Search Documents

By K. Huessener

In presenting the following data on combustion in the open hearth furnace and the advisability of automatic combusion control, the author finds himself much more severely handicapped by the lack of reliable test results than he had anticipated when he first undertook to write this paper. In order thoroughly to investigate how the results of an open-hearth furnace are influenced by combustion, one would have to draw up a large number of heat-balance sheets, as Kinney and McDermottl have given for one heat in their extremely able paper on "Open Hearth Efficiency,' presented before the American Iron and Steel Institute on October 27th,1 1922. Instead of covering only one heat, however, such heat-balance sheets would have to embrace a large number of heats, and not only for one kind of fuel, but for all the various fuels in customary use. Use of Radiation-protected Pyrometer Such tests necessitate extremely careful temperature readings, and here the first serious difficulty presents itself. Nearly all the temperature readings so far published have been taken with thermocouples for the lower ranges and with optical or radiation pyrometers for the higher ranges. This method of measuring reveals the temperature of the surrounding walls, or in the case of optical or radiation measurements, the temperature of that part of the opposing walls which has been focused by the instrument. The error in ascertaining the temperature of the gases entering or the waste gases leaving the checker chambers is probably not very large, as the flowing gases impart their temperature to the walls of the flues. On the other hand, the uptakes, where the preheat temperature of gas and air are usually measured, are under the influence of radiated heat from the port ends, and correct temperature readings can here be taken only by using a radiation-protected pyrometer of the aspirating type.

Jan 1, 1926

Jan 4, 1951

By W. Kennedy

THROUGHOUT northeastern Texas we have an extensive series of iron-ore deposits, occupying portions of nineteen counties and having approximately an actual ore-covered area of 1000 square miles. The existence of these ores has long been known. Kennedy* says: "Iron-ore is distributed in profusion throughout Texas, being found almost everywhere except in the level region of the coast." Before this, C. Newell† had mentioned the existence of these ores thus: " Iron is found in abundance in the eastern, northern and middle portions of Texas;" and in 1849 Edward Smith‡ said: " We met with immense hills of iron which were said to be, and appeared to be, of excellent quality, in Cass and Titus counties.. . .. It is well known that Texas abounds with iron of first-rate quality." In 1859, Dr. Shumard? reports that detailed surveys had been made in several counties, and says: " Our labors have demonstrated the important fact that we have a vast iron-region in the eastern part of the state, embracing considerable areas in Cass, Harrison, Rusk, Panola, Smith, San Augustine and Shelby counties. The ore-deposits belong to the Tertiary era and consist chiefly of hematites and limonites, of which there are several varieties. We have also found in this district extensive beds of carbonate of iron." Dr. Shumard gives no very exaggerated description of Cass county§ as it then existed when he says : " Cass county alone is capable of supplying a number of furnaces with an abundance of excellent iron-ore for many years." Of Rusk county he says: "Our de-

Jan 1, 1895

By F. C. Stanford

THE work of an engineer is to direct natural forces so that they bring about the results that he wishes to secure. Heretofore he has concerned himself chiefly with physical forces and inanimate objects, until he has secured a truly marvelous degree of control over them. The great problem of the present age is to secure a like degree of knowledge and control of the human factor. Progress has already been made along this line, but, it is only a beginning. Wilhelm Ostwald says that scientific knowledge enables a man to be a true prophet; but it must be remembered that a good many people do not seem to be able to maintain a high average in prophecy. In short, the average of knowledge is not equal to the average needs of the present time, but continually fails to keep pace with it. It has been aptly said that the really essential need of the period is for more brains; if we only had sufficient knowledge and sagacity we could not only solve all difficulties, but prevent them from arising. This generalization holds good for an industrial organization. The most vital need of the management is for more brains. The logical course for an engineer in charge of an industrial organization is, therefore, to direct whatever forces may be at his command toward the development, training, and guiding of all the brains in his organization. This is easier said than clone, for it involves the carrying on toward two objectives, the maximum of productive work, and the development of the individuals who perform it. This is essentially like the rebuilding and enlarging of a plant, keeping it in full operation the while. On the other hand, if the aim is merely for maximum production from an organization, without offering opportunity for development, the final outcome will necessarily be like that f a plant that is driven at full capacity without stopping for repairs or improvements; it eventually becomes so run down that either a complete rebuilding is necessary or else it has to be abandoned.

