Search Documents

By M. Rebolledo, N. Mora, G. Zarate

For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Jetti Resources has developed a novel hydrometallurgical alternative to extract metals of value from mineral ores that the mining industry has struggled to process. Jetti’s catalytic technology, whilst being especially advantaged for extracting copper from low-grade and highly refractory minerals, such as chalcopyrite, seamlessly integrates with existing heap leaching methods and downstream processing operations. The technology uses a catalyst which weakens the metal-sulfide bond in the crystalline structure of the chalcopyrite mineral and alters the structure of the passivation layer allowing the leaching process to continue. Metallurgical test work was conducted to examine the effect of ore variability, in terms of grade and copper deportment. The results presented in this study highlight the amenability of the technology and demonstrate that it is possible to enhance leaching performance of copper primary sulfides over a wide range of copper grades, from 0.1 to 2.2%. Further, it is concluded that despite the copper grade, the tests with increasing chalcopyrite content render copper recoveries up to 4 times higher compared to the tests under non-catalyzed conditions. Jetti’s catalytic technology is currently being evaluated at larger scales, namely a commercial dump leach operation and 50-tonne crib tests. The results obtained thus far are compared to the results from conventional sulfide heap leaching tests. INTRODUCTION For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Chalcopyrite (CuFeS2) is the most abundant and recalcitrant of the copper sulfides (Singer, 2017). Owing to its abundance and economic importance, it is the most demandable natural source for copper worldwide. In fact, the projected demand for copper is further expected to rise much higher beyond the current demand by the year 2020 (Panda et al., 2015). Therefore, it becomes imperative to find low intensity hydrometallurgical technologies for the extraction of copper from chalcopyrite in ores of such low-grades that are un-economic to concentrate and to augment the supply by extracting copper from ores with complex mineralogy that cannot be concentrated (Watling, 2013).

Jan 1, 2019

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011

Mr. BRADFORD said :-On assuming this chair, which has been occupied by so many gentlemen of conspicuous ability; my first words must be an expression of the gratitude I feel for the honour you have done me in electing me to be your President for this year.When considering the subject matter of this address to you to-night, quite frankly may it be stated that for a long time I was on the horns of a very great dilemma, for while I could discourse on the modern political trend in relation to our industries at great length, it appeared to me that this was not the place for such a discussion. Next I turned to a consideration of whether a discourse on the theory and practice of iron and steel would be of interest.I, however, banished this idea also from my mind, because it appeared to me that you have already had a surfeit of this on your visits of inspection to our local industries and I did not want in any way to be held responsible for the iron entering into your souls! I therefore propose, with your kind consideration, to address you on other subjects of common and vital interest to all.My first words and thoughts turn on the absolute necessity of eliminating waste in our methods. If we are to succeed in our...

Jan 1, 1926

By Jiann-Yang Hwang

Microwave heating has been proved an effective method to rapidly heat iron oxide. This offers an opportunity to apply microwave heating in the steelmaking process. The reduction reaction of iron oxide is traditionally achieved at high temperature with reducing gases such as H2 and CO generated from various sources, including coke, coal, and natural gas. This study investigates the differences in iron oxide reduction using conventional and microwave heating under H2 and CO atmospheres. A special microwave thermal gravimetric device was designed and built to facilitate the investigation. With this device, iron oxides can be heated by electric resistance heating, microwave heating, or a combination of methods. The incoming CO and/or H2 also can be preheated to simulate a potential utilization of recovered heat. The iron oxide weight and temperature can be monitored during an entire reduction period. A series of reduction experiments have been conducted. The results are presented and discussed.

Jan 1, 2006

A large lab apparatus was designed using a scale-down methodology based on the design legacy of the current FLSmidth commercial forced air flotation machines. This new apparatus, along with a new test methodology, was used to evaluate new rapid prototype concepts. The apparatus was designed to monitor bubble size, power, pumping capacity, Jg, velocity profiles, froth character, and tip speed. The methodology developed follows a sequence that goes from hydrodynamic tests and solids suspension tests to a flotation kinetic test. This methodology has been demonstrated to be a good tool to determine the effect of machine design changes on flotation.

