Search Documents

By V. J. Sopuck, O. P. Lavin, Ian Nichol

"A major challenge of contemporary exploration geochemistry is the development of procedures that can locate blind mineralization or mineralization that sub-crops below a cover of transported overburden, the composition of which bears no relation to the underlying mineralization. Over the past few years, the possible existence of diagnostic geochemical features in the country rock associated with volcanogenic massive sulphide deposits has attracted increasing attention both on the local mine scale and on the regional scale. In the present investigation, the nature of the geochemistry of a number of Archean greenstone belts of the Canadian Shield is examined to determine the feasibility of distinguishing productive from non-productive areas of copper-zinc mineralization. The results indicate that productive areas are distinguishable from non-productive areas providing consideration is given to the effects of igneous differentiation on rock compositionIntroductionArchean massive sulphide deposits are an important source of copper and zinc, and to a lesser extent silver and gold, particularly in Canada. As in the case of most other forms of mineralization, there is a continual need to develop new techniques that will improve the chances of success in the search for these deposits. The majority of Archean areas in the northern latitudes are overlain by a variable cover of glacial overburden. Considerable progress has been made in the development of new geochemical exploration techniques for use in glaciated terrain, based on the detection of anomalous dispersion in the glacial overburden. In certain situations, however, as in the search for blind deposits or in areas covered by glaciolacustrine deposits, overburden geochemistry offers little hope for success. In the case of massive sulphide deposits, one possible solution may lie in the detection of anomalous geochemical signatures in the bedrock. Recognizing this possibility, attention has been directed to the investigation of the nature of lithogeochemical dispersion associated with massive sulphide deposits on both regional and local scales, to establish the potential of lithogeochemistry as an aid in the search for these deposits."

Jan 1, 1980

By A. M. Keenan, R. H. Carpenter

Geologic faults have always been a plague to the mining industry, and have often reduced a mining venture from a profitable to a marginal operation, and even at times have forced companies to liquidation or bankruptcy. The use of geology as an economic tool in coal mining is not generally recognized, particularly in coal deposits which are horizontal or essentially flat-lying, in which faulting might not be prevalent. However in pitching coal seams, the existence of faults is considered an inherent challenge, as the inclination of the seam or seams per se, is a product of geologic disturbance. The problems of faults are a constant challenge to the management of the Thompson Creek Coal and Coke Corp. in their operations in Pitkin County, Colorado, where high grade medium volatile coking coal is mined. The background for this paper has been provided by the experiences of these operations, in overcoming the effects of faults in mining, and resolving the fault structures. The properties of the Thompson Creek Coal and Coke Corp. are located in central Colorado, 13 miles southwest of Carbondale, Colorado, a tow] on the main highway between Glenwood Springs and Aspen, Fig. 1. The elevation at the mine portals is approximately 8000 feet: there is a relief of some 2.000 feet to the adjacent ridges rising away from the [nine portals. 'The entire present production of these properties totaling 180.000 tons of clean coal per year is trucked to the railhead at Carbondale, Colorado, from whence it is shipped to the Geneva Steel Plant at Provo, Utah. The properties were initially opened in September 1952. A total of 125 men are currently employed with the production conting from the Number 1 and 3 Mines, and development workings of the Number 2 and 5 Mines respectively. While the No. 2 Vine was opened in 1953 prior to No, 3 Mine, the encountering of faults without sufficient development work accomplished to sustain production, necessitated the diversion of manpower to the other [nines for economic considerations. GEOLOGY '1-he productive coal seams occur in the Mesaverde formation of Late Cretaceous age which outcrop along the eastern edge of the Piance Creek Basin from the Grand Hogback, a part of the southwestern flank of the White River Uplift north of Glenwood Springs, southward through the 'Thompson Creek area and the

Jan 1, 1961

By E. Douglas, V. M. Malhotra

"This report presents the results of a laboratory study undertaken to evaluate ground granulated blast-furnace slag from Algoma Steel Corporation, as a replacement for Portland cement in cemented mine backfill. The evaluation was based on the results of compressive strength tests performed on cylinders cast from mixtures made with a granulated blast-furnace slag and tailings from four different mines in the Sudbury basin. Various percent¬ages of slags and various binder to tailings ratios were used.Tests results show that, in terms of compressive strength, the slag performs as well or better than Portland cement as the binding agent in cemented mine backfill. Lime was found to be a poten¬tially good activator for ground granulated slag in mine backfill applications.A field test was conducted at one of the mines, consisting of placing a mixture of 95.5% ground granulated slag and 0.5% lime into a stope, and inspecting the floor slab as it hardened. The slag performed as expected, considering the backfill mixture proportions used and the preparation of the test site."

