Search Documents

By B. Yarar, J. Kaoma

[Introduction The critical surface tension of wetting of hydrophobic materials has been investigated extensively by Zisman et al. (1973) and relates the spreading of a liquid on a solid to the surface tension of this liquid. Thus, the Zisman ap¬proach shows that a plot of Cos 0 versus ?LV where, 0 is the contact angle and ?LV is the surface tension of that liquid in contact with its own vapor at equilibrium, produces a straight line which can be extrapolated to Cos 0 = 1. The intercept corresponds to a given ?LV, termed the critical surface tension of wetting. In instances, however, Cos 0 - ?LV plots show deviations from linearity. Alternative approaches have also included the plotting of adhesion tension (YLV COs 0) versus ?LV that can be interpreted in terms of critical surface tension data (Lucassen-Reynders, 1963). It has, on the other hand, been customary to correlate contact angle (0) with flotation data, although it is recognized that surface inhomogeneities and related contact angle hysteresis limit the interpretations pertaining to solid surface structures purely based on contact angle measurements. It is nonetheless true that 0 = 0, when the liquid is water, corresponds to a hydrophilic solid. Determination of ?c by contact angle measurements in conformity with the Zisman approach can encounter experimental difficulties, especially when solids are in a powder form. Following the reasoning that 0 = 0 corresponds to the hydrophilic state of a solid, froth flotation experiments can be expected to produce critical surface tension of wetting values for powders. The technique that consists of plotting recovery (% R) versus YLV data and extrapolating the linear part of the curve to % R = 0, has been described elsewhere (Yarar and Kaoma, 1984). This paper describes some of the results obtained by the extrapolation technique mentioned above, using various sulfide minerals. Experimental Materials Molybdenite (MoS2), sphalerite (ZnS), chalcopyrite (CuFeS2), chalcocite (Cu2S), and galena (PbS) were handsorted from massive samples and ground by mortar and pestle, and the -147 Fan fraction used in experiments; sulfur (S) was a C.P. Fisher Scientific Co. product. Method One gram powder samples were conditioned for three minutes in methanol-water solutions of predetermined surface tension values and the percents recovered by flotation using a Partridge-Smith Cell (Partridge and Smith, 1972), were plotted against each ?LV value. Results and Discussion The percent recovery versus ?LV for two naturally hydrophobic solids, i.e., natural molybdenite, MoS2 and sulfur are given in Fig. 1 where it is seen that ?c for sulfur is obtained as 31.5 mNm-1 whereas for MoS2, it is 26 mNm-1. Figure 1 also shows that the new flotation technique described, for estimating ?c is in good agreement with the Zisman method. Curves obtained by the same method for the minerals Cu2S, PbS, and ZnS are given in Fig. 2, where it is seen that for Cu2S, ZnS, and PbS, the extrapolation to % R = 0 produces ?c values of 36, 39, and 49 mNm-1, respectively. CuFeS2, on the other hand, gives a curve that does not permit such an extrapolation to obtain a ?c value with certainty. Nonetheless, treatment of the powder with 8.95 X 10-5 molar Na2S solution followed by washing with distilled water prior to flotation effects the curves as shown in the insert of Fig. 2. The type of curves given in Fig. 1 appear to be typical of hydrophobic solids as can also be observed in Fig. 3. The composition of solid and minute quantities of inclusions seem to play an important role as regards the surface properties of solids as reflected by the slope of the linear part of the % R - ?LV plot and thus the value of ?c obtained by this technique. For example, MoS2 of three different stoichiometric compositions produced the data given below. [MoS2MoS2.14Mo1.002S2 ?c mNm-126.029.031.0 dR/d?8.95.23.0]]