Jan 1, 2012

By J. J. Taber

Gas and water permeabilities of a large number of samples from the Pittsburgh and Pocahontas coals were measured at various overburden and mean flow pressures. A wide variation in the air and water permeabilities was obtained for each type of coal. Overburden pressure has the most significant effect on the single-phase permeability. Considerable hysteretic effect was observed for both air and water permeabilities. Gas permeabilities are affected to a lesser degree by mean flow pressures above atmospheric. However, at subatmospheric mean pressures, appreciable increase in permeability occurs for low permeability samples. Air and water relative permeabilities were also measured for numerous samples of Pittsburgh and Pocahontas coals. Tests were performed under steady-state conditions for both drainage and imbibition cycles. Results indicate that the flow of gas is greatly reduced during the latter process, whereas it is largely undiminished over a wide water-saturation range during drainage. It is also shown that imbibition saturation distributions obtained from liquid-water imbibition as opposed to water-vapor adsorption produce gas permeability curves of radically different character. The effective permeabilities to both gas and water were significantly reduced with the application of overburden pressures in the range of 0 to 1,000 psig, but the general shapes of the relative permeability curves remained the same.

Jan 1, 1974

By Mark S. Sanders

Six underground coal mine shuttle cars (three high seam and three low seam) were used to assess visibility using the concept of visual attention locations (VALs) and an improved human eye reference measurement instrument (HERMI Mark II). Each machine was assessed in the inby and outby direction of travel with no canopy and with the canopy in its highest, and lowest position. In addition, the illumination level at each VAL was determined. Results showed that the most important variable determining visibility was operator eye position. When this variable is controlled, the addition of a canopy has no effect on visibility. Further, with eye position controlled, there is no difference in visibility between high and low seam machines. The visibility and illumination assessments found blind spots in the operator's field of view located on the opposite side of the car from the operator and ahead of the machine. Suggestions for reducing the blind spots were made. The report also included a procedure manual for using HERMI and the system of VALs to assess visibility from underground shuttle cars, continuous miners, and scoops.

Jan 1, 1983

By P. H. S. W. Kulatilake, B. Malama

To simulate brittle rocks, a mixture of glastone, sand and water was used as a model material. Thin galvanized sheets were used to create joints in blocks made out of the model material. To investigate the failure modes and strength, both the intact material blocks as well as jointed model material blocks of size 35.6 × 17.8 × 2.5 cm having different joint geometry configurations were subjected to uniaxial and biaxial compressive loadings. Results obtained from the intact model material blocks are used to validate a new intact rock failure criterion for biaxial loading. Results obtained from both the intact and jointed model material blocks are used to develop a strongly non-linear new rock mass failure criterion for biaxial loading. In this failure criterion, the fracture tensor component is used to incorporate the directional effect of fracture geometry system on jointed block strength. The failure criterion shows the important role the intermediate principal stress plays on rock mass strength. Zur Simulation spröder Gesteinsarten wurde ein Modellmaterial aus Dentalgips, Sand und Wasser hergestellt. Daraus wurden Blöcke gegossen, in denen mittels dünnen, galvanisierten Blechen Trennflächen erzeugt wurden. Die Blöcke mit Abmessungen von 35.6 × 17.8 × 2.5 cm wurden in einaxialen und biaxialen Druckversuchen belastet. Es wurde das Versagensverhalten und die Festigkeit von intakten Blöcken sowie durchtrennten Blöcken mit unterschiedlicher Trennflächengeometrie untersucht. Aus den Ergebnissen der Versuche an intaktem Material wurde ein neues Versagenskriterium für biaxiale Belastungen validiert. Die Ergebnisse der Versuche an intakten und durchtrennten Blöcken wurden verwendet, um ein neues stark nicht-lineares Versagenskriterium für geklüftetes Gebirge unter biaxialer Belastung abzuleiten. Darin wird der Bruchtensor verwendet, um den Einfluss der Trennflächengeometrie auf die Festigkeit zu erfassen. Das Versagenskriterium stellt heraus, welche Bedeutung die mittlere Hauptspannung für die Gebirgsfestigkeit hat. Un mélange de platre dentaire, de sable et d’eau a été utilisé pour développer un matériau analogue des roches fragiles. De fines feuilles galvanisées permettent de créer des discontinuités représentatives des discontinuités naturelles dans des bloques fabriqués avec ce matériau analogue. Les modes de rupture et la résistance, tant pour le matériau intact que pour le matériau avec ses discontinuités, ont été étudiés sur des blocs de 35.6 × 17.8 × 2.5 cm soumis à des efforts de compression uniaxiaux et biaxiaux. Différentes configurations de géométrie de discontinuités ont été considérées. Les résultats obtenus à partir des blocs intacts permettent de vérifier un nouveau critère de rupture pour les roches intactes soumises à des efforts biaxiaux. Les résultats obtenus, tant avec les blocs intacts qu’avec les blocs avec discontinuités, sont utilisés pour développer un nouveau critère de rupture, fortement non linéaire, pour les massifs rocheux soumis à des chargements biaxiaux. Dans ce critère de rupture, un tenseur de fractures est introduit pour caractériser les effets directionnels de la géométrie des systèmes de discontinuité sur la résistance des blocs avec discontinuités. Ce critère de rupture démontre le rôle important de la contrainte principale intermédiaire sur la résistance des massifs rocheux.

