Search Documents

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By João Luiz do Vale

In standard wear tests, such as pin on disk (ASTM-G99) or block on ring (ASTM-G77), the apparatus simulates conditions that are often different from a machine element real application. Therefore, for an accurate investigation of a tribological application, it is essential to test the real condition in which there are similarities as: geometry, contact details, force application mode, materials, among others. It emphasizes that for studies involving polymeric materials it becomes extremely relevant. Thus, the Laboratory of Surfaces and Contact (LASC) at UTFPR developed an apparatus for sliding bearing on shaft test. In that equipment, loads are applied by a dead-weight system and the frictional force is measured on a load cell. The apparatus operating ranges for load added to the dead weight system and rotation shaft are from 0.2 to 5.0 kgf and from 260 to 3500 rpm, respectively. This paper presents a detailed evaluation of such apparatus, which includes free-body diagrams analysis and a deduction to obtain an equation for the kinetic friction coefficient. Also, the standard measurement uncertainties of a caliper, an electronic scale, and a cell load were determined. It was verified that the kinetic friction coefficient equation is dependent on the apparatus geometry, the applied load, and the frictional force value. Additionally, through the statistical significance analysis it was concluded that some terms in the equation were not significant. Finally, through the application of the error propagation theory in the kinetic friction coefficient equation, the standard measurement uncertainty of the apparatus which showed a value nearby 0.002 along the operating range of the apparatus was obtained.

Jul 31, 2018

By Patrícia Mundim Campos Faria

The process of particle size reduction by grinding is inherently inefficient and involves high capital and operating costs. In particular, ball milling is one of the important unit operations in the iron ore pelletizing process. The mill product, due to its physical properties, determines the efficiency of subsequent stages of classification, filtration and pelletizing, thus impacting the quality of iron ore pellets. The work demonstrates the application of the population balance model in the optimization of a full-scale ball mil circuit grinding pellet fines with the aim to evaluate the optimal solids concentration to improve iron ore pellet quality. Initially, detailed experimentation was carried out in a 25.4 cm diameter batch mill and a relationship for mill scale-up using a linear population balance model in wet grinding systems was established. The selection and breakage parameters and the specific selection functions were determined for pellet feed iron ore. It was possible to identify the non-normalizable nature of the breakage functions of the ore studied, which were modeled properly. Afterwards, as a result of incorporating the specific selection functions and breakage functions into the linear population balance model, it was possible to predict product size distributions in the pilot and plant scale mills (0.416 and 5.18 m diameter, respectively) from data obtained in the 25.4 cm diameter mill. Finally, with this scale-up procedure it was possible to appraise the plant scale optimization via laboratory scale grinding mill tests. The effects of changing percent solids were assessed in order to improve the industrial mill performance and the optimal value should be in the range from 76 to 80%.

Aug 1, 2018

By Zou Zhongpping

Under the new normal state, blast furnace outputneeds to be adapted to the market demand, however the limitation in blast furnace output has significant impact on blast furnace operation and is prone to cause inactive furnace hearth and higher fuel ratio. To address such problems, some practices to maintain stable and smooth operation of blast furnace in case of output limitation are proposed based on data analysis philosophy, which allows the blast flow and hence the top pressure to be determined based on the hot metal output, and adequate kinetic energy of blast supply can be assured by adjusting the tuyeres. Matching between the oxygen enrichment and the pulverized coal injection is also proposed based on theoretical flametemperature, and burden distribution cycle calculation method is proposed, whichoffersnew approach for analyzing the change in burden distribution pattern.

Oct 30, 2017

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Breno Totti Maia

This work was a continuous and multidisciplinary development. Through studies of the blowing process and its parameters results, evolutions, improvements and adjustments were made on the lance’s hot face with Slagless® technology, as well in the process parameters and mitigating actions of the projection of materials out of the converter. The main results are the increase in the nozzle’s life with a “record mark” of 1785 heats, and water leakage occurrence in the cartridge decreased considerably reaching the mark of one year without any occurrence.

