Search Documents

By Brad Simser

The Brunswick No. 12 Mine is a 10 000 tonne per day producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400m and 1200m below surface. The combination of a high overall extraction ratio and high horizontal stresses (twice the vertical) has elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning. Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues towards mining in deeper, higher stress environments (e.g. South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically.

May 1, 2003

By Nathan Feldstein

The wetting of coal dust by aqueous solutions of surface active agents (surfactants) has been studied. Selected for study were thirty coals and typical surfactants selected from the typical classes of anionic, non ionic and cationics. Of these three classes the practical use of cationics in aqueous solutions has been eliminated due to the inherent negative Zeta potential charge of the representative coals studied. The wetting of the coals has been examined by column flow, contact angle, and settling rate measurements. Results indicated that both anionic and nonionic surfactants are to be considered viable for use; low critical micelle concentration values are also preferred for the surfactants. Study of native waters showed substantial variation in properties, i.e., pH, calcium ion concentration, and conductance. pH variations were also noted to affect the effectiveness of selected surfactants. Combinations of nonionic and anionic surfactants have, in certain instances, produced synergistic enhancement in the coal wetting superior to the effectiveness of each surfactant alone.

Jan 1, 1981

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy, H. S. Ray

The Ni oxide was reduced with a CO-CO2-N2 gas mixture and the effects were observed of process variables such as roasting temperature, time and CO partial pressure. Extraction of over 90% of Ni was achieved by ammoniacal leaching of ore that had been reduced for 1 h at 760 degrees C under a gas mixture with a volumetric CO/(CO+CO2) ratio of 0.57. The kinetic data were found to conform to the Ginstling-Brounstein equation. The applicability of this model was confirmed by evaluating the apparent activation energy with the use of independently constructed differential and integral plots, which showed an excellent match

Dec 1, 1995

By D. Janicijevic

This paper describes the process of scraper winch pull force measurement and shows the results of the actual winch pull force in extreme stall situations as well as during the face and gulley cleaning. It was found that by slowing down the motor and causing it to slip, torque up to 3.5 times higher than the nominal can be developed, resulting in the same increase of winch pull force. On the other hand, measurements of the actual force needed for cleaning of the face and the gully have shown that the currently used winches are too powerful. The extra torque that can be developed by the already too powerful winch motor poses a significant danger and necessitates the implementation of measures that will eliminate this risk.

Jan 1, 2008

By V. A. Marple

At the Twin Cities "lining Research Center (TCMRC) a project is underway to determine how varying the parameters of a coal-cutting process would affect the amount and the size distribution of the generated dust. The cutting parameters being investigated are the cutting speed, depth of cut and shape of the cutting, tool. To accomplish this research ft is necessary to collect and transport the coal dust venerated at the cutting tool to measuring instruments for analysis. The purpose of this contract was to develop and deliver a system of instruments for measuring the size distributions of the generated coal dust. The instruments employed are essentially those developed for particulate air pollution measurements (1, 2). The instrument system covers a particle size range of 0.005 to 20 microns and is capable of performing in situ measurement and presenting data in real time.

Jan 1, 1974

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

By A. M. Krzanowski, T. S. Golosinski

"This paper presents results of a study undertaken to determinethe feasibility of mining plains overburdens with bucket wheel excavators. Based on extensive geotechnical testing of overburdens under study, the relations between material geotechnical properties and its cuttability were defined. The properties with the highest correlations to the cuttability werethen used to develop the material diggability classification. This classification may be used for identification of overburdens and coals mineable by bucket wheel excavators.IntroductionLow cost of mining and high productivity can be achieved when mining unconsolidated soils and soft rocks with bucket wheel excavators. As a result this mining equipment will likely be introduced into plains coal mines. At present there are plans to use a bucketwheel excavator (BWE) in at least one mine by the end of this decade. Unfortunately, the performance of a BWE deteriorates rapidly with the increasing strength of mined material. To avoid costly misapplication, material diggability must be defined in advance of an application (i.e. the force required at the cutting edges of BWE buckets must be quantified). Correct definition of material diggability permits reliable selection of a BWE, or may indicate unsuitability of this equipment for a particular application.The reported studyu i was undertaken to investigate the diggability of typical prairie overburdens and thus provide a guidance for likely future applications of bucketwheel equipment. Investigations concentrated on the parts of overburden most likely to create problems for a BWE mining. These are defined in Table 1. At present, thin layers of the two investigated materials (samples K and L) are mined by a BWE in an oil sand mine, after being loosened by blasting."

Jan 1, 1987

By B. Xu

Keywords: Magnetic damping, g-jitter, Hot-film anemometry Results from an experimental study on natural convection induced by temperature gradient in molten gallium contained inside a rectangular container. The damping effect of the convective flow from an externally applied static magnetic field is investigated. Induced velocity and temperature fields are mapped using a standard constant temperature hot-film anemometry and a thermocouple with and without the applied magnetic field, respectively. Detailed experimental setup and procedure are depicted in the present paper. Obtained velocity and temperature profiles are examined against previous numerical simulations and reasonably good agreement has been achieved. Obvious damping effect can be observed in both the temperature and the velocity profiles when the external magnetic field presents.

Jan 1, 2005

By H. L. Riley

At the Southern Experiment Station, Tuscaloosa, Ala., reports are prepared from time to time on results of washability studies of coal from important beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. The principal objective of a washability study is to obtain technically and commercially important data to aid in determining the best methods for preparing and utilizing the Nation's reserves, particularly of coking coals. Such information is also important from the standpoint of conservation, because it facilitates the selection of preparation methods that will yield an acceptable product with a minimum loss of coal to the rejects.

Jan 1, 1958

By J Canterford

There is an apparent push to develop and commercialise "new and innovative" process flow sheets. A not-too-difficult reality check clearly demonstrates that the success rate of this push is not particularly significant and in fact could be regarded as a waste or misappropriation of R&D funding and the associated brain power. As Julian Sumner Miller would comment "why is this so?" To put it bluntly, many of the so-called innovative developments are equivalent to gold plating the dunny door - visually interesting but of very limited practical value. This presentation encapsulates some personal lessons learnt over the past 45 years.CITATION:Canterford, J, 2013. Developing a ænew and innovativeÆ process flow sheet - Traps for all players of all ages, in Proceedings MetPlant 2013 , pp 1-5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By J. Nakayama

For drilling large diameter holes for deep foundations, the common and distressing difficulty of long standing has been in coping with ground containing rocky formations and boulders. Where geological formation contains weathered rock or boulders, or deep rock socket is specified, drilling equipment occasionally is found to be unable to drill through and therefore will need supplementary equipment and procedures. Incentive of the MACH Drill Development has been to realize a capable drilling system for rocks of weathered to fresh rock without losing its applicability to usual overburden. Through seven decades' experience of manufacturing and operation of boring machines, the best features of all sorts of drillhead are known such as the drag bit, wing bit, auger bit, diamond bit, rock roller bit, down-the-hole hammer bit, etc.

Jan 1, 1988

Anglo Platinum commenced commercial underground borehole radar (BHR) surveys during 2006 following a series of trial surveys using both the ?slimline? Geomole and Aardwolf systems. Current borehole radar systems comprise radio frequency transmitter ? receiver antennae operating at 30 -100MHz that measure the time taken for a transmitted pulse to traverse a rock volume and be received (Fig 1). The time taken can be converted to distance if the transmission speed of the pulse through the rock volume is known. The transmitted pulse may be reflected off a suitably orientated geological reflector (in reflection mode) or may be recorded in receivers located in other boreholes (cross-hole tomographic mode). In the Bushveld Complex lithologies, these radar systems have ranges of 30-50 metres in reflection mode depending on the electrical properties of local stratigraphic units. Both the Merensky Reef (MR) and the underlying UG2 have been shown to act as reflectors, which offer the opportunity of using BHR as an imaging or mapping tool. Reflection of the radar signal occurs wherever a strong contrast in dielectric constants occurs such as between norite and harzburgite or where chromitite stringers are present. [ ] Fig 1 Main elements of a borehole radar system Much experience has been gained in the practical application of BHR surveys in platinum mining. The value of a BHR survey is that it provides a continuous line of information to ?connect the dots? rather than a few discrete pierce points. BHR surveys can be used to mitigate risk in three crucial areas: ? Mine planning at the strategic as well as tactical level ? geotechnical evaluation of proposed shaft sites, detailed profiling or mapping of reef and disruptions of the reef such as faults, rolls and potholes; ? Mineral resource classification ? identification of structural discontinuities in orebodies affecting resource classification e.g. potholes and reef facies; ? Safety ? identifying areas with poor ground conditions that are often associated with faults, dykes and potholes.

