Search Documents

By Arash Maghsoudloo, Asli Can

"Abstract This paper presents a ground improvement implementation case under a raft foundation of a local hospital. The selected ground improvement method is Wet Soil Mixing (WSM) technique. Soil mixing is increasingly applied to environmental applications and ground stabilization in geotechnical projects. In this technique, weak soil is mixed with cementitious slurry to improve the characteristics of the soil. The investigated case is one of the pioneering WSM ground improvement technique implementation cases in Turkey. The soil profile is mainly consisted of low plasticity clay. The effect of ground improvement is verified by a series of laboratory tests and four in-situ pile loading tests. The results of in-situ pile load tests on constructed soilcrete columns showed an acceptable factor of safety for the bearing capacity of the WSM columns. Measured bearing capacities in all four tested columns were nearly 20% higher than calculated values. In addition, a set of samples are obtained from the constructed columns and unconfined compression tests have been conducted. The laboratory test results indicate that the selected cementitious slurry has a sufficient efficiency to form the stabilizing columns.IntroductionIn the construction industry, stabilization of the soft ground by lime or cement stabilization is a widely used technique. In ground improvement systems deep mixing method (DMM) results in the same stabilization in deep portions of the soft soil profile by mixing cementitious slurry by means of mechanical augers. The pioneering cases of modern deep mixing application can be traced back to the year 1970 that was used for the stabilization of marine soils below the water level for the construction of harbor structures (Terashi et al., 1979). Nowadays, DMM is shown to be a proper and efficient method for the foundation of the structures and embankments on land. Some recent studies also reported that reasonable settlement reduction range in the stabilized soils under the foundation of structures (Archeewa et al., 2011). In addition to reduction of the structural settlement under service loads, deep mixing methods are also utilized when there is a concern with contaminated soil and groundwater or groundwater control (Andromalos and Bahner, 2003).Although, the DMM is shown to be a successful method in numerous studies for improvement of a wide range of soil types such as organics, fine-grained, and coarse grained material, it has some limitations (Archeewa et al. 2011, Jameson et al. 2010, Jelisic and Leppanen 2004, Lambrechts and Roy 1997, Meyersohn 2007, Miki and Nozu 2004, Olsson et al. 2008, O’Rourke and McGinn 2004, Stewart et al. 2004, Yang et al. 2011). High soil density and stiffness could damage deep mixing rigs. Engineering properties of the soilcrete columns changes based on the soil type, water content and other factors such as organic content of the available soil profile, so properties of the generated soilcrete should be verified by a set of rigorous testing procedures (Puppala et al. 2004).Based on the general classifications presented in the ground improvement literature, deep soil mixing method is divided into two main types of dry or wet mixing methods. In the dry and mixing methods compressed air and water are utilized as the binder transporter medium respectively (Moseley and Krisch, 2004). In addition, DMM methods can be categorized based on the employed mixing methods during the construction. In this study, the main aim is to present and elaborate on the selected method is known as Wet Speed Soil Mixing (WSSM)."

Jan 1, 2014

By Peter Richards, Alexander Lewis-Gray, Mark Davies, Nicholas Katsikaros

"Gekko Systems developed the Gekko Resin Exchange Column (G-REX) in order to optimise the recovery of gold in complex leach-to-electrowinning processes, as an intermediate step using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin (Lewis-Gray et al, 2015). Operational experience has been gained at the CGT Ballarat Gold Plant in near continuous operation since 2008, treating unclarified concentrate leach solution. The extension of the technology to higher throughputs and more complex chemistry is discussed.Aurix®100 ResinAuRIX®100 resin is a cross-linked polystyrene alkaline resin developed by Henkel (Virnig et al, 1996). The resin beads are off-white in colour, spherical, with a nominal size of 100% +600µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal cyanide complexes from leach solutions with a pH less than 11.5. The higher end of the pH scale produces best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX®100 resin for use in its G-REX column as part of its unique suite of gravity gold handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realised with AURIX®100 resin, of around 4% to 12% in capital savings and 27% to 40% in operating costs (Virnig et al, 2004). Allied to this is that AuRIX®100 resin is not susceptible to fouling, that is, the resin does not load with inorganic salts or organic compounds which would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, in service a dilute acid wash is carried out periodically on the resin to unblock resin pores."