Oct 30, 2017

By Dr. Steven G. Jansto

The market demand for reduced fuel consumption and CO2 emissions in the automotive, energy and construction sectors have further increased the demand for new and advanced higher quality microalloyed grades produced via TMCP. The technological integration of the process and physical metallurgical advancements of value-added niobium (Nb) microalloyed thermo-mechanical controlled process (TMCP) steels continue to be developed and is an important element for these more demanding end user requirements and cost-effective steel production. The reheat furnace process step has a profound effect on the TMCP performance, final hot rolled steel quality and mechanical property consistency during the production of hot rolled steels. The uniformity of heating applied across the entire width, thickness and length of the slab or billet is essential in the successful achievement of consistent customer properties regardless of the chemistry. The resultant ferrite grain size in the final hot rolled product is significantly governed by the initial prior austenite grain size. However, the transition from laboratory melted and TMCP hot rolled heats to the production scale is often quite challenging. Aberrations in the reheating process step at the industrial furnace are often the root cause of mechanical property quality issues. These combustion process metallurgy parameters connect directly to the resultant TMCP product quality and is defined as Combustion Metallurgy

Oct 1, 2019

By José Fagundes Jr., Juliano Braz Possatti, Bruno Câmara Vieira, Gabriel Godinho Alves, Bruno Bastos da Silva Murad, Cristina Maria de Oliveira Roque

Driven by market trends, increasing environmental accountability, government regulations and fostered by the Company’s strategic plan, ArcelorMittal Tubarão has developed new steel products to deliver better solutions to fit each customer’s needs. This often translates in higher strength, more complex and dimensionally challenging (thinner and wider) steels to attend a broad array of goals, such as reduction of vehicles fuel consumption and carbon emissions, increase in fatigue performance of heat treated parts, higher load capacity per net weight in vessels or wagons and lower supplying lead time as ArcelorMittal Tubarão establishes itself as a domestic option for so far imported grades. Based on the annual Product Development Plan, a structured workflow involves technical discussions from an operational point of view about safety issues, metallurgical project, steel grade family definitions, offline simulations prior to field trials, deformation resistance and process parameters adjustments and scheduling strategy. As a result of the increasing synergy between the areas, the share of new materials developed in recent years has been sustainably increased up to 15% in 2018, adding value to the final product without impact on hot rolled coil output and with a low cobble index.

Oct 1, 2019

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Luis Armando Espitia

AISI 410 martensitic stainless steel specimens were low temperature plasma nitrided at 400°C in a mixture of 75%N2:25%H2, during 20 h. Active screen technic was used to avoid any edge effect The nitrided case is composed of expanded martensite (a’N) and e-Fe3N iron nitride, whilst chromium nitride precipitation was avoided. Surface hardness reached 1275 HV0.01. The transverse microhardness profile shows a gentle hardness gradient with a NHT nitrided case depth of 28 µm. Nanoindentation tests were carried out in order to assess the hardness (H), the Young modulus (E), the H/E and H3/E2 ratios and the elastic recovery (We) of both nitrided and non-nitrided specimens. The cavitation erosion mass losses were measured as a function of exposure time. The results showed a decrease of 27 times of the mass loss compared to the non-nitride specimens. Wear rate decreased from 2.56 mg/h for the non-nitrided condition to 0.085 mg/h after nitriding. The increment in the elastic recovery and the higher hardness values are responsible for the greater cavitation erosion resistance exhibited by the expanded martensite. Such results showed that low temperature plasma nitriding and the formation of expanded martensite are effective to increase cavitation erosion resistance of AISI 410 stainless steel.

Jul 31, 2018

By Flávia Vieira Braga

O efeito da temperatura de deformação a quente na textura cristalográfica de um aço inoxidável ferrítico AISI 430 estabilizado ao Nióbio foi estudado por ensaios de torção a quente. A laminação de acabamento em laminador Steckel foi simulada utilizando diferentes faixas de temperatura, buscando promover o amaciamento por recristalização. Após cada ensaio, as amostras foram temperadas até a temperatura ambiente objetivando a análise das microestruturas geradas. Foram também realizados ensaios de torção interrompidos visando avaliar a ocorrência da recristalização entre passes. A técnica de EBSD foi utilizada para analisar a microestrutura das amostras ensaiadas, a textura formada e o tamanho de grão. Foi observado que a de temperatura de simulação que mais favorece a ocorrência da recristalização estática está entre 900 e 840 ºC e o tamanho de grão resultante é menor em tais condições. A textura de torção obtida está em concordância com a literatura.