Jan 1, 1985

Apart from the general cooperation received in many quarters, the Unitization Committee desires to make specific acknowledgment to the following individuals for assistance rendered in the study to this time. California.—Committee members: Joseph Jensen, chairman, L. L. Brundred, E. M. Butterworth, H. Norton Johnson, D. B. Myers, W. R. Wardner; others who contributed: C. R. McCollom, F. C. Merritt, E. B. Noble, Ralph Arnold, J. R. Pemberton, Roy R. Morse, T. F. Stipp, John R. Roberts, R. D. Bush, Alexander Anderson, J. A. Taff, F. 0. Martin, J. E. Van Gundy, E. K. Parks, A. C. Rubel, Lew Suverkrop, W. L. McLaine, Gerard Henny, Walter Stalder, Lester C. Uren, Hoyt S. Gale, W. L. Walker. Rocky Mountain.—Fred E. Wood, chairman, J. G. Bartram, C. E. Dobbin, Wilson B. Emery, Charles E. Erdman, R. D. Hawley, E. W. Krampert, Foster Morrell, W. T. Nightingale, K. B. Nowels, C. M. Rath, Earl Shoenfelt, J. W. Steele, E. T. Wilson, J. J. Zorichak. Kansas-Oklahoma.—Committee members: C. E. Beecher, chairman, A. W. Ambrose, R. C. Hauber, Clyde Alexander, R. F. MacArthur, C. R. Swarts, M. M. Valerius, E. H. Griswold, G. 6. Rollin, L. Murray Newman, David L. Trax, Richard K. Huey, Marvin Lee, Harry Johnson; others who contributed: E. A. Carr, Paul S. Ache, K. C. Slater, R. S. McFarland, J. R. McWilliams, Joseph Chalmers, Henry A. Ley, Dorsey IIager, H. C. George, W. K. Whiteford, L. G. E. Bignell, L. E. Smith, George E. Burton. Texas, Louisiana, Arkansas, New Mexico.—Frederic H. Lahee, chairman, Donald C. Barton, C:. E. Beecher, Olin G. Bell, G. E. Campbell, Paul Wagner, John West, Robin Willis, J. M. Forgotson, E. J. Gorman, P. S. Haury, Marvin Lee, C. F. Lytle, L. H. McBee, T. F. Petty, C. C. Pope, F. S. Prout, J. C. Stewart, J. R. Suman, L. P. Teas, W. C. Thompson, A. F. Truex, R. B. Campbell, M. G. Cheney, P. C. Dean, F. W. DeWolf, Dugald Gordon, B. A. Hardey, F. E. Heath, J. F. Lucey, George C. Matson, W. H. Perot, T. W. Pew, W. A. Price, W. A. -Reiter, R. C. Stewart. Eastern United States and Foreign Fields.—H. H. Hill and E. L. Estabrook, chairmen; Dr. Richard Ambronn, Gottingen, Germany; Arthur R. Andrew,

Jan 1, 1930

By D. Y. Geng, Syd S. Peng

This paper analyzes the effects of geology and mining methods on surface subsidence factor, angle of draw and angle of critical deformation based on the results of 40 longwall subsidence profiles in the Northern Appalachian coalfield. Several equations were derived to show the relationships between those parameters. Furthermore, the equations were transferred and plotted in the form of several monographs for convenience of applications.