Jan 2, 1918

By A. U. Seybolt

The pressure-temperature relations required to maintain the existence of Si3N4 in silicon-iron of 0.44-11.7 pet Si have been partially explored. The critical data obtained have allowed the calculation of some thermodynamic quantities, and have shown evidence of an order-disorder two-phase field extending at 800°C from about l pet to 5.5 pet Si. THE presence of silicon nitride in electrical sheet, nominally about 3 1/4 pet silicon, balance iron, has been described by several authors'" but there has been some discrepancy among them regarding the identity of the nitride. Also, little has been reported on the quantitative thermodynamic prop- erties. In the work to be reported here, the nitride has been found to be more stable than described by Corney and Turkdogan." Several silicon nitrides have been described in the past, including SiN, Si3N4 and Si2N4 (see, for example, Abegg6 and Pascal7). However, the literature on nitrides other than Si,N, is all very old. No recent investigators using the more powerful tools available today have reported the presence of any nitride other than S3,N4. W. B. Hicke and L. R. Brantley8 in 1930 determined the dissociation pressure of Si3N4 which they made by reacting nitrogen

Jan 1, 1959

With one shaft almost completed and another shaft being sunk, the scope of the Saskatchewan potash area is beginning to come into focus. Some 18 companies have reportedly leased more than four million acres to explore potash possibilities. PCA, farthest along, is located about 15 miles southeast of Saskatoon, and IMC has its project underway near Esterhazy in the eastern edge of the province. U. S. Borax and Chemical Corp. is also reported exploring the area. The field lies in the middle Devonian geological formation which was probed by oil companies along the 200-mile area across the province. Extensive examination began after World War II and deep drilling was started a few years later.

Jan 5, 1958

By Granville S. Borden

TAXES in general are onerous and are not a pleas- ant subject for discourse. There are, however, some very cogent reasons why we should dedicate a part of our thoughts and services to the solution of our taxation problems: The happiness of every individual in the United States depends on the maintenance of a stable government. The collection of taxes is an indispensable function of a stable government, and the power to collect taxes depends in part on the question whether taxes are fair and equitable. As representatives of the mining industry it is our duty to .protect it from tax burdens that are discriminatory or- unjust, As citizens we find that taxation is incessantly endeavouring to unravel the knots in our purse-strings. Many members of the Institute may be consulted .by clients on taxation problems, especially the phases which re- late to depletion and valuation. It is the hope of the writer that the discussion of some of the current depletion and valuation problems will stimulate interest in the problems, and as a consequence of this new interest facts will be ventilated, opinions rendered and services performed, which will be a means of solving the problems to the satisfaction of all parties interested.

