Search Documents

By Bing W. Jong

A bench-scale evaluation of coal and coal waste materials as aggregate materials for use in longwall mine supports was undertaken as part of the Bureau of Mines Health and Safety program on ground control. Performance data were obtained on portland cement concretes (PCC) prepared with coal and coal wastes as aggregate materials. The effects of high-early-strength accelerators on strength and creep and of superplasticizers on strength properties of PCC formulated with coal and coal waste were investigated. Concrete formulated with a high-early-strength accelerator and coal and coal waste has 20 and 40 pet greater compressive strength, respectively, than the control samples without admixture. A concrete formulated with coal waste and the high-early-strength accelerator, using four bags of cement per cubic yard and a water-cement ratio of 1.0, had the lowest creep value of all the coal- and coal-waste-formulated PCC's tested.

Jan 1, 1983

By Brian H. Greene

The U.S. Army Corps of Engineers, Pittsburgh District, is in the final phases of modernizing the locks and dams on the Monongahela River. One facet of this modernization is to replace the existing Locks 4 located on the Monongahela River approximately 40 river miles upstream from Pittsburgh, Pennsylvania. The existing locks consist of a 56-foot x 720-foot main chamber and a riverside 56-foot x 360-foot auxiliary chamber built in the 1930s. Two new lock chambers, each 84-foot wide by 720-foot long, will be constructed at the location of existing Locks 4 and will be named Charleroi Locks. The purpose of the new project is to facilitate navigation on the lower Monongahela River. Pittsburgh is currently the second largest inland waterway port in the nation, and the new locks will be an important component of the navigational infrastructure. The existing lock walls are of mass concrete construction and are founded on wooden timber piles driven to rock through alluvial sands and gravels. The new lock walls were designed to be supported by approximately 300 reinforced concrete drilled shafts, varying in diameter from 4 to 6 feet. To handle axial loads, the drilled shafts were designed for end bearing, with some skin friction. The tips of the shafts will be founded within competent rock. Since the walls will undergo lateral loads, the drilled shaft design also had to consider this loading condition. Some of the drilled shafts will be installed within coffer boxes, which will incorporate a tremie concrete seal down to top of rock. Complicating the design even further was the fact that some portions of the new walls will be supported by shafts that extend some 9 feet above top of rock through alluvial soils, producing a cantilever effect. The first phase of the new lock construction was initiated in the summer of 2005 with a contract awarded to replace the river wall. This required shutting down the existing riverside lock chamber and diverting all river traffic to the longer existing land chamber. The foundation of the new river wall will use 144 drilled shafts. To optimize the design embedment of drilled shafts in rock for the river wall, an exploratory drilling program was conducted by the contractor in July and August, 2005. Based on the quality of the sedimentary bedrock, the shafts will be embedded in rock from 31 to 38 feet. To achieve adequate end bearing resistance, the tips of each shaft will extend through predominantly claystones into a more competent siltstone unit for a minimum embedment of one foot. The contractor also performed an exploratory pile driving program to aid in the construction of the drilled shaft casing and the cut off walls that will encapsulate the river wall. Two demonstration drilled shafts located outside the footprint of the new river wall, will be constructed prior to the drilling of any production shafts. The demonstration drilled shafts will verify that the contractor is able to meet the design criteria and quality requirements of the contract. The river wall contract is currently underway and is scheduled to be completed in 2010.

Jan 1, 2006

By L-B Fu and J Tan, J H. Wei, N Tian

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Kendenggaoer-Kuokuqueke region lies in the western part of Chinese North-western Tianshan. New laser ablation inductively coupled plasma mass spectrometry zircon U-Pb geochronology for five separate granitic plutons for this region reveal two distinct intrusive periods: late Devonian (367~361 Ma) and late Carboniferous (315~301 Ma). These intrusions all share an arc-like geochemical affinity (ie enrichment of large ion lithosphere elements and negative anomalies of Nb, Ta and Ti). In situ zircon Hf isotopic compositions further differentiate the magmatic cycle, with the late Devonian intrusions yielding more depleted eHf(t) (+1.47~+6.54) composition than the late Carboniferous intrusions (eHf(t) = +4.95~+9.79). These geochemical data suggest that they might be mainly derived from different source regions and the tectonic setting was transformed into post-collisional in the late Carboniferous. As in many significant porphyry-ore districts, this dramatic tectonic reconfiguration, combined with melting of an evolved crust, resulted in genesis of metal-bearing melts. Furthermore, we can show that Neoproterozoic mafic juvenile lower crust intruded by mantle-derived melts and/or partial melting of slab material generated hybrid primary magma during subduction of the Palaeo-Junggar oceanic crust in the late Devonian. Whereas underplating of mantle-derived magma contributed more to the Late Carboniferous post-collisional magmatism.CITATION:Tian, N, Wei, J H, Fu, L-B and Tan, J, 2015. Timing and geodynamic setting of the late Palaeozoic polymetallic mineralisation in Chinese north-western Tianshan – insights from geochronology and petrogenesis of granitoids , in Proceedings PACRIM 2015 Congress, pp 171–174 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