Jan 1, 2007

Wildcat strikes in the Appalachian coal fields, primarily in West Virginia, have resulted in an estimated 4.5 million ton loss in coal production during July and through the first week in August. Since then, the strike intensified further, and on August 9, nearly all of West Virginia's 60,000 miners were off the job with another 10,000 miners on strike in eastern Kentucky. The Bureau of Mines estimates that West Virginia's coal output is currently (8/9) eight million tons below last year when the state produced 108 million tons. West Virginia, the Nation's second largest coal producer of coal behind Kentucky, has not failed to mine over 100 million tons a year since 1938. At the end of the second week in August, nearly all coal miners in West Virginia remained out. The strike is a protest against a cutback in union health and retirement benefits. An announcement June 23 about the United Mine Worker's health and retirement fund precipitated the strike, Fund directors said that because of inflation and production losses caused by earlier wildcat strikes and the severe winter, miners would have to pay the first $250 of hospital costs and 40 percent of doctor bills, up to $500 a year. Previously, the funds paid all hospital and doctor bills. According to the West Virginia Coal Association each day of the strike in West Virginia results in a loss of coal production of 500,000 tons, a loss of $3.8 million in miners wages and $1 million in contributions to the UMWA's health and retirement fund.

Jan 1, 1977

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By Raymond Philippe

Background ?Hatch Water has worked with most major mining companies in Chile on water supply and optimization projects ?Many(copper) mining projects are located in Northern Chile, which hosts the driest desert on earth Water supply options in Northern Chile ?River ?Availability/Rights ?Well(Brackish) Water ?Availability/Rights ?Municipal Wastewater ?Water rights ?Volume ?(Desalinated) Seawater ?Infinite source ?Cost depends on distance and altitude ?Recycling/Reutilization ?Water losses All these options present water quality issues

May 1, 2009

The Bureau of Mines has reviewed those portions of the "Tariff Schedules of the United States Annotated 1963" that are of interest to the minerals industry. This study shows to what extent rates of duty were altered (increased or decreased), and provides a bridge where possible from the old Schedule A classification sys tem to the new TSUS system of statistical reporting of import data. In general the new tariff has corrected previous classification defects and inconsistencies, but the rates of duties have not been materially changed.

Jan 1, 1965

By R. T. Jones

DC arc furnaces are widely used for steel scrap melting as well as for reductive smelting of ore fines. Industrial smelting applications include the smelting of chromite to produce ferrochromium, the smelting of ilmenite to produce titania slag and pig iron, and the recovery of cobalt from nonferrous smelter slags. A number of myths and misconceptions are widely held, especially regarding: the age of the technology, the use of a hollow electrode, arc stability and shape, arc and bath radiation, interaction between the arc and molten slag, electrical behaviour of arcs and slags, a comparison between AC and DC furnaces, DC reactors, the lifespan of bottom electrodes, and the applicability of DC arc furnaces to various metallurgical systems.

Jan 1, 2011

By R. D. Saltsman

This report is in fulfillment of Contract No. H023001.5 awarded to Bituminous Coal Research, Inc., on November 15, 1972. The scope of the work under this contract was to perform a two-phase survey for the purpose of determining the status of work in the following specific areas of industry needs under the Technology Transfer Program and to increase industry's awareness of research efforts under the Federal Coal Mine Health and Safety Act of 1969 6f (P.L. 91-173): 1. Research and development of respirable dust sampling instruments which will more accurately collect the respirable Cuss as defined by the Federal Coal Mine Health and Safety Act of 1969. 2. Development of a better means of control of respirable dust and float dust.

Jan 1, 1973

By George H. K. Schenck

In this decade of the 1.970's it is forecast that eight billion cubic yards of rock will be excavated from 400, 000 miles of new tunnels, drifts and other underground workings in the western world, according to estimates in a report of the Organization for Economic Cooperation and Development (OECD). It is expected that the cost of this work will be in excess of $54 billion in constant 1970 dollars. Most of this underground excavation will be in mining -- 97% of the tunnel length and 89% of the volume - -the balance in construction. In addition to this huge excavating task, in the 18 developed nations of OECD, will be projects in the Communist Bloc and in the developing nations. Underground excavation requires the successful completion of three principle activities: A. Break -- to free rock from the solid work face. B. Remove-- to clear the work area of broken rock. C. Support -- to assure stability of rock surrounding the underground excavation and to eliminate risk of rock collapse. In today's fully mechanized excavation systems, continuous miners, roadheaders or tunnel borers, (A) break the rock loose from the face, and (B) remove broken rock with their mucking devices and load it onto belt conveyors, mine cars, trucks, or any other appropriate haulage system for disposal. Such operations contrast to the more complex, intermittent systems employed when

Jan 1, 1974

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.