Search Documents

By Karl A. Bauer, Cornelis Bezemer

The deposition of calcium carbonate scale on surface and subsurface production equipment creates an operation problem in many oil fields. The formation water in which the carbonate-scale-forming components are initially dissolved becomes supersaturated with calcium carbonate as a result of the drop in pressure during production. The continuous flow of a supersaturated solution through the production equipment results in the growth of a dense layer of calcium-carbonate crystals. For a scale layer to be built up, the supersaturated formation water should contact the walls of the production equipment. The tendency for scale to be deposited, therefore, will be low, if the crude has a low water cut and if the water is finely dispersed in the oil. A scale problem will occur, if at a high water cut part of the water is present as free water. The rate of scale deposition will then be approximately proportional to the rate of free water production. Depending upon where the formation water becomes supersaturated, scale may be deposited in the flow line only, in both flow line and tubing, and in some cases even in the perforations and in the formation near the wellbore. In the South Sumatran fields (Indonesia) the main difficulties encountered due to the deposition of calcium-carbonate scale have been restriction of flow through tubings and flow lines, wear and abrasion of plungers and liners, and stuck plungers or wellhead valves. So far, the only methods of combating the *Presently associated with Brunei Shell Petroleum Co., Ltd.. Seria. scale problem have been routine acidizing and additional well pulling. As for the pumping wells, it was estimated that some 50 percent of the total well-pulling effort was directly attributable to scale deposition. The most promising alternative was to prevent the deposition of calcium carbonate scale by means of chemicals. Inorganic polyphosphates such as sodium hexametaphosphate and trisodium polyphosphate are known to retard the formation of scale by the "threshold action". They are adsorbed on specific faces of the crystal nuclei and thus prevent crystal growth, thereby stabilizing supersaturation. Polyphosphates are effective at very low concentrations ( a few ppm), and far less than stoichiometric quantities are required to keep the scaling ions in solution. Recent investigations on barium sulfate scale1 have confirmed this mechanism. The types of polyphosphate mentioned can be applied as concentrated aqueous solutions either squeezed into the formation, lubricated down the annulus or injected via macaroni string. Several squeeze jobs with polyphosphate solutions have been carried out in the South Sumatran fields, however, with disappointing results. Lubrication down the annulus and injection through a macaroni string were not considered attractive in this area because of the kind of equipment and the degree of supervision these techniques require. Polyphosphates are also available in a granular, glassy form, which, in contrast with the readily soluble types already mentioned, show an extremely low

Jan 1, 1970

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46" 31' north latitude, 67" 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sul-fide deposits of the Bathurst-Newcastle district. The helicopter electromagnetic equipment located an anomalous conductive area, coincident with a small aeromagnetic closure, about five miles west of the town of Juniper. Subsequently 30 mining claims (total area about 6600 x 8000 ft) were staked and company personnel conducted geological, geophysical, and geochemical investigations on the property. The claims and immediately contiguous areas were mapped geologically, and an area of about 2000 x 4000 ft was soil-sampled and also surveyed by ground electromagnetic and gravity methods. Finally six diamond drillholes, totaling 3500 ft in length, were drilled to test the anomalous conditions discovered by the several exploration techniques used. The discovery of base metal sulfides during drilling was a technical success for the exploration methods, but the quantity of sulfides was too small to be profitably exploited.