By Jerome Apt

This report presents the methods and results performed pursuant to the U. S. Bureau of Mines contract entitled "Noise Abatement in Mining Machinery," Number H0122054. 2.1 Background Until the Congress of the United States created and passed Public Law 91-173, the Federal Coal Mine Health and Safety Act of 1969, there were no directly-applicable standards for noise exposure for underground coal miners.1 Section 206 of this law, approved December 30, 1969, provided for standards of noise to be applicable to each coal mine. It is as follows:

Jan 1, 1975

By Robert A. Cummings

A rock mass classification system has been developed for support estimation in mines using caving methods. The developed system (MBR System) accepts readily-obtainable geotechnical properties, and mining geometry, to develop a rating that permits recommendations for drift support in block caving mines. The data base includes major active United States caving mines. The method is intended to be used for planning and estimating purposes and for preliminary support design. The Manual explains the organization and nature of the MBR System, its derivations, details of required input data, methods for assessing the data and for developing rock mass ratings, and techniques for selecting the most appropriate mine support recognizing mine requirements and desired stability. A worked example is provided.

Jan 1, 1984

By Giuliana A. Zelada

This paper reports on a study of 43 compression load tests (five fully instrumented) and ten pullout tests of auger cast-in-place (ACIP) piles in sand. Eight design methods reported in the literature were used to predict the measured pile capacities. Ultimate load capacities of the ACIP load tests were determined using two different definitions of ultimate capacity and compared with predictions. Load transfer behavior was determined from a study of the fully instrumented pile tests and compared to predicted values. Recommendations are made regarding the design approach most appropriate for these foundations and the best procedure for estimating ultimate capacity from pile load tests.

Jan 1, 2000

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rim. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By Phillip R. Moyle

Several deposits in the Sheep Hole/Cadiz Wilderness Study Area (WSA) have small identified or potential for undiscovered gold and silver resources. One prospect area is a potential target for molybdenum. Most base and precious metals and one uranium deposit in the study area are of the fissure-filling, contact metamorphic type associated with late stage fluids of the Cretaceous Cadiz Valley batholith. Some evidence suggests limited Tertiary and Quaternary mineralization. Mineral deposits are controlled by faults, shear zones, and joints which strike northwest and dip northeast or southwest. Although undefined, calcium, sodium, lithium, and strontium brines are inferred within the study area. Some potential for oil and gas and geothermal resources is indicated by the interest private industry has shown in the eastern part of the study area. INTRODUCTION The U.S. Bureau of lines and U.S. Geological Survey conducted a mineral survey of the Sheep Hole/Cadiz Wilderness Study Area (p1. 1) which encompasses approximately 205,000 acres (83,000 ha) in south-central San Bernardino County, California. The U.S. Bureau of Mines studied the mineral resources of mines, prospects and mineralized areas; geological, geochemical, and geophysical investigations were conducted by the U.S. Geological Survey.

Jan 1, 1982

By David Bigby

In the UK, it is becoming increasingly necessary to open new longwall mining areas above old, abandoned workings. In such cases, strategic and gate roadways must often be driven and maintained across highly stressed areas and pre-existing and sometimes only recently formed subsidence troughs. Ground control at the edges of the subsidence trough can be particularly problematic, with complex combinations of stress and rock conditions being encountered depending upon the precise position in relation to underlying pillar edges. For economic recovery of these reserves, it is essential that rockbolt support is used wherever possible. It is therefore very important to the industry to develop its understanding of ground conditions and support requirements in these areas. This paper describes; ? the historical background to these problems and a series of documented UK case studies from the last 20 years. ? the experiences at UK Coal?s Riccall colliery, where a number of longwall panels were worked at a depth of around 800m, some 65m above previously worked longwalls. Actual experience is compared with pre-mining expectations and model predictions. ? design considerations and experience to date at UK Coal?s Welbeck and Thoresby collieries, which are embarking upon a series of longwalls in the Deep Soft seam, 30-40m above previously worked longwalls. The paper outlines numerical modelling techniques used to optimise such mine layouts within the complex geological and geometric constraints of a mature coalfield. These involve combinations of 2D and 3D finite difference and 3D boundary element models. It also discuss new modelling approaches which will be investigated in forthcoming EU funded research.

Jan 1, 2007

Excavations in rock are commonly supported with wire mesh, shotcrete, wire mesh and shotcrete in combination, and shotcrete reinforced with various types of fibres. Wire rope lacing and various types of straps are additional forms of support installed over the above types, to cope with severe conditions. These support systems are very important items of ?membrane? rock support. With the recent development of several types of thin sprayed linings, the importance of membrane support is likely to increase in the future. In this paper, a wide range of mechanisms of membrane behaviour and mechanisms of loading of membranes, is described. The concepts of membrane components, which are single membranes that may be used on their own as rock support, and membrane systems, which are combinations of more than one membrane component, are introduced. Different situations have different requirements of membrane support, and differences between civil engineering and mining requirements are highlighted. With the different basic requirements in these two areas, the requirements of rock support are correspondingly different. A thorough understanding of the mechanisms of behaviour of the different types of membranes, and the different mechanisms by which the membranes are loaded, is essential before a selection of appropriate support can be made, before appropriate design methods and calculations can be determined, and before appropriate performance test methods for membranes can be defined. The material in this paper contributes towards the understanding of membrane support behaviour.