Jan 1, 1989

By K. Whysner

The recycling of metal resources in mining influenced water (MIW) requires a paradigm shift from within the mine water treatment industry. The potential to recover zinc for beneficial use in the micronutrient fertilizer industry was investigated through a survey of zinc micronutrient fertilizer representatives. An application of the findings to a case study of the Argo Tunnel influent MIW was then implemented. It was concluded that the potential to beneficially reuse MIW residuals in fertilizers exists; the current process sequences of treatment will need to be modified if metal recycling is to be prioritized.

Feb 27, 2013

By P. K. Sahoo, C. R. Ray, S. S. Rao

Good operation of Soderberg electrodes is dependent upon high quality electrode paste coupled with better electrode management procedures. Without having a good electrode operation, it is not possible to obtain the best outcome from the furnace. In other words that is a good way to say how important the proper electrode operation is. Good electrode performance depends on the slipping rate and current levels, which decides the shape of the baking curve at the level of just below the contact clamps. Negative curvature of baking zone in the central part is considered dangerous because shrinkage takes place outwardly creating abnormal stresses in the electrode. Soft breakages occur when the baking zone comes below the clamps and the casing cannot take the current. This paper deals with various factors affecting baking characteristics leading to soft breakages and also presents case studies in a closed 48MVA furnace with smelting for charge chrome. In case studies in a closed furnace, it has happened that the energy for baking at the low current operation before breakage has been lower than the actual slipping has demanded. At low current there should not be problem, but a problem can occur when the current for some period is raised above the current carrying capacity of the casing. So data for electrode operation in actual period was studied and presented in this paper.

Jan 1, 2007

By Peter J. Clarke

The petroleum industry continued to be the most important mineral activity in Bahrain during 1978-79. Revenues generated by the petroleum sector increased from $378 million' in 1977 to an estimated $419 million in 1978 and approximately $522.5 million in 1979, despite decreasing production over the 2 year period. There were two oilfields that produced revenues for Bahrain, the Awali oilfield, the nation's only onshore producer, and the Abu Sa'fah oilfield, located in the Persian Gulf, north of Bahrain, The Await oilfield has been decreasing output from a high of 27,973,000 barrels in 1970 to 19,000,000 barrels in 1979. Bahrain shared the revenues from the Abu Sa'fah oilfield with Saudi Arabia, as settlement of an ownership dispute. For the first time, in 1978, revenues from the Abu Sa'fah oilfield represented over 50% of the total receipts from the petroleum sector. The years 1978-79 saw the gradual takeover of the Bahrain Petroleum Co. (Bapco), formerly a subsidiary of the California Texas Petroleum Co. (Caltex), by the Government-owned Bahrain National Oil Co. (Banoco). By yearend 1978, Banoco owned 60% of Bapco, and Caltex the remaining 40%. The Government-owned company controlled exploration concessions, managed domestic marketing of petroleum products, and controlled natural gas production and marketing. On December 15, 1979, the Bahrain Government completed full takeover of the Bapco operations. Bapco will continue to own and operate the 250,000-barrel-per-day oil refinery located near Sitrah, as well as handle foreign marketing of petroleum products.

Jan 1, 1981

By A. M. Richardson

The significance of a massive sandstone unit in the immediate roof to longwall support weighting is well known. If the unit lies in the main roof above the zone of caving, its influence becomes more difficult to calculate using traditional methods. Much of the reserves at Cyprus Plateau's new, multi-seam Willow Creek Mine are located in the A Seam. The massive Kenilworth Sandstone is typically situated 21.3 m (70 ft) above the A Seam in the main roof and is on average 14.6-m (48-ft) thick, ranging to 29.0-m (95-ft) thick. This paper describes the application of distinct-element modeling to determination of the appropriate yield capacity for supports at Willow Creek. The modeling was determined to be useful for understanding support loading mechanisms and as an aid to engineering judgment in selecting supports.

