristically illustrated in Figs. 2(a) and 2(b), respectively. Microprobe analysis con-

Jan 1, 1970

By James G. Blaine, David A. Summers, L. John Tyler

There has been a considerable amount of research developed which shows that the close contour cutting of an excavation prior to removal of the central core will increase ground stability while concommitantly, reducing the number and size of blastholes required to create the excavation. To date, the industrial development of this technique has however, centered on the development of equipment based on simple cutter movement and mechanical rock cutting. The advent of reliable field operable high pressure waterjet cutting equipment with the very low reactive force required to hold the head in position has opened the way for a much smaller and more manueverable system. The advent of small, micro-computers allows the programming of accurate profiles for cutting tools on excavation equipment. The combination of these two technologies will allow the generation of complex as well as simple, excavation profiles and lead to the potential pre-support of the opening before major excavation is completed. A brief description of the necessary components and their functions is encorporated in the initial prototype design as given.

Jan 1, 1984

By Henry M. Howe

The object of the present paper is to suggest injecting into the hearths of iron blast furnaces, whose temperature has become unduly lowered, some form of fuel whose calorific intensity, under the peculiar conditions existing there, is considerably higher than than of liquid petroleum, the rose of this substance for melting out chills having grievonsly disappointed the high hopes which were at first entertained of it. A chill being a fall of the temperature below that needed for the complete liquefaction of the slag, which requires, according to Plattner, about 1800&apos; C., one would suppose that the chief thing to be accomplished in curing it would be to raise the temperature in the crucible of the furnace. The most obvious ways of doing this seem to be to raise the temperature of the blast, and to increase the amount of fuel in the crucible itself. Simply increasing the rate at which the blast enters the furnace, if carried beyond a certain point, should lower the temperature in the crucible. The existence of a chill shows that the fuel is arriving too slowly at the tuyeres. If air be introduced so rapidly as to he in excess of that required for the combustion of the fuel, all that excess will simply lower the temperature around the tuyeres, carrying the region of intense heat upwards, and weakening its intensity by increasing its size. Up to a certain point, increasing the rate of introducing the blast will increase practically pari passu the rate at which the fuel reaches the tuyeres. But when mechanical obstructions, which so often accompany chills, retard the descent of the fuel, there must be a point beyond which this does not hold good, and beyond which farther

Jan 1, 1883

By H. I. Aaronson, H. A. Domian, G. M. Pound

Zener&apos;s two-parameter theory of the y a reaction in Fe-X alloys is extended to encornpass austenite-stabilizing as well as fewite-stabilizing elements, and is then cottzbitzed with statistical thermodynamic theories of Fe-C alloys to permit development of a ther-modynamic description of the proeutectoid fewite reaction in Fe-C-X alloys. Equilibrium tielines are calculated for tile a + y rep&apos;on from experimental data and frort extrapolations of the y/y +a equilibrium surface. Sectzovs of the y/y + 0 surface are calculaled for the tzetastable sstuation LYL u-kich alloyrtg eleitzents do not partition betzseen azrstenite andfer-rite. The finding that the metastable y/a + y curves Lie close to their equilibriuwz counterparts when X = Si, .Vo, Co, Al, and Cu but well below them when X = A/ln or Ari pr-elides a thermodunamic explanation for the expcri1?7e?ztally obserted absence of partition during the proeutec toid ferrite reartlon in the fortner alloys and for the occurrence of partition at hzgher ternperatures in the latter alloys. Cotarison ofno- patitzoa free-energy changes and y/y i a curr,es in Fe-C-X alloys with the equilibrium 11al1es of these quantities in Fe-C alloys furnishes additional qualitative insight into the irqluence of allojling elements upon the kinetics of the proeutectoicl ferrite reaction. THE introduction of a substitutional alloying element, X, appreciably complicates calculation of the thermodynamics of the formation of proeutectoid ferrite from austenite. As noted in the preceding paper,&apos; the positional entropy of the interstitial species is the principal component of the free energy of an interstitial solid solution with which theory has so far been able to deal. One would expect, however, that other components of the free energy of this type of solid solution may be significantly altered by the addition of a substitutional alloying element. Even if the assumptions are made, by analogy to the case of Fe-C alloys,&apos; that changes in the positional entropy of carbon represent a significant part of the thermodynamic effects of an alloying element, and that the remaining effects can be taken into account by fitting the equations developed on this basis to experimental data on Fe-C-X phase diagrams or on the activities of carbon in alloyed austenite and ferrite, the experimental information available on either of these quantities is not yet sufficiently accurate or extensive, respectively, to make such an approach useful. An attempt made by Zener on the former basis to explain the effects of alloying elements on the thermodynamics of Fe-C alloys in terms of a temperature-independent "free-energy change" (actually enthalpy hane&apos;) required to transfer 1 mole of an alloying element from austenite to ferrite, in which the "free-energy change" was determined by fitting the theoretical relationships developed to Fe-C-X phase diagrams, thus proved inadequate in part because of deficiencies in the available ternary-phase-diagram data.= Other difficulties of a more fundamental nature, however, also indicated the desirability of a different approach to the problem.3y4y6 zener6 subsequently proposed that the free-energy change associated with y — a transformation in pure iron can be decomposed into magnetic and nonmagnetic components. Alloying elements were assumed to affect those components separately. One parameter was used to describe the quantitative effect exerted on each component. These parameters were evaluated from Ms (martensite-start) temperature data and from other experimental information usually either readily available or measurable with acceptable accuracy. Zener applied this treatment only to the calculation of Fe-X phase diagrams in which X is a ferrite-stabilizing element. In the present study, this treatment is extended to include austenite-stabilizing elements, and then combined with treatments previously considered for Fe-C alloys1 to permit calculation of the thermodynamic quantities of interest in the austenite - proeutectoid ferrite transformation in Fe-C-X alloys, where a number of representative, and commonly used alloying elements are chosen for X, including Si, Mn, Co, Mo, Al, Cr, and Cu. The results are used to explain important features of the partition of alloying elements between austenite and proeutectoid ferrite, as reported in a companion paper7 on the basis of electron-probe analysis, and to provide some additional understanding of the influence of alloying elements upon the kinetics of nucleation and growth of proeutectoid ferrite. Portions of this treatment6 have been clarified in the course of a review by Kaufman and Cohen.3 The consolidated summary of these developments with which this section is begun provides a basis for further clarification of the treatment, from which extension to include austenite- as well as ferrite-stabilizing elements is a natural consequence. The division of the free-energy change associated with the 7 - a transformation in pure iron, into two independent components is formally stated as:

Jan 1, 1967

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson&apos;s discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 7 3/4 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612° F. (322° C.), they reduced the 7 3/4 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statement just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson&apos;s time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced consumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opinions advanced by different authorities in the scientific world to account for the apparent anomaly, but none,

Jan 1, 1877

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson&apos;s discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 79 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612&apos; F. (322&apos; C.), they redoccd the 79 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statenlent just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson&apos;s time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totsally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced colisumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opirlions advanced by different authorities in the scientific world to account for the apparent anomaly, bat none,

By John Hall

THE Fremont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about 3/8 by 1/4 by about 1 1/4 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Fremont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. I this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions. .

Jan 7, 1913