Jan 1, 2001

A systematic study of groundwater conditions at eight underground mine sites exhibiting a wide range of groundwater qualities throughout Australia has been completed at the WA School of Mines. This has resulted in a new corrosivity classification for groundwater driven corrosion processes for cement grouted cable strand used in the Australian underground mining industry. The new corrosivity classification is simple to use and corrosion rates may be predicted from readily obtained in situ measurements of groundwater dissolved oxygen.

Jan 1, 2008

By William A. Beck

The Construction Aggregates Corp. operates a plant for processing sand and gravel from two deposits in Ottawa County, Mich. The bulk of the sand is obtained from a sand dune on the shore of Lake Michigan, and the gravel is dug from a glacial-drift deposit farther inland. Mining is done with draglines, and the material, both at the digging site and in the plant, is moved mainly by systems of conveyors. The Ferrysburg plant serves customers along the Great Lakes, which is unusual for a business normally local in character. Annual production exceeds 1-1/2 million tons of sand and gravel as concrete aggregate and 200,000 tons of core sand for foundry use.

Jan 1, 1962

"The first SkimAir flash flotation cell was installed in Outokumpu’s Hammaslahti Copper Concentrator in 1982 to prevent overgrinding of soft sulphides in the milling circuit. Since this first installation the popularity of the flash flotation has fluctuated depending on metal market conditions and regional preferences. Units have been installed in many commodities including copper, lead, gold, PGMs, silver and nickel. Though it has been successfully employed in many operations around the world, flash flotation technology is still not well understood by many in the mining industry. This paper will discuss aspects of flash flotation flowsheet development along with some of the metallurgical and engineering considerations required to successfully incorporate flash flotation into new or existing milling circuits. This paper will also try and debunk some of the myths that exist around flash flotation cells and their operation. Case studies of flash flotation implementation will be discussed.IntroductionModern flash flotation technology was developed several decades ago by Outokumpu, with the first commercial installation of this technology being at the Hammaslahti concentrator in Finland in 1982 (Kallioinen & Niitti, 1985). This was a relatively modestly sized SK80 cell producing final grade copper concentrate directly from the flash flotation cell operating in the grinding circuit. Since that time the size and number of flash flotation cells installed globally has grown considerably to the point where today, it is a widely known application of flotation technology for amenable ores. Owing to their long history in developing the technology, Outotec are the market leader with their SkimAir range of flash flotation cells. Though there is a general awareness of flash flotation process in the mineral processing industry, there is a lack of detailed understanding of the process and the benefits it can provide to new and existing operations."

Jan 1, 2017

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

Advances in Coarse Particle Recovery - Fluidised-Bed Flotation

Sep 13, 2010

By J Watt

The Hidden Valley Gold Project is located in a remote and mountainous area of the Morobe Province approximately 30 km south of the township of Bulolo and approximately 90 km south-southwest of the provincial capital, Lae. The Hidden Valley deposit was discovered in 1984 with the nearby Hamata and Kaveroi deposits discovered in 1987 and 1992 respectively. Reserves (Harmony, 2009) at these three deposits are 42.1 million tonnes of ore containing approximately 2.9 million ounces of gold and 45 million ounces of silver. A further 5.4 million ounces of gold and 84 million ounces of silver are in the resources category. The process plant is designed to treat 4.2 million tonnes per year of gold/silver ore extracted by open cut mining methods. Ore is classified into three ore types according to oxidation state: oxide, transition and primary. The silver to gold grade ratio is high for the Hidden Valley and Kaveroi ores, generally in the range 15 - 20:1, and much lower for Hamata, typically 1 - 2:1: Primary ore is the dominant ore type at Hidden Valley with sulfur grades up to about two per cent sulfur. Oxide and transition ores are more prevalent at the Hamata deposit, but its primary ore has up to five per cent sulfur grades. Variable ore types, particularly in the initial years of operation, high silver to gold ratios and limited plant site area, due to the challenging terrain, present the main processing challenges for this project. This paper describes the operating strategies and process development for the main areas of this circuit, highlighting selections of processes and equipment that achieve cost effective, yet flexible solutions to the treatment of ores from these deposits.

Jan 1, 2009

By Peter Florian

At 5:50 am on October 1, 1992, the new $800 million Pittsburgh International Airport Midfield Terminal opened its gates to the world after five years of construction and more than 24 years of planning. Despite numerous design changes, this massive project was completed on time and substantially within budget. The importance of this airport to Allegheny County and the Pittsburgh region was recognized 24 years earlier by Allegheny County Commissioners Tom Foerster and the late Leonard Staisey. Staisey and Foerster established a program to acquire land for the "Airport of the Future".

Jan 1, 1993

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints.

Jan 1, 2002