Jan 1, 1959

By L. A. Roe

Magnetic separation of iron ores is one of the fastest-growing segments of the minerals beneficiation industry. The tonnage of taconite ores processed annually by magnetic separation will, in a few years, reach 100 million. Magnetic separation occupies an attractive position in the field of ore beneficiation. It is a simple yet effective method, used for some 150 years and steadily growing more important. This type of beneficiation orginated in 1792, when William Ful-larton was issued a British patent covering the separation of iron ore by magnetic attraction. What is magnetism, and why are some materials capable of being magnetized and others not The study involves many unknowns, and even a partial answer to these questions would be a dissertation in solid state physics and perhaps other fields of science. But the last two decades have revealed basic facts as to why certain materials are magnetic and what happens to them when they are magnetized. Some of the newer studies in solid state physics have developed a theory that can be applied to studies of magnetism. It is claimed that magnetism stems fundamentally from the spin of electrons in atoms that tend to go in pairs, spinning in opposite directions. The atom as a whole can act as a magnet only when there is an imbalance of electronic spin. Whenever an atom has an odd number of electrons, therefore, this imbalance exists. This neutralizing effect explains why a piece of material that contains atomic magnets is not necessarily magnetic. The physicists tell us that iron is composed of many small magnetized regions called domains, which consist individually of millions of atoms. The piece of iron becomes magnetized when an external force lines up these domains in the same direction. Fundamental data developed by physicists working in fields far removed from minerals beneficiation are now available for developing better magnetic separators for ore processing. More Data Needed on Magnetic Properties of Minerals: There is less information on magnetic properties of minerals than there is for certain aspects of magnetic separator design. When the data on magnetic properties is available, it is often directed toward the study of powders for tape recorders and other highly scientific endeavors that are of little use to the beneficiation engineer. W. R. Crane's table of tractive forces, published in 1902, is still a guide in the study of magnetic minerals. Bits of other information regarding electrostatic conductivity, dielectric constant values, and permeability of various minerals have also appeared but are of small practical value in magnetic separation of ore. It is extremely important to obtain pure mineral specimens for making investigations and to record results that may be of use in studies of magnetic processes. Reference to the large volume of data developed by those concerned with analysis and design of permanent magnets soon reveals that these people have extensively evaluated the effect of various impurities on magnetic properties. Much of the science of the ferrite industry is based upon spinel-type structures which are varied by substitution of selected elements or even subtraction of elements, leaving vacant sites in the space lattice. Magnetic separators are used to beneficiate a wide variety of industrial minerals. In this application the relatively large volumes of nonmagnetics are usually the commercial products. The amount of mag-

Jan 1, 1959

By H. W. Fleming, R. R. Brooks

The Clearwater Deposit, a small occurrence of massive-sulphide mineralization enclosed in an envelope of disseminated-sulphide mineralization, was discovered as a result of an aeroelectromagnetic survey in New Brunswick in 1955. Subsequently, additional flights were made over the deposit and various ground follow-up methods were employed to ascertain the nature of their response. All methods proved to be capable of indicating the occurrence with varying degrees of precision. This paper is a presentation and a discussion of the magnetic and electromagnetic data, both airborne and ground, and the self-potential data obtained over this deposit. The attention of Canadian mining exploration companies was initially focussed on New Brunswick by the discovery, in 1953, of the Brunswick ore body. Ground electromagnetic surveys were of considerable assistance in locating and developing this deposit. In the following year, 1954, the Heath Steele base-metal deposits were discovered by employing an airborne electromagnetic device and ground electromagnetic surveys to follow-up the airborne indications. These discoveries demonstrated clearly that both airborne and ground electromagnetic techniques were applicable for locating the near-surface deposits of massive sulphides present in this region. Airborne electromagnetic equipment became available on a contract basis through Aeromagnetic Surveys Limited early in 1955 and was used extensively thereafter throughout a large portion of northern New Brunswick. It was as a result of one of these surveys with Aeromagnetic Surveys Limited equipment in the summer of 1955 that the Clearwater Deposit was detected. The airborne anomaly was located on the ground by means of an electromagnetic survey using a Swedish Slingram unit. During 1956, the region was investigated more thoroughly- in the hope that other sulphide bodies might be located. Airborne electromagnetic coverage was extended and the Clearwater Deposit itself was used as a testing ground for the various methods and types of equipment currently in use in New Brunswick. In this paper com prative data are presented for the airborne magnetic, airborne electromagnetic, ground magnetic and ground electromagnetic surveys over this deposit. The ground electromagnetic instruments used were the McPhar vertical-loop unit and the Slingram and Boliden horizontal-loop units. Self-potential surveys were carried out with a McPhar unit. From the geophysical point of view, all ground electrical methods employed indicated the presence and the extent of the massive-sulphide mineralization with a good degree of accuracy. The horizontal-loop methods however, defined the contacts more precisely as is to be expected when dealing with a flatly-dipping

Jan 1, 1961

By M. M. Singh, J. W. Brown

Three rocks of highly varied physical properties are selected for the first reported experimental study concerning microseismic activity of rock under tension to determine the effects of static fatigue, loading rate, repeated loading and rock anistropy compared to compression and bending loads. The microseismic method of detecting rock under deformation may be a great potential tool in surveillance and location in situ of dangerously stressed strata, as well as predicting rock failures. Noises emitted under load or the rate of energy (energy of noise pulses generated per unit time) are computed for varying conditions. The tests are conducted at constant load on a dead weight loading machine to eliminate all possible extraneous noises — an indispensable precaution — at various load levels. Experimental results are reported including the relation of total energy emitted to tensile strength of rock and the possibility of simulating a phenomenological model for microseismic activity. Plots of some of the experiments are included. INTRODUCTION Rock failure, whether on a large scale faulting in the earth's crust and rock bursts in mines, or on small scale ruptures of laboratory test specimens, generates transient vibrations in the rock mass. Mechanisms of intermittent deformation, such as twinning and cracking through and between mineral grains, also produce similar vibrations, but of very small amplitude. Such vibrations from both deformation and failure are referred to as microseismic activity, rock noise, or occasionally seismo-acoustical activity. An individual rock noise is sometimes