Jan 1, 2016

Fossil fuel consumption in the United States increased markedly over recent years, and future demands expect to be even greater. Coal, this Nation's most plentiful natural fossil fuel, will play a key role in fulfilling these demands. With expectations of increased coal exploitation, the U. S. Bureau of Mines authorized this project, the objectives of whi.ch were to prepare an authoritative report on current surface coal mining technology, to define current problems and possible solutions, and to project future developments necessary to assure adequate surfaced mined coal production to meet the Nation's future energy needs. These objectives we're accomplished by an extensive review of available published literature and data gathering field visits to active surface coal mines throughout the country.

Jan 1, 1975

By J. L. Holman

The Federal Bureau of Mines has conducted research to delineate factors affecting relative fabricability of electrowon and electrorefined copper. The Bureau's Rolla Metallurgy Research Center coordinated and participated in a statistical round-robin chemical analysis and performed impact tests on lead-doped copper specimens. In a series of round-robin analyses, cathode, bar, or rod from a domestic lot of electrorefined copper and electrowon copper from a domestic and a Peruvian source were analyzed for Pb, Fe, Bi, Se, Ag, O, S, Sb, and seven other elements. The electrowon cathode from both sources surpassed requirements for electrolytic cathode, although lead in the Peruvian lot exceeded specification for oxygen-free electronic grade. The least interlaboratory agreement was for oxygen analysis, Copper specimens, doped with up to ~300 ppm Pb and consisting of as-cast material (fine-grained or coarse-grained) and hot-rolled material, were impact-tested at temperatures to 871° C (1,600° F). Impact energy of fine-grained material dropped 26 pct with increased Pb up to 20 ppm and more gradually thereafter. Coarse-grained specimens fractured at lower energy with little dependence on lead. Hot rolling raised impact energy substantially. Grain structure is evidently as significant as lead in influencing workability. Some discussion is given of possible effects of oxygen, sulfur, and porosity.

Jan 1, 1978

By A. D. Fowler, M. T. Anderson

A phenomenological model is presented that relates Pb-Zn mineralisation to proximal geopressure zones. Typically, geopressure zones (GPZ) consist of masses of undercompacted sediment encapsulated within impermeable shales and are characterised by high formation fluid pressures. Heat flow is perturbed in some GPZ on account of their insulating properties. Geothermal gradients as high as 150 degrees C/km have been observed over short distances in the sediments of the US coast of the Gulf of Mexico. Some modern geopressure zones are known to reach temperatures of 120-150 degrees C at depths of 2.5-3.5 km. It is demonstrated that the zones may act as proximal sources of hydrothermal fluids, thus explaining the high temperatures of mineralisation observed in the deposits, which are hosted in basins characterised by thick, rapidly deposited, shale-rich clastic sequences

Jan 1, 1991

By Venda Oliveira P. J., Correia A. A. S., Danisi C. M.

"AbstractA laboratory study has been undertaken to establish common understanding of the creep phenomenon of a Portuguese soft soil chemically stabilised with binders. In order to study the effect of different stress levels on the strength and on the creep behavior of the stabilised soil, oedometer creep tests and unconfined compressive tests were performed at different curing times. Results show that the creep stress level does not influence the unconfined compressive strength. In addition, the creep phenomenon increases the unconfined compressive strength of the treated soil. Two different secondary compression indexes were recognized from the one-dimensional compression curve which increase with an exponential trend with the creep stress level.IntroductionConstruction on soft soils requires a mandatory soil stabilization work to improve mechanical characteristics of the natural soil. Deep mixing method is a worldwide employed ground improvement method, nevertheless the creep phenomenon hasn’t been yet thoroughly analyzed. Most of the published papers have focused on the analysis of the compressibility and the strength of the soil-binder mixtures without considering the creep phenomenon. However, numerical results (Venda Oliveira et al. 2009) have shown that although settlements that occur during the creep stage (namely creep strains) are less in case of treated columns, they are still important especially due to the high loads applied to the stabilised soil. The few published studies about creep behavior of soil-binder mixtures reveal that the stabilization of an organic soil with cement induces a reduction of creep deformations, which is related to the amount of cement used and that the increase of the organic matter of the soil has a negative impact on soil stabilization, further inducing a slight increase in the creep deformations (Venda Oliveira et al. 2012).As part of the current research the effect of different stress levels on the creep behavior of a soft clayey-silt soil was studied. The binder mixture used to enhance the properties of the soil had a specific composition and quantity. Unconfined compressive strength tests (UCS) and UCS creep tests were carried out at pre-set curing times in order to analyze the creep behavior of the soil-binder mixture. In particular five different creep stress levels were studied to understand its influence on the strength and on the compressibility of the stabilised soil. In addition, considerations about the secondary consolidation index are also presented."