Jan 1, 1929

By Tony B. Szwilski, K. Unrug

INTRODUCTION Since the introduction of longwall coal mining systems, reliable predictions of roof support requirements at the face and the roof caveability in the gob area have been major contributors to the success of the longwall face by means of safety and face productivity. That is, the successful operation of a longwall is well-served by good regular caving of the gob. In recent times, with the advent of increased coal face mechanization and capital investment, the evaluation of the feasibility of longwall mining has become essential. In the United States, where a face unit for a face length of about 150 metres may cost around $6 million, a quantitative system that would assist in selecting the best equipment for the coal would prove extremely beneficial. There have been many such varied investigations in the past few years. A vast -amount of work has been invested principally by West Germany [3, 7, 8, 91 , Poland [I, 101 , United Kingdom [4, 5, lo], France [4], and South Africa [4]. It is the object of this paper to review this previous research work and give an outline that may be used as guidelines for long- wall evaluation. Essentially, for the initial design phase for a longwall system, account must be taken of the geometry of the coal panel, its position relative to the surface (depth), direction of the coal cleat system, faults and in-situ stresses and other neighboring workings in the same coal seam and other seams both above and below. The advance of the coal panel disturbs the stress field and in doing so creates an abutment zone around the face. At this stage the condition of homogeneity of the surrounding rock mass does not apply. The magnitude of the rock strata pressure may exceed the ultimate strength of the rocks and create zones of clastic, plastic and elastic material, the limits of which are difficult to determine. The collapse of the gob and resulting expansion of the displaced waste roof rock, create a statically undefined support complicating an already unclear rock structure. For example, it is often a point of debate whether, indeed, the vertical strata pressure develops to regain the original magnitude of virgin stress. Under these post-failure circumstances an analytical approach based on simplified and idealized assumptions can only be considered a very general approximation. Theoretical concepts, however, may be adequately supplemented by empirical methods that are based on numerous underground observations and surveys [3, 4, 7, 8]. These methods employ the use of rock indices that very handily correspond to the competence of the roof rock mass. Scale model work [3, 41 , using equivalent materials representing the surrounding rock mass within the coal seam zone, have given valuable qualitative and sometimes quantitative data in addressing the behaviour of the rock mass around longwall panels. To characterize the state of art of caveability predictioqthe principal concepts will be reviewed with special emphasis placed on practicality for the planning of longwall operation. It has been the general observation of the authors that many of the literature surveys published in English often neglect reference to other international mining literature. It is with this point in mind that an overall review has been written including mining concepts identified with the principal coal mining countries. THEORETICAL CONCEPTS Arching Theory For the development of this theory, assumption has been made that an extracted height, h, in a coal seam results in an extracted panel of width, w . Also, the coal seam is horizontal and the rock strata of both the roof and floor are homogeneous. The primary (virgin) stress distribution will change in the roof as well as the floor. As a result of lack of support caused by the excavation (in the gob area) an additional load is developed due to the redistribution of the load around the sides of the panel, referred to as the abutment, R, where: [ ]

Jan 1, 1982

By S. R. du Toit, W. J. Oberholzer, M. I. Watson, D. G. Krige

The objectives, essential features and implications of the 'random' and 'deterministic' types of ore value surfaces are examined as well as the basic requirements for a satisfactory prediction model. The 'random' method used on the South African gold mines and based on observed auto-covariance patterns is briefly discussed as well as its justification in preference to the 'deterministic' approach. Various mathematical models for auto-covariance patterns are examined for the one-dimensional case. It is also shown that these patterns as estimated for ore values in certain mines agree closely for various sizes of ore unit. In two case studies the variations in gold, uranium and ore thickness covariance patterns are examined and compared with certain geological features established independently from sedimentological studies.

Jan 1, 1969

By Hugh Henton

THIS paper is the result of an investigation made in association with Dr. Charles H. Fulton. Early in 1918 a search was started for methods of utilizing, in the manufacture of basic refractories, certain domestic resources in magnesites, dolomites, and magnesian limestones. Much information was collected during that year and during 1919 regarding magnesite and dolomite deposits. During 1920 and 1921 a research was made into methods of calcining dolomite and separating magnesia therefrom. Some success was attained and many new ideas were brought out in connection with the preparation and utilization of magnesia in the form of "caustic" or light-burned material as well as in the form of refractory or "dead-burned" material. Stimulated by this success, much advance has been made in manufacturing processes for the "plastic magnesia," so called, used for magnesia cement, stucco, flooring and otherwise in the structural industries.

Jan 3, 1926

Jan 1, 1923

By Robert Franke

(Butte Meeting, August, 1915.) IN view of the prominence which the conical mill has attained in the fine-crushing field within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the imme diately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years' operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which follow rolls crushing to 0.5 in.

Jan 7, 1913

By R. K. Hopkins

For a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not with-stand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950° to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as -75° F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these require-ments, but as a result of the extensive research carried on by steel manu-facturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service.

