Search Documents

By J R. Lang, J K. Mortensen

The Canadian Cordillera contains numerous classic porphyry deposits and several unusual subtypes, including the alkaline suite of porphyry Cu-Au deposits and the Tombstone magmatic suite and associated Au¦W deposits. The alkaline suite formed in collisional settings in island arcs whereas the Tombstone suite was emplaced in an active fold and thrust belt in a continental arc. In addition to different regional settings, these suites differ in the type of underlying basement, metallogeny, and the styles of mineralization. Both magmatic suites were emplaced over short intervals, probably in response to specific tectonic events. In the case of the alkaline suite, the tectonic event promoted magmatic processes suitable for the formation of porphyry Cu-Au deposits. The tectonic environment is less well constrained for the Tombstone suite, but the result was the formation of distinctive porphyry and intrusion-related Au¦W deposits.

Jan 1, 1995

By Birger Schmidt

INTRODUCTION Conceptual design of the first Exploratory Shaft (ES-I) for the Nuclear Waste Repository in Basalt (NWRB) began in July 1981; detailed design began in February 1982, and was largely completed by December (RKE/PB, 1983). The intent was to begin shaft construction by January 1983. The site had been prepared at that time, a construction manager selected and on board, the starter hole excavated and lined, and steel casings were under procurement. Government policy changed, however, and construction was halted before the drill rig started turning. Construction is now planned to begin in 1988. ES-I is a part of the site characterization program for the NWRB. The shaft will be used to develop production data and related information relative to drilling shafts at the site near Richland, WA, and to provide access to the repository horizon for site characterization and testing. The early program called for one shaft and some 330 m (1000 ft) of drifting. The program has since expanded to include a second shaft (ES-II) and more extensive drifting and testing. Currently, both shafts are planned to be 1.8 m (6 ft) in finished diameter, but studies are underway to determine if the second shaft should be larger. The drilling method was selected for shaft construction primarily because it offered a significantly shorter construction period than conventional shaft sinking using freezing and grouting. The finished drilled shaft will be lined with a continuous steel lining. Personnel are safer during construction with a drilled shaft than with a conventionally sunk shaft. The drilling method

Jan 1, 1987

By C. E. M. Meskers

End-of-life Electronic and Electrical Equipment, o_cially called WEEE, is unjustly regarded as mainly a waste management problem. What is structurally overlooked is the enormous resource impact of these devices. EEE rep- resents a tremendous metal resource, which should be uti- lized through e_ective recycling, which has a much lower environmental footprint than primary production. The actual amount of end-of-life EEE recycled today is embar- rassingly low since insu_cient EEE is collected and part of the collected EEE is exported to developing countries, where it is largely not entering o_cial recycling systems. To achieve a global recycling society issues like technol- ogy, economics, life cycle structure, stakeholder aware- ness and legislation have to be addressed in a global, co-operative manner so that sustainable closed product cycles can be obtained. Requirements for a "global re- cycling society" are de_ned to address today's reality of global ows of used consumer products, taking into ac- count the likely needs of the future.

Jan 1, 2009

By Toshiharu Teranishi

When we apply the Au nanoparticle superlattices to the future nanooptical and nanoelectronic devices, the control of not only the particle size but also the interparticle spacing and symmetry of superlattice are the essential problems to be overcome. First, we developed a novel synthetic procedure to precisely control the particle size of alkanethiol-protected Au nanoparticles in the range from 1.5 to 9.7 nm by the heat-treatment of the small Au nanoparticles in the solid state. Absorption and nonlinear optical properties of alkanethiol-protected Au nanoparticle superlattices were then elucidated. On the other hand, the hexagonal close-packed (hcp) 2D superlattices of small Au nanoparticles with the interparticle spacings from 1.9 to 3.6 nm were successfully prepared by using newly-synthesized ligand for single electron tunneling devices. Finally, various symmetric superlattices, such as chain (2-fold), quasi-honeycomb (3-fold), square (4-fold), etc., of Au nanoparticles could be produced by making use of interligand interactions or some templates.