Jan 1, 1996

By S. A. Aye

Vibration levels on a variety of equipment in a South African opencast mine were measured in this study. The well-established ISO 2631-1 (1997) standard methodology was used for the computation of weighted root mean square (WRMS) and vibration dose value (VDV). This method was used to evaluate the whole-body vibration (WBV) on a wide range of equipment in the opencast mine using the two main parameters, namely the daily exposure A(8) which is based on the WRMS concept and the VDV which measures shocks. The results obtained show that while the majority of the equipment rendered exposure levels that are below the exposure limit value (ELV), exposure levels on about half of the equipment do exceed the exposure action levels. The study also highlights the importance of shock in the observed responses.

Jan 1, 2011

By W. T. Wertman

A research program to aid development of better and more efficient methods for producing petroleum and increasing its ultimate recovery from underground formations is an integral part of the work of the Bureau of Mines on conservation of the Nation's natural resources. Economic, efficient production of recoverable oil and gas from a reservoir depends to a great extent upon the best and most accurate information that can be obtained from a study of the reservoir rock and its fluid contents. Information on oil and water saturation is pertinent and essential in wildcat, extension, and pool wells for good reservoir operations and prediction of performance. This report presents results of an investigation by the Bureau of Mines of core recovery and degree of drilling-fluid contamination occurring during cable-tool coring operations using oil-base mud. Representative core samples were obtained from 6 major oil-producing sands in 8 fields of West Virginia, Pennsylvania, and New York. Field-mixed, oil-base drilling mud was used for the first coring test, and lightweight, premixed oil-base mud, with an organic chloride tracer added, was used in coring eight other wells. Tracer analyses were made to determine contamination of core by drilling-fluid filtrate. Core analyses, including oil and water content and minimum interstitial water-saturation tests, were made on selected core samples to compare and evaluate water saturations determined by the two methods.

Jan 1, 1958

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

By Paul M. Ambrose

Overall the domestic abrasives industry had one of its best years in 1965. Production and value of all commodities increased over that of 1964 which also was a good year. Production of tripoli that was down in the previous year rebounded and production from two new mines was reported. Plant capacities for production of silicon carbide and fused crude aluminum oxide and production from plants in the United States and Canada increased, but demand was high and yearend stocks were less than at the end of 1964. Foreign Trade.-Increases in value of most imports of abrasive materials in 1965 were offset by a decrease in the value of imported industrial diamond. Production of fused aluminum oxide and silicon car-bide in the United States and Canada and imports of these commodities into the United States increased, but combined exports of finished grain of these materials was virtually unchanged from the previous year.

Jan 1, 1966

By Ronald M. Lewis

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 00 to 90° for FeKa and from 25° to 180° for FeKa1. The wavelengths used for Fe in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): FeKa1 1.93597 A.; Feka2 1.93991 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn. X-ray diffraction crystallography using tubes with iron targets revealed a need for a handy reference for the quadratic functions of iron radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By B Leisemann, M Watkinson

Coal augering is an ideal method for recovering coal from the highwalls of open cut coalmines. Coal augering is a simple process whereby additional flights are added to the auger cutting head and auger holes are drilled at 1.9 m diameter up to 200 metres deep. Traditional monitoring was located at the mouth of the hole and if methane was encountered above two per cent, inert gas was delivered into the mouth of the hole to deplete the oxygen content at the auger cutting head below 12 per cent. The auger operator was asked the question ‘how do you know that this is the case?’ Trials were undertaken to prove that the oxygen content at the cutting head did drop below 12 per cent (the lowest limit for methane to ignite, also known as the oxygen nose point). Initial trials showed that the oxygen content in the mouth of the hole did not drop below 12 per cent and modifications were made to hold the inert gases in the mouth of the hole so that the auger flights could take this inert gas into the hole. In-hole monitoring, after completion of mining and after extracting the auger flights, showed that the atmosphere quickly returned to fresh air. In-hole monitoring was also tried during the augering process and yielded valuable results. This paper will discuss the results of the monitoring, information on the gas results obtained and the methodologies used to optimise the oxygen content at the auger face.CITATION:Watkinson, M and Leisemann, B, 2017. Inertisation of coal augering holes, in Proceedings Australian Mine Vent Conference 2017, pp 293–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By R Zhou, B J. Monaghan, S J Chew, R J. Longbottom, D J. Pinson, H Li, P Zulli, G Zhang, L Lu

Steelmakers are increasingly motivated to use iron ore resources with a wider range of grades and mineral types that were previously considered unsuitable or uneconomical for sintering. In this respect, specific issues, which now require further investigation and understanding, include the sintering of ore types with:- overall higher gangue content- elements that cause problems in the steel manufacturing operations- distinctive sintering performance compared with traditional hematite-rich iron ores. Laboratory-based investigations of the sintering performance and the behaviour of gangue impurities during sintering is an important step towards the successful utilisation of these resources in steelmaking.In terms of laboratory-based sintering investigations, there are two generally accepted experimental scales utilised prior to undertaking industrial-scale trials, which include: bench-scale tablet (compact) testing and pilot-scale pot testing. The former has the advantages of flexibility and more precise control of sintering conditions; but it is difficult to simulate the heterogeneity of a sinter bed. The latter, which is carried out in pots with diameters between 150–500 mm, simulate the commercial sintering process and conditions quite well, but is time-consuming and labour-intensive due to operational complexity. It is therefore desirable to establish a smaller scale pot testing facility that avoids the disadvantages of the normal sintering pot but can provide comparable information.To explore the feasibility of small-scale pot testing, a ‘millipot’ facility was established to examine the sintering performance of iron ores and other non-traditional ferrous materials. The millipot has a diameter of 53 mm and height of 400 mm. The facility has the capability to monitor the sintering temperature at a number of locations (axial, radial) within the sinter bed and to adjust the suction (‘windbox’) pressure. This paper describes the development of the millipot facility and operational procedures, together with initial tests undertaken in order to match its performance with industrial sintering performance.CITATION:Li, H, Zhou, R, Pinson, D J, Zulli, P, Lu, L, Longbottom, R J, Chew, S J, Monaghan, B J and Zhang, G, 2017. A millipot set-up for sintering investigation of iron ores, in Proceedings Iron Ore 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M. Kwasniewski, M. Takahashi

Prismatic samples of a medium-grained sandstone from Slask Colliery (Upper Silesian Coal Basin, Poland) were tested under uniaxial compression, conventional triaxial compression and true triaxial compression conditions. The conventional triaxial compression tests were carried out at confining pressure (p) equal to 12.5, 25.0 and 37.5 MPa. In the true triaxial compression tests the minimum principal stress (s3) was equal to 25.0 MPa and the intermediate principal stress (s2) was 1.5, 2 and 2.5 times higher than s3. Results of the studies show that confining pressure strongly inhibited dilatant behavior of rock samples tested under conventional triaxial compression conditions; the increasing confinement resulted in the growing compaction of the rock material. The effect of dilatancy was also highly suppressed by the intermediate principal stress. While important dilatant, negative volumetric strain corresponded to the peak differential stress at low intermediate principal stress conditions, at high intermediate stresses the rock material was damaged to much lesser extent. As a result, faulting of rock samples in the post-peak region was much more violent and was accompanied by a strong acoustic effect. Les échantillons parallélépipédiques du grès à grains moyens de la mine ‘Slask’ (Bassin Houiller de Haute Silésie, Pologne) ont subi les essais de compression monoaxiale (compression simple), de compression triaxiale conventionnelle (compression triaxale de révolution) et de compression triaxiale vraie. Les essais de la compression triaxiale conventionnelle ont été effectués à la pression de confinement de 12,5, 25,0 et 37,5 MPa. Dans les essais de compression triaxiale vraie la contrainte principale minimale (s3) était de 25,0 MPa et la contrainte principale intermédiaire (s2) était 1,5, 2 et 2,5 fois supérieure de s3. Il résulte des essais que la pression de confinement inhibe fortement le processus de dilatance dans les échantillons testés dans les conditions de compression triaxiale conventionnelle; l’augmentation de la pression provoquait l’augmentation du compactage du matériau rocheux. Le phénomène de dilatance était également limité de façon significative par la contrainte principale intermédiaire. Alors que l’importante déformation volumique négative correspondait à la contrainte différentielle ultime avec les faibles contraintes principales intermédiaires, dans les conditions de fortes contraintes intermédiaires, le matériau rocheux subissait l'endommagement de façon beaucoup moins importante. En résultat, la rupture des échantillons rocheux au stade post-maximum était beaucoup plus violente et accompagnée d’un fort effet acoustique. Prismatische Probekörper des mittelkörnigen Sandsteines aus dem Bergwerk ‘Slask’ (das Oberschlesische Kohlengebiet, Polen) wurden unter der einaxialen Druckbeanspruchung, konventionellen dreiaxialen Druckbeanspruchung und der echten dreiaxialen Druckbeanspruchung geprüft. Konventionelle dreiaxiale Druckversuche wurden bei dem Manteldruck von 12,5 25,0 und 37,5 MPa durchgeführt. Bei den echten dreiaxialen Druckversuchen betrug die kleinste Hauptspannung (s3) 25,0 MPa und mittlere Hauptspannung (s2) war 1,5-, 2- und 2,5-mal höher als s3. Aus den durchgeführten Versuchen ergibt sich, dass der Manteldruck die Dilatanzentwicklung bei den Probekörpern unter der konventionellen dreiaxialen Druckbeanspruchung stark bremst; die Erhöhung des Druckes rief die ansteigende Kompaktion des Gesteinsmaterials hervor. Die Dilatanz wurde auch durch die mittlere Hauptspannung beschränkt. Während die wesentlichen volumetrischen, dilatanten Verformungen der Grenzdifferenzspannung bei den niedrigen mittleren Hauptspannungen entsprachen, bei den hohen mittleren Hauptspannungen wurde das Gesteinsmaterial viel weniger beschädigt. Im Ergebnis war der Scherbruch der Gesteinsproben im Post-Peak-Bereich viel heftiger und mit kräftigen akustischen Effekten verbunden.

Jan 1, 2003

By IPMI Educational and Scientific Foundation

It is with great pleasure that we announce the availability of this fourth issue of the IPMI Journal, a publication of the International Precious Metals Educational and Scientific Foundation. This digital peer reviewed publication has been created as a vehicle for the sharing of technical information related to the science and technology of precious metals. Since 1976, the International Precious Metals Institute has championed the exchange of information of critical importance to the precious metals scientific and commercial communities through its various communications vehicles. This has included instructional videos, annual conference symposia, special topic committee meetings, regional seminars, and professional and student achievement awards. Due to the breadth of important topics related to all aspects of precious metals, it has been the vision of the IPMI to provide a publication available to the general public that would become a key source of pertinent topics containing high quality publications by experts in their fields of study. Historically, the IPMI has attracted world renowned experts in many fields (including Nobel Laureates Henry Taube, Ei-ishi Negishi, Robert Grubs, Professor Ben Feringa, and David MacMillan) in the dissemination of discoveries, inventions, and industry proven practices. Such information has a total value greater than the sum of its parts as seemingly unrelated innovations from distinct focus areas can be adapted to solve problems. Because of this important characteristic of information exchange, we have decided to create a digital journal, available to the general public, that will not only communicate state of the art discoveries and sound practices, but will also review historical communications from the IPMI’s archives that have value and use even in today’s environment. On behalf of the members and leaders of the IPMI, we hope you will find value in this new publication.

Dec 1, 2022

By Rosaire Emond

Le concept du forage horizontal a été développé voilà de nombreuses années. Différents types de plate-formes permettant le forage horizontal depuis une cheminée ont été conçus par divers manufacturiers ou opérateurs miniers. Entre autres, on connaît bien la griffe de montage Alimak à laquelle peut être fixée une plat-forme sur laquelle est montée une foreuse. En 1992, Ross-Finlay a développé sa propre plate-forme de forage qui à notre opinion améliore la flexibilité du concept du forage horizontal, en augmente la productivité et en diminue le coût d?ensemble tout en assurant une sécurité accrue des travailleurs. Tel que montré à la figure 1, la plate-forme employée à la Mine Kiena est composée d?un toit de protection contre les chutes d?objets et de deux passerelles de forage de forme carrée. Le toit et les passerelles sont fixées à une structure de 6.5 m de longueur équipée de deux assemblages de rouleaux (non montrés à la figure) permettant de faire glisser l?ensemble sur des rails Alimak. L?angle du toit et des passerelles peut être ajusté pour des cheminées dont le pendage varie de 65 degrés à 85 degrés.

Oct 1, 2001

In responding to why some longwall roadway development rates are different among mines, the Roadway Development Task Group (RDTG) of Australian Coal Association Research Program (ACARP) has initiated a benchmarking study to survey each longwall mine to determine the correlation between roadway development practices and roadway development performances. This paper describes a web-based relational database system which has been developed purposely to monitor the performance of Australian longwall roadway developments aimed at assessing both the physical and operational factors which could influence roadway development practices and their performance indicators. Statistical analysis of an earlier survey suggested that continuous miner units that achieved more than 1750 m were units mining two-heading development.

Dec 6, 2010

By Mathew Avery, Colby Barrett

In November 2016, a 7.8-magnitude earthquake caused more than 100,000 cubic meters of rock and debris to tumble down and bury the transportation infrastructure below Ohau Point in New Zealand. All routes between the northern and southern portions of South Island were severed. To undertake the rebuilding efforts, the New Zealand government established North Canterbury Transport Infrastructure Recovery (NCTIR) – an alliance to repair the road and rail networks between Picton and Christchurch. NCTIR’s aim was to have the road open by Christmas 2017, but work also continued into 2018 to complete a number of safety improvements along the highway. The presentation will review the initial remediation attempts, the necessity to re-evaluate the original efforts, the need to incorporate techniques that were “outside-the-box” and different from traditional methods, and the logistics and planning that were required to complete the work safely. INTRODUCTION Shortly after midnight on Monday 14th November, a magnitude 7.8 earthquake struck the small South Island settlement of Waiau in North Canterbury, 100km north of Christchurch. The quake was the largest in New Zealand since the magnitude 7.8 Dusky Sound earthquake in 2009 (GNS 2016). While shaking was widespread with over 15,000 recorded ‘felt reports,’ the worst shaking occurred about 50 seconds after the quake rupturing started. The energy of the tremor progressed north over several minutes with surface rupture recorded on a total of 21 faults. The length of all the fault ruptures combined was close to 100km (GNS 2016). The degree of ground shaking was high, recorded as Modified Mercalli Intensity Scale (MMI) Level 8 – Severe. This level of shaking causes considerable damage in ordinary buildings with partial collapse including fall of chimneys, factory stacks, columns, monuments, walls, etc. At a human level, people experience difficulty standing; while furniture and appliances shift. Geologically, the damage depends on the geological setting. In Kaikoura and the surrounding area, especially the coastal highway State Highway 1, north and south of the town, many of the slopes consist of over steepened weathered, fractured greywacke. During the quake, the shaking caused significant and widespread damage with a total of 26 major slips (and many smaller slips); closing both State Highway 1 and the Main North Rail Line between Picton and Christchurch.

Jan 1, 2018

By J. B. Cheatham, M. D. Biggs

This paper presents a systematic method for determining the forces on a simplified roller bit. The kinematics of an actual roller bit drilling in rock is complex; nevertheless, it is desirable to obtain an accurate analytical model.. As a preliminary study, the roller bit is represented here by a simple two-dimensional bit and the rock by a Coulomb plastic material. Results from previous work, plus additional assumptions, are incorporated into a computer program to determine the forces required to move the bit in a specified manner. Example problems are worked by use of this program. By studying similar drilling problems and by supporting laboratory work, one could eventually obtain an accurate analytical model for drilling by an actual roller bit. This could lead to the compilation of a catalog of results that, in turn, would allow selection of the optimum drill bit for any given situation. INTRODUCTION

Jan 1, 1970