Search Documents

By John F. MacDonald

From 19BS thru the present, Guy F. Atkinson Construction Company has been involved in several transportation construction projects in the Seattle area. Two of these contracts, the Mt. Baker Ridge Tunnel, and The Seattle Bus Tunnel, had unique foundation features. MT. BAKER RIDGE TUNNEL ACCESS PITS The Mt. Baker Ridge Tunnel is part of the general upgrading of the I-90 freeway between I-405 and I-5 (see Fig. 1). It is located on the western shore of Lake Washington and consists of a 1300 foot long large diameter tunnel thru Mt. Baker Ridge. The ridge consists of over consolidated silts and clays overlain by a loose to medium dense silty fine sand. The water table is perched in this upper layer of material. The clays of Seattle have a history of being very sensitive to excavation. The hills are marginally stable and numerous landslides have occurred recently in the area of the tunnel. [ ]

Jan 1, 1990

By Hookings H. J

UNDER a contract relating to the sale of a Broken Hill concentrate, the differentiation between granular and slime concentrate is determined by the proportion of the material which will pass a 200-mesh (I.M.M. standard) screen, and this has led to considerable attention being devoted to the question of laboratory sizing tests with screens of this order.It was found that many of the screens turned out by the makers during the war, and also since its termination, did not conform with the I.M.M. specifications as closely as some supplied in pre-war days. A perfect screen is hardly to be expected, but when the above contract was framed the parties anticipated that, by special care being taken during manufacture, a screen at least as good as the best pre-war screens would be available. This, however, has not proved to be the case, and the large irregularities in screens recently supplied render them useless for sizing determinations under the contract. The makers were approached through the Institution of Mining and Metallurgy, London, with the view of obtaining a few screens conforming as closely as possible to the 200-mesh I.M.M. standard, and in response to a request twelve pieces of screen were...

Jan 1, 1922

Assessment of the Consistency Between Different Laboratory Froth Stability Measurements

Sep 13, 2010

By W. A. McKinney

The segregation process consists of heating crushed oxidized or mixed oxide-sulfide copper are with a copper-volatilizing salt and carbonaceous material at about 750° C. to produce metallic copper which is recovered from the furnace calcines by conventional sulfide flotation. The Bureau of Mines made a number of bench-scale laboratory tests on two copper ores to determine the relative merits of using halogen salts, potassium chlorate, or various salt mixtures as volatilizing agents in segregation of the copper. Laboratory investigation of typical siliceous and calcareous oxidized ores revealed that sodium chloride was a better segregating agent than the other salts. Calcium chloride, magnesium chloride, sodium fluoride, or potassium chlorate gave nearly as good segregation as the sodium chloride on the siliceous ore. Segregation of the calcareous ore with calcium chloride was nearly as good as that obtained with sodium chloride, but inferior segregation resulted when magnesium chloride, sodium bromide, or potassium chlorate was employed. The use of sodium bromide or sodium iodide on the siliceous ore, and of sodium fluoride or sodium iodide on the calcareous are, gave appreciably poorer segregation than sodium chloride or the other salts. Other tests of the ores, using mixtures of sodium chloride and the other halogen salts or potassium chlorate, gave segregation approaching that obtained with sodium chloride.

Jan 1, 1962

By Francis T. Freeland

In the West many precious-metal mines are worked in patches by lessees, under conditions which closely resemble those of what is called " tribute-work" in Cornwall.* The company has its own foreman or inspector, and usually employs the engineman, blacksmith, pumpman, and perhaps other general workmen. As an inducement to work on a new piece of ground, where no ore is in sight, the company may advance a " footage"

Jan 1, 1896

By A. Noble

The design of separation circuits can be a complex, labor-intensive and costly process. While the engineer?s experience along with extensive data sets and simulation are crucial tools for determining the final solution, a more fundamental approach is suitable to compare preliminary options and reduce the number of potential alternatives. In light of this need, the authors have developed the Circuit Analysis Reduction Tool (CART?). This software package relies on the fundamental principles of linear circuit analysis; however, the solution methodology has been streamlined to automatically incorporate stream splitting and unique separation performance for each unit. The resulting tool allows preliminary analysis of circuit designs without the need of detailed feed characterization. In addition to the basic analytical approach, this paper supports the veracity of the methodology with several simulated examples for various separation models.