Jan 1, 1935

By J. A. Collins

THE process of plastic extension of face-centered cubic single crystal-line rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellae are free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [112] direction in the axis of the rod. This process has been checked in many face-centered cubic materials and readily permits the preparation of specimens that have been sub-jected to various determinable amounts of shearing action. It is clearly of interest to study in such measurably strained specimens the development of a recrystallized structure on annealing and if possible detect the source of nuclei from which the new crystals grow. Strain-annealing experiments of this character have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs, the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae) at the conclusion of a test of from 0.08 to 0.57. A particular point was made of determining the crystallite rotation, or small angular range assumed by the octahedral slip plane after these various amounts of shear. The mechanism of recrystallization and the magnitude and effect of recovery on the recrystallization process was investigated.

Jan 1, 1940

By Alan Arias

On grinding in pure water, zirconium, tantalum, iron, and stainless-steel powders were extensively comminuted and simultaneously oxidized with hydrogen release, whereas nickel, copper, and silver powders did not react with water and their particle sizes increased. On grinding nickel, copper, and silver in water pressurized with oxygen, nickel and copper became extensively comminuted and were oxidized, whereas silver did not react with oxygen and its particle size increased. From these results and other considerations , it is hypothesized that for extensive comminution of ductile metals and alloys to occur on grinding they must react with the grinding media. UlTRAFINE metal and alloy powders are finding an ever-growing number of applications in metallurgy and in other fields.' Of particular interest are ultrafine metal and alloy powders suitable for dispersion strengthening.2'9 Various research programs on dispersion strengthening are being carried out and in some of these programs the ball-milling method is being used to produce dispersion-strengthened materials. This method usually involves the simultaneous grinding of metal or alloy and a dispersoid followed by consolidation of the resulting powder mixture. To obtain the ultrafine powders required for dispersion strengthening,' grinding is carried out in many liquids, including aqueous and nonaqueous media, with or without grinding aids.4'5 Nonaqueous liquids usually contain water as an impurity and some grinding aids may contain water of hydration.5 The water present may affect the grinding process. The writer has shown5 that. on ball milling chromium in water, the chromium is oxidized and hydrogen is released. It was surmised that the same reaction may occur on ball milling other metals and alloys in waterbearing liquids. Therefore, the investigation of ball milling in water was extended to metals and alloys other than chromium. In the course of the investigation, however, it became apparent that the data-to-gether with the results from a few additional experi-ments—could be used to postulate a comminution mechanism for ductile metals and alloys. A well-known comminution theory is that of smekal.7 According to this theory, comminution is possible because of the weakening effects of surface cracks and other imperfections in materials. This theory imposes a lower limit of about 1 µm for the ground particles. The beneficial effects of liquids and additives on the rate of grinding are well known.8 Mechanisms by which liquids and additives may aid in grinding were reviewed by Rose and Sullivan.' One aspect of these effects is based on Rehbinder's theory of crack propagation in materials under stress.9 According to Reh-binder's theory, liquids or additives may promote the spread of cracks in stressed materials by lowering the surface tension at the crack tip. Rose and Sullivan surmise that the same mechanism may be operative during grinding, thereby facilitating comminution of the particles. In addition, Rose and Sullivan reviewed how additives may act as dispersants as a result of their being adsorbed on the surface of the particles being ground. This concept has been suggested by Quatinetz, Schafer, and smea15 to explain from their experiments the major role of additives that enabled them to grind metal down to 0.1 µm. Discussions of other comminution theories and additional sources of material on the subject will be found in Ref. 10. None of these previous suggestions and theories, however, can account for all phenomena encountered during ball milling of metals to submicron size in this and in a previous investigation by the author.6 The objectives of this investigation were to determine the behavior of metal powders during ball milling either in pure water or in oxygenated water and to gain an insight into the grinding mechanism. Zirconium, tantalum, iron, nickel, copper, and silver powders were ball-milled in pure water. These metals were selected because their oxides cover a wide range of free energies of formation. For comparison purposes, an alloy-type 430 stainless steel-was also ball-milled in pure water. The pressure of the hydrogen released during ball milling was monitored in order to determine the oxygen that combined with the metal or alloy. In order to obtain more information on the nature of the grinding process, nickel, copper, and silver powders were also ball-milled in oxygenated water (water pressurized with oxygen). The oxygen that reacted with the powders was determined from the pressure decrease in the mills. The powders resulting from ball milling in pure water and in oxygenated water were subjected to surface area, optical microscopy, and X-ray diffraction analyses. With these data, the oxygen calculated to be combined with the metals during ball milling, and comparison of the free energies of formation of the oxides of the milled powders with that of water, a comminution mechanism was postulated. MATERIALS, EQUIPMENT, AND PROCEDURES The materials used in this investigation were powdered metals, deaerated distilled water, high-purity helium, and commercial grade (99.5 pct purity) oxygen. The powdered metals used were zirconium, tantalum, iron, nickel, copper, and silver. A 16 pct Cr, ferritic stainless steel, type 430, was also used. The purities (or nominal compositions) and the surface areas of these metals and the alloy are given in Table I.