Jan 1, 1967

By Y. C. Liu

Both the habit plane of martensite and the orientation relationship between the matrix and martensite platelets of different habit planes have been investigated in binary titanium alloys with molybdenum, chromium, and iron. The effect of the mode of deformation on the martensite habit plane was studied. A micrograph of an exposed mar-tensite platelet is presented. IN the study of martensitic transformation in Ti-Mn alloys,' two martensite habit planes—{334), and {344)8—were reported. The {334), habit was also observed in unalloyed titanium upon transformation,' although there is disagreement with respect to the exact indices. The other habit plane, {344),, has not been reported in martensitic transformation in any other alloys. The present investigation was made to determine whether other binary titanium alloys with P-stabil-izing elements would exhibit a crystallography of transformation similar to that of Ti-Mn alloys. Furthermore, since martensite platelets can be induced by deformation under certain conditions, it was of interest to investigate whether the mode of deformation, compressive or tensile, would influence the formation of martensite platelets on a specific plane in an alloy system which possesses two martensite habit planes. Experimental Procedure The material used for the preparation of the binary alloys of iodide titanium with molybdenum, chromium, and iron had the following purities: 99.99 pct iodide titanium, 99.9 pct molybdenum, 99.423 pct chromium, and 99.9 pct iron. The compositions of alloys listed in this paper are in nominal weight percentage. All specimens used were prepared and treated according to the procedure described in reference 1, unless stated. For the subzero temperature treat,ment the following experimental schedule was followed. After specimens had undergone the grain-growth treatment, they were quenched into an ice-water bath and were then metallographically examined. In specimens of higher alloy content, no martensitic transformation was observed. In those in which mar-tensitic transformation did occur, only specimens in which the martensite platelets existed as fine needles in localized regions were used. All specimens were reannealed 17 hr at 1200°C, quenched into ice water. and the capsule was broken. They were held in the ice water for from 5 to 10 sec, then transferred to a liquid-argon bath. This stepped quenching procedure was found to be more efficient than direct quenching into liquid argon. In the latter case, as soon as the hot specimen was immersed in the liquid argon, a protective, insulating layer of argon gas formed, and the specimen continued to glow vividly in the bath for some time. In the study of the habit behavior of martensite produced by deformation, specimens were deformed at room temperature either by compression, tension, or rolling. Martensite habit planes were determined by the two-surface analysis procedure described in reference 1. A stereographic net of 153/4 in. diam was used throughout the investigation. The method for determining the orlentation relationship between martensite and the matrix follows that used by Greninger and Troiano.' A diamond-polishing table with its auxiliaries was used in order

Jan 1, 1957

By Fred H. Perfect

The thermite process, now approximately 80 years old, has heretofore been practiced in ceramic vessels. This paper outlines the successful production of several million pounds of alloy produced in zuater-cooled copper vessels. THE high temperatures necessary to produce fluid high-alumina slags have probably discouraged earlier workers from attempting to utilize water-cooled vessels. The following is a report of the successful application of this method, together with a report of the physical and chemical problems which had to be solved to make the process practical. About 1955, when Reading Alloys was more concerned with the production of ferrotungsten than with most other types of alloys, it was found to be exceedingly difficult to predict the reaction rate that one would experience from one tungsten ore to another . This difficulty was increased for two reasons: the physical state of the ore as received was seldom uniform, and the size of the mass to be reduced is a very important factor in developing the proper mix for the final reaction rate and temperature. For example, the reduction of ferric oxide with aluminum would theoretically produce temperatures of about 2600°C, and, in spite of the losses due to radiation, the energy is quite sufficient to produce a very fluid slag and iron effecting a very clean separation. On the other hand, the reduction of ferrous oxide with aluminum, while it is not as energetic as the first reaction, nevertheless should give temperatures above 2000"C, which should cause separation of alumina and iron, but, in practice, this is not the case and good fluid slag is not obtained. The heat of reaction, calculated from the thermo-dynamic heats of formation of the constituents of the reaction, offers a convenient guide to the feasibility of a thermite reaction. Thus, the values listed in Table I can be used as an approximate guide for estimating the results which may be expected in the reduction of various oxides and combinations of oxides using aluminum as the reducing agent. As a generalization, those reactions releasing approximately 600 cal per g of total mass represent the lower limit at which to expect separation of slag and metal. On the other hand, those reactions which release 1100 to 1200 cal per g are too violent to be used successfully without the addition of considerable inert material, such as lime, fluorspar, and so forth. Reaction rate is also a very important factor. This, of course, is governed very largely by the sizing and intermingling of the oxidant and reductant and by the starting temperature of the reactants. This is why those figures shown in Table I can only be a general guide. Further, it must be understood, that by adding powerful oxidizing agents, such as nitrates, chlorates or metallic oxides, such as molybdenum trioxide or chromium trioxide, certain problems respecting low temperatures are not necessarily solved. This is true in the addition of oxidants, such as sodium chlorate. By adding too high a concentration of sodium chlorate as a booster for a particular reduction, explosions are generated. Generally, they are of an intermittent type so as to give a Roman Candle effect to the reduction itself; with each surge resulting from a minor explosion more and more material is thrown