Feb 27, 2013

By J. D. Steenkamp

"In July of 2016 and June 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA submerged arc furnaces producing ferrochromium in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Subsequent thermodynamic calculations allowed for the quantification of the potential for chemical reaction between refractory and slag or alloy contributing to wear in the tap-hole area. Results from both wear profiling and thermodynamic calculations are reported here. IntroductionFerrochrome (FeCr) is an essential alloy in the production of stainless steel (Gasik, 2013). In 2017, 11.7 Mt of FeCr was produced (Pariser et al., 2018.). The main producers were China (39%), South Africa (29%), Kazakstan (12%), and India (8%).A number of grades of FeCr are available to producers of stainless steel, including high-carbon ferrochrome (HCFeCr) (Gasik, 2013). HCFeCr typically contains 60–70% Cr and 4–6% C (Basson and Daavittila, 2013). When the chromium content is lower (50–55% Cr) and the carbon content higher (6–8% C), it is referred to as charge chrome. Charge chrome is typically produced in South Africa due to the grades of ore available.FeCr is produced in submerged arc furnaces (SAFs) and in open arc furnaces (Mc Dougall, 2013) by carbothermic reduction of oxide raw materials. In a SAF the electrode tips are submerged in a porous charge mix. In FeCr production, the electrical energy is mainly liberated by resistive heating of the wet coke bed (Barker et al., 2007; Steenkamp et al., 2017). Thermally conductive lining design philosophies are typically applied in SAFs producing FeCr (Steenkamp, Denton, and Hayman, 2017; Coetzee, Duncanson, and Sylven, 2010; Coetzee et al., 2010).In July of 2016 and June of 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA SAFs producing FeCr in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Both SAFs were operated on the same site, by two different operating crews, using the same raw materials. The major difference between them was that the SAF excavated in 2016 was an open SAF (referred to as Furnace A) and the one excavated in 2017 was a closed SAF (referred to as Furnace B). In an open SAF, a gap exists between the top of the steel shell and the roof, with the top of the burden being open to the atmosphere and the CO-rich off-gas being combusted as it escapes. In a closed SAF, the roof is attached to the steel shell and the CO-rich off-gas is collected from an offtake on the roof for further treatment and used in downstream processes.The paper presented here reports the macro-scale observations on refractory wear for the two SAFs, and studies the potential for chemical wear of refractory by slag and alloy as a potential contributing factor to the tap-hole wear observed."