Jan 1, 1970

By E. W. Dewing

The nature of solid solutions of sodium in non-paphitic carbon at temperatures near 1000°C has been investigated by an electrolytic technique. The activity coefficient is found to vary strongly with the heat-treatment temperature of the carbon, and an analysis of the energy terms involved suggests that this is due to variations in the Fermi level. The diffusion coefficient for sodium is in the range implying that the sodium atoms (or ions) are not bound to specific sites on the carbon, in agreement with lack of evidence for specific compounds in the activity -composition curves. In the light of These results phenomena occurring in aluminum reduction cell linings are dis-cussed. It is concluded that sodium migrates by diffusion through the carbon lallice and not the pores, and that A14C9 is formed within the lining hy The excess of NaF invariably found in used linings is formed by this reaction and by air oxidation: There has recently been much interest in the swelling of carbon which occurs when it is made cathodic in an aluminum electrolysis cell, and there is general agreement that the phenomenon is due to the penetration of sodium atoms, derived from the reaction on the carbon lattice. (NaF and AlF3 are constituents of the fused-salt electrolyte.) The low-temperature lamellar compounds of potassium with graphite are well-known, and one compound between sodium and graphite has been reported.4 There is, however, virtually no information on the basic chemistry of the interaction of sodium with nongraphitic carbon at high temperatures, although Dell3 has made some fundamental studies of rates of penetration. At the time the present work was carried out these were not available. Rapoport and samoilenkol had measured rates of physical expansion in a dilatometer, using the fractional increase in length of a carbon specimen after electrolysis in a cryolite bath for 2 hr as an index of susceptibility to cathodic swelling. Work here with a similar apparatus showed that expansion (of a 1.5-in.-diam cylindrical specimen) ceased in less than 20 hr, and that the final expansion was much more reproducible than the value at some intermediate time. This suggested that an equilibrium was being set up, and that a thermodynamic approach was required. The results obtained are not as accurate as had been hoped, but they are the only ones of their type available and have enabled useful conclusions to be drawn. The experimental work was divided into two parts: an investigation of the activity-concentration diagram for sodium in carbon, and a rough determination of the diffusion rate. For the former, most of the experiments were made with petroleum coke even though this is not a form of carbon used in cell linings. It has the advantages, however, that it is a homogeneous material, that it is low in ash, and that its structure is reasonably well understood. Anthracites and coal cokes gave results of the same type as obtained with petroleum coke, but the reprodu-cibility from specimen to specimen was extremely poor. EXPERIMENTAL 1) The Activity-Composition Diagram for Sodium in Carbon. The petroleum coke was ground, pressed at 40,000 psi into plates 19 by 9 by 2 mm without added binder, and heat-treated. The sodium activities were established by an electrolytic technique. The carbon was made anodic in a cryolite bath with an aluminum cathode, and a controlled potential, E, applied so that the sodium activity at the anode was given by ln Na = 1n asa - EF/RT [21 where as, is the sodium activity generated by Reaction [I]. The relative activity is sufficient for many purposes and is simply given by The value of Na not at present known, but when the thermodynamics of the Na-A1 system have been worked out it can be derived from the equilibrium