Jan 1, 1982

By A. H. Daane, B. J. Beaudry

The Sc-Y and Sc-Zr systems were studied by thermal and X-ray methods. Both systems are characterized by complete solid solubility in the low temperature hexagonal form and in the high temperature bcc form. In the Sc-Y system, there is a minimum in the solidus at 50 at. pct and 1365°C, while the solidus in the Sc-Zr system follows a nearly straight line relationship between the melting point of scandium and zirconium. There is a minimum in the temperature of transition from hexagonal to bcc in the Sc-Y system at 43 at. pct Y and 1175°C; while the temperature of transition is raised in the Sc-Zr system to a maximum of 1415 °C at 30 at. pct Zr. INTEREST in the metals of the first transition series has usually stemmed from their useful properties; however, there is now a great deal of interest in determining the fundamental nature of these metals. Since scandium is the first of these transition metals, a study of the preparation and Properties1 and the alloying behavior of scandium2 was initiated. In a continuing study of the alloying behavior of scandium, the systems of scandium with zirconium and yttrium have been established. Extensive solid solubility in both the Sc-Zr and Sc-Y systems was expected from application of the classical rules of Hume-Rothery. Also, the modified Darken and Gurry plot as suggested by Gschneid-ner3 showed ideal conditions for solubility in the Sc-Zr system with less favorable conditions in the Sc-Y system. The effect of scandium on the transformation temperature of zirconium and yttrium was of interest, since a recent empirical observation by Uly and Burr4 predicted that the solute scandium would raise the transformation temperature of zirconium and lower the yttrium transformation. In addition to noting the validity of the above predictions, the SC-Y and Sc-Zr systems were established. EXPERIMENTAL METHODS Materials. The metals employed in this investigation were crystal bar zirconium, distilled scandium prepared by the method described by Spedding, et al.1 and yttrium prepared by the method described by Carlson, et a1.5 The major impurities present in these metals are listed in Table I in ppm. Alloy Preparation. All the alloys examined were initially formed by comelting the two metals in a nonconsumable electrode arc-melting furnace under an atmosphere of purified helium or argon. The buttons were inverted at least five times and re-melted each time to ensure homogeneity. During preparation of Sc-Zr alloys, approximately 1 wt pct was lost which was attributed entirely to the loss of scandium by distillation. When preparing Sc-Y alloys, approximately 1.5 wt pct was lost, but it was assumed that the intended composition was maintained, since the relative weight lost when arc melting the component metals was nearly the same. Samples weighing 15 to 20 g were prepared for time-temperature thermal analysis, while only 1- to 2-g samples were prepared for the optical pyrometer and X-ray diffraction studies. Thermal Methods. The solidus and the melting points of the metals were determined by an optical pyrometer method described previously.2 The temperatures at which the transformation from hexagonal to bcc occurs were determined by differential thermal analysis. Several points on the solidus and liquidus in the Sc-Y system were also determined by this method and are in good agreement with those obtained by the optical pyrometer method. The procedure followed in the preparation of samples for thermal analysis and the furnace used have been described elsewhere.2'6 Since a limited quantity of scandium was available, most of the alloys were not melted during thermal analysis, thus avoiding contamination by the crucible. The alloy could then be reused and the composition changed by adding the desired quantity of solute to obtain the next alloy. Heat Treatment and X-Ray Methods. In order to ensure homogeneity, the "as arc-melted" alloys Were wrapped in tantalum foil, sealed in quartz capsules and heated at 1100°C for 15 hr and then cooled at a rate of 8 deg per min. Samples for X-ray diffraction were filed from these heat-treated alloys, sealed in 1/8 in. by 1/2 in. tantalum capsules under

Jan 1, 1963

By D. C. DERINGER

METALLURGISTS and mill operators appreciate, in a general way, .the economic or commercial relationship between recovery and grade of product but few have correlated in detail fluctuating metal prices with the metallurgy. They know that many factors such as metal price, dedusiions for returning charge, transportation, percentage of metal in head ore, etc.; all affect the commercial relationship between recovery and grade of product. In practically every mill some one at some ' time has calculated the amount of recovery that can be sacrificed for each percentage increase in grade of concentrate and from this calculated ratio the commercial or ., economic tail has been established. Such a ratio finally becomes a well-entrenched rule by which the progress of the metallurgy is judged.. When once established, these-, ratios are but seldom corrected to changes of metal prices for each possible grade of concentrate that may be produced. The calculation is tedious when often repeated. Other methods have been suggested and used to correlate the commercial with the metallurgical phase. A factor .derived ,by multiplying the grade of concentrate by recovery is often used, but is of little importance because it does not possess a single commercial quantity. The percentage monetary recovery calculated by dividing the gross value of the ore into the net smelter return gives a good economic index and, is to be commended, but it is difficult to correlate exactly and quickly the work of each day on a commercial basis.