Jun 1, 2019

By R. J. Pine, J. M. Rance, J. S. Coggan

ABSTRACT: The safe design of excavations created in a fractured rock mass is of paramount importance in rock engineering. Depending on the nature of the stress regime acting on an excavation, and the associated deformational behaviour of the rock mass surrounding the excavation, a number of potential failure mechanisms exist. These involve a combination of shear failure on existing joints, extension of critically oriented joints and propagation of new fractures through previously intact rock. Conventional numerical codes usually adopt either a continuum or discontinuum approach; this often results in significant over simplification and kinematic limitations particularly when modelling complex rock mass behaviour in the close vicinity of excavations. This paper describes the results from several case examples using a combined finite element-discrete element code, ELFEN that incorporates a crack propagation mode. Through the use of selected rock engineering examples, the authors demonstrate the potential of the code in the realistic simulation of complex rock failure both in underground and surface excavation applications. RÉSUMÉ: La conception sûre des excavations créées dans une masse de roche fracturée est d'importance primordiale dans la géotechnique. Selon la nature du régime d'effort autour d’une excavation, et le déformation associé de la masse de roche autour de l'excavation, il exsite un certain nombre de mécanismes potentiels d'échec. Ceux-ci comportent une combinaison d'échec de cisaillement sur les joints existants, la prolongation des joints d’orientation critique et la propagation de nouvelles ruptures dans la roche précédemment intacte. Les codes numériques conventionnels adoptent habituellement l’approche, soit d’un continuum, soit de discontinuum; ceci a souvent comme conséquence une sursimplification significative et les limitations cinématiques en particulier en modelant le comportement complexe de la masse de roche très proche des excavations. Cet article décrit les résultats de plusieurs exemples de cas en utilisant un code qui s’agit d’une combination d’élément discret et d'élément fini, ELFEN qui incorpore un mode de propagation de fissure. Par l'utilisation des exemples choisis géotechniques, les auteurs démontrent le potentiel du code dans la simulation réaliste de l'échec complexe de roche pour les applications aux excavations soit au fond soit à l’extérieure. ZUSAMMENFASSUNG: Das sichere Design der Aushöhlungen, die in einer zerbrochenen Felsenmasse verursacht werden, ist vom paramount Wert in der Felsentechnik. Abhängig von der Natur des Druckregimes, das auf einer Aushöhlung und dem dazugehörigen deformationalen Verhalten der Felsenmasse umgibt die Aushöhlung fungiert, bestehen eine Anzahl von möglichen Ausfalleinheiten. Diese beziehen eine Kombination des Scherausfalls auf vorhandenen Verbindungen, Verlängerung der kritisch orientierten Verbindungen und Ausbreitung der neuen Brüche durch vorher intakten Felsen. Herkömmliche numerische Codes nehmen normalerweise entweder ein kontinuum oder discontinuum Annäherung an; dieses ergibt häufig bedeutende Übervereinfachung und kinematische Beschränkungen, besonders wenn es kompliziertes Felsenmasseverhalten in der Nähe der Aushöhlungen modelliert. Dieses Papier beschreibt die Resultate von einigen Fallbeispielen mit einem kombinierten begrenzten Element - getrennten Elementcode, ELFEN, das einen Sprungausbreitungmodus enthält. Durch den Gebrauch von vorgewählten Felsentechnikbeispielen, demonstrieren die Autoren das Potential des Codes in der realistischen Simulation des komplizierten Felsenausfalls bei Anwendungen für beide Tagebaue und Untergrundsaushöhlungen.

Jan 1, 2003

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By A. D. Prokop, J. P. Rider

Along with increased production from longwall units has come the likelihood of increased worker noise exposures. In recent years, equipment has become larger, more powerful, and noisier than its predecessors. For these reasons, the Mining Division of the National Institute for Occupational Safety and Health (NIOSH) is investigating worker noise exposure on longwall faces and researching possible solutions to reduce this exposure. Part of this research effort involves studying the effect of covering the underside of longwall shields with acoustical material to reduce reverberating noise along the face. Experiments using acoustical absorptive insulation to cover the undersides of the shields, shearer body, and the shield supports were conducted at the full scale simulated long-wall test facility located at the Pittsburgh Research Center. Sound levels were recorded every 1.5 m [5 fl] along a 15.2 m [50 ft] section of the simulated face for all of the conditions tested. The analysis of the data indicated that a 2.0-3.0 dBA noise reduction was achieved between the shearer drums and a 4.0-5.5 MA attenuation was attained upwind of the headgate drum.

