Search Documents

By Stanley Griff, William Herrera, William O. Seals

"The Navy initiated liquid propellant research in the early 1940's. The first promising Navy liquid propellant, Otto Fuel II, was developd in the early 1950 as a potential torpedo fuel. Later, the Navy developed a HAN based liquid propellant designated NOS-365, a hydroxylammonium nitrate, isopropylammonium nitrate and water formulation. A large gas volume generated by this propellant produced a large wake behind the torpedo. As one can readily understand, this negated the useof the propellant for this application. Recognizing the large gas volume as a desirable propulsion system for guns, the Navy embarked upon a gun propellant proqam. Utilizing a bulk loaded gun sysytem, the program failed when the gun was destroyed by the propellant detonating."

Jan 1, 1990

By Wouter Hartman

Xuandong Coal Mine is mining coal in one of the most challenging underground environments in the world. This work has found that it is not only challenging but it also has the composition for some interesting rock mechanics and ground control conditions. The paper highlights the extreme mining and rock mass behavior conditions encountered when mining coal at 900 m below surface. It was found that the ground control environment associated with geological weakness, low coal material strength and stiffness, was reasonably well controlled; however, the chain pillar geometry and design did not take these geological weaknesses into consideration. Some of the chain pillars employed were quite large, which resulted in floor punching and secondary floor heave, which causes extreme difficulty for production. No barrier pillar has been employed except for the center 164-m-wide main headings pillar with a w/h ratio in excess of 40. After assessing the location and geometry of a 200-m-thick dolerite sill overlaying the coal measures, we found the probability of it breaking up into to smaller fragments and producing a larger goaf to be low. Therefore, the influence of the dolerite sill on chain pillar loading is considered small compared to the low coal, immediate floor and roof rockmass strength. It is further recognized that horizontal stresses could be locked up within the dolerite sill, which would likely result in regional bending that would be distributed through the chain pillars. This has, to some extent, already occurred, and the effects have been seen and felt through excessive floor heave, pillar punching, and coal bumps (seismicity). We?ve also found that there was a need to employ basic rock mechanics principals in assessing the stability of future multiple seam mining layouts.

Jan 1, 2012

By Giuliana A. Zelada-Tumialan

Reduced workability and flowability of the concrete through the tremie tubes and drilled shaft reinforcement have been identified as the main causes of tremie-concrete drilled shaft concrete defects. This paper discusses two recent case studies of defective tremie-concrete drilled shafts. The defects (soft inclusions, aggregate segregation, and low concrete strength) were primarily caused by the combined effects of the tremie placing sequence, rapid concrete slump loss, and poor passing and blocking characteristics of the approved concrete mix design. The level of detail contained in the drilled shaft specifications varied between projects. However, even when the specifications incorporated several of the more recent recommendations for tremie-concrete placement, the case studies showed that typical provisions for concrete mix proportioning and placement can be further improved to minimize construction defects such as those described in this paper. Based on the findings of the case studies presented, recommendations for the development of more effective specifications are provided. The recommendations include requirements for mock-up testing of proposed concrete mix designs and evaluation of the tremie-concrete placement sequence. Performance of such testing and evaluation would greatly reduce the potential for drilled shaft defects and consequent time and financial burdens associated with them.

Jan 1, 2009

By Victor Erickson

ECONOMIC recovery, which began in 1958, carried through into 1959 but was somewhat retarded by the 116-day steel strike beginning in July 1959. Recovery and economic growth increased production and consumption of mineral fuels 3 percent above 1958. The increase was accomplished despite a drop of 26 percent in coal exports. Prices remained constant during the year so that the value of production and consumption also increased 3 percent over 1958. Stocks in the hands of producers at yearend were little changed from the supply at the beginning of the year. Employment in the field of mineral fuels decreased 6.4 percent from 1958. Average hourly earnings were up 7 percent, and average hours worked were up 5 percent, with the result that weekly earnings gained 11.8 percent. Internal freight rates were relatively constant, but ocean tanker rates declined both in 1958 and 1959 from the high rates charged during the Suez crisis. The index of major input expenses decreased for anthracite, held constant for bituminous coal, and increased for petroleum. The index of labor cost per dollar of product and per ton of product declined again in 1959 to a new low in anthracite and bituminous-coal mining industries.