Oct 1, 2003

By Claude Cunningham

Difficulty has always attended the evaluation of rock breaking energy available from explosives, owing to the complexity of the way in which it is released, and the destructive amplitude of the pressures. Many problems have arisen and continue with this difficulty, including the following: I. Formulation of improved compositions to deliver appropriate energy levels to the blasthole walls, or to deliver previous results at improved cost. How appropriate is it to use various ingredients, such as Aluminium, water, salt? 2. Claims over energy issues, resulting in wasted time and expense, over things that sound good in theory but are very difficult to tie down. 3. Purchasers of explosives make decisions based on claimed “Bang per Buck” from different manufacturers, where the estimate of “Bang”comes from simplistic numbers from various, very unequal detonation codes. The above problems are escalating as time progresses. Using the high level IDeX PC 2000 detonation code, we have found a way to portray the differences between formulations in a way which relates to their breaking effect in the field. The basic method is to plot the adiabat from the detonation state to full expansion in units which express the practical implications. Energy alone cannot deliver results, so we use the curve to examine its manifestations: pressure and temperature. Internal energy is plotted with these. The method displaces relative energy numbers, as it portrays the context in which the energy is available. It is used here to compare an ANFO, an emulsion and a doped emulsion, as well as the effect of Aluminium. The effect of the shock pressure regimes and temperature correlate well with what is seen in the field.

Jan 1, 2000

By J. B. Czirr

MESA Corporation has completed a four-year program for the Bureau of Mines to develop a technique for measuring roof competence in underground coal mines. The preferred technique employs a tracer gas that is injected into a roof borehole drilled near the working face. The tracer gas performs the dual purpose of determining the pressure loss rate from the borehole and of marking the diffusion pattern of the the escaping gas. The primary detection technique relies upon observation of the rate of pressure drop in a hole drilled in the roof strata under test. If this measurement indicates a significant probability of roof collapse, the gas diffusion pattern is outlined with the Leak-gun tracer-gas detector. These two techniques provide a comprehensive method for predicting the relative probability of roof collapse in operating coal mines.

Jan 1, 1985

The outlook for suppliers of energy to the expanding economies of the Pacific Basin region is essentially positive, but particularly for exporters of high quality steam coal. This paper argues that economic growth in the Pacific Basin region has exceeded world economic growth for some years and that this will continue to be the case for the next decade at least. It looks briefly at the link between economic growth and energy demand and at the relationship between energy demand and the demand for electricity. Changing preferences in fuel mix for electrical generation in the region are noted and tentative forecasts made about variations in this mix. The pros and cons of various forms of fuel used to generate electricity are considered from the point of view of the consumer. Having concluded that steaming coal in particular is likely to become even more important as a generator of base load electricity, the paper looks at the opportunities this presents for exporters such as Australia, and touches on some factors that could prevent development of those opportunities. This paper will concentrate on electrical energy. For the purposes of this paper, the Pacific Basin refers essentially to Australia, New Zealand and the Asian countries bordering the Western Pacific. As a supplier, Siberia is not included because, although it has great potential, it is thought that problems of climate, infrastructure and political restructuring will delay the realisation of that potential until the next century. Although it deals with the Pacific Basin region, where many countries are industrialising rapidly from a predominantly agricultural base, it looks at the experience of mature industrial DECD economies where their experiences seem relevant.

Jan 1, 1990

By E. A. van Wyk, M. R. de Villiers

"Mining companies strive to increase and maintain production, while simultaneously remaining competitive in the global economy. Furthermore, they must ensure workers’ safety and maintain good safety records. The use of virtual reality (VR) facilitates the development of tools and systems for various purposes that can improve knowledge and understanding of the work environment. VR is a rapidly growing technology that uses the ever-increasing power of computing to simulate real-world and imaginary environments and situations with a high degree of realism and interaction. The availability of 3D modelling tools and simulation programming engines that work effectively with a mid-range desktop PC and standard 3D graphics card, make VR technology viable and attractive for mainstream training applications. The design, development, and implementation of interactive VR training systems is proposed as an innovative approach to augment safety training. However, in order to assess the impact of such VR training systems it is of particular importance to determine the effectiveness of the design of such systems. This article proposes an evaluation framework for this vital purpose. This framework comprises criteria to assess VR training systems, specifically relating to usability, instructional design, VR systems design, and mining industry context-specific aspects. Although the framework was developed as an evaluation tool to assess effectiveness of the design of such systems, it can equally well be used as a set of design principles to inform the design of VR training systems for mining. IntroductionMining in South Africa has been the main driving force behind the history and development of Africa’s richest and most advanced economy (Coka, 2012). The South African mining industry is frequently criticised for its poor safety record and high fatality rate (Stoddard and Skweyiya, 2016). Inadequate or insufficient training is often cited as a root cause of accidents (Van Wyk and De Villiers, 2009; Tichon and Burgess-Limerick, 2011). Virtual reality (VR) is a rapidly growing technology that utilizes the ever-increasing power of computing to simulate real-world and imaginary environments and situations with a high degree of realism and interaction (Webber-Youngman and Van Wyk, 2013). VR is currently being used or investigated as a training solution in a variety of industries. VR technology has developed rapidly and costs have fallen to levels where it can now be considered for mainstream training applications. The availability of 3D modelling tools and simulation programming engines that work effectively with a mid-range desktop PC and a standard 3D graphics card, make VR even more attractive to mine training centres (Van Wyk and De Villiers, 2009)."