Jan 1, 1968

By J. M. Toguri, K. Grjotheim

It is known 1,2 that the equilibrium between titanium metal, TiCl2 , and TiCl3, in a solvent of molten metal chlorides, is influenced both by the total amount of dissolved titanium and by the type of solvent. Assuming that the trivalent titanium forms the complex ion Ti111 Cl4, the equilibrium reaction may be expressed by the following equation, (Me) TiIII cl4+ 1/2 Ti = 3/2 TiII cl2+ (Me) Cl The ideal ionic equilibrium constant for this reaction is, Where the N's are the molar ionic fractions in the equilibrium melt, and (Me) the different types of cations present in the equilibrium mixture. The following thermodynamic relation is derived between Kand the concentration of cations in the equilibrium melt, mix The N"S are the equivalent ionic fractions, and so forth are constants corresponding to the standard changes in free energy for reactions in melts where only the cation indicated is present, and f (y1) is a function of the activity coefficients in the equilibrium mixture. When this term vanishes, a simplified linear relationship between In Kideal and the concentration is obtained. The simplified relationship has been applied with satisfactory results to the experimental data of Mellgren and pie,' and Kreye and Kellogg.2 MANY existing methods for the production of light metals involve the reduction of their respective metal halides in the presence of salt melts composed of alkali or alkaline earth chlorides. In such a solution phase, the light-metal halide may undergo stepwise reduction from a higher, to a lower valence, and finally to a zero valent state. In this connection, the disproportionation equilibrium is of great interest. In the case where the higher valence is three and the lower valence is two, the disproportionation equilibrium may be written as follows, 3 Me11 = 2 Me111 + Me [I] If this equilibrium occurs in a salt melt containing a large excess of alkali chlorides, a typical ionic melt is obtained. It is then possible to formulate the cation equilibrium: 2 Me+h' + Me = 3 Me++ [II] Reaction [11] is analogous to a cation exchange reaction. It has been shown thermodynamically that the equilibrium constant for such a reaction in 2

Jan 1, 1960

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By T. Sekimoto, T. Kokubo, M. Yamamoto, K. Masuda, T. Moro, H. Sakamoto

The choking-free cyclone was developed primarily to remove solid particles suspended in a slurry containing fibrous materials, such as municipal solid waste. This cyclone is characterized by a screw conveyor at the underflow side of the cyclone. The screw conveyor has a hollow rotational shaft for air supply and is driven by a variable speed motor for discharge control. Even if the underflow discharge is highly concentrated, this type of cyclone can be stably operated without nozzle choking. High classification efficiency similar to that of a conventional cyclone can be obtained as a result of air introduction through the hollow rotational shaft. The recovery of organic matter and the removal efficiency of inorganic matter were actually improved by the application of this cyclone to municipal solid waste. After applying this cyclone to the desliming of fine sand, sand product of low water content was recovered.

