Search Documents

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

By Roy L. Wilfong

The thermal decomposition of the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of praseodymium, neodymium, and samarium was investigated thermogravimetrically in the temperature range 25° to 1,500° C. Each salt was decomposed at a heating rate of 2.5° C, per minute. The pyrolytic sequences have been identified and the temperatures of formation of inter-mediates, the minimum oxide formation temperatures, and values for loss on ignition have been determined. The nonstoichiometric ranges between Pr6011 and Pr203 and the extent of these ranges have been determined for oxides derived from the carbonate, nitrate, and oxalate salts of praseodymium. The alum and sulfate salts of praseodymium produced the sesquioxide without forming the intermediate non-stoichiometric oxides. The temperature limits of formation and regions of stability for the alums and sulfates were better defined than were those for the carbonates, nitrates, and oxalates. The minimum oxide formation temperature increased in the order of samarium, neodymium, and praseodymium irrespective of the anion.

Jan 1, 1962

By Brian R. Zuckerman

The Capitol Area East End Complex is currently being constructed under contract with the State of California Department of General Services on two sites adjacent to the grounds of the California State Capitol Building in downtown Sacramento. The complex will consolidate the headquarters of the Departments of Health Services and Education, which currently occupy several facilities located throughout Sacramento. When completed in 2003, the complex will be the largest civic office project in California history, with approximately 1.5 million square feet of office space and housing nearly 6,300 state workers. The total project is being constructed on five separate blocks in downtown Sacramento, Blocks 171 through 174 and 225. Separate design/build contracts were executed for the construction on Blocks 171 through 174 and the construction on Block 225. The scope of this paper is limited to construction on Blocks 171 through 174, which comprise a square, two blocks on a side, bounded by 15th, 17th, L, and N streets, located immediately to the east of Capitol Park and the State Capitol Building, as pictured in the image shown below.

Jan 1, 2002

By R. E. Simpson

Beginning in 1972, fully grouted resin bolts were used in underground mines. An estimated 20 million resin bolts will be installed in 1980 owing to their apparent support improvement in most roof-bolt applications. Inorganic cements were tested to replace the resin at a lower cost while retaining the advantages of a grouted bolt. Although other inorganic materials were considered, all but portland and gypsum cements were rejected for reasons of availability, performance, or cost. Portland and gypsum-type cements were tested by the Bureau of Mines to select a fast-hardening, low-cost material that would anchor a roof bolt adequately to meet safety standards. An alpha-gypsum cement, accelerated with potassium sulfate, was selected as the best material because it had adequate pull strength at a desired set time of less than 5 minutes and was readily available.

Jan 1, 1980

By T P. Fischer, S N. Williams, N C. Sturchio

Chemical and isotopic analyses of fumarole gases from Galeras Volcano, Colombia provide significant insights into the origin of volatile components in the magma. Water comprises a mixture of magmatic (rock-equilibrated at high temperature) and meteoric, with the relative proportions varying through time. Carbon isotopes are most consistent with a mantle source, although other contributions to the system cannot be ruled out. Nitrogen most likely originated from organic matter in subducted oceanic sediments. All of these 'primary' components have been modified somewhat by interaction or exchange with other reservoirs during ascent to the surface. In addition to information on the origin of the gases, these data show significant temporal variations precursory to eruptive events. Chemical ratios change and water becomes more meteoric in character prior to eruptions.

Jan 1, 1995

By W. Biermann

All industrial processes are economically driven, resulting in the ever increasing need for process optimization in order to stay competitive and profitable. Numerous models has been published depicting the optimization of the raw material usage in an arc furnace, as well as the thermal and electrical efficiency; however, to obtain a holistic view of the cost-effectiveness of the process one needs to expand the model to include the cost of all the operational variables. This project therefore aimed to not only include the raw material feeds and power consumption as input variables, but also the labour, maintenance, and environmental costs to generate an all-inclusive financial balance. In the end, the model was able to mathematically optimize the ferrochrome (FeCr) production process through evaluating the effect of a specified combination of input parameters. It could therefore be used as a tool to aid in managerial decision-making; to appraise and correspondingly adjust certain operational variables in order to achieve a maximum return on investment. This paper fully describes the reasoning behind the choice of the essential model components, the assumptions made during the models development, the calculation approach, as well as the advantages, limitations, possible applications, and areas for expansion of the final model. Through running simulations with plant data, it was found that the accuracy of final model remained fairly constant when applied to stable furnace conditions, but was met with a number of limitations when applied to more complex situations. These limitations could, however, be overcome through further development and expansion of the existing model to include a larger number of process variables.