May 1, 2019

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012

By J. B. Brodie, C. Pelletier

"The vulnerability of Canadian and U.S. companies, their directors, officers and employees to onerous penalties associated with violations of environmental statutes and common law actions has provided the impetus for the increasing use of environmental audits. This trend is developing in direct proponion to the cost and difficulty of obtaining liability insurance. Companies operating in British Columbia should be cognizant of developing legislative and enforcement trends and their implications for individual and corporate responsibility. Canadian mining companies doing business in the U.S. should be particularly aware of the environmental exposure which may be assumed with property acquisition or by operations which produce or use any of an ever-increasing list of regulated substances.The environmental audit is now a key component of prudent business planning which will identify noncompliances and environmental liabilities, outline defensive strategies, and assist in a legal defence should charges be laid. This paper will discuss the purpose and mechanics of an environmental audit with emphasis on those features which will maximize protection against statutory and common law actions.IntroductionThe environmental audit is but one weapon in a comprehensive defensive strategy for corporate and individual survival in an increasingly litigious world. The principles of the environmental audit have been formulated as a logical response by management to an ever-growing list of environmental vulnerabilities, which often have the potential to result in plant shutdowns, prosecutions or fmancial liability of major proportions. Accordingly, the audit may play a critical role in maintaining profitability as well as assisting in the defence of a company and its employees against actions taken by regulatory agencies and citi7.cns under statute and common law. Should convictions result from these actions, the penalties are likely to be ameliorated by the demonstration of due diligence through management policy supporting the audit procedure.An awareness of environmental sensitivities, strict adherence to licensing requirements, and planning for environmental emergencies are now generally considered to be as important to profitable performance as operating costs, metal prices, and labour peace. Why is this so? The increased priority given to environmental matters is partly a result of changing attitudes amongst the mining profession, but perhaps more importantly, it is also a direct consequence of the proliferation of ever more stringent environmental legislation, the targeting of management for responsibility and the draconian penalties imposed for violations of such legislation. Contributing to this trend are recent court decisions involving disputes of an environmental nature in which the standard of care required for a successful defence now requires almost super-human diligence in environmental management. The principle of ""strict liability"" (in which negligence or permit violation does not have to be shown) is also being increasingly applied in the resolution of civil actions."

Jan 1, 1988

By Frederic Masse

With widespread acceptance in the market place, many engineers are choosing ground improvement techniques to provide suitable foundation subgrade at sites that would have traditionally required deep foundations. This paper discusses the Controlled Modulus Columns (CMC) ground improvement technique and some case histories highlighting the use of this technique for retail development sites. CMC are a sustainable and cost-effective ground improvement technology that transmit load from the foundation to a lower bearing stratum through a composite CMC/soil matrix. The CMC installation is also an attractive option from an environmental perspective because it utilizes reverse flight augers, which displace the soil laterally. This installation technique achieves two goals: it densifies the soil around the CMC, which improves load transfer into the element and avoids spoil and its disposal. Through the introduction of two cases histories, we will present the key benefits of the CMC technology. Each case history will clearly illustrate how a CMC solution can reduce the overall cost of a project when compared to a more traditional type of deep foundations. They will also show how the use of CMCs has benefits that relate to the overall sustainability of the project. While CMCs are an attractive financial and sustainable option, they have also demonstrated that the performance of the system is comparable to that of deep pile foundations. Because CMCs are a relatively new technology many potential users are not aware of its benefits. While we discuss the use of CMCs to support buildings in this paper, CMCs also have been used for a variety of other applications including foundations for tanks, mechanically stabilized earth (MSE) walls, and embankments

Jan 1, 2011

By Fredrick L. Johnson

The Jerry Peak, Jerry Peak West, and Boulder Creep: Wilderness Study Areas contain no identified mineral resources. Two workings, a 20-ft-long adit and a pit, were found in Paleozoic, brecciated, limonitic jasperoid in the east part of the Jerry Peak Wilderness Study Area (WSA), but no significant metallic mineral values were noted. Lenses and pods of quartz containing copper minerals occur in Paleozoic sedimentary rocks 1/2 mi north of the Jerry Peak West WSA. Similar rocks crop out along Pine Creep: in that study area but no copper-bearing quartz lenses were found.