Aug 16, 2017

By Breno Totti Maia

Para uma boa operação das lanças de oxigênio para convertedores BOF é necessário existir uma boa condição de refrigeração, devido à agressividade existente no ambiente, onde ela fica exposta a condições de alta radiação, gases a alta temperatura e, algumas vezes, com o aço líquido. Para uma boa refrigeração, basicamente são necessários uma boa qualidade de água e condições adequadas de vazão e pressão. Mas somente esses fatores podem não garantir o desempenho adequado às condições de escoamento da água, devido à complexidade geométrica do bico da lança. Esse artigo tem como objetivo apresentar um estudo comparativo de escoamento da água, na parte crítica de uma lança que é o bico, destacando a importância da geometria interna do bico na troca térmica do equipamento. Serão apresentados os resultados comparativos, onde se observa que otimização do escoamento interno no bico da lança aumenta a vida útil do equipamento.

Jul 29, 2018

By Giselle de Mattos Araújo

A autorredução é afetada por características das matérias-primas tais como granulometria, porosidade, tipo e teor da fonte carbonácea, e também por características do ciclo de processamento imposto, taxas de aquecimento, tipo de atmosfera gasosa, temperatura média de processo. No presente trabalho objetiva-se, através de testes de termogravimetria, avaliar a cinética de autorredução e também o fluxo térmico associado, durante o processamento de diversas associações de finos de minério e fonte carbonácea. Com os resultados obtidos identificam-se condições que otimizam tanto a mistura autorredutora quanto o processamento, observando-se que em uma mesma faixa granulométrica, o maior conteúdo de Cfixo da fonte carbonácea e materiais mais reativos otimizam a cinética, em detrimento da maior quantidade volumétrica de partículas carbonáceas observada em amostras contendo carvões mais pobres em Cfixo. Taxas adequadamente controladas permitem a definição de instantes distintos para as diversas etapas fenomenológicas envolvidas no processamento da autorredução.

Aug 2, 2018

By André de Albuquerque Vicente

Foram estudadas as camadas de óxidos formadas nas superfícies de um aço inoxidável austenítico laminado do tipo 22.12, após oxidação ao ar a 800, 900, 1000 e 1100 °C, dentro de um projeto que visava uma melhor compreensão da oxidação a altas temperaturas ao ar de aços inoxidáveis resistentes a altas temperaturas. Utilizou-se o aço inoxidável austenítico microligado ao cério (253 MA®), que é um aço projetado para trabalhos a altas temperaturas. Várias técnicas complementares de análise microestrutural foram utilizadas, tais como difração de raios X e microscopia eletrônica de varredura com EDS acoplado. Observou-se a formação de uma camada não protetora de óxidos de ferro (Fe2O3, Fe3O4 e FeO) e posterior formação de uma camada protetora mais espessa de crômia (Cr2O3). Mais internamente observou-se a formação de SiO2.

Oct 30, 2017

By Gilvandro Bueno

Atualmente, diferentes tipos de vedações laterais de rolos, usados para limitar o efeito de borda em prensas de rolos “High Pressure Grinding Rolls (HPGR)” se encontram disponíveis. O presente trabalho comparou dois métodos usados na vedação lateral: as placas laterais (cheek plates) e as flanges, essas últimas colocadas em um dos dois rolos, a partir de simulações usando o Método dos Elementos Discretos &quot;Discrete Element Method (DEM)&quot;, com acoplamento dinâmico multicorpos (Multibody dynamics ou MBD). Como resultado das simulações foram obtidos os perfis de força compressiva ao longo do rolo, assim como a proporção do fluxo mássico de alimentação que é projetado fora da zona de compressão durante a prensagem. As simulações mostraram que ...do HPGR usando o DEM + MBD se apresentam como uma ferramenta muito útil para visualizar o melhor modelo de vedação de modo a minimizar o efeito de borda durante o processo de prensagem.