Jan 1, 2003

FROM time to time articles have appeared in the technical press on the interesting subject of surface combustion. The theoretical part of the problem has, for practical purposes, received ample consideration in those articles, but the number of practical applications of surface combustion referred to has generally been very small.It is the writer's object to review some recent developments in surface combustion, and also to try to arrive at an estimate of its advantages and possibilities. It is not necessary for this purpose to dilate upon the phenomenon of surface combustion itself. Many interesting things have been said on the subject by Pro£. W. A. Bone, of Leeds, to whose researches the recent developments are largely due. A few illustrations may make clear what is meant by surface combustion.Prof. Bone, in an experiment, took a platinum crucible, which he heated in the flame of a Meker-burner. Then he turned the gas off for a second, and, opening the stop-cock again, allowed the combustible mixture to impinge upon the crucible, thetemperature of which was still well below the ignition temperature of the gas. Although no flame was visible at this stage, it was soon clear that, nevertheless, the gas and air had continued to combine, as the crucible would attain a red heat after a few seconds.Another instance of surface combustion was shown by a Mr. Fletcher, in 1882. He placed an iron ball, weighing 3 lb., on a slab of fireclay, heated it for a few seconds with a blow-pipe, and blew the flame out, leaving the gas-mixture still...

Jan 1, 1915

Several industrial-scale HydroFloat separators have recently been installed at Mosaic?s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The benefits, theory of operation and commissioning of the equipment are also discussed.

Jan 1, 2007

By Mike Cammack, Logan Huppert, Gustavo Azpilcueta

During the summer of 2015, Unisea Inc. sought proposals for the G1 Dock Replacement Project in Dutch Harbor, Alaska. It would be a one year project and construction was scheduled to begin in the spring of 2016. One aspect of the project was the requirement for a layer of armor stone to protect part of the dock. An estimated 30,500 tonnes (37,670 t) of armor stone were needed for the project. The source of rock was the Unisea Quarry due to its proximity to the project and the quality of the stone meeting all the required technical standards.

Jan 1, 2018

By W. Sondermann

"AbstractWith the increasing demand in reuse of inner city areas and the urgent need for deeper foundation pits under cramped circumstances, adjacent structures close to and high ground water level, the well-known established technologies especially with small to mid-sized dimensions are often too time consuming and occasionally not economic to install lateral support systems. The alternatives for these specific cases could be the usage of the deep mixing technology to create lateral support systems in reinforcing the deep mixing elements additionally to transfer the horizontal loads from earth – and water-pressure.With increasing demand in depth and water tightness, verticality and overlapping of single column solutions are becoming the key in execution. In addition, for some applications subsoil-conditions were not ideal for wet deep mixing technologies. The tubular soil mixing system (TSM) as a combination of mechanical mixing and support of hydraulic cutting by jet grouting can provide solutions toovercome these challenges.1. Current market conditions and trendsThe present financial crisis and the efforts not only to consolidate national budgets, but also to rescue certain banks, have not left the building industry unaffected either. Some drastic cutbacks to public budgets, along with the increasingly restrictive granting of credit for the financing of construction projects, have led to enormous over-capacities in the building sector, with purely negative impact. As a consequence of these negative developments, many companies are experiencing the pressure to restructure more quickly and to reduce costs but at the same time to keep the consequences of all activities, both externally and internally, within limits acceptable to employees, owners and finance institutions and last but not least consumers."

Jan 1, 2014

By R. Biss

"Niobium or columbium, as usually called in North America is becoming a more and more important metal in the industrial world because of its attractive properties.Eventhough discovered in the early nineteenth century, it was not until the 1930's that its use became more widespread. The discovery of large commercial deposits in the late 1950's and the demand of industry for steel with high strength and toughness further promoted its use. To assure its adequate supply new or-e processinr technologies had to be developed. So, beside the traditional gravity concentration, the flotation process was employed for the partial upgrading of pyrochlore concentrate at S8ve (Norway) plant in 1953. The flotation process was equally used at St-Lawrence Columbium plant in the province of Quebec, Canada. The new plants at Araxa and Catalao in Brazil and at St-Honore, Canada, which supply almost of all niobium used today in the non-Communist world, also adopted the flotation process. The processes using long chain aliphatic rnonoarnines, diamines or sulfonates as collectors proved to be difficult especially on weathered types of ores or on those having a substantial content of silicate gangue minerals. They almost completely failed in case of alkaline intrusive rocks as syenites, nepheline syenite, ijolites and pyroxenites, composed almost entirely of silicate minerals. A lot of effort was devoted all around the world on research of new, more efficient flotation processes. So in 1982, Les Services T.M.G. Inc. (Niobec), sole producer of pyrochlore concentrate in North America, developed the direct pyrochlore flotation process from carbonatites. In 1983, at about the same time, the Quebec Department of Natural Resources Laboratories and Les Services T.M.G. Inc. announced a successful recovery of niobium Minera1s from a low grade nenheline syenite ore."

Jan 1, 1984

By T. T. Chen

The behavior of gold in a conventional copper electrorefinery anode slimes treatment process is expounded on in this study. In the raw anode slimes generated in a copper electrorefinery, gold occurs mainly as tiny particles of metallic gold, which are commonly attached to selenide particles. Some gold is also present in selenide form. Decopperizing the anode slimes retains much of the metallic gold, but also promotes the incorporation of gold in the structure of silver-rich selenide species. A greater fraction of the gold is converted to (Ag,Au)2Se or Ag3AuSe2 when high-Se and high-Ag anode slimes are decopperized at elevated temperatures and pressures. After pelletization and roasting of the slimes, the gold is converted to a (Ag,Au)-alloy and Ag3AuSe2. Smelting of the roaster products eliminates the selenium and converts the gold to a silver-rich (Ag,Au,Pd)-alloy in the dore metal. In the subsequent silver electrorefining process, gold collects as a gold-rich (Au,Ag,Pd)-alloy in the gold mud. Dore smelting rejects many impurities as a silica slag; minor amounts of gold are present as a (Ag,Au,Pd)-alloy in the silica slag. This gold is recovered by flotation and is recycled to the dore furnace. Gold is identified in both the tellurium caustic leach residue and the parting plant wash water mud as tiny particles of metallic gold. These products are also recycled to the dore furnace to recover their gold values.

Jan 1, 2008

The term geochemistry - chcmbtry' of the earth - is almost limitless in its implied subject, but of recent years a major trend of research in this field has been towards economic application in the search for mineral deposits, and in particular for those of some ofthe less common elements for which a demand now exists.Geochemistry is in a state of slow transition from a purely descriptive subject to a fundamental science concerned with the relationships that exist between the distribution of the elements in the earth's crust and the physical characteristics of the atoms of those elements. The progress achieved promises a set of basic principles which will relate the atomic characteristics of an element to the physico-chemical conditions that make for its dispersion or concentration. This means that, given a geological map of an areasufficiently detailed for the physico-chemical conditions existing in past geological eras to be deduced, there is the possibility that the relative distribution throughout that area of any element present, and its likely mode of occurrence, could be predicted from a consideration of its atomic characteristics.Since the atomic characteristics of the elements are becoming increasingly well defined by physical research, the attainment of this ideal of prediction depends upon:(a) the strengthening of geochemical theory; and(b) the development of petrological and mineralogical methods of assessing the conditions of temperature and pressure prevailing in geological formations at various stages in their history.The other prime requirement is a d.etailed geological map - a requirement that is all too often lacking.The fact that there has been very little "geochemical approach" to problems of economic geology in Australia should not be taken to mean that there is little point in trying to develop such an approach here in as active and as rigidly scientific a manner as possible. The degree of success that has attended the attempts so far made, to which reference is made below, suggests the reverse, particularly in view of the relatively slight cost involved if the investigations were properly organised on a centralised basis. There are three aspects of geochemistry that are directly applicable to the search for economic minerals.(a) The classic technique of the prospector can be made more sensitive and reliable by the use of modern equipment coupled with the application of geochemical theory to geological and structural data. The case of the rare alkali elements (see below) is givenhere as an illustration of the way in which the distribution of elements can be predicted from the first principles of geochemistry, thereby replacing the prospector's dependence on his "sixth sense" that enabled him to suggest that a certain area of formation was"favourable" for the occurrence of a certain type of mineral deposit.At its best, this sixth sense amounted to an almost subconscious correlation of all relevant associations and typical occurrences of the particular mineral experienced by the prospector during his...

Jan 1, 1950

By L. W. Bahney

MANY methods for the determination of gold or silver, or both, in cyanide solutions have been published, which with care in manipulation, and modification in some cases, will give results that are satisfactory. It is possible to classify or group these methods as follows: 1. Evaporating the solution in a porcelain or agate-ware dish containing litharge,1 or in a "boat" made of lead foil. 2. Forming a lead sponge containing the precious metals by means of zinc shavings,2 zinc dust,3 or a piece of aluminum.4 3. Decomposing the cyanide solution with an acid and precipitating the precious metals by the use of one or a combination of some of the following: Copper sulphate,5 sodium sulphite,6 hydrogen sulphide,7 cement copper.8 4. Precipitating the silver by zinc dust held in a Hooch crucible and determination with a standard solution of sulphocyanate.9 5. Electrolysis.10 6. Colorimetry.11

Jan 2, 1915

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

THIS has been a much-neglected branch of engineering. With the majority of industries labour is the chief item of trouble and expense. Anything that will reduce trouble and increase efficiency is well worth considering. It is only of recent years that any attempt has been made on a scientific basis to improve conditions sporadic attempts having been made from time to time, privately and by law. Some have been successful, others unsuccessful not necessarily the fault of those who initiated the ideas, though naturally mistakes were made in some cases for want of experience, but those whom it was desired to benefit were not always prepared for the change, and by their distrust hampered schemes instead of assisting them.Man power is generally more expensive than machinery, though there are exceptions, such as when a small amount of work has to be done in a place where machinery does not exist, and it would not pay to instal any or where labour is cheap, and skilled workmen are scarce as in some tropical countries. When machinery is first introduced it generally causes the suspicion that it will deprive men of their work. It may cause men to vary the conditions of their work, and in some individual cases, when men are unable to conform to changed circumstances it may result in a certain amount of hardship; but, after all, the less competent must not hold back progress for the general good. Besides, changes as a rule do not take place suddenly, so old hands can generally find work at their particular calling 'till nature requires them to retire. In cases where men take to machinery, they not only find that they are relieved of the...

Jan 1, 1918

The Ekati Diamond Mine is located on permafrost terrain in CanadaÆs Northwest Territories. The mine rock consists of: diamond-bearing and barren kimberlite; and surrounding waste rock such as granite. The kimberlite occurs in several vertical æpipesÆ that are, or will be, mined using open pits. Early predictions of drainage chemistry at Ekati identified the potential for ARD due to sulfide oxidation from both waste rock and kimberlite. This was surprising for the kimberlite, because neutralisation potentials (NP) are typically hundreds of kg CaCO3 equivalent/t. However, subsequent testwork showed that substantial portions of the NP ædisappearedÆ quickly, apparently due to the unusual non-carbonate mineralogy. In any case, additional predictive work concluded much of the rock was benign and there would be no ARD. Shortly after mining started, ARD appeared from both the waste rock and kimberlite, although a few years passed before the company and its consultants recognised that at least some of the acidic water was ARD. Numerous other processes have been put forward as possible explanations for the remaining acidic drainage, although none have been either confirmed or eliminated. Because: the causes of the ARD and acidity are not known; no causes have been eliminated and more have been added; drainage chemistry was not predicted accurately; and future mining will encounter similar rock. I believe the Ekati Diamond Mine needs high-level assistance to understand current chemistry and to avoid problems with future drainage. Organisations like INAP, MEND3, and universities could provide this assistance.

Jan 1, 2003

By Joseph A. Vanous

The inductive communication system was developed under this contract for use in the hoist of deep mines. This program was a four phase program with experimental dual frequency equipment resulting from Phase I, emergency single frequency equipment developed under Phase II, and equipment documentation required under Phase III. An additional emergency system was provided under Phase IV.

Jan 1, 1976