Jan 1, 2012

By E. H. Boswell, E. M. Cushing

The Mississippi embayment east of the Mississippi River is part of a vast geologic and hydrologic province. The abundance of water available is largely responsible for the agricultural history of the area and is perhaps the key factor in the rapidly accelerating trend toward industrialization. The multiple artesian aquifer systems that underlie the region and the alluvial aquifer along the Mississippi River are virtually undeveloped sources of fresh water in that they are yielding only a fraction of the water available. The potential yield of the 12 aquifer systems is estimated to be about 25,000 mgd (million gpd) of which only about 600 mgd is presently being withdrawn. The amount of water in storage in these systems is about 1600 trillion gal. Ground water having a dissolved-solids content of less than 500 ppm is generally available at depths of less than 1000 ft, and water having a dissolved-solids content of less than 1000 ppm is available in some places to depths of more than 3000 ft. Iron is the most common troublesome chemical constituent in the ground water. Water in varying amounts is also available from streams within the region. The amount of water which originates within the region and which leaves it as streamflow during a year averages about 50 million acre-ft (about 45,000 mgd). An additional 375 million acre-ft (about 340,000 mgd), which originated outside the region, leaves the region as streamflow during an average year. Some streams have considerable flow during periods of no precipitation and the water during these periods generally has a low dissolved-solids content. Large quantities of water from streams and waterbearing sands (aquifers) are available in the Mississippi embayment east of the Mississippi River. Most of the region is underlain by aquifer systems that will yield large quantities of water to wells, making ground water the most readily available source of fresh water. About 90% of the water used in the region is obtained from wells. Streams have been used primarily to dispose of, and dilute, wastes that have been dumped into them. The Mississippi, Ohio and Tennessee rivers, and the lower parts of the Tombigee and Yazoo rivers also serve as a means of transportation. This nominally water-rich region receives from 48 to 56 in. of precipitation in average years and is crossed by several large rivers. The largest, the Mississippi River, is the western boundary of the region discussed in this paper. The economy of the region is basically agricultural, but industry has become increasingly important since World War 11. The diversification and mechanization of agriculture have resulted in a surplus of manpower, most of which is being absorbed by the expansion of industry. Further industrial expansion probably will occur because of the available manpower, natural resources and economical transportation. Increasing demands on available water supplies will be made and the future economic growth of the region will be largely dependent upon wise utilization and management of the water resources.

Jan 1, 1969

The Mount Lyell Mining Field is Australia's chief productive source of copper. It is situated near Queenstown, on the western flanks of the West Coast Ranges, about 20 miles from the west coast of Tasmania (Fig. 1).The following observations on the mineral composition of the copper ores of the Mount Lyell Field are based on a...

Jan 1, 1939

By A. U. Miller

"Ventilation is one of the meet important factors in mining, although until recent years less thought has probably been given to effective ventilation than to any other one phase of mining. In the past, very little, if any, attention was given air courses until they became so constricted by falls that the volume of air was greatly reduced; and, in addition, the stoppings and doors were so poorly constructed that only a very small percentage of air reached the face workings.As a matter of fact, mines have been visited where the volume of air being circulated in certain sections was much larger than in others, and where the management was striving to increase the flow of air in those sections with the least air current, believing the ventilation to be deficient. After sampling and analyzing the return air from the various sections in such mines it has been found that the quality of the air in certain places with the largest flow was more impure than in some of those with the least flow.In past years, practically all mine fans were operated by steam-driven engines supplied with steam from the mire boiler plant. No check was made on the steam consumption or the power cost of operating the fan, therefore the management had very little if any definite information as to cost of ventilating the mine.With the increased use of electrically-driven equipment in mines electricity is being used more and more to drive mine ventilating fans, and since in many instances the current is purchased from central power plants operators have come to realize that in many cases the cost of operating the fans is very high. Some engineers estimate that it ranges from 20 to 50 per cent of the total power cost of the mine. This information, together with the fact that mines are now being developed on a larger scale, requiring larger quantities of air for the men to dilute the gases liberated, has caused the large progressive companies to make, a more comprehensive study of mine ventilation, resulting in a decided improvement in the quality and quantity of air at the face workings, as well as reducing materially the ventilating costs."

Oct 1, 1930

By G. Bierie

The conveying of bulk materials is prone to problems. These problems can reduce the capacity and efficiency of the plant, and even threaten the health and safety of the workforce. This presentation will look at new conveyor technologies systems, and how, used separately or in combination, they can improve material handling.

Jan 1, 2007

By Cadman S. J

( The central part of the Gippsland Basin is surrounded by existing major Petroleum accumulations and although six exploration wells have been drilled in the area, none are significant petroleum discoveries. Post drilling analyses indicate that the wells were drilled off structure due to the presence of high-velocity Miocene channels. These channels contain carbonates of significantly higher interval velocity than the surrounding sediments. Problems with seismic interpretation were thus encountered in the development of prospects in the central part of the Gippsland Basin as part of a BMR prospectivity study. The seismic interpretation problems associated with the Miocene channels are two-way time pull-ups at the underlying top of Latrobe Group and deeper levels on the seismic sections. Interpreted seismic sections passing through some of the exploration wells and the Miocene channels are presented to illustrate the configurations of these channels and the pullup effect associated with them. Two different methods of depth conversion were applied, one for the area below the high velocity channels and the other for the area away from the channel. The application of these two methods of depth conversion were found to be reasonably successful in correcting for the pull-ups caused by the high velocity Miocene channels. Mapping of the events near the top of Latrobe Group and near Base Lower L balmei seismic horizons has led to the identification of several potential structural closures. Further exploration efforts are necessary in this area to test these closures.

Jan 1, 1992

By C E. J de Ronde, J L. Mauk

Sulfide chimney samples collected during the 1998 - 1999 R/V Atlantis û DSV Alvin 3 - 30 research cruise have been examined and classified into four types, based on common characteristics. Chimney morphology is the most important characteristic and resulted in the following groups: 1. flutes, 2. cones, 3. wide-flats, and 4. beehives. Other characteristics resulted in the classification of subgroups within the flute, cone and wide-flat groups. The combination of characteristics, including; the presence of an orifice, internal chimney fabrics, wall thickness, extent of weathering, and the presence of Alvinella worm casts, enable evolutionary trends between the different chimneys types to be established. These trends indicate that with time, flutes evolve from immature zoned chimneys with a central orifice and smooth thin-walls, into cone chimneys with thick walls and massive fabrics which have their orifices infilled by massive sulfides, and a rough exterior. Repeated mineralisation within, cones may result in the formation of wide-flat chimneys. Beehive chimneys can form at any time during chimney growth.

Jan 1, 2003

By Jack J. Ayotte, Michael R. Nadon

"Today's demand for better and more efficient methods inspires new approaches to construction and mine development.A project at Asarco's Aquarius Mine provided a challenge that resulted in the adaptation of a civil construction technique to a mining application.This paper describes the construction of an escapeway shaft to surface from the mine's 150m level. The prime consideration was to provide the most cost-effective method of establishing a shaft collar in the 145 ft (44 m) of water-bearing overburden. This problem was resolved with the employment of the drilled in-caisson method.The remainder of the 500ft (152m) deep shaft was raise bored and portable hoisting equipment was used to install a permanentmanway and shaft liner.IntroductionHaving completed the first phase of exploration development in 1982, J.S. Redpath Limited was engaged to carry out an engineering and cost study to investigate the feasibility of re-opening Asarco's Aquarius Mine near Timmins, Ontario. The scheme was to develop the proven ore reserves and proceed with shrinkage stoping while carrying out further exploration development and diamond drilling.One significant and costly component of the project was the provision of an escapeway shaft to supply additional ventilation as well as a second means of egress from the mine. The major complication to this task was the presence of 145 ft (44 m) of water-bearing overburden at the site. The first and obvious approach was to use conventional ground-freezing methods as had been employed previously on .this property for the initial development shaft. This being the only ""sure"" method available at the time of the budget estimate, it was used as a basis for the study but its considerable projected cost and time demand inspired further investigation into other possible solutions.After considerable research and several brainstorming sessions, a Redpath team came up with an approach whose basic procedures had been used extensively in the civil construction field, although they were novel to the mining industry."

Jan 1, 1987

By Michael Young, Peter Allum, Mingwei Gao

"Tough economical conditions and high grade but fine-grained ore processing have forced the mining industry to look for more efficient processes. Isa Mill Technology for ultra-fine and fine grinding is one such process employed at several mining operations in Australia including Mount Isa Mines Limited in Australia. Mount Isa Mines is a business unit of MIM Holdings Limited. MIM is an Australian-based international mining and mineral processing company with around 8000 employees worldwide. Major products include copper, gold, zinc-lead-silver, coal and technology sales.The Isa Mill is a horizontal stirred mill with sizes up to 3 m3 chamber net volume and 1 120 kW installed motor. It was jointly invented by Mount Isa Mines of Australia and Netzsch Feinmahltecknik GmbH of Germany for ultra-fine and fine grinding duties in the minerals industry. Isa Mill operations started in 1994 at the Mount Isa Mines Leadzinc Concentrator and then at MIM’s McArthur River Mine in 1995. These Isa Mills have been used to liberate sphalerite and galena at Mount Isa and silica at McArthur River by grinding to less than 7 micron.This paper discusses the Isa Mill Technology and reports on the metallurgical performance of the Isa Mills at Mount Isa Mines, including work done over the last 9 years to improve mill design, process efficiency and maintenance, which has resulted in the current state-of-the-art Isa Mill Technology.INTRODUCTIONThe current leadzinc deposits at Mount Isa Mines (George Fisher, Hilton and Isa) have an average grade of 10.5% zinc, 7.2% lead and 165g/t silver. Fine grinding, in particular in the zinc retreatment circuit requiring a milled product P80 of 7 micron, is essential to treat the ores from the Mount Isa Mines deposits. Every one micron size reduction in the zinc retreatment circuit below a P80 of 10 micron improves the overall plant zinc recovery by 1%, resulting in an increase in revenue of about 1 million dollars per annum."

Jan 1, 2002

By K. Thirumalai

The feasibility of breaking hard rock by thermal weakening and subsequent mechanical impacting was tested, Field tests at a basalt quarry in Dresser, Wis., demonstrated that large hard-rock blocks (5 by 5 by 5 ft) could be effectively reduced in size by this method. A series of secondary breakage tests, using air-propane heating, resulted in an average heating cost of $0.36 per ton. This combination energy approach provides an alternate means of size reduction of large hard-rock boulders for quarry and for underground are chute and grizzly operations where mechanical methods, used alone, are ineffective.

Jan 1, 1975

By Paul L. Campbell

Investigations by the Federal Bureau of Mines of methods of upgrading tar obtained by low-temperature carbonization of lignite showed that ß,ß?-oxydipropionitrile, ß,ß?-iminodipropionitrile, and ß,ß'-thiodipropionitrile were effective solvents for extracting aromatics (aromatic hydrocarbons plus polar compounds) from coal-tar neutral distillate fractions. Batch extraction showed that these solvents extracted approximately the same percentage of aromatics from various neutral oil fractions boiling between approximately 170° and 350° C. In continuous countercurrent extractions using oxydipropionitrile and iminodipropionitrile, approximately 30 to 35 vol.-pct, and 65 to 70 vol.-pct, of the aromatics in 170° to 350° C. neutral distillate oil were extracted at room temperature when solvent-to-oil ratios were 2:1 and 12:1, respectively. As the concentration of aromatics in the neutral distillate oil fraction decreased, the capacities and, to some extent, the selectivities of these solvents for the remaining aromatics decreased. Aromatics were isolated from the extracts and the solvents recovered by washing the extract fractions with a low-boiling paraffinic hydrocarbon such as heptane, using hydrocarbon-to-extract ratios of at least 2:1. The heptane wash removed most of the aromatics but only part of the polar compounds (compounds containing oxygen, sulfur, and nitrogen) from the extracts. The recovered oxydipropionitrile and iminodipropionitrile, containing polar compounds, were effective in extracting aromatics from neutral distillate oils. The contaminated solvents showed essentially the same capacities and selectivities as the pure solvents.

Jan 1, 1961

By W. A. Calhoun

The purpose of this investigation was to develop economical mineral dressing processes for removing objectionable quantities of impurities, such as quartz and pyrite, from refractory clay deposits in east central Missouri. The presence of excessive quartz in these clays causes crazing. Pyrite causes bloating and unsightly dark blobs on the surface of fired refractory brick. The iron concentration in the proper state of oxidation may also act as nucleation centers for carbon crystal growth which can result in bursting of the refractory. Numerous deposits, representing a very large tonnage, have been examined and prospected by various refractories companies and found to contain impurities in objectionable quantities. Upgrading these clays would greatly extend our reserves of high-quality refractory clays. Wet-tabling and wet-cyclone concentration were found to be effective for removal of impurities from clays. Of the two methods, wet-cyclone concentra¬tion would be cheaper and more effective. Although wet-tabling improved the refractory properties of each clay, beneficiation by wet-cyclone produced clays of superior quality. Clay recoveries by wet-cycloning ranged from 56.1 to 81.8 percent of the weight of the crude samples, and the beneficiated clays contained from 71.9 to 94.4 percent of the total alumina. The pyrometric cone equivalent (PCE) was increased from 1 to 3 cones by wet-cycloning. The beneficiated clays also met the reheat shrinkage requirements on refiring to 1,400° C. Missouri is one of the major domestic sources of fare clay. In addition to deposits of high-grade refractory clays, there arc many deposits that contain small percentages of impurities, which render the clays unfit for the production of high-heat-duty firebrick. Development of methods to beneficiate these submarginal clays to usable materials would greatly increase commercial fire clay resources.