Jan 1, 1960

Laboratory testwork was carried out on an overall orebody composite, of 2.9 per cent Cu and 4.2 per cent Zn, prepared from drill core taken from the Currawong fine-grained, copper-zinc massive sulphide deposit near Benambra in Victoria. While 90 per cent of the copper was readily recovered in a concentrate of 20 per cent Cu, after grinding to 95 per cent passing 38 microns, zinc responded poorly to conventional flowsheet/reagent regimes. Experience elsewhere with the use of reverse cleaning, to separate pyrite from sphalerite, led to a series of tests in which better (but still modest)metallurgical results were obtained. The best result was a zinc recovery of 55 per cent in a concentrate of 50.5 per cent Zn. The major loss of zinc occurred in the reverse cleaning stage where the unit recovery of zinc was similar to pilot plant results achieved at Mount Isa Mines on similar feedstock. Diagnostic mineralogy suggested that an overall zinc recovery of 70 per cent was probably the practical upper limit, at a 50 per cent Zn grade.

Jan 1, 1999

By O. A. Lima

Effective solids suspension is a necessary precondition for particle collection, and solids suspension is largely dependent on the hydrodynamics of the flotation cell. This study attempted to correlate the status of the suspension of apatite particles of different sizes in a Denver laboratory flotation cell versus the impeller rotational speed (N) adopted to operate the machine. The latter variable (N) influences the impeller capacity to lift the particles from the bottom of the tank and also to disperse them throughout the volume of the vessel. Such an impeller capacity can be characterized by the critical impeller speed for the accomplishment of solids off-bottom suspension (Nz) and also by the velocity of the radial water flow discharged by the impeller (U) divided by the particle terminal settling velocity (Us). This way, the status of the suspension of apatite particles inside the flotation cell can be characterized by one of three categories: ?segregation? (N/N2 < 0.60 and Us/U > 0.08); ?suspension? (0.60 = N/N2 < 1 and 0.06 < Us/U < 0.10); and ?dragging? (N/N2 = 1 and Us/U = 0.03). The range of impeller rotational speed (N), which was able to suspend the finest particles (Dp = 90 µm), was unable to suspend the coarsest particles (Dp = 254 µm). Conversely, the high value of N (N > 1,300 rpm), which is adequate to suspend the coarsest particles, may promote the entrainment of the finest particles to the froth layer.

Jan 1, 2009

By Lee W. Abramson, William H. Hansmire

The H-3 Project is planning, design, and construction of a 10-mile (16 km)-long final segment of new highway that traverses the Koolau mountain range in Oahu. Interstate H-3 traverses North Halawa Valley on one side of the Koolau Mountains and Haiku Valley on the other side. The project includes a tunnel through the mountain range. The one-mile (1.6 km)-long twin-bore Trans-Koolau Tunnel will have two lanes in each direction. The total roadway width including shoulders in each bore will be 38 ft (11.6 m). The geologic and geohydrologic conditions along the alignment present a variety of tunneling problems. Geologic conditions consist of volcanic materials deposited generally in fairly thin basaltic layers. These volcanic materials generally weather down to "MH" soils which are compressible but relatively strong. Perched ground water that is recharged by heavy rainfall is present in the mountains. The paper presents results of initial geologic surveys and exploratory boring, and plans for exploratory tunneling and testing programs. A site specific classification method developed to characterize the weathered profile is presented.

Jan 1, 1989

By Keith Pucalik

Understanding Vibrations fr om Blasting focuses on explaining blast vibrations and their effects on people and homes while keeping an eye on the importance of the use and significance of explosives in our daily lives. Unlike many predecessors, this film will help blasting pro f e s s i o nals explain blast vibrations and address many of the layman’s most fre q u e n t l y asked questions. The film can be used in pubic hearings, given to homeowners during preblast surveys, or played at educational seminars for professionals. The film can also be used after blasting has begun and residents have already experienced vibration events.

Jan 1, 2004

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By M. Hopf

The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However, even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able consistently to identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed).Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa. Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway

Jan 1, 2006

By J Taylor, L Richards, M McKenzie

When a collapse in its services shaft caused rapid gas build up and its premature closure in. 1951, the Blackwater Mine at Wiauta was in full production with significant ore reserves yet to be mined. A total of nearly 23 tonnes of gold was produced from the mine during its 44 year life. It was New ZealandÆs deepest underground mine, producing gold from an extensive sub-vertical mineralised quartz reef that averaged 0.6 m in width. Mining was by stoping between adits and short shafts, latterly with the main mine access through the 840 m deep Prohibition shaft. Macraes Mining Company Ltd are presently investigating the possibility of reopening the mine. This paper outlines a preliminary assessment of the main geotechnical factors for achieving the reopening, using recent exploration and old mine information. The greywacke host rock mass in the vicinity of the quartz reef has been evaluated using both these sources, and the paper discusses how the geological structure, intact and rock mass strengths, the rock mass defects, in situ stresses, and groundwater inflows may effect the reopening and support of the prohibition shaft, the excavation methods and support for a new supplementary shaft, and the likely excavation and support requirements for working adits and stopes in the rejuvenated mine.