Jan 1, 1963

By W. B. Finkeldey, C. H. Mathewson, C. S. Trewin

This paper was prepared upon request as a contribution to a symposium covering the manufacture, properties, and uses of the important non-ferraus metals. In approaching a subject as broad as this, there is a natural desire to build up a comprehensive and finished production which shall constitute a dependable source of information on all questions properly belonging to this branch of metal technology. There are, however, a number of circumstances, apart from the mere routine of labor and thought involved, which operate rather effectively against the possibility of completing such .an ambitious program at the present time. First of all, as far as any public record of results is concerned, the commercial rolling, drawing, and forming of zinc with relation to changes of structure and properties—and this we consider to constitute the clement~ of metal technology—might as well be an unpractised art. We have never seen a published photomicrograph showing the structural characteristics of either hard or soft sheet or strip, although the structure of castings has been frequently described, and other coarse-grained structures resulting from hard-hammering and annealing have been reproduced. Thus, an author in this field must proceed to his task without much assistance from the literature, and the outcome can represent only a personal estimate of principles, facts, or findings, and not a summary or survey of progress in the entire field as determined by varied experience, practice, and settled opinion.

Jan 1, 1921

By Erwin L. Zodrow

A geological model of the modes of formation of magnetite and its distribution in the Smallwood iron-ore mine, Labrador, Newfoundland, is given, based on observation and geological mapping. This is called the conceptual model. If mathematical expressions plus probabilistic uncertainty are used to represent the conceptual model, then this is termed a mathematical model. The purpose of this paper is to test if there exists a correspondence between the conceptual model and two related mathematical models (called factor analysis). Details of the statistical technique are given. The results of factor analyses in relation to the magnetite formations in the Smallwood mine are discussed. Several practical mine applications are presented. The difficulty of maintaining quality control over ore mined from any deposit naturally depends on geological conditions; these are usually imperfectly known to concerned mining geologists. One geological condition that would greatly facilitate ore predictions is if a relationship between the observed ore particle distribution* and its mode of origin could be demonstrated. Such a casual interrelationship is normally sought through the application of well-defined geochemical principles of primary mineralization in given geological environments. However, the application of conventional tools of geological research, including geochemistry, to areas that have undergone repeated periods of geological deformation and metamorphism subsequent to primary mineralization becomes rather difficult. More important, the interpretation of such research results are nearly impossible on an objective basis. Mineral assemblages may have been reworked and changed due to tectonic influences to the extent that the present-day observable mineralogy and ore-particle distribution can effectively obscure the mode of origin of the ore. Quantitative measurements, based on petrological investigation of mineral assemblages, reflect the sum-total of all geological influences. Which of several influences had the most effect on existing ore particle distribution is difficult to assess, for these influences can neither be measured directly nor quantified by petro-logical logical or geochemical means. The present study is concerned with the magnetite distribution and its modes of origin within the Small- wood mine,' located in the southern extension of the Labrador geosyncline; see Fig. 1. This geosyncline is thought to have undergone at least two periods of geo-tonic tectonic deformation, separated in time, since the fer-rugenous rugenous sediments were deposited." Detailed geological observations and mappings (1 in. to 40 ft) have highlighted subtle, distinctive features of the magnetite distribution in the Smallwood mine: (1) The magnetite is generally concentrated in bands or layers within this ore body; these bands alternate with specularite-rich bands and quartz bands. The banded or layered nature is common in Precambrian iron-ore deposits, and this has been interpreted as a result of changes in depositional environments. (2) The grain size of the magnetite varies; near the contacts between the iron and quartz-carbonate formations, the magnetite occurs as well-crystallized octa-hedra. In areas of intense folding, magnetite is extremely fine grained and concentrated in bands and occurs in association with earthy manganese minerals. (3) Magnetite tends to be more highly concentrated near the geological contacts of the iron and quartz-carbonate formation in the northeast part of this mine, Figs. 2, 3, and 4. (4) Magnetite is also fine grained and tends to higher concentration near and parallel to fold axes; however, in this case, the ore is much softer than given in item 2. (5) Magnetite mineralization decreases along strike and away from the areas of intense folding, i.e., towards the approximate center of the mine, Fig. 3. How can these variations of magnetite be explained on a geological basis? We can postulate a conceptual model that the distribution of magnetite appears to be related to three basic geological influences: (1) geo-tectonics, i.e., concentrations of magnetite near geological contacts of the iron and quartz-carbonate formations, the fine-grained nature of magnetite and its higher concentrations near fold axes, and decrease of magnetite towards the approximate center of the mine; (2) secondary alterations, i.e., variation of grain size of magnetite near the iron and quartz-carbonate contacts, and in areas of intense folding where magnetite occurs together with earthy manganese minerals: (3) original