Feb 24, 1997

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By W. A. Krivsky, R. Schuhmann

Jan 1, 1962

By C. -T. Mutale, A. S. Tuling

Titanium can exist in three different oxidation states. Its oxides are numerous and in presence of iron and oxygen, iron-titanium oxide compounds can also form. Some of the oxides are non-stoichiometric, making the determination of the thermodynamic properties of titanium and its oxides in molten steel and in slag difficult. Therefore, for the assessment of titanium activity in molten steel using the electrochemical measurements of oxygen partial pressure, the identification of oxides in equilibrium with titanium is important. This paper reports on an investigation of solid titanium oxide inclusions, which have been identified by combining different methods of analysis on quenched samples. These samples were taken from a Fe-Ti-melt at 1600°C, quenched in cold water then mounted and polished for optical microscopy. The oxide inclusions were analysed using transmission electron microscopy (TEM) with energy dispersive spectroscopy (EDS). Both single crystal and polycrystalline diffraction patterns were used to identify the oxides by comparing the d spacings with those in the ICDD X-Ray Diffraction (XRD) database. XRD was used to analyse the oxide particles on the top of slow cooled samples. It was found in the TEM study that the similarity of the diffraction patterns of the various phases meant that unique identification was difficult to achieve in some of the diffraction patterns. However, TiO, Ti2O3, Ti3O5, Ti4O7were identified in quenched samples, while TiO2, FeO.TiO2and iron oxides were seen in slow cooled samples. It was also confirmed that the type of oxides is related to titanium content of the samples. Keywords: Titanium, Titanium Oxides, Iron, TEM, XRD, thermodynamic.

Jan 1, 2004

By N. A. D. Parlee, I. D. Shah, W. C. Phelps

THIS note reports on a continuation of a program on the thermodynamics of Fe-S-X systems in the "steel-burning" temperature range begun by Bock, Barloga, and parlee.' Small coils of 0.039-in.-diameter pure iron (Ferrovac-E) wire were equilibrated with Fe-S-0 melts in ingot iron crucibles under argon at 1324°C in the assembly shown in Fig. 1, the lower part of which was heated in a large Globar furnace. Fig. 1 shows (R) the coiled iron wire sample, (M) the Fe-S-0 melt prepared from desired proportions of ferrous sulfide and ferric oxide, (K) the iron crucible, (I) a mullite guide tube, (J) an alumina crucible, (L) alundum sand, (N) crushed mullite, (Q) hollow cylinders of K30 brick, (C) a steel rod, (B), (El, (F), (G), (P), and (O), details of brass water-cooled head, and (H) a mullite tube 2-3/4 in. ID and 26 in. long. The rod (C) bearing the sample could be removed at will and be replaced by a tube for sampling the melt, or by a thermocouple for comparing the melt temperature with a control thermocouple not far from the 2-3/4-in. mullite tube. After equilibration the iron coils were treated with acid to remove the outer layer of metal and then they were analyzed for sulfur by a standard combustion method. The melt samples were analyzed for oxygen by a variation of Lander's2 hydrogen-reduction method for mattes, and for sulfur by the ASTM combustion-iodometric method NO. E 30-47. When the results of some forty-two runs were examined it was found that the sulfur and oxygen contents of the equilibrated melts showed good consistency, in that the plotted compositions fell along the smooth curve shown in Fig. 2. The points on this curve represent the experimental compositions of melts in equilibrium with ?-iron (Fe-S-0) solid solutions. These solid solutions are saturated with sulfur and oxygen with respect to the melt and therefore have the same sulfur and oxygen activities as the melt. The curve drawn through the points therefore delineates the ? liquidus. It falls in such a position as to roughly confirm the liquidus curves of Hilty and crafts3 at 1200" and 1300°C which are

Jan 1, 1965

In some parts of the world explosions in mines are more commonplace events. Even in the more developed nations explosions have occurred in recent times. In some cases these mines have significantly lowered their lost time injury frequency rates and as such considered themselves to be ?safe? operations. The consequence of these explosions has been devastating. It is not just the loss of those underground, but also to the families that have lost people in them and the broader community that has lost friends, income, business opportunities, and in many cases support and sponsorships. It begs so many questions, ?What went wrong??; ?Why were the circumstances not foreseen??; ?What could have been done to prevent it??; ?How is it that no one stopped it, reported it, fixed it etc.??. Being held accountable for negligence, should not be overlooked, however this may not aid the processes required to find all the answers. If the nature of explosions is understood, the circumstances and tools to prevent them are readily available then the occurrence and reoccurrence are due to weaknesses or inadequacies of the systems of work or in the implementation of them. This paper restates the fundamentals of gas explosions, examines the options to control the underground environment through ventilation, gas management and monitoring, education and training. Case studies have been used to examine systematic failures in ventilation management. In some of these cases it is not so much, the system that had been developed, but the interpretation and implementation of the system that resulted in the failure and subsequent loss.