Jan 1, 2014

By Raymond W. Henn

The 31th annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, in Golden, CO June 7-11, 2010. The field demonstration portion of the course was conducted June 10 at wlh Construction Co.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods performed under various field conditions.

Jan 1, 2010

By J. von Schéele

OXYFINESTM is an oxyfuel-based concept for in-plant recycling. It enables the possibility of fines, dust, sludge (without any drying step) and other by-products generated by the steel- and metal-producing industries to be recycled directly back into existing processes or a separate on-site unit. The results from a full-scale installation (20 000 t/a) and pilot-scale trials with dry and wet materials in the steel and ferroalloy industries are presented. The latter include materials arising from ferrosilicon, ferrochrome and silicon manganese production. The concept not only provides a solution to the problems associated with dust and sludge generated in metal production, it also turns these materials into a low-cost raw material which is useful for the same production process, thus replacing some of the raw material input. If required, it could also be used, possibly as an intermediate solution, to convert the dust or sludge into an inert material with a suitable shape. Under some conditions, a directly saleable product could also be obtained. The paper reviews this technology, its status and benefits as wells as its possibilities with regard to application in ferroalloy production. Keywords: recycling, fines, dust, sludge, ferroalloys

Jan 1, 2004

By Karsten Zimmermann

The paper presents a study on the influence of face retreat rate in longwall coal mining on surface subsidence. It shows possibilities to influence dynamic ground movement by using a specific and controlled winning regime. For this, a dynamic stochastic prediction model used by DMT in Germany will be proved and adjusted on the specific character of geology in the Northern Appalachian coal field. Occurring ground movements such as inclination, curvature and deformation can be analyzed under static and dynamic points of view. It is theoretically shown that the face retreat rate has only a small influence on the static deformation values, but directly affects rate and acceleration of subsidence and deformation processes. The study shows that because of low mining depth and high mined thickness, static deformation values have the largest impact to surface objects. This implies that high face retreat rates don?t affect the impact on surface objects.

Jan 1, 2007

The process of electrostatic separation was developed in the late 19th century, but did not make much headway for about 25 years. High dc voltages, of the order of 20 kilovolts, are involved, and the only means of obtaining such voltages at that time were by the use of frictional machines, such as the Wimshurst. These were not reliable, for two reasons:-a. If a spark discharge occurred it took an appreciable time before a steady voltage was again attained.b. In damp weather the machines were almost useless.In the first 20 years of the 20th century the advent of mechanical and vacuum-tube rectifiers led to promising developments of 'the process. In the early 1920's flotation became widely used commercially, and proved to be more reliable, and capable of wider application, than electrostatic separation. During the last 15 years or so, with a better knowledge of the fundamentals forming the basis of the process, electrostatic separation is beginning to compete with flotation, especially in the treatment of smallsizedgranular material, such as beach sands. Electrostatic separation can be, and is, widely used in many cases where flotation is impossible, such as in the cleaning of food products which must be kept dry.

Jan 1, 1950

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission In metal/non-metal mines over a wide frequency range from 0.2 -1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types Include 01 f shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most Important mining techniques. The results show that transmission at medium frequencies are optimum tor wireless mine communications, In agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 1, 1981