Jan 1, 1931

By Earl E. Hunner

At the end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping southwest, or exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a north-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly. Problems and Plans In order to understand what follows, the general layout and equipment of the mine as it was at this time must be briefly described. Fig. 6 indicates the relative positions of the shafts. The North Star (incline) shaft extends from the surface to the 6300-ft. level following the vein, with an average pitch of 26", between limits of 11" to 38. There is at present no hoisting equipment in this shaft between the 2700 and 4000-ft. levels. The Central (vertical) shaft connects with the North Star shaft at the 4000-ft. level, at a vertical depth of 1600 ft. In two compartments of this shaft 4-ton skips made a vertical turn of 15 ft. radius at the 4000-ft. level and ran down the incline to the 6300-ft. level. A cage operated in the third compartment to the 4000-ft. level. Men and supplies were transferred to a truck running on a third track down the incline shaft to the 6300, operated by an electric hoist on the 4000-ft. station. When the shifts changed double-deck cages were substituted for the skips in the vertical shaft, but they stopped at the 4000-ft. station. The truck to 6300 carried 22 men, and it required 8 min. to make a trip down and back. This arrangement was satisfactory as long as a fairly large proportion of the work was

Jan 1, 1930

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949

By Arthur F. Taggart

TO all Mineral Dressers, but particularly to those in the Coal and Industrial Minerals Divisions: Ted Counselman, retiring after two years at the helm of the Milling Committee, pointed with pride to the continued growth of that committee, and sang the swan song "Why ain't we a Division of Mineral Dressing?" Our genial Secretary pointed out, handily, that, you see, the way the Institute is divided there are several blocks running across this way here, and one running all the way down here, and another running part way down here, and they all cut across each other like this, and anyway the miners want to be a Division now, so why not you Mineral Dressers be good and not upset the big Institute organizational chart? And anyway again, Divisions have vested interests, and a Division of Mineral Dressing would take something away from Coal and something from Industrial Minerals, and any good institutional man can see that a Division would never give anything up. It was all quite confusing, and apparently not too convincing, because then the Milling Committee went ahead and voted unanimously it is a good idea, let's see what the other fellows think about it as well.

Jan 1, 1944

By M. E. Hassan, J. C. Calhoun, R. F. Nielson

An apparatus was constructed for the measurement of inter-facial tensions over a range of temperatures and pressures. This apparatus utilized the pendent drop method, and resembles in construction similar apparatus recently described in the literature and in use in some petroleum research laboratories. The interfacial tensions of benzene, propane, n-pentane, n-hexane. n-octane. and iso-octane against water were measured at temperatures ranging from 26" to 82" C and at pressures ranging from 1 to 204 atm. Values of interfacial tensions for the henzene-water system and their variations with temperature and pressure are generally in good agreement with value? of previous investigations. The data in all cases showed a slight decrease of interfacial tension with pressure at constant temperature in the range studied. The effect of pressure became less as the pressure was increased, with an indication of a reversal of the effect at higher pressures. There was a decrease of interfacial tension with temperature at constant pressure in all cases, as would normally be expected. This rate of decrease became greater the higher the temperature. A general equation is presented for the interfacial tensions as a function of presPurp and temperature over the range studied, and the constants calculated for each system. A definite trend was found in the effect of molecular weight on the interfacial tension at a given temperature and pressure, for the homologous series from propane to n-octane. Data for n-decane from the literature fitted well into this trend. INTRODUCTION It has been recognized for many years that surface forces play an active part in the production history of an oil reservoir as well as in determining the amount of unrecoverable oil. The magnitudes of these forces are governed by the values of the interfacial tensions. These vary greatly with composition, pressure, and temperature. The effect of composition is greater than that of pressure and temperature over the ranges normally encountered. In fact, because of the variety of compounds present in a crude, no attempt has yet been made to correlate crude composition with its surface tension or with its interfacial tension against water. The amount of dissolved methane greatly affects the surface properties of an oil, and there are "surface-active" compounds in crudes which have a much greater effect on boundary tensions than do equal amounts of hydrocarbons. The purpose of the present work was partly to contribute data that would eventually be used in correlations applicable