Jan 1, 1980

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1936

By R. L. Grunes, F. K. Kies, C. D&apos, Antonio

THE several studies concerned with the annealing of thin nickel films have largely been restricted to films of a single thickness.1-4 It is well-known, however, that both physical and mechanical properties depend upon film thickness.5, 6 The strength-thickness relations found in vapor-deposited nickel films in the annealed and as-deposited states, as an example, are at least partially due to the density and arrangement of imperfections within the films.7, 8 For these reasons, the annealing characteristics of thin nickel films as a function of thickness were investigated. Electrical resistance was chosen to monitor annealing behavior since resistance changes are partially dependent upon defect structure. In addition, the equations predicting film resistivity as a function of thickness are already available.9, 10 Further advantages afforded by electrical-resistance measurements are its adaption to continuous readings during annealing and its relative simplicity. Nickel films were vapor-deposited, at average rates of 60Å per sec, on Vycor substrates held at room temperature in vacuums of about 10-5 torr. Afterwards, deposition-thickness measurements were made using a multiple-beam interferometric technique. A more detailed description of deposition procedures and the interferometer appear elsewhere.7, 8 The four-probe method was employed in measuring electrical resistance since this technique measures film resistance without contributions from lead wires and contacts. Resistance measurements were made before, during, and after annealing to temperatures of 700°C under vacuums of approximately 10-4 torr. Measurements were made every 25°C or more often when necessitated by unusual resistance changes. Cooling and heating rates were maintained at approximately 5°C per min. Typical resistivity vs temperature curves are shown in Figs. 1 through 4. It is apparent from these

Jan 1, 1965

By T. K. Perkins, L. R. Kern, R. E. Wyant

Many factors influence the results of hydraulic fracturing to stimulate well productivity. Most of these factors have been studied and their effects discussed in the literature. However, the movement of sand through the crack during fracturing has received little consideration. Exactly where the sand goes in the fracture, how it gets there, and how this might influence results have not been studied, judging from published reports. To get an answer to some of these questions we have studied sand movement through a simulated crack segment in the laboratory. Although the work is preliminary, we have answered some questions about sand movement in a semiquantitative sense. We are reporting our results at this time in the hope of stimulating interest and further study in this important aspect of fracturing. LABORATORY EXPERIMENTS Fig. 1 is a schematic diagram of equipment used in this study. A segment of a vertical crack 0.25-in. wide was formed between two Plexiglas plates, and movement of sand in fluid through the crack was observed under various conditions. Sand and fluid were injected into the crack at constant rates. The top and bottom of the crack were closed so that the fluid flowed horizontally. Because of gravity most of the sand settled to the bottom before moving very far through the crack. If the fluid velocity exceeded a certain critical value, then all the sand injected was washed on through the crack even though it had settled to the bottom. When the fluid velocity was less than this value when sand injection was started, most of the sand which settled in the crack remained in place until enough of the area open to fluid flow was blocked by the settled sand to increase the fluid velocity to the critical value.. At this point all injected sand moved on through the crack even though it settled to the lower portion of the moving fluid section. All sand previously settled remained in place. When fluid velocity was increased at this paint by increasing fluid injection rate (without also increasing sand injection rate), some of the previously settled sand was washed out until enough area was open to flow that the velocity dropped to the critical value. Conversely, when the fluid velocity was decreased by decreasing the fluid injection rate (without changing the rate of sand injection), additional sand would settle until the critical velocity was again attained. In short, the critical velocity is an equilibrium value which the system will automatically seek, if possible. The equilibrium (or critical) velocity was measured under several conditions. The results of these measurements are shown in Pig. 2 where the equilibrium velocity is shown as a function of the amount of sand injected per minute. The points falling in the shaded band shown in Fig. 2 were obtained with water. The higher viscosities were obtained by adding CMC (carboxymethylcellu-lose). Data indicate that the equilibrium velocity is not very sensitive to sand size or transport fluid viscosity, or to sand injection rate (except at very low rates). Points connected by the solid CUrve in Fig. 2 were obtained with water and 20- to 40-mesh steel shot. The equilibrium velocity is apparently fairly sensitive to difference in density between particle and fluid. Only one run was made with a gelled fluid and that was gelled water at zero sand injection rate as shown in Fig. 2. (Measurements of equilibrium velocity at zero sand injection rate were made by filling the crack

By C. G. Dunn

James, Jones, and Leak (JJL) conclude that growth-rate and orientation-distribution data obtained in a steep thermal gradient should be used with caution to account for isothermally produced recrystallization textures. I agree. However, it is not clear whether they conclude a) that the orientation dependence of rate of growth of secondaries in (commercial) silicon iron depends on both temperature and a temperature gradient or b) that, in applying rate data obtained in a steep thermal gradient, the isothermal annealing temperature must be close to the temperature for which the rate data apply. Also, it is not clear what tem-

Jan 1, 1967

By T. G. Sieber, T. D. Tiemann

The extraction of quartz from siliceous iron ores by dissolution in sodium hydroxide solution has been described in detail in AIME Transactions. l923 data reported covered the temperature range from 230-416°F, where a continuous increase in the amount of silica extracted with increase in temperature was found. It is the purpose of this paper to describe some unexpected results of more recent work exploring principally the range of 500600°F where higher rates and greater amounts of silica extraction were antici-p ted. In brief, the experimental procedure consists in digesting the ore under pressure in solutions of sodium hydroxide, filtering the suspension and weighing and analyzing the dried residue for iron content. The amount of extraction is calculated from the weight loss or from the iron analysis of the residue and that of the original ore.