Oct 30, 2017

By Ygor Amadeo Sartori Regados

Um modelo para prever a formação da macrossegregação em ligas metálicas binárias foi proposto e implantado a partir das equações macroscópicas de conservação de massa e espécies químicas, resolvidas numericamente em forma adimensionalizada através do Método dos Volumes Finitos para a realização de uma análise paramétrica, na qual se verificou o efeito de parâmetros de processo como o gradiente e a velocidade de solidificação, além de parâmetros do material como o coeficiente de partição de soluto. A análise paramétrica indicou condições nas quais a macrossegregação induzida pela macrodifusão se torna considerável, convergindo para sistemas com interface plana, enquanto altas velocidades de solidificação tornam esse efeito desprezível, aproximando o sistema do perfil de solidificação de Scheil para a fração de sólido. O efeito da reação eutética também foi avaliado, indicando sua influência na formação da segregação de soluto e na estabilidade da interface sólido-líquido planar.

Aug 16, 2017

By Severino Albani Junior

A crise econômica mundial de 2008 obrigou as empresas a se recriarem para atender um mercado mais cauteloso e conservador. Isso demandou uma reformulação na maneira de executar as atividades e estruturar os preços dos produtos. Nesse contexto a ArcelorMittal Tubarão iniciou os trabalhos na área de gestão de ativos focada em manutenção, desenvolvendo um programa para melhoria da confiabilidade dos equipamentos. Dentro desse programa, foi identificada a oportunidade de revisar os planos de manutenção da planta. Essa revisão contempla ajustes no cadastro, criticidade dos equipamentos e revisão dos planos de manutenção no Sistema da Manutenção da Planta. Esse trabalho abordará a metodologia adotada para realização dessas revisões, considerando a formação das equipes de trabalho centralizadas, sua interação com as áreas de manutenção das unidades produtivas, critérios utilizados para revisão dos cadastros/criticidades, a utilização da Manutenção Centrada em Confiabilidade (MCC) para revisão dos planos de manutenção e resultados obtidos.

Aug 16, 2017

By Fernanda Moreno Rodrigues

A adição de elementos microligantes para o controle do crescimento do grão austenítico vem sendo largamente utilizada nas últimas décadas. O Nióbio é tido como o elemento mais importante deste grupo, pois produz precipitados finos na matriz que ancoram os contornos de grão, retardando o seu crescimento. O presente trabalho avalia o efeito do Nióbio no tamanho do grão austenítico do aço VEX, um aço ferramenta para trabalho a quente utilizado para extrusão de alumínio. O estudo baseou-se na comparação entre duas composições químicas, uma sem Nióbio e outra com microadição de 0,02%. Ambas foram caracterizadas microestruturalmente e quanto à tenacidade. O tamanho de grão foi avaliado após austenitização entre 980°C e 1.200°C. Os resultados mostram que a adição de Nióbio é efetiva no refino de grão em elevadas temperaturas, o que é relevante para a aplicação industrial do aço em questão.

Aug 7, 2018

By Camila Peres Massola

Este trabalho avaliou o efeito da corrosão no desgaste de bolas de aço e de ferro fundido branco de alto cromo durante a moagem de minério de ferro, através de ensaios eletroquímicos e de desgaste em moinho de laboratório. Foi feita uma alteração no modo tradicional de realização do ensaio de polarização potenciodinâmica, utilizando polpa de minério de ferro a 70% de sólidos (em peso) no eletrólito. As curvas de polarização obtidas foram compatíveis com os resultados de desgaste, de modo que as curvas correspondentes aos metais na condição mais ativa estavam associadas às menores taxas de desgaste nos ensaios de moagem em laboratório, demonstrando que os ensaios de polarização realizados podem ser utilizados como indicativo do comportamento do metal na moagem de minério de ferro. Verificou-se que, nas condições avaliadas, o efeito da corrosão não foi significativo no desgaste dos corpos moedores, tanto de aço quanto de FFBAC.

Aug 16, 2017

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019