By Y Miyoshi, J Ishibashi

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Sea floor hydrothermal activity in the Okinawa Trough is considered a modern analog to ancient Kuroko-type volcanogenic massive sulfide (VMS) deposits. Recent scientific drilling projects at active hydrothermal fields have enabled us to conduct comparative studies on hydrothermal clay minerals between ancient and modern systems. Zonal distributions of clay minerals below the sea floor of an active hydrothermal field have been revealed, which is represented by the distinctive assemblage of clay minerals. Zone 1 consists mainly of montmorillonite and sometimes of kaolinite; Zone 2 consists of chlorite and chlorite-smectite mixed-layer mineral; and Zone 3 is represented by the co-occurrence of illite and chlorite, from shallow to deep. This zonal distribution is likely to be in accordance with that reported previously for the Kuroko-type ore deposit. Similarities are also recognised in chemical compositions of illite and chlorite, which are both abundant clay minerals in the vicinity of the ore deposit. While illite would be formed by interaction with the hydrothermal ore fluid, the formation of Mg-rich chlorite is attributed to Mg metasomatism caused by the involvement of sea water. Further studies, especially focusing on interactions between fluid and solid phases, would significantly promote our understanding of dynamic processes for the formation of VMS depositsCITATION:Ishibashi, J and Miyoshi, Y, 2015. Hydrothermal alteration process in active sea floor hydrothermal systems in the Okinawa trough, from a viewpoint of a modern analogue for the Kuroko-type volcanogenic massive sulfide deposits , in Proceedings PACRIM 2015 Congress, pp 481–486 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Donald W. Baggs

This report describes economic mining feasibility studies conducted by the Bureau of Mines to estimate mining costs in the Porcupine mining area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of three mineral deposit types: 1) massive sulfide deposits containing zinc, copper, and silver, 2) vein gold, and 3)disseminated gold. Cost estimates were developed using the Bureau of mines Cost Estimating S,-stem. Discounted cash flow rates of return were calculated using the Bureau of Mines MINSIM (mining simulation) computer program. Three sets of metal prices were used in the study based on recent historical price information. Underground longhole stope mining of a massive sulfide deposit containing 25 pct zinc. 1 pct copper, and 63.6 g/mt silver was found to be economic at high metal prices at a quantity of 13,200,000 mt ore. Cut-and-fill mining of a 26,400,000 mt massive sulfide deposit was found to be economic at medium metal prices. Open pit mining of a similar deposit was found to he economic at medium metal prices and 26,400,000 mt ore, or at high metal prices and 6,600,000 mt ore. Underground mining of a vein gold deposit was found to be economic at a grade of 17.1 g/mt medium metal prices and 1,320,000 mt ore. Open pit mining of a disseminated gold deposit was found to be economic at a grade of 1.71 g/mt medium metal prices and a quantity of 39,600,000 mt ore.

Jan 1, 1986

Mining and metallurgical processing of gold and base metal ores often results in solid wastes and effluents containing high concentrations of arsenic. In addition, arsenic can be released to the atmosphere from gold roasters and base metal smelters. Speciation of arsenic in roaster products, in a stack sample from a copper smelter, in organic soils impacted by smelter emissions, and in an anaerobic effluent treatment system at a smelter site was determined in order to broaden our understanding of the nature and occurrence of arsenic in a wider range of metallurgical wastes. Micro-XANES spectra obtained from iron oxide particles forming in a gold roaster indicate preferential enrichment of As3+ species in maghemite-rich domains and microlayers. In comparison, haematite-rich iron oxide particles are dominated by As5+ species. It appears that maghemite is retarding oxidation of arsenic and its volatilisation during roasting. Arsenic occurs as both As3+ and As5+ species in a stack sample emitted from a Cu smelter, confined to fine-grained secondary product layers accumulated on the surfaces of spherical Cu particles. This is probably resulting from condensation of As species upon cooling following their volatilisation during the combustion process. Soil samples collected at various distances from the Cu smelter are dominated by As5+ species including monomethylarsonic acid and tetramethylarsonium iodide as the organic arsenic species. The presence of reduced As3+ species highlights the importance of organic material influencing the speciation of arsenic and mineralogical transformations taking place within the soil profile. The XANES spectra indicate that arsenic occurs predominantly as aqueous arsenite species in the anaerobic treatment system, contrary to the conventional thinking of As retention by the formation of secondary sulfides.