Jan 1, 1971

By J. J. Becker

Changes in magnetic properties with particle size are used to study the precipitation process in a Cu-Co alloy. In particular, the effect of a field during aging in producing anisotropy is shown to occur entirely during the growth of the particles, after precipitation is complete. HEAT-treatment in a magnetic field is done commercially to improve the magnetic properties of a number of materials. These can be divided into solid-solution alloys and precipitation alloys. The Permalloys are representative of the first type, and magnetic annealing greatly increases their maximum permeability. On the other hand, in precipitation alloys such Alnico 5 the important result is an increase in maximum energy product. The effect of the field in all cases is to bring about an additional magnetic anisotropy, uniaxial in nature, which makes the hysteresis loop more upright when measured in the direction in which the field was applied. The structural origin of the anisotropy brought about by magnetic annealing is not well understood. In the solid solution alloys, one possible explanation is based on ordering.' Another possibility is the orientation of like-atom pairs.' The precipitation systems known to respond to magnetic heat treatment are Alnico 2, in which the effect was first discovered," Alnico 5, cobalt ferrite (oxide),' and Cu-Co alloys.3 n these materials, the field affects the precipitation process itself in some way. Although there has been much work on Alnico 5. its nature is still incompletely understood. According to Geisler,' the precipitation reaction is of the

Jan 1, 1959

H. H. Bleakney (Dept. of Mines and Technical Surveys, Ottawa, Canada)— The work of Dr. Machlin and his colleagues at Columbia University is so scholarly that one hesitates to take issue with them. Nevertheless the writer feels compelled to enter a demurrer to the mechanism of intercrystalline cracking proposed in this paper. The principal obstacle to its acceptance is found in its preoccupation with purely mechanical influences and its disregard for the chemical effect of impurities. The writer believes that the destruction of metallic cohesion by concentration of impurities at the grain boundaries is a necessary and sufficient condition for the development of intercrystalline cracking; and he believes that discussion of the numerous mechanical explanations proposed should wait until some valid objection to the chemical hypothesis has been advanced. It is nearly twenty years since Gillett" drew attention to the possibility that the chemical influence of precipitation might be the cause of intercrystalline cracking. As early as 1935, Greenwood'" remarked that grain-boundary precipitation of impurities in lead appeared to promote intercrystalline cracking. Again in 1939, Scott commented as follows on a paper by Thielemann and Parker:'" "There are at least two familiar phenomena that can influence grain-boundary cohesion: 1) intergranular oxidation; and 2) grain boundary precipitation. An important consideration in this work, therefore, is to determine which, if either, of these factors is responsible for the low values of cohesive strength observed." In 1952. the writer presented evidence," some original and some abstracted, which indicated that in copper, silver, aluminum, lead and iron, intergranular cohesion was a function of the purity of the metal. In 1954 Glen, discussing a paper by Ridley and Tapsell14 indicated his belief in a precipitation mechanism for the intercrystalline embrit-tlement of molybdenum steel and suggested that with an absolutely pure metal it would be almost impossible to obtain an intercrystalline crack. This suggestion has

Jan 1, 1959