Jan 1, 1984

By M. G. Dellow, D. W. Hendriks

"In early 1988 the decision was made by Noranda Minerals Inc. to install pressure filters at the GECO mill to replace the vacuum disk filters and bunker-C fired rotary kiln dryers. Two filters were installed, one for copper concentrate and one for zinc concentrate. Completion of the project was scheduled for the third quarter of 1989. The filters were made operational in October 1989. Some work remains to be done yet on loadout conveyors for total project completion. Capital expenditures for the project have been approximately $2,700,000 to date. The paper describes the selection criteria for the filter, the installation, startup and associated problems.1. INTRODUCTIONThe filter model chosen for the project was the Verti-Press model VP-50-6(7) (Figures1 ,2 and 3) by Filtra Systems of Farmington Michigan, USA. The decision to purchase the Filtra Systems filter was based on gaining familiarity with a different, mechanically simpler pressure filter than the Larox design and to a lesser extent a necessity for repairs to the the disc filter, rotary kiln dryer system used at the GECO operation for its' copper and zinc concentrates. The fact that it is manufactured in North America was an important consideration. The same basic principles of pressure filtration as the Larox machine are used but the implementation is quite different and somewhat simplified with some interesting innovations. 2 filters were installed to allow direct and immediate comparison of the same machine on both fine and coarse materials. Copper concentrate is reground for cleaning on the flotation circuit while zinc is not. Screen analysis of composited samples of concentrates for 1988 indicated that expected copper concentrate would be approximately 66% minus 400 mesh and zinc 50% minus 400 mesh (Tables 1 & 2).The filter is composed of six horizontal chamber module layered vertically and held together in a frame by 1 O large bolts; torqued down to 4000 ft-lbs. 6 individual belts are used; each with its own drive system. The belts themselves are of a 3 piece design with a filter cloth portion, a support belt and a rubberized intermediate portion. They are held together with steel clipper lacings. A basic description (1) of the filter operation is as follows. ""The horizontal filler chamber is closed by hydraulically pressurizing seals across each end of the filter chamber to 200 psi. The feed pump then pumps slurry into the filter chamber. Suspended solids are retained on the filter belt and the filtered solution drains into a lower drip tray and flows from the filter by gravity. At the end of the filtration or feed cycle, a rubber diaphragm in the filter chamber is pressurized hydraulically to 100 psi pressure. This removes all free liquid from the filter chamber and the filter cake. After the diaphragms are retracted the filter cake is blown with compressed air to remove any residual cake moisture. The seals are then retracted and the belt is advanced to discharge the filter cakes. During the cake discharge the belts are washed with a spray header located at the drive end of the filter. The belt assemblies move one (1) complete revolution during the cake discharge cycle. The cycle automatically repeats until the filter is shut down by the operator."

Jan 1, 1990

By Rodrigo Toro, Ivan Yutronic N

"The Copper Concentrator Plant of Compañía Minera Doña Inés de Collahuasi (CMDIC) is composed of three grinding lines, the third one being the largest. Due to the capacity feature of the third line, specially its SAG mill, it is a priority that the advanced process control team of the Company deploys a supervisory control strategy that allows this unit to operate in an optimal way, in order to achieve the maximum productivity at minimum cost. It is in this kind of tasks where advanced control applications play a key role in obtaining the best economic profit of the process.The advanced process control team, formed by people from Informatics, Automation and Operations of CMDIC have assumed the challenge of generating the transition from a manual SAG Mill 1011 operation (40 x 22 feet, the largest copper SAG mill of the world), to a fully automatic SAG Mill using a multivariable control strategy instead of a rule based on expert control system (widely used in industrial mining process control applications).Therefore, CMDIC decided to work together with Honeywell APC Team implementing an advanced automatic control strategy for the SAG Mill 1011, using for this purpose a technology called Model Based Predictive Control (MPC), based on a variety of control methods that uses dynamical models of the process, obtained from input/output data, in order to print the process knowledge into a group of mathematical relationships that links the constraints (controlled variables) with available commands (manipulated variables) and measured disturbances.The main objective of the advanced control strategy is to ensure process government, tending to throughput stability and optimization, by the execution of coordinated control actions, proactively avoiding measured disturbances effects and the SAG mill overloading.The most important benefits of using a multivariable control strategy are: the automated operation of SAG mill 1011 (that was manually operated before the implementation of this application), a safer, more coordinated and more stable process operation, achieving through this an increase of throughput and a decrease of specific energy consumption, controlling the amount of oversize material production, power consumption, mill loading, noise and torque. In addition to the operational results, this challenge has consolidated a control team, with the participation of engineers and operators, diminishing the typical implementation time and achieving a greater use of the application in a short time."

Jan 1, 2010

By Patrice Favreau, R. F. Ph. D. Professor Emeritus Favreau

After Nobel invented dynamite, blasts were carried out by trial and error, without the use of equations based on the fundamental principles of Chemistry and Physics, although everyone accepted that shock waves were involved; but no equations were available to calculate their intensity. Around 1950 however, M.A. Cook proposed a procedure to calculate the thermochemistry of an explosive, and thus evaluate theenergy released during the explosion of a fully confined explosive. Some blasters then began to use theEnergy Factor; the latter, however, does not subdivide the energy into its three kinds of activities necessaryfor a successful blast, as demonstrated in 1968 by reference 2, namely i) the shock wave which weakensthe rock; ii) the stress field SS which fully fragments the rock; and iii) the release of the stress SS whichcauses the fully fragmented rock to burst out with the velocity necessary to move the rock into the muckpile. The article explains that the way to achieve a successful blast is by insuring that the explosive energy divides properly into the weakening action of the shock wave which is necessary to prevent large collar blocks and toe, and into adequate stress field intensity SS which is necessary to obtain good fragmentation size distribution at the crusher, as well as adequate burst out rock movement to achieve easy mucking.

By John S. Corsentino

This Bureau of Mines study is a listing of fuels -related projects that are presently under construction, planned, or proposed by various companies and organizations in the Western United States. The future facilities covered in this report fall into the following categories: coal mines and expansions to existing mines, electric powerplants and expansions to existing plants, coal conversion plants, waste-to-fuel conversion plants, oil shale projects, tar sands projects, potential geothermal facilities, coal slurry pipelines, railroads related to fuels development, uranium mines and expansions to existing mines, uranium mills and enrichment facilities, oil refineries, and natural gas processing plants. The projects are listed by state. Data concerning the company, location, planned markets, process type, initial operating date, capacity, water requirements, employment, current status, and other relevant information are included. Each project has been plotted on an accompanying state map. Due to present uncertainties concerning the fuels industry, some of the listed projects may never he constructed. No attempt has been made to determine the degree of certainty or viability of each project.

Jan 1, 1976

The Pike River Coal Company is set to develop the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine will be developed to extract a coking coal deposit of the Brunner Seam, some 46 km north-east of Greymouth, using a combination of continuous miners and hydraulic extraction.   The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. As such, the major restriction to planned extraction is protection of:   +        the western escarpment, +        vertical and sub-vertical rock faces, +        permanent water courses, +        significant vegetation, and +        steep slopes.   The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumps down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.

Jan 1, 2005

By F. N. Kissell, C. M. McCulloch, Maurice Deul, J. R. Levine

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas content of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and desorbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By A. C. Wilson

"In 1991, local prospector C. “Mickey” Clement recovered at least three alluvial diamonds from the Michipicoten River. Two of these stones were sent to the Department of Mineralogy, Royal Ontario Museum, where they were identified as industrial-grade diamonds with weights of 1.05 and 1.13 carats. Both stones were described as frosted and graphiteinclusion riddled.In 1995, prospector Sandor Surmacz and geologist Marcelle Hauseux discovered diamonds in bedrock approximately 20 km north of the Michipicoten River. An 18.1 kg bulk sample of a xenolith-rich lamprophyre, taken from an outcrop at the side of the Trans Canada Highway north of Wawa, yielded 1 macro diamond and 5 micro diamonds. All but one was gem quality (Sage, 2000).Since then, more than 36 occurrences of diamonds in bedrock have been reported in an area approximately 30 km2 in size, centred 20 km north of the town of Wawa. The occurrences are hosted within a sequence of unusual, Archean-aged, heterolithic breccias previously considered to have no economic significance. Ten kimberlite occurrences also have been confirmed in the Michipicoten greenstone belt in the last five years. Two of these kimberlites are diamondiferous.To date, expenditures on property acquisition and diamond exploration in the Wawa are estimated at CDN$120 M.This paper summarizes the geological observations made on these occurrences and describes the relationship between the occurrences and the regional geology."

Jan 1, 2004

By Brian W. Stump

Seismic networks provide the primary technology for monitoring compliance with a comprehensive test ban treaty. The design goal of the network is the identification of possible clandestine explosions detonated below the earth’s surface and possible in the oceans. Complementary technologies such as infrasonic, hydroaccoustic and radionucleide (particulates and noble gases) monitoring supplement the seismic monitoring covering explosions in the atmosphere and oceans. Seismic sources that will produce detectable signals will be both natural and man made in origin. Naturally occurring events include earthquakes, many of which are beneath the oceans or deeper than it is possible to drill, and volcanic eruptions. Accurate locations of such events to depths of beyond 10 km precludes consideration of these events further.

Jan 1, 1995