Jan 1, 2008

By Frederick M. Fowkes

Dusts can be filtered out of air streams onto polymer surfaces by electrostatic trapping resulting from the spontaneous transfer of electrons upon contact between dust particles and the polymer surfaces. Such spontaneous contact electrification has been studied quantitatively in this contract with the aid of modern semiconductor charge-sensors with the aim of determining what basic principles govern the sign and magnitude of contact electrification. Information obtained by capacitance-voltage measurements of thin polymer films on silicon showed that charges as large as 4 x 1012 electrons per cm2 develop spontaneously, and that such a charge gives adhesional forces of 165 pounds per square inch (11 atmospheres). Direct measurement of dust polymer contact electrification, using silicon surface channel conductance sensors, also showed spontaneous charges of more than 1012 electrons per cm2. Some polymers can either donate or accept electrons. These included chlorinated polyethylene, chlorinated polypropylene, polyethylmethacrylate, and a copolymer of maleic anhydride with n-octadecylvinylether. Other polymers never accepted electrons but could donate electrons; these included polystyrene, pulychlorostyrune, polyvinylchloride, polyvinylacetate, a polycarbonate (Lexan), and cellulose tributyrate. Contact electrification studies were made with dusts (coal dust, a channel black, or a silica powder) contacting thin films of various polymers solvent-cast onto the semiconductor charge-sensor. Sometimes charging was instantaneous and sometimes slower, but in all but one case (coal dust on a copolymer of maleic anhydride with n-octadecylvinyl ether) the charge trunsfer was a donation of electrons by the polymer to the dust. Some

Jan 1, 1973

By Ned Baker

Details are given of a Hydride Fuel System to provide 5 kg of HZ to fuel a Caterpillar 3304 engine previously modified to operate on hydrogen fuel and intended to power an underground mining vehicle. The Fuel System was installed onto the engine and the Engine/Fuel System tested under cold start conditions and a full range of engine loads and speeds. Refueling tests were also performed. The fuel system tested will support full engine power and allow delivery of at least 3/4-power on a continuous basis, from cold start conditions.

Jan 1, 1983

By Ray H. S, Galgali R. K

It is well accepted that the blast furnace will continue as the main route for iron-making for many more years. However, its limitations have motivated researchers to look for alternative routes, particularly, those where non-coking coal is used for liquid iron production. Smelting reduction (SR), where coal and oxygen are used to produce liquid iron and power is now receiving serious attention. Several smelting reduction reactors are now operating in pilot plant scale and one or two have reached commercial status.

Jan 1, 1999

Power Point Presentation

Jan 1, 2007

By J. Szlazak, A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents the analysis of ventilation systems used in dead-end headings, while being drilled, in coal mines. Special emphasis is put on methane and dust hazard. Mathematical model for distribution of methane concentration in a heading is given as well. This model takes into consideration sources of methane emission and change in air flow rate due to leaks in a duct line. Solving equations presented in this article enabled giving dependencies describing distribution of concentration along the heading. On the basis of these dependencies there is a possibility of determining places with higher methane concentration and ways of combating this hazard. Determining the distribution of methane concentration in dead-end headings ventilated by a separate ventilation system is of great importance as far as work safety conditions are concerned. The information obtained may be of use when finding proper places for installing methane sensors. Three kinds of separate ventilation systems were distinguished: forcing, exhaust and overlap. The development in construction of fans and spare parts of a duct line enables using both forcing and exhaust ventilation systems in headings developed by continuous miners, with length above 1000 m, in the conditions of methane, temperature and health-detriment dust hazards.

Jan 1, 2003

By Mark Rybak

On Aug. 31, 2006, Tropical Storm Ernesto hit the city of Richmond, VA. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This article describes the fast track design, bidding and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft-sinking methods and final lining design all contributed to the success of this project. The storm inundated Richmond, VA with up to 305 mm (12 in.) of rain that, in some areas, caused widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed and caused local combined sewer and stormwater flooding. The collapsed sewer was a 2.4-m x 76-mm (8-ft- x 3-in.-) wide by 2.7-m- x 152-mm- (9-ft- x 6 in.-) high arch sewer that was constructed in the 1920s and later filled over with municipal solid waste and a soil fill cap to cur-rent elevations. A sinkhole was created in the area of collapse approximately 18 m (60 ft ) deep and 31 m (100 ft) in diameter. This caused the existing arch sewer to become blocked. As a result of this blockage, contaminated floodwaters reached depths in low-lying areas in excess of 8 m (25 ft).

Jan 1, 2008