Jan 1, 1953

Granduc lies near the Alaskan border in British Columbia, about 600 miles (960 km) north of Vancouver. Prospecting in the area must take place in the short summer months of fog and rain because the winter is bitter cold, with snowfall up to 960 inches (24.4 m) accompanied by avalanches. Despite these difficulties, the mineral ized area was discovered in the 1920's. By 1956, Newmont Mining Corporation had developed mineable ore reserves estimated at 32,500,000 tons of 1.93% copper. Newmont and ASARCO, in a joint venture, then began development of the ore body, which was partially covered by glaciers. It was apparent a concentrator could not be built at the mine site where overland access was impossible due to the weather conditions and the terrain. Years of engineering studies of all possible access routes finally dictated the driving of an 11 mi long (17.6 km) tunnel passing under three glaciers and three mountain ranges to the nearest feasible concentrator site at Tide Lake. Even then, a mountain road subject to an average snowfall of 800 in. (20. 3 m) had to be built 32 mi (51 krn) from the concentrator through Alaska to Stewart, British Columbia, the nearest port. At Stewart, which is located at the head of a fjord 120 mi (192 krn) from the Pacific Odean, a fully equipped marine terminal was built. The tunnel, the lifeline between mine and mill, was to be driven from both ends; however, in 1965, an avalanche occurred at the Leduc portal, killing 26 crew members and wrecking much of the camp. The tunnel was then driven from one heading adjacent to the concentrator site at Tide Lake, a distance of 53,744 ft (16,381 m) to a point under the ore body. The remote location, type of terrain, and bad weather made supply of crews, equipment, and construction materials difficult; but in spite of these extremely adverse conditions, the tunnel crews set many world records. Mineralization throughout the ore zone is generally uniform in grade and composition and is primarily chalcopyrite and pyrrhotite associated with pyrite. Mining is mainly by sublevel caving. After blasting, rubber-tired load-and-haul equipment moves from level to level by means of an internal connecting ramp system on a 15% slope. At the gathering haulage level, 15-ton bottom-dump cars deliver the ore to a 600-ton pocket equipped with a Hudson "Rock-Flo" dump. The bottom of the ore pocket forms the feed chute to the primary

Jan 1, 1978

By Fred R. Harris

INTRODUCTION MacMillan Tungsten is located in northwestern Canada on the border of Yukon and Northwest Territories at a latitude of 63º17' and altitude of 1800 m above sea level. The deposit lies within the Selwyn Mountains 10 km from the Canol Road. It is 660 km by road from Whitehorse, Yukon, and 1325 km by air from Vancouver, British Columbia. MacMil lan Tungsten is a contact metasomatic deposit in gently dipping Lower Paleozoic limestone and limestone breccia adjacent to a Cretaceous quartz monzonite stock. Four tabular tungsten skarn horizons contain total geological reserves of 30 million tons grading 0.9% WO3. DISCOVERY AND HISTORY J.F. Allan, a former AMAX geologist, located mineral claims in September, 1962, to cover the source of scheelite-bearing skarn float found in the headwaters of Cirque Lake Valley. Exploration work on the property conducted mainly between 1968 and 1973, includes geological mapping, 10,500 m of diamond drilling in 73 holes, and 735 m of underground exploration. Mil 1 tests were carried out on a 300 ton bulk sample obtained underground. Preliminary feasibility studies, collection of weather data and a variety of environment studies have been carried out since 1973. Although no production date has been set MacMillan Tungsten will undoubtedly be a major tungsten producer.