Aug 1, 2013

Adhesion of Escherichia coli onto Oxide Minerals - Extended DLVO Theory and Flotation Behaviour

Sep 13, 2010

By M Amanzadeh, S M. Aminossadati, B M. Masum, M S. Kizil, C R. Leonardi

Gas sensing systems are becoming more important in many industries such as oil, gas and mining operations. Particularly in underground coalmines, accurate and reliable monitoring of toxic and combustible gases such as methane, nitrogen dioxide, carbon monoxide and hydrogen sulfide is essential. Available conventional electrochemical sensors for gas measurements in underground coalmines suffer from shortcomings such as cross-sensitivity response, limited lifetime, high calibration cost, maintenance cost and safety. Recent studies have found that fibre optic-based gas sensors have potential to eliminate these issues. These sensors can also be used for long distance and distributed sensing of various gases, both of which are important for underground gas monitoring. The aim of this paper is to review the present underground mining gas monitoring systems and review the new generation of fibre optic-based sensing systems for use in underground coalmines.CITATION:Masum, B M, Aminossadati, S M, Leonardi, C R, Kizil, M S and Amanzadeh, M, 2017. New generation of gas sensors for underground coal mining applications, in Proceedings Australian Mine Vent Conference 2017, pp 189–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Paul Downing

A typical day for a blasting company includes what seems to be an infinite list of tasks dealing with numbers. Whether determining the exact amount of explosives material in inventory, the number of holes in the shot, the exact distance from the blast site to the nearest exposure, or the capacity of bulk hoppers, the accuracy of numbers is key to ensuring the safety of the public, property and personnel.

Jan 1, 2008

By Víctor Cárdenas

El presente trabajo describe el manejo de las herramientas de calidad que aportan a la reducción de riesgos en la compañía minera La Poderosa. Para determinar los defectos, causas y consecuencias, es necesario conocer el procedimiento de control de los mismos a través del diagrama de Ishikawa o el ciclo de PHVA. Esta metodología permite encontrar la solución a los problemas dentro del aseguramiento de la calidad, seguridad y productividad de una empresa, así como establece la fuente de la causa de los accidentes por lesiones, como de los daños a la propiedad privada. En consecuencia, su aplicación se ha estandarizado en las áreas de seguridad y medio ambiente de dicha minera desde hace dos años, obteniendo resultados muy satisfactorios como el Premio Nacional de Seguridad en minería subterránea otorgado por el ISEM.

Sep 13, 2001

By Tom C. Palangio

The mining industry has come to rely on imaging devices to monitor and record all kinds of activities. We use them to measure, improve the process, ensure security, increase production and automate machinery. Cameras can be installed in locations most people wouldn?t want to live and be our ?eyes? to record the events at that location. This paper discusses digital imaging, the equipment, methods, techniques and information that can be learned from digital devices used in mining operations. The guy who said ?a picture is worth a thousand words? probably understated it. Images are the perfect way to document conditions before, after and even during mining activities. Today?s wide choice of cameras, camcorders and other digital devices allow us to record most activities and events. The technology is advancing at a high rate. Digital cameras and camcorders are marvels of technology with high resolution optics, compact size, automatic time and date stamp, great battery life, shutters to freeze motion and computers to auto focus and eliminate jitter (image stabilization). Add to this the economical price and ease of use and everyone in this industry should be aware of the possibilities.

Oct 1, 2010