Jan 1, 1961

By J. J. Lukasko

The U.S. Bureau of Mines developed an alternative electrochemical process for the production of calcium metal. The current industrial practice is costly, complex, and inefficient. The Bureau method involved electrowinning of a calcium-tin alloy followed by electrorefining to produce calcium metal. In the electrowinning cell, CaCI2 was fed to a KCI2-CaCI2 electrolyte. The calcium was electrowon at 6500 C into the pure molten tin cathode until the cathode contained 7.5 wt pct Ca. Current efficiency for electrowinning averaged over 90 pct. The resulting calcium-tin alloy served as the anode for the electrorefming cell, which employed a [CaC~-CaF2] fused salt as the electrolyte. Calcium metal was electrorefmed at 8500 C with a current efficiency of 85 pct based on calcium metal recovered. The calcium metal analyzed 99.2 pct, which is purer than commercially produced calcium.

Jan 1, 1990

By J. E. Campbell, A. W. Wesner, M. Pobereskin

This paper summarizes the results of an investigation sponsored by The Coates Steel Products Company. The objective was to determine the relative effects of certain chemical and physical properties on the wear resistance of grinding balls when grinding cement. In making this study, a number of types of balls were used in both dry and wet grinding in commercial ball mills. The radioactive-tracer technique was used in separating the test balls from the rest of the mill charge and in sorting the different types of halls that were all tested at the same time for each of the grinding operations. PROCESSING OF GRINDING BALLS In order to determine whether the properties of grinding balls, namely, composition, microstructure and hardness, can be related to the rate of wear, the halls used in this study were selected to represent various combinations of these properties. It was recognized that the mechanism of wear was not the same in the wet mill as in the dry mill. Therefore, the types of balls tested in each of the two environments were not necessarily the same. However, all of the types of balls evaluated in the dry mill were tested simultaneously for one time period, while those evaluated in the wet mill were tested simultaneously for three different time periods. All of the test balls were separated from the charge when the mill was dumped. All of the balls were of 0.940-inch diameter when charged, and all but the regular production balls were finish ground to this size to eliminate the decarburized surface layers. The steels and processing methods used, as well as the micro-structures and hardness levels of the balls, are described as follows: Regular production forged SAE 1095 steel balls were used in both the wet and dry mills. They were forged to a nominal diameter of 0.940 inch and quenched in oil from the forging temperature. Each retained a partially decarburized surface layer from the forging bar stock; the maximum depth of this layer was about 0.030 inch and the decarburization was negligible where the ball was sheared from the bar. The hardness at the surface was 40 to 46 Rock-well C in the partially decarburized area and 57 to 62 Rockwell C in the areas not decarburized. The hardened zone extended to a depth of about one-third of the radius. Below the decarburized layer, the hardened zone consisted primarily of hard as-quenched martensite with varying amounts of retained austenite. This structure changed to fine pearlite at a depth of about one-third of the radius. In order to eliminate the effect of the decarburized layer, a set of production balls of SAE 1095 steel was forged to about a 1-inch diameter, quenched in oil from the forging temperature, and ground on ball-bearing grinding equipment to a 0.940-inch diameter to remove the decarburized layer. The balls' hardened zones were similar to those in the previous set. The hardness of the finished surfaces was 52 to 60 Rockwell C. A slight amount of decarburization apparently remained after the removal of about 0.030 inch from the surface. Balls of this type were tested in the dry mill only. Another set of forged SAE 1095 steel balls of 1-inch diameter was heated to 1500 F and quenched

Jan 1, 1961

De Beers? Finsch diamond mine began operation in the 1960s as a surface project using the latest technology available. During the 1990s, the operation, located about 160 km (100 miles) west of Kimberley, South Africa, began its move as an underground mine. The earlier stages (Blocks 1, 2 and 3) of underground work at Finsch used open stope mining methods, also using the latest in technology. The mine began developing Block 4 in 2004. How-ever, studies on this level showed that block caving was a more efficient mining method than open stoping. It was during those studies that De Beers determined that Block 4 would be a good candidate for testing Sandvik?s automated truck haulage technology.

Jan 1, 2008