Jan 1, 1976

By John R. Anderson, Michael B. Bever

CARBON may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,1 the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. EARLIER DATA The solubility of carbon in molten pure copper is about 0.0001 pct at 1100 °C and 0.0004 pct at 1475°C.1 Various authors2-6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range 1217° to 1245°C. This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By Michael B. Bever, John R. Anderson

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By A. T. Aldred

HIS note reports the existence of several new scandium intermetallic compounds of the A2B and AB stoichiometries where the A element is scandium and the B element is from group VIII or IB of the periodic table. Alloys were arc melted from high-purity materials using 2-g charges. Typical lot analyses for the materials used are given in Table I. Chemical analyses were not made on the alloys as there was little or no weight loss on melting. After annealing the specimens for 14 days at 600°C and water quenching, metallographic and X-ray techniques were used to determine the occurrence of the various phases. Table II lists the relevant data for the A2B phases. The Ti2Ni structure,2 has ninety-six atoms in a face-centered cubic cell, whilst the Al2Cu structure is body-centered tetragonal.3 The occurrence and stability of the various A2B type phases in transition metal alloy systems has recently been considered by Nevitt.4 The Ti2 Ni-type phases occur over a relatively narrow range of radius ratios from 1.14-1.26 with A partners mainly from the titanium group and B partners predominantly from the cobalt group. This suggests that both a favorable relative size of the atoms and a favorable electron concentration are necessary conditions for the existence of this structure type. A12Cu-type phases involving Ti group elements as A partners are formed with B partners from the cobalt and nickel groups, predominantly the latter, and have a higher radius ratio (1.27-1.29) than the Ti2Ni-type phases. The occurrence of both Sc2Pd and Sc2Co can be rationalized in terms of these considerations but SczNi is anomalous because of its high radius ratio. The radius ratios are calculated from the Goldschmidt CN12 radii and it might be postulated that the scandium atom is reduced in size in the compound. Unfortunately the apparent atomic size of scandium in the compound cannot be calculated from a knowledge of the structure and lattice dimensions. The crystal structure of the Sc2Au compound could not be identified from the powder diffraction pattern, but it is interesting to note that it is isostructural with a series of A2Au phases where A is a rare earth element.5 Pertinent information concerning the AB phases found in this investigation is given in Table 111. All the phases have the ordered bcc CsCl structure. The occurrence and stability of CsC1-type phases have recently been discussed by Dwight,7 who concludes that the relative sizes of the atoms do not appear to be a controlling factor (the radius ratios of all the known phases vary between 0.985 and 1.439) but that the occurrence of the phase is predominantly dependent on the relative positions of the A and B partners in the periodic table. As a measure of the stability of a given CsCl phase it has been customary to define a lattice contraction on alloying, DAB — dAB, where DAB is the AB interatomic spacing as calculated from the Goldschmidt CN8 radii and dAB is the AB interatomic distance in the compound (= v3/2 ao). Values of the parameter DscB -dScB for the compounds found in this investigation are given in column 5 of Table III and are plotted in Fig. 1. If the lattice contraction does in fact reflect the stability of a phase then Fig. 1 shows two very interesting trends when the position of the B partner in the periodic table is considered. Firstly, within any given group the stability increases in order on going from the first to third long period. Secondly, within any given period the stability increases in order as the B partner is taken from the copper, nickel, and cobalt groups. In the case of the second long period, the lattice contraction reaches a maximum at ScRh and then decreases to ScRu. The same trend could

Jan 1, 1962

By Howard N. Eavenson

TWO months ago, just after the coal code hearing in Washington, one of our leading liberal weeklies printed a study of the coal industry made by an economist in the Administration, and on the outside cover bad it featured as "Coal-A Dying Industry." There are, of course, different opinions as to the accuracy of this characterization and I want to present some of the facts about the outlook for the bituminous industry for a short time ahead. In view of what has happened in the industry within the recent past it would be futile to attempt to make any prophecy about what is likely to occur in the future. We all know that a prophet is not without honor save in his own country, but it is likely that anyone undertaking this role about this industry would soon find himself in no man's land. One can, with some slight degree of safety perhaps, outline present conditions and tendencies and draw some inferences as to what the future may hold.

Jan 1, 1933

By J. S. Kirkaldy, R. J. Brigham

AS part of a program to investigate the diffusive properties of dilute ternary austenites we have made a determination of the effect of chromium on the activity of carbon in ? iron. Samples of pure iron and Fe-Cr alloys were simultaneously equilibrated at 1000°C with atmospheres of controlled CO/CO2 ratio following the procedures of Darken and Gurry 1 and smith.' The 0.020 in. thick samples were analysed for carbon by microcombustion analyses3 to yield a set of isoacti-vity curves. The latter were converted to activity coefficient (standard state at infinite dilution) plots by combination with Smith's data2 for the activity of carbon in pure iron. Table I shows the compositions of the base alloys used while Fig. 1 shows the experimental results superimposed on a set of curves generated by the relation In?C=6.9NC- 10.7 Ne In the notation of wagner4 the interaction parameter is the second coefficient on the right, Sgr = - 10.7 This can be compared with a rather inaccurate value deduced from the transient equilibrium diffusion data of Kirkaldy et al.' as The authors are indebted to the American Iron and Steel Institute for financial support. This material is condensed from a B.Sc. Thesis submitted to Mc-Master University by R.J.B.

Jan 1, 1963

INTRODUCTION TO PROBABILITY THEORY The mathematical theory of probability provides the foundation for the interpretations and inferences that can be made from statistical techniques. Probability theory is a broad field of study in itself, and can only be touched on here in order to provide the necessary back- ground for a more complete understanding of statistical analysis. Probability is concerned with the outcome of random events. It had its beginnings in the theory of games of chance which were of great interest to European mathematicians during the last half of the 17th century. The outcome of a random process or experiment is defined as an event. The collection of all mathematical points associated with each event is called the sample space for an experiment. Consider a random experiment having a finite number, n, of possible outcomes, some of which have a characteristic A. What is the probability that A will result from a single

Jan 1, 1980

By L. B. Herring, Harold Decker

The South Texas area, discussed herein, represents districts 2 and 4 of the Texas Railroad Cominission and extends from Jackson, Lavaca, and Gonzales Counties on the northeast to the Rio Grande River, comprising a total of 26 counties.$ The present boundaries of this district do not coincide with those of earlier reports published in the annual volumes of Petroleum Development and Technology. The war, in its various ramifications, determined and controlled all the phases of the oil and gas industry. Priorities for material and governmental subsidies determined all new operations. New Pools In our opinion, the combine' quantity of crude and distillate reserves added in '943 approached Or possibly exceeded the amount produced. Thirty-five new pools were added to the area' Of these, five have significant reserves and ten offer possibilities of containing consequential reserves. The largest proven reserve discovered during the year was the Slick pool, on the DeWitt-Goliad County line. This is also the most important Wilcox discovery to date in the area. The most significant extension was at Willimar, Willacy County. Other important extensions were developed at Agua Dulce, Seeligson, and Odem. Except for the Porter field, in Karnes County, the Laredo trend, which produces lrom the Jackson and Yegua, proved very disappointing, and this pool is o:C secondary importance. The Scott and Hopper pool, Brooks County, has only orie well, but offers excellent possibilities of becoming an important discovery. It represents at this time the major Frio discovery of the year. The Hobson pool, Karnes County, is not a major reserve, but can be classed as important in that it produces at a shallow depth from the Wilcox. This proves that the potential area of production for this zone occupies a broad trend. Gas and Condensate During the year construction was begun on only one recycling plant, this being in the Sejita field, Duval County. Several others were colltemplated, but no actual operations were begun. The most important development in recycling was the rebuilding of old plants to allow for the fractiona-tion of isopentane, n-butane, isobutane, and propane. Heretofore all pentanes plus have been marketed as cLdistillate,n only a minor portion of the butanes being isolated and sold for fuel purposes. All these new the except propane, are considered vital to the war effort and propane is being marketed as fuel gas. In other instances propane is being isolated and then pumped back into the gas reservoirs for storage. It is anticipated that the demands for this product will increase in the future. Drilling in the Wilcox trend during the year showed the existence of valuable gas

Jan 1, 1944