Search Documents

By I. Goy D. Gaballah

Decontamination of synthetic K2Cr2O 7 solutions containing 10 to 1000 ppm of hexavalent chromium using chemically treated barks have been studied at a laboratory scale. Metal removal from solutions depends on the pH, the initial concentration and the bark species. The use of a pulp density of 2 % in an agitated flask at the optimum pH for 2 hours leads to a percentage chromium removal of about 95 of the initial metallic ions content. Other trials conducted by column percolation permit the determination of the maximum retention capacity of the treated bark. Depending on the bark species, oak or pine, the rate of saturation is 110 and 215 mg of Cr per gram of bark respectively. The incineration of the metal charged barks gives recyclable, ashes containing 36 and 54 % of chromium metal for the oak and pine barks respectively. Experiments, of Cr6+ removal from industrial effluents containing up to 1800 ppm have been carried out on the semi-pilot plant scale. They have lead to the elimination of about 90 % of hexavalent chromium from this industrial waste solution. Further studies are conducted in order to define the hexavalent chromium binding mechanisms on bark constituents.

Jan 1, 1992

By lonkion M. Font

Due to the known disadvantages of the use of iron silicate slag in the nickel converting stage, i.e., high metal losses, high magnetite content, and low fixation of impurities in the slag, the development of the new proposed "ferrous calcium silicate slag" for smelting and converting processes of nickel is very promising. Hence, considering the successful experimental results of using CaO base slag for the nickel smelting process, a study based on a detailed comparison for the phase equilibrium, and the minor elements distribution between the NilS2-FeS matte with either FeOx-CaO or FeOx-Si02 base slag was investigated. The main results are summarized as: no difference in the nickel losses between both slags was found at high nickel content in the matte, and the fractional distribution analysis for arsenic and antimony pointed out their preferential fixation in the calcium ferrite slag rather than in the iron silicate slag. Considering the energy and pollution issues, the technical feasibility of using calcium ferrite slag in a converting process of the Bessemer matte will have a prominent future for the nickel industry.

Jan 1, 2003

By Hector Henao

To provide thermodynamic data for converting the nickel matte to liquid nickel, an experimental study was conducted in the phase equilibrium between the Ni-S alloy and the CaO-Ah03 based slag melted in a MgO crucible at 1873 K under controlled Pso2 of 10.1 kPa and pO;, in a range between 2.5x,IO,2 and 10.1 Pa by using CO-C02-S0Z gas mixtures. The content of nickel in the slag at POz of 10.1 Pa, above which solid NiO is expected to precipitate in the equilibrium state, was found to be 4.1 mass% and the contents of sulfur and oxygen in the nickel melt were 0.4 and 0.2 mass%, respectively. It was clarified that increase in the temperature reduces the solubility of nickel in the slag and the contents of sulfur and oxygen in the alloy. The distribution of minor elements such as gold, silver, copper, cobalt, iron, arsenic and antimony between the Ni-S alloy and the CaO-AI20) based slag was also studied. The distribution ratios of iron and cobalt, defined by (%X in slag)/[%X in alloy] where X is the minor element, are larger values than that of nickel, while those of copper, silver and antimony are similar to that of nickel. The distribution ratios of arsenic and gold are lower than that of nickel in the higher range of oxygen partial' pressure.

Jan 1, 2003

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to simulate nickel flash smelting process. In the nickel flash furnace, oxidation of concentrate occurs at one end, and reduction of slag occurs at the other. The model makes use two zones, namely the reaction shaft/settler zone and the appendage zone and accounts for 6 phases (matte, slag, silica, magnetite, Cu-Ni alloy and gaseous phase), 13 elements (Ni, Co, Cu, Fe, S, 0, N, C, H, Si, Al, Mg and Ca) and 33 chemical components in nickel flash smelting system. The compositions of matte, slag and gaseous phases in equilibrium are calculated by using the data of free energies of formation and activity coefficients of components. Two nickel sulfide species are used to allow for the modeling of sulfur-deficient mattes. The model predictions are compared with the known industrail data from Kalgoorlie Nickel Smelter, and excellent agreement is obtained. The model can be a very useful tool for monitoring and optimizing the actual industrial operations of nickel smelting process. The distribution behaviors of Ni, Co, Cu, Fe, S and 0 in the nickel smelting furnace depend on the process parameters such as smelting temperature, volumes of air, the content of the elements~ charge and oil.1. IntroductionThe nickel flash smelting furnace essentially consists of a reaction shaft where nickel sulfide concentrate is partially oxidized with air, a settle zone where matte and slag are allowed to separate, and a slag cleaning end where coke is added to provide for the reduction of the oxidized nickel from slag, and electrodes are used to provide heat.The theoretical model to consider a mass balance for copper flash furnace is developed by S. Goto and R. Shimpo[1][2J. However, this can not be true for nickel flash furnace as a whole since oxidation of concentrate occurs at one end (in the reaction shaft/settler), and reduction of slag occurs at the other (in the appendage). Despite these limitations, an acceptable pseudo-thermodynamic description of the furnace can be achieved using essentially two zones, namely the reaction shaft/settler zone and the appendage zone. Compositions of gas, slag and matte in two zones are calculated."

Jan 1, 1998

By H. Matsuda, T. Iwashita, H. Awata, H. Liwei, D. Hirabayashi, Y. Saito, S. Ozawa, Y. Goto

"The present study is concerned with investigating the effect of chemical treatment on enhancing the HCl absorption capacities of coal burnt ash and slag. It was found that the HCl absorption capacity of coal burnt ash discharged from fluidized bed combustor was improved by hydration with water and 5% polyethylene glycol solution. This phenomenon was based on an increase of the specific surface area of treated coal burnt ash. The HCl absorption capacity of hydrated ash with polyethylene glycol solution was almost equivalent to that of standard CaO and Ca(OH)2. In particular, the specific surface area of hydrated ash with polyethylene glycol solution was found to be 19 m2/g, which was more than over eight times larger than that of raw sample. Hydrated slag treated with lON sodium hydroxide solution also showed high HCl absorption capacity, with highly improved surface area. It was found that the absorption capacity of slag for HCl depended on the treatment time, showing the maximum absorption capacity for 12 hours of hydration treatment.IntroductionA large amount of coal burnt ash, slag and dust are discharged from such industrial processes as coal combustion and metal refinery etc., and it becomes an serious problem to recover and diminish these solid wastes because of the shortage of dump sites and subsequent metal elution to the environment. Figure 1 shows the present situation of reutilization of coal burnt ash and slag in Japan [1,2]. It is shown in this figure that these solid wastes are recycled as materials in the fields of earthwork, agriculture and forestry etc. A part of these solid wastes, however, is still dumped to landfill. To decrease this dumped amount, the development of environmentally friendly reutilization technique for these solid wastes is of great importance."

Jan 1, 2000

By Peter Bates

"HIsmelt has faced and overcome many challenges in the understanding and development of injection technologies that satisfy process and engineering requirements for further scale up to a commercial plant.An overview of the design basis of bottom and top injection systems with plant results are described in this paper.IntroductionAn appropriate way to introduce this paper is to initially reflect on the genesis of the HIsmelt Process.It is appropriate that Professor Womer is the one we are honouring as it can be claimed that by the involvement of CRA in the WORCRA process that the concepts for irijection systems in iron and steel pyrometallurgical processes achieved significant attention by the company. The development of water cooled injection lances and their application injecting solids and gases with success was certainly a pre-cursor to the development of other injection systems commonly used today in arc furnaces and for top injection at HIsmelt.HistOrically it was the work of Savard and Lee in Canada with shrouded tuyeres and the subsequent commercialisation of this technology at the Maxhiitte Steelworks spawning the suite of bottom oxygen blown process as known as QBOP; OBM and the subsequent combined blowing process such as KOBM that first commercially succeeded in injecting solids under a molten metal bath. The next progressive step from the injection of calcined lime in the technology development was the injection of coal for coal gasification as developed by Klöckner technologies being called KG, KSG and KMS and also the injection of coal for increased scrap melting.A paradigm shift in thought process to leap from steelmaking and coal gasification to direct smelting by injecting coal and iron ore into a molten metal bath in the correct stoichiometric ratio to maintain the bath at a constant temperature and carbon level was the true genesis .of HIsmelt.A good overview of the state of the art of tuyere type injection technology is given in Ref. 1."

Jan 1, 1996

By J. L. Johnson

The U.S. Department of the Interior, Bureau of Mines, investigated recovery of concentrates containing tin, tantalum, and niobium from the Kougarok deposit on the Seward Peninsula, AK. To date, 25 million lb of tin has been delineated in occurrences containing 0.36 to 1.32 pct Sn, and the resource potential is estimated to be as high as 25 million short tons at average grades of 0.75 pct Sn, 0.025 pct Ta, and 0,025 pct Nb. Deslimed ore was concentrated to 54 pct Sn, 0.3 pct Ta, and 0.3 pct Nb, with recoveries of 74 pct Sn and 44 pct Ta/Nb using a Humphrey's* spiral followed by a Deister shaking table. Tin values in the slimes were upgraded to a 5-pct-Sn concentrate using a Bartles-Mozley separator followed by flotation. The 5- pct-Sn was further upgraded by fuming to give a concentrate containing approximately 60 pct Sn. The recovery of the two products combined was 80 pct Sn and 46 pct Ta/Nb, A flowsheet with mill-design parameters resulted from the metallurgical testing. An economic analysis was made based on the proposed process.

Jan 1, 1990

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters. However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty. Ltd. in Australia.

Jan 1, 2003

By Emmanuel N. Zevgolis

After the Krupp-Renn process was shown to be unsuitable for treatment of the Greek nickeliferous laterites, the LM process was developed. It involved roasting reduction up to metallic iron in a Rotary Kiln (R/K) and smelting in an Electric Furnace (E/F). Ferronickel (with 15% Ni) produced in the E/F, was upgraded to 90-95% Ni in an 02 converter. Raw Ni was then electrolyzed to pure Ni. The LM process was not applied for very long however, due to various problems. So, the Larco process was developed, i.e., pre-reduction in R/Ks, smelting of the calcine in E/Fs for ferronickel production (15% Ni) and enrichment to 20% Ni, in an O2 converter. Until now, many technological improvements have been invented and applied or adjusted to the process, which have made it a fully reliable and competitive one. sohe of the improvements were the invention and application of a new granulation process for liquid ferronickel, the modification of the existing R/Ks, E/Fs and converters and the design of new ones, and others that are described in the paper. Keywords: Ferronickel, metallurgy, laterites, LM process, Larco process

Jan 1, 2004

By S. Ozbilen, B. Erdogan, M. Erdogan

To study by thermal analyses the response of precipitation hardenable alloys of Al-Cu-Mg and Al-Li-Cu-Mg system to natural and artificial ageing, a series of ternary and quaternary Al-alloys with nominal compositions of Al-l.13wt%Cu-0:65wt%Mg (alloy-I), Al-1.15wt%Cu-0.57wt%Mg-0.07wt%Li (alloy-2), Al-l.19wt%Cu-0.56wt%Mg-0.75wt%Li (alloy-3), Al-2.0lwt%Cu-0.89wt%Mg (alloy-4), Al-2.14wt%Cu"0.56wt%Mg-0.07wt%Li (alloy-5) were used in the present investigation. Samples in the form of rolled sheets are subjected to water quenching at 25EC after solution treatment at 530EC for 20 min. Alloys were aged naturally at room temperature (25EC) up to 2 months and artificially at 190EC up to 2 days. By using differential scanning calorimetry (DSC) in the temperature range of25-300EC, differential thermal analysis (DTA) in the temperature range of25-600EC together with Vicker's hardness measurements, the response to natural and artificial ageing of the alloys used in the present study were investigated. It was observed that in these alloys, GPB(Cu, Mg) zones [Guinier-Preston zones with Cu and Mg] do form during water quenching at 20EC following solutionizing heat treatment. Natural ageing of the same alloys causes formation of more GPB(Cu, Mg) zones, which results in hardening in the alloys. Artificial ageing at 190EC up to l day results in GPB zone dissolution causing preliminary decrease in hardness values while two days of artificial ageing in the alloys cause S' (Al2CuMg) precipitation confirmed by DSC/DTA analyses resulting in an increase in hardness values. Li addition up to 0.75wt% helps T1 (Al2CuLi) and T 2 (Al6CuLi3) phase formation together with S' precipitation as DSC/DTA analyses show after the same heat treatment.

Jan 1, 1998

By M. Ide, K. Takemura, S. Taenaka, K. Shinzawa

"The laser characteristic is strongry dependent upon the stoichometry of forsterite (Mg2Si04) and YSO (Y2Si05) single crystals, because of change in the valency and occupied sites of doped Cr in the lattice so that mole ratios of Mg0/Si02 and Y203/Si02 in the above single crystals must be precisely analyzed. In this study ICP-AES was applied for analyzing the mole ratios. Emission intensities corresponding to Si and Mg or Si and Y were measured at the same time with internal standard method. Preparation of sample solutions, measurement conditions of ICP-AES and interferences by coexisting components were discussed, resulting in excellently precise detennination of stoichometry of the above single crystals.IntroductionIn conventional stoichiometric analysis of single crystals, the stoichiometry is detennined by analyzing each component separately with titrimetry and gravimetry techniques. On the other hand, by stoichiometric analyses using ICP-AES, emission intensities corresponding to components are measured at the same time with internal standard method. Consequently erros caused by variation of analytical condition are canceled out.Cr-doped Mg2Si04 and Y2Si05 syngle crystals are known as laser materials. The change of valency and occupied sites of doped Cr affect the characteristic of single crystal as aleser materials. The change of state of doped Cr.Stoichometric composition of Mg2Si04 is constructed by 2mole of MgO and 1mole of Si02, and Y2Si05 is constructed by 1mole of Y203 and 1mole of Si02. In this study, required analytical precision in component mole ratio is within an error of 0.0010 for Mg2Si04 (CV=0.05wt%), and within an error of 0.0030 for Y2Si05 (CV=0.05wt%) (Table I )."

Jan 1, 1998

By Jian Li, P. Liu, R. Zhang and J. Lo

In the past decades, focused ion beam (FIB) has evolved into a powerful microscope that provides capabilities that no other microscopes can offer. The combination of high-resolution imaging and stress-free ion beam cross sectioning provides valuable microstructure information both at the specimen surface and beneath. FIB techniques are also the preferred method to prepare site-specific transmission electron microscope (TEM) specimens. CanmetMATERIALS owns a world-class microscopy facility, where advanced microscopy work provides strong supports to research programs that cover a wide range of subject areas. This paper is aimed to provide a few practical examples of FIB applications in microstructure characterizations that include cross-sectioning and imaging, serial sectioning, and advanced TEM specimen preparation in materials research at CanmetMATERIALS.

Jan 1, 2015

By Suchun Zhang

The alkaline oxidation of refractory gold concentrates containing arsenopyrite and pyrite at ambient temperatures and pressures has been found to be accompanied by the simultaneous dissolution of gold without the addition of cyanide. A detailed study has been made of the kinetics of the oxidation of the pure minerals and of several concentrates. The reaction products of the oxidation of arsenic and sulphur have been monitored using chromatographic techniques. In the case of arsenopyrite, thiosulfate, monothioarsenate, arsenate and sulfite are the principal products while thiosulfate has been confirmed to be the dominant product of pyrite oxidation. Gold, either as added powder or as a constituent of the concentrates has been found to dissolve simultaneously during the alkaline oxidation of both arsenopyrite and pyrite, and this appears to be associated with the in-situ formation of thiosulfate as a lixiviant. The effects of temperature, stirring speed, oxygen partial pressure, alkalinity and pulp density on the oxidation of arsenopyrite and the dissolution of gold have also been investigated. Keywords: Gold, dissolution, arsenopyrite, pyrite, alkaline, oxidation, thiosulfate, thioarsenate

Jan 1, 2005

By T. Ahokainen, J. Pitkälä, J. L. Xia, A. Jokilaakso, J. Vaamo

"The aim of the present paper is to use the two CFD codes to model the two phase flow in a water model ladle with central gas injection. The codes examined are CFX and Phoenics. An Eulerian two phase model is used and predictions are compared against the experimental data available. The results show that the codes can reasonably well predict the gas-liquid plume in the ladle, and predictions are generally in a good agreement with experimental data. However, differences do exist in predicting the gas volume fraction and velocity profiles. The results should be interpreted most carefully and cautiously, because they are very sensitive to the boundary conditions and dependent on the models for the physical phenomena involved. IntroductionSubmerged gas injection has widely been used in the metallurgical industry for more than a century. At the present, the use of gas is most effective in steelmaking industry where the advantages of the gas injection have already been long well understood. Effective mixing, large contact area between reactants, easy modifications and flexibility of the processes are the most important advantages. Disadvantages include refractory wear, blocking in the tuyeres, and splashing. These disadvantages can be reduced and advantages further improved by studying the flow phenomenon in process vessels. However, it is difficult to study flow in a real vessel because of the high temperatures and physical and mathematical modelling is therefore increasingly used in the process development work."

Jan 1, 1999

By Keiji Okumura, Jiayi Shan, Jian Yang, Masamichi Sano

"A new method of deoxidation and desulfurization of molten iron with magnesium vapor has been developed. An immersion tube, which was filled with pellets of the mixture of magnesia and carbon powders, was put into the molten iron. Magnesium vapor produced by carbothermic reduction of magnesia inside the tube was injected directly into the molten iron with argon carrier gas. The effects of temperature and carrier gas flow rate on deoxidation and desulfurization were investigated. A mathematical model of the reactions was developed. The rates of deoxidation and desulfurization were controlled by mass transfers of magnesium vapor in the gas-phase and oxygen and sulfur in the liquid-phase. This method may offer high efficiency for magnesium deoxidation and desulfurization of molten iron.IntroductionMagnesium is a strong refining agent in steel-making processes1 • At steelmaking temperatures, magnesium has a very low solubility in liquid iron, and a very high vapour pressure2 • Deoxidation and desulfurization with magnesium take place essentially through the interaction of magnesium vapor with oxygen and sulfur dissolved in molten iron, and magnesium can change chemical composition of nonmetallic inclusions3 • However, addition of magnesium to the steel bath is dangerous and does not give high efficiency in the refining process4 • Furthermore, as a refining agent, the price of magnesium is higher than aluminium and CaO fluxes. In the present study, a new method of the deoxidation and desulfurization of molten iron was developed using magnesium vapour in-situ produced by carbothermic reduction of magnesium oxide. Pellets made of mixture of magnesia and carbon powders were charged into an immersion tube, which was made of alumina or graphite. The magnesium vapor was injected directly into the melt. The effects of pellet mass, experimental temperature and carrier gas flow rate were studied on the refining rate. A mathematical model of the refining reaction was proposed on the basis of the experimental results."

Jan 1, 2000

By Hector Carreon

This paper presents experimental data for the magnetic field produced by thermoelectric currents around uncracked hard-alpha inclusions in a Ti?6Al?4V specimen under external thermal excitation for different nitrogen content ranging from 1.6% to 5.9%. According to our preliminary results, the magnetic flux density measurements were found to be rather sensitive to changes in nitrogen content with the exception of the intrinsic material background magnetic signal that affected deeply the detectability of inclusions and imperfections in non-contacting thermoelectric measurements. Hopefully, these preliminary results can help identify a non-destructive test method that can detect material inclusions with a level of nitrogen that could be detrimental to Ti?6Al?4V alloy components.

Jan 1, 2009

By Masami Taguchi

"It is found that lead monoxide, PbO, has an ionic conductivity, and the all solid-state electrochemical cell using this oxide as an electrolyte has attracted the attention of battery researchers. In this study, thin film PbO2/PbO/Pb solid cells were produced on glass substrates and their discharge properties were investigated. The acti.ve material for the positive electrode, PbO2, was obtained by reactive sputtering of a Pb target in oxygen plasma. The PbO electrolyte and the active material for the negative electrode, Pb, were vacuum evaporated from /3 -PbO powder and a Pb block, respectively. The open-circuit voltage of the cell agreed with the theoretical value based on the thermodynamic data, and the close-circuit voltage was improved by the addition of a univalent impurity such as sodium or potassium to the PbO electrolyte. The connection of the cells in series and in parallel produced a higher electromotive force and a larger capacity. Also, the charge-discharge cycling test revealed that the cell could be charged and function as a storage battery.IntroductionGenerally, the ionic conductivity of a solid-state electrolyte is lower than that of a liquid electrolyte near room temperature. This has been a serious obstacle to using such electrolytes in an electrochemical cell. However, some solid-state electