Search Documents

By Bruno Nordberg

THE high cost of coal in Butte and the development of large amounts of cheap electric power from the Missouri river caused the Anaconda Copper Mining Co. in 1908 to make an investigation as to the possibility of adapting this cheap electric power for the operation of their many large hoisting plants. At this time electric power had already been adopted for practically all other power purposes around the mines, such as pumping, compressing air, etc. The map (Fig. 1) shows the location of the mines of the Butte mining district. These mines are located within a circle of approximately a 1-mile

Jan 9, 1913

By John H. Bassarear, A. A. Dor

INTRODUCTION Primary grinding mills as defined in this paper, are autogenous or semi-autogenous rotating, tumbling mills having a coarse feed with a top size usually varying from 150 to 300 mm (6 to 12 inches). Most frequently, the feed to these mills is the product of primary crushing plants but in some cases run of mine ore is used as feed such as at Benguet, McDermitt, L-Bar Sohio, Bear Creek and others. The size of the largest lumps in the mill feed is principally determined by limits set by the mill feed trunnion diameter and by the type and size of conveying equipment used for handling and of bins and stockpiles used for storage. The use of primary mills in mineral processing plants has expanded very significantly in the last twenty years, and they have been successfully applied to the treatment of a wide variety of ores in both wet and dry grinding applications. In the present state of technological development for primary grinding mills, there is a wide choice of acceptable options with respect to type and size, grinding flowsheet and grinding media. The choice of the optimum combination which would result in the most satisfactory condition of operation, from the standpoint of both metallurgical results and costs, depends on the nature of the ore, the required characteristics of the grinding products and on various geographic and economic circumstances. The effects of such factors and considerations on the choice and sizing of primary grinding mills and flowsheets are reviewed and discussed in the following pages. PRIMARY MILLS SELECTION Inherent Characteristics of Primary Grinding Primary grinding is complex because it involves several comminution mechanisms which occur simultaneously and to some degree interfere with one another. These mechanisms of impact, attrition and abrasion have been described earlier. The relative importance of these three main grinding actions and their mutual balance resulting in a continuous uniform operation of the mill depend to a very large extent on the nature of the ore and its physical properties. Homogenous, single mineral ores will behave quite differently from heterogenous ores consisting of different minerals bound together along defined

Jan 1, 1982

By D. B. Hobbs, L. W. Kempf, R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13 per cent. of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 25S, Special 17S and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings. REVIEW OF LITERATURE The literature on the heat treatment of aluminum-silicon alloys is not very extensive. The following review gives the principal references of which the authors are aware, in which appreciable information may be found.

Jan 1, 1928

By Bailey, Lewis Newton

Bailey, Lewis Newton, Master Engineer, Senior Oracle, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia, at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Ballamy, John H., Capt., 103d Engineers, killed in action near Fismes, Aug. 9, 1918. Burt, Andrew, died in active service, 1916. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on October 7, 1915. Dougall, Ralph, 4th University Co., Princess Patricia Regiment, killed in action early in the war. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M. killed in action on October 12, 1917. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service, Jan. 1,, 1918. Hall, William T., Capt., Royal Flying Corps, killed in action, May 19, 1917.

Jan 11, 1918

By Gordon H. Geiger, J. Bruce Wagner

Electrical conductavity and therrnoelectvic nzeasuretnents on synthetic hematite slabs with 0.01 to 0.90 at. pet Ti and with 0.30 at. pet Ca were made. Additions of titanium and of calcium both increased the electronic conductivity with titanium yielding greater n-type behavior and calciurn p-type behavior. Reduction studies of hematite to magnetite in CO-CO2 atmospheres between 600° and 900°C initially exhibited linear kinetics. These linear rates were increased by additions of titanium and decreased by calcium. IN recent years many studies have been reported in the literature on the kinetics of the reduction of hematite and magnetite to iron. In addition, Hansen and Josephl and Schenck and Schultz2 have reported studies on the reduction of hematite to magnetite, the first step in total reduction to iron. In order to evaluate the results of the studies of over-all reduction in terms of the actual mechanism of the reaction and to define further the important factors in the rate- controlling mechanism of the magnetic roasting reaction, the following experiments were undertaken. Specimens of undoped hematite and hematite containing titanium or calcium in solution as doping agents were reduced to magnetite in CO-CO2 mixtures. In addition, electrical-conductivity measurements were correlated with the reduction kinetics using concepts of defect solid-state chemistry. EXPERIMENTAL Fisher certified Fe2O3 powder was used to make specimens for both the electrical and kinetic studies (see Table I for analysis). Doping with titanium and calcium was accomplished by adding TiO2 and CaO powders to the Fe2O3 powder. The powders were mixed in a Waring blender for minimum times of 1/2 hr. Satisfactory blending was achieved based on comparison of analyses of individual specimens af- ter reduction. The specimens were formed in a steel die using opposed punches with a rectangular opening 10.0 by 40.0 mm. The Fe2O3-TiO, platelets were pressed cold at 16,000 psi. They were sintered for approximately 16 hr at 1075°C in air, in accordance with information in the literature3, 4 on the time and temperature needed to obtain solution of the titanium in the hematite. The Fe2O3-CaO mixtures were first cold-pressed at 20,000 psi and sintered for 3 hr at 1225°C to insure solution of CaO. This material was then ground to -325 mesh in a 6-in. ball mill and the resulting powder was used to make platelets in the same manner as above. The sintered platelets were usually between 1/16 and 1/8 in. thick. They were ground on a carborundum wheel and polished on 2/0 paper. Typical dimensions of the kinetic-study specimens were 1.6 by 0.8 by 0.05 cm, and a typical weight was 0.3 g. Conductivity and thermoelectric specimens were approximately the same size, but were subjected to further sintering in order to ensure maximum densification. Finally, all specimens were measured to the nearest 0.0005 in. and weighed on a Mettler H-15 balance to the nearest 0.0001 g and the density calculated. The average density of the specimens used for the reduction studies was 4.87 g per cc, or 7.1 pet total porosity. The standard deviation ranged from 0.14 to 0.063 g per cc within a composition group. In the present study, the apparent surface area as measured with a micrometer was taken as the true surface area. The chemical analyses for calcium and for titanium within a group showed maximum variations of 50.04 pet from the average values used in Figs. 9 and 11. In order to suspend the specimen from the balance for the kinetic studies, a hole, 0.03 in. in

Jan 1, 1965

By T. L. Joseph

The extent to which hot metal from the blast furnace affects open-hearth practice and the quality of steel produced has been discussed widely. Open-hearth operators have attributed difficulties experienced in making satisfactory steel to characteristics of the pig iron not disclosed by ordinary analysis. The commonest criticism of the iron has been that it is "physically cold" or "dirty." Often when the blast furnaces are working irregularly the quality of the iron is questioned. A cold hearth, slipping and hanging, the use in the past of unsintered flue dust, and the use of ores difficult to smelt have been associated with the production of iron of poor quality. The difficulty of the situation is that we have no proven yardstick for quality aside from ordinary analysis. Uniformity in analysis is recognized as being important, but the difficulty of changing the open-hearth practice when the iron analysis varies widely may not always be fully appreciated. Although the problem of correlating the characteristics of steel with those of pig iron is admittedly obscure, the effort of producers of quality steel to investigate all factors that may have a bearing on the final product is justified. This report contains data on the oxides in several hundred casts of basic iron produced in a furnace during the course of normal operation on Lake ores. Incidental to the study of the oxides in the iron, it was desirable to follow closely the temperature of the iron. The effect of temperature of the iron upon the silicon and sulphur present is discussed. A general relation between the basicity of the slag and the sulphur in the metal was developed. The amount and composition of oxides in the hot metal and in the steel bath during various intervals between melt-down and tap are discussed. Heats of rimmed steel, killed steel, and semikilled steel were investigated. The hot metal on individual heats was either all taken from a mixer or consisted partly of direct metal and partly of metal from the mixer. Samples of the iron for oxide determinations were

Jan 1, 1937

By Thomas T. Read

Jan 1, 1913

By AIME AIME

THE Tuesday afternoon session", H. A. Bedworth chairman and T. S. Fuller, vice-chairman, was opened with D. J. McAdam, Jr.'s paper entitled "The Influence of Cyclic Stress on Corrosion." This paper dealt with the influence of cyclic stress on corrosion of alloy steels, corrosion-resisting steels, monel metal and aluminum alloys. The paper was discussed by T. S. Fuller, who pointed out that steels under stress corroded more than unstressed steels when subjected to steam.

Jan 1, 1930

By William F. Boericke

KIRKLAND LAKE and Porcupine in 1931 accounted for more than $41,625,000 of Ontario's total gold production of $43,117,688. For the first time, the younger camp surpassed the older in gold output, producing $21,734,000 against $19,891,000 for Porcupine. Present output of both camps is increasing, and should pass the record figures of 1931 before the year is out. In May of this year, Porcupine mines milled 285,759 tons, with a bullion value of $1,810,009; the corresponding figures for Kirkland mines are 149,188 tons and $2,104,757. A much higher average value per ton for Kirkland ore, $14.10 against $6.33 average for Porcupine accounts for the difference. The two fields are about 100 miles apart by rail, and there are important differences in the character of the ores, which accounts largely for the difference in milling costs and in final tailing values, despite excellent metallurgical work in both the fields.

Jan 1, 1932

By Peter N. Calder, G. H. Blackwell

The development of an open pit slope monitoring system, from equipment selection and justification to complete computer data storage and analysts, Is described. Methods of overcoming the Limitations of the electronic transit/distance measuring device and survey system selected are discussed. Results of the monitoring program showed that blasting was a major cause of Instability, and, after much experimentation, suitable blast patterns for mine production and pit wall integrity were designed. The experiences gained with double benching 'and wall cleanup procedures are discussed . The monitoring program also indicated that water was a contributor to instability, and methods of dealing with water In a rock with a low storage coefficient and transmissibility are described. Because of the danger of falling rock, photogrammetric methods are used for joint mapping and analysis, this work being contracted out. Joint strengths are measured on-site using a portable shear tester. Finally, a discussion of a complex failure is given.

Jan 1, 1983

By D. J. McAdam

As shown in three recent papers by the author, in two papers by McAdam and Mebs, and in a paper by McAdam, Mebs, and Geil," the technical cohesive strength of a metal, in any particular state as regards mechanical treatment and heat-treatment, cannot be represented by a single stress value, but must be represented by a diagram with the principal stressest as coordinates. Each point on the boundary of such a diagram represents a technical cohesion limit. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing fracture under a specific stress combination. Moreover, neither the yield strength1 nor the ultimate strength can be represented completely by a single stress value, but must be represented by a diagram with the principal stresses as coordinates. All combinations of the principal stresses may be classified in three groups as illustrated by Fig. I. Fig. Ia shows three typical stress combinations with no two principal stresses equal. The magnitude of each principal stress is indicated qualitatively by the length of the arrow. Arrows pointing away from the cube indicate tensile stresses; arrows pointing toward the cube indicate compressive stresses. Typical stress combinations with two principal stresses equal are illustrated in Figs. rb and Ic. Such stress combinations would be produced by subjecting a cylinder to combinations of uniform axial and radial stresses. The uniform radial stress may be resolved into two equal principal stresses. with the mutually perpendicular directions rotatable around the axis of the cylinder. Fig. ib shows stress combinations with Sz equal to The greatest principal stress is in the axial direction, and the stress combination tends to cause either absolute or relative increase in length.* Fig. u shows stress combinations with S2 equal to St. The greatest principal stress is in the radial direction, and the combination tends to cause either absolute or relative decrease in length. The complete representation of either technical cohesive strength, yield strength, or ultimate strength generally requires a three-dimensional diagram. When two of the principal stresses are kept equal, however, the strength of a metal may be represented by a two-dimensional diagram with the coordinates representing the axial and radial stresses.6-II In this paper, attention will be confined almost entirely to stress combinations with two of the prin-

Jan 1, 1945

By Herbert Clark Hoover, Lou Henry Hoover

GEORGIUS AGRICOLA was not only the author of works on Mining and allied subjects, usually asso ciated with his name, but he also interested himself to some extent in political and religious subjects. For convenience in discussion we may, therefore, divide his writings on the broad lines of (1) works on mining, geology, mineralogy, and allied subjects; (2) works on other subjects, medical, religious, critical, political, and historical. In respect especially to the first division, and partially with regard to the others, we find three principal cases : (a) Works which can be authenticated in European libraries today ; (b) references to editions of these in bibliographies, catalogues, etc., which we have been unable to authenticate ; and (c) references to works either unpublished or lost. The following are the short titles of all of the published works which we have been able to find on the subjects allied to mining, arranged according to their present importance :-De Re Metallica, first edition, 1556; De Natura Fossilium, first edition, 15,46 ; De Ortu et Causis Subterraneorum, first edition, 1546; Bermannus, first edition, 1530 ; Rerum Metallicarum Interpretatio, first edition, 1546; De Mensuris et Ponderibus, first edition, 1533; De Precio Metallorum et Monetis, first edition, 1550 ; De Veteribus et Novis Metallis, first edition, 1546; De Natura eorum quae Effluunt ex Terra, first edition, 1546 ; De Animantibus Subterraneis, first edition, 1549. Of the " lost " or unpublished works, on which there is some evidence, the following are the most important:-De Metallicis et Machinis, De Ortu Metallorum Defensio ad Jacobum Scheckium, De Jure et Legibus Metallicis, De Varia Temperie sive Constitutione Aeris, De Terrae Motu, and Commentariorum, Libri VI. The known published works upon other subjects are as follows:-Latin Grammar, first edition, 1520; Two Religious Tracts, first edition, 1522; Galen (Joint Revision of Greek Text), first edition, 1525 ; De Bello adversus Turcam, first edition, 1528 ; De Peste, first edition, 1554. The lost or partially completed works on subjects unrelated to mining, of which some trace has been found, are:-De Medicatis Fontibus, De Putre¬dine solidas Partes, etc., Castigationes in Hippocratem, Typographia Mysnae et Toringiae, De Traditionibus Apostolicis, Oratio de rebus gestis Ernesti et Alberti, Ducum Saxoniae.

Jan 1, 1950

By L. L. Oriard

In order to predict the influence of blasting on slopes, one must first understand the action of explosives, the manner in which rock is broken or displaced, and how seismic waves are transmitted, and the nature of these seismic waves. In this paper, the author describes the action of high explosives on rock masses, beginning at the source of the explosion, extending through the zone of rupture to a distance where only elastic waves of low energy persist. The paper describes the relationships between explosives charge quantities and distances, including the character and intensity of the seismic waves in various types of terrain. In looking at the analysis of slopes subjected to seismic waves, it has been common practice to assume a simplified model in which the anticipated acceleration is applied horizontally to the slope as an equivalent static force, or a model in which there is a rigid base subjected to mechanical shaking. Such models do not accurately portray blasting activity taking place within or near the slope in question. In dealing with blasting effects, it is important to under- stand seismic wave types, wave lengths, attenuation and transmission paths, as well as vibration intensity. In most cases, those slopes that are the least stable under static loading will also be the least stable under dynamic loading, although there may be rare exceptions. Thus, the more that is known about a slope statically, the better will be the assessment of it dynamically.

Jan 1, 1983

By C. A. Heiland

For a long time it has been known that it is possible to deduce conclusions about the physical constitution of the interior of the earth from the records of natural earthquakes obtained by stationary seismographs. In view of this fact it is surprising how late, relatively speaking, geologic prospecting by seismic methods has been taken up, although the first suggestion was made 40 years ago- that travel-time curves of artificial explosions might be used for the study of the change of the velocity of seismic waves as depth. Further suggestions of practical applications of artificial explosions for geologic purposes were made by Belar,2 by von dem Borne,3 by Benndorf4 and by Galitzin,5 but it was not until 1919 that Mintrop obtained. a patent on the seismic prospecting method which he has applied commercially on a large scale ever since. Dr. Mintrop came to this country with his method at about 1923. Since that time, several. American oil companies have developed seismographs of the mechanical type for the vertical component similar to that of Mintrop's (Humble Oil Co., Dr. Ricker). Other consulting geophysical companies designed other types of seismic devices, the simplest of them for the recording of the first impulse being the geophone (McCollum Geophone Co.). The galvanometric recording method as first proposed by Galitzin is being used (Geophysical Research Corpn.?) and use is being made even of the piezoelectric properties of crystals for portable seismographs (F. Rieber).. There is such an enormous variety of all kinds of portable seismographs, vibrographs, accelerographs, etc., that it is difficult to decide just what kind is preferable. Unfortunately, nothing has been published as yet about American designs of portable seismographs, except the Wood Anderson torsion-seismometer. After Mintrop's design of portable seismographs, other constructions were made.

Jan 1, 1928

By Otto Wartenweiler

AFTER the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities with some decomposed andesite, while the average value of mill heads were calculated to be $20 plus in gold, no silver being present. The tonnage to be treated at ,the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities, for increasing the capacity to 400 tons. . While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to properly receive the run-of-mine material, which was too coarse for a No. 5 crusher. To accomplish the coarse grinding to. best advantage, a careful comparison was made between the modern steel ball mill-the last word in crushing and grinding-and one of its older, and, at that time better-established, competitors, the rolls.' The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball mills because a simpler arrangement is possible, and1 because. the handling of, ball mills is preferred by the operator.

Jan 11, 1917

By A. Perry Thompson

I. GENERAL DISTRIBUTIONS APPEARANCE, AND RELATIONS MINING in Butte has seldom encountered covellite in commercial quantities. The notable occurrences, extending vertically and laterally perhaps several hundred feet, presented scattered, bladed lenses of this mineral in a matrix of quartz, pyrite, enargite, bornite, and chalcocite. But under the microscope covellite is seen to be widespread in the Butte ores, though in such small quantity that megascopic examination will not discover it. In early mining operations covellite was found in the Gray Rock vein, a member of the Blue vein system. As described by Sales,1 it persisted as an occasional ore mineral, associated with quartz, pyrite, tetrahedrite, bornite, chalcocite, and minor amounts of sphalerite, from the 700-ft. to the 1,200-ft. level of the East Gray Rock and Diamond mines. Crushed quartz-monzonite and later quartz completed the vein filling between

Jan 4, 1915

By Reynold Q. Shotts

Data are presented which show that fractions of varying densities-from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals.

Jan 1, 1950

By Paul Tyler

STRATEGICALLY situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority's research program has led to quasicommer-cial operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennesse's phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1, 1938, was approximately 19,000,000 tons. Official estimates of reserves are overly conservative and evidence submitted before a joint Con-gressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1939

By Frank Rieber

THE discovery that strongly magnetic bodies localized near the surface of the earth could be detected by the distortion which they produced in the resultant magnetic field marked the beginning of magnetic surveying methods. From an original ability to detect bodies of magnetic iron ore and the like when located very close to the, surface, these methods have been extended until today they promise to give much information with regard to the structure of such slightly magnetic material as sedimentary rock containing only a very small proportion of iron.1 The recent extensions have been made possible through the development of more delicate instruments, and of methods for their use. From the original compass and dip needle, the design of apparatus has progressed until equipment Is typified by magnetic balances capable of measuring the components of the earth's field to an extremely high degree of accuracy. It seems unlikely that the limit of such instrumental development has been reached. Just as the change from compass and dip needle has enabled the location of relatively minor changes in magnetic materials, so additional developments in the direction of increased sensitivity, as well as in greater dependability and constancy of operation, should reveal positively many slight changes which either escape notice in the present surveys or are so small that they cannot with certainty be separated from uncontrollable errors due to inconstant operation of the equipment. The ability to read smaller and smaller variations does not mean, of course, that deductions as to the causes of these variations will be made as accurately and definitely as -is possible with the more pronounced anomalies.

Jan 1, 1928

By AIME AIME

THE list of deaths during the year 1906 comprises the following names, the figures in parentheses indicating the year in which the persons named were elected to membership Members and Associates.-Arthur Vaughan Abbott (1882), William Anderson Akers (1889), R. Scott Allen (1905), George H. Arlett (1900), Thomas Septimus Austin (1883), Thomas T. Baker (1887), William Tittley Batchelor (1902), Charles Lowthian Bell (1897), Edgar Vallentine Bensusan (1892), George Lothrop Bradley (1874), Ernst Elmer Breisch (1896), Horace F. Brown (1895), James A. Burden (1876), Alexander B. Coxe (1880), George A. Crocker (1879), Albert W. Fiero (1886),

Jul 1, 1907