Jan 1, 1969

By J. Douglas, W. T. Ford, G. E. Henderson, I. F. Roebuck

An implicit numerical method is presented for simulating the differential and algebraic relations governing one-dimensional three-phase flow in porous media. The method is based upon compositional representation of the hydrocarbon system. Variable physical properties and water-oil capillary forces are included in the formulation; however, the effect of gravity is ignored. The effects of changing composition and mass transfer are considered through the use of known phase behavior concepts and correlations. The differential and algebraic equations and the numeric approximations to these equations are presented, and the computing algorithm is discussed in detail. This method is used to simulate a single-phase, two hydrocarbon-component gas displacement laboratory experiment. The method is also applied in simulating a solution gas drive and a gas injection problem using a reservoir oil represented as a nine-component mixture. For comparative purposes, the latter two problems also are examined with a one-dimensional volumetric model. The results of the simulation of the laboratory experiment demonstrate the relevance of this method to problems wherein the effects of mass transfer significantly enter the displacement process. The comparison of the results of the volumetric and compositional methods applied to a reservoir system illustrates not only the advantages and benefits derived from examining the hydrocarbon system composition, but also the necessity of this approach in application to a general reservoir problem. INTRODUCTION The advent of large memory, high-speed digital computers enabled reservoir engineers and mathematicians to pool their knowledge in the development of sophisticated techniques for the prediction of oil and gas reservoir performance. These techniques have progressed from volumetric and trend analysis calculations to the development of "mathematical models", or reservoir simulators. These latter models, in general, utilize finite difference approximations to the rather complex partial differential equations that mathematically describe the physics and thermodynamics of fluid flow in porous media. Many forms of this "model" type are available today, and much of the recent literature has been devoted to either improving known methods or developing new techniques for use in these prediction methods. The more advanced techniques in use at this time consist of the solution of differential and algebraic relations that describe a reservoir geometry in one, two or three dimensions and that incorporate reservoir hydrocarbon and water fluid systems that obey specified physical laws, having properties that might easily be measured in the laboratory. This type of model utilizes formation volume factors and other volumetric data, expressed directly as functions of pressure, to represent the reservoir fluid system. Experience gained with this type of simulator, commonly known as a "beta-factor model", has indicated that the approach has many outstanding defects, most of them due to the assumption that those properties measured in the laboratory completely describe the behavior of the fluid system throughout the life of the project under study. The effects of varying hydrocarbon composition and mass transfer between the phases of this hydrocarbon system must, by definition, be ignored. These defects, which may often be ignored in

Jan 1, 1970

By J. C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert,1,2 Russell,9 Le Conte,4 Spurr,5 Louderback,8 and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea. More recent syntheses of the geologic history have been prepared by Lindgren,7 Ransome,8 Nolan,9 Bill-ingsley and Locke,30 Longwell,11 and Eardley.12 The tentative nature of the present interpretation, which treats the structural evolution of the Utah and Nevada area, must be considered in light of the scarcity of geologic information from the province as a whole. The methods of interpreting tectonic history from stratigraphy are based largely on the concepts of Marshal Kay.23 Discussions with Hoover Mackin also have aided in organizing the Tertiary history. TECTONIC AND STRATIGRAPHIC SETTING Two approaches to the subject of the tectonic history are possible; they correspond to looking through opposite ends of a pair of binoculars. One involves an expansion and extension of detailed work and the other an interpretation based on regional geological relationships. It is believed that the second approach, used here, is not in disagreement with detailed observations. The area of the Basin and Range Province is shown in Fig. 1. Within this area middle Tertiary to Recent high-angle faulting has controlled development of mountain ranges and valleys. Only the part of the area north of Las Vegas, Nev., and south of the Snake River in Idaho will be considered in this article. Within this part of the province most of the ranges trend north-south. Approximately two thirds of the area is covered by late Tertiary to Recent valley fill and lake deposits.

Jan 1, 1961