Jan 1, 1996

By Cathleen J. Webb, Arden D. Davis

The Homestake Gold Mine at Lead, South Dakota, has been proposed as the host site for the Deep Underground Science and Engineering Laboratory. The laboratory will house neutrino experiments in mine workings at the 7400-foot depth, as well as research in geomicrobiology, rock mechanics, and ground-water flow. Initial plans for the laboratory were developed in 2000 after Homestake Mining Company announced the closing of the underground gold mine. Homestake’s owner, Barrick Gold Corporation, had agreed to donate the mine for a laboratory if it could be protected from environmental liability. That initial agreement was delayed, and Barrick turned off the mine’s pumps in 2003, allowing lower levels of workings to begin to flood with water. In early 2004, the Governor of South Dakota signed an agreement with Barrick that would indemnify the company and eventually transfer ownership of the mine to a state laboratory authority. South Dakota’s governor also announced plans to ask the state legislature for funds to help in the initial construction of the laboratory. A consortium of scientists from several states is currently preparing a detailed laboratory proposal for the National Science Foundation.

Jan 1, 2005

By D. F. Smith

The thermodynamic data presented in the literature for zirconium compounds are incomplete. Among the compounds for which adequate data are Zacking are zirconium fluoride and sulfate. This paper reports experimental heat-content values determined by the Bureau of Mines for these two zirconium salts throughout the temperature range of 273° to 1,200° K. No crystalline transformations were found in the two compounds investigated, and neither of the compounds melted over the temperature range studied. MATERIALS TESTED The Oak Ridge National Laboratories, Oak Ridge, Tenn., supplied the two zirconium salts used in this investigation. The zirconium fluoride was high- purity reactor grade material. The zirconium sulfate contained between 0.01 and 0.10 percent hafnium and calcium, and other elements in concentrations below 0.01 percent, A spectrographic analysis of the two compounds is given in table 1. Before use the compounds were dried at 400° C. for several hours to removed adsorbed moisture.

Jan 1, 1962

By A. McKenzie

During the late 1990s Anglo American PLC was evaluating the Gamsberg zinc deposit in the Northern Cape Province. As the primary South African metallurgical technology provider, Mintek became involved in the evaluation of a pyrometallurgical process for the recovery of zinc from the Gamsberg deposit. eloping DC arc furnace technology for the metallurgical industry. This includes the patented Enviroplas® process for the treatment of zinc bearing waste materials. As a consequence Mintek has developed extensive expertise in the pyrometallurgical processing of zinc bearing materials. However, Mintek?s technologies stopped with the production of Prime Western Grade (PWG) zinc. Early on in the evaluation of the Gamsberg project, it became evident that the refining of PWG zinc would play an important part in the economic viability of the project. At the time the only pyrometallurgical technology available for the refining of PWG zinc to Special High Grade (SHG) zinc was the New Jersey process. This process represents 50-year-old technology and has not undergone significant refinement since the technology was developed. In order to provide a complete pyrometallurgical flow sheet for possible implementation at Gamsberg, Mintek assessed the New Jersey process with a view to either improving the technology or developing a new technology appropriate to the 21 century. In 1998 Mintek convened a consortium consisting of Mintek, the University of Cape Town, Eskom Enterprises, Bateman Metals and Anglo American PLC. The consortium successfully applied to the Innovation Fund for funding to develop a new process for the pyrometallurgical refining of PWG zinc to SHG zinc. The main aims of the project were to develop a new technology for pyrometallurgical zinc refining that conformed to the following: ?Decrease the production cost of SHG zinc metal to stimulate the development of the Gamsberg deposit. ?Be compatible with the current Enviroplas® process, preferably as an add-on to that process. ?Should use electrical energy to benefit from local price tariffs. The project commenced at the beginning of 2000 and consisted of three phases: ?an initial technology search and assessment of the fundamental aspects of zinc distillation. ?the design of a pilot plant for zinc refining. ?the manufacture, commissioning and operation of the pilot plant. A new technology based on a DC arc boiler feeding a packed distillation column was developed and during 2003 the project culminated in the successful operation of a 200 kg/h pilot plant. Ultimately, all of the aims of the project were met and the main outcome is that an advanced process for the pyrometallurgical refining of zinc (the Zincref process) has been developed. The main innovation of the technology was the switch from an energy transfer limited process to a mass transfer limited process (for which a patent has been registered).

Jan 1, 2004

By D. M. Avant, A. J. Solomon, S. M. Pickering, W. R. Fox

Introduction Most high purity silica is produced from crystalline quartz, generally from sand. However, there is a small area of southern Illinois where a porous, friable white chert rock is found that is very different in physical form from quartz sand. This microcrystalline material, commonly referred to as tripoli, is more easily ground to micron sizes than sand. Although of similar Moh&apos;s hardness, microcrystalline tripoli is less abrasive than either ground quartz sand or many synthetic abrasives. Location The southwestern corner of Illinois is underlain by extensive deposits of very porous chert; in some places the material is quite white. Two companies, Illinois Minerals Co. and Tammsco Inc., mine and process this white material. The Illinois Minerals plant is located at Elco, and the Tammsco plant is in Tamms, IL. Both companies mine from various locations within a 10-mile truck haul of their plants. Production from this district has been continuous since at least 1915. Malvern Minerals Co. mines and processes a generally similar microcrystalline, friable novaculite near Hot Springs, AR. Geology The southern Illinois white tripoli area is on the southern flank of the Illinois Basin. The commercial silica zone is a facies of the Clear Creek chert of Lower Devonian Age. To the north, where it occurs deep in the basin, the Clear Creek is a siliceous limestone. In the mining area, thin overburden has allowed access by surface ground water, which has leached away the carbonate content and left a quite pure silica residue. Fossils characteristic of sea bottom deposition, such as brachiopods and trilobites, are occasionally encountered in mining. The structure of the mining area is poorly known, due to infrequent outcrops. Strata in most mines are inclined at dips of 5° to 20°. There appear to be occasional high angle normal and reverse faults, but these are seldom of any significance in mining. The friable white silica zone mined in the Clear Creek chert is overlain by dark brownish-red chert and siliceous shale. Exploration drilling to date has not encountered the base of the microcrystalline tripolitic zone. Chemical content Leaching by ground water solution has removed virtually all the carbonate from the original siliceous limestone. Impurities encountered are red to yellow iron oxides, aluminous clays, and occasional black manganese oxides. The silica has no detectable formula water. A typical chemical analysis and physical properties are listed in Tables 1 and 2. Mineralogy and crystallinity Southern Illinois friable tripoli appears amorphous under the polarizing microscope. No crystal structure and only occasional, vague, patchy anisotropism is evident. However, the material gives an excellent quartz X-ray diffraction pattern. Thus, so far as X-ray mineralogy is concerned, the material is clearly

Jan 12, 1986

Jan 1, 1967

By Jacques J. Eksteen

Metallurgical accounting around toll treatment smelters pose a number of challenges. This paper reviews the requirements for good sampling practice, and how conflicting requirements for good furnace operation and design often makes reliable closure of the metallurgical balance tenuous at best. Typical physical causes of variance and bias will be identified. The propagation of error (in the form of variance) will be discussed for a copper smelter.

Jan 1, 2006

By Axel Doelcken

?? Liebherr excavators in standard configuration are generally designed to operate in an ambient temperature range between -12°C and +55°C (10.4 °F and 131°F). ?? To operate effectively and efficiently in very low temperatures special consideration needs to be given to the design ??An inappropriately designed hydraulic system unable to withstand extreme changes in temperatures or varying working conditions will lead to: - premature wear and more frequent replacement of components - increased maintenance & unplanned downtime This will affect productivity & operating costs.

May 1, 2008

By D. Harrington, G. S. Rice, R. R. Sayers

"The Bureau of Mines in Serial No. 2606,4 issued in May, 1924, gave tentative specifications for rock-dusting to prevent coal-dust explosions in mines. Subsequently, a sectional committee of the American Engineering Standards Committee was appointed to formulate recommendations for standard practice in rock-dusting coal mines. The report of this Committee which follows was approved by the American Engineering Standards Committee, December 30, 1925. Several members of the Bureau of Mines staff served on this Sectional Committee and its recommendations are essentially in harmony with those of the Tentative Specifications in Serial No. 2606.As certain explanatory details contained in that serial are not included in the recommendations formulated by the American Engineering Standards Committee, it should be considered by coal-mine managements in conjunction with the committee's report which follows:Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions 1. Definitions of Terms Used: The term ""Mine"" shall include all underground excavations from which coal is hoisted or transported to the surface, through one or more openings.The term ""Main Haulage"" shall include all underground slopes and planes, all rock tunnels, and all entries excepting those from which rooms or chambers are turned.The term ""Entry"" shall include all underground haulageways, travellingways and airways, excepting working places as defined below:"

Mar 1, 1927

By G. Luttrell

Coal preparation plants play an important role in modern society by providing high quality feeds for coal-fired utilities, industrial boilers and metallurgical coke facilities. Unfortunately, field data indicate that preparation plants are often not operated under optimum conditions, resulting in lower productivity and lost profits. In many cases, this shortcoming can be attributed to a failure by plant operators (i) to recognize the importance of correctly adjusting plant operating conditions to accommodate requirements dictated by coal sales agreements within different coal markets and (ii) to properly account for variations in product moisture with particle size across different plant circuits. This paper discusses the important influence of moisture constraints on preparation plant optimization and provides a case study to illustrate the potential gains that can be realized via proper understanding of plant moisture control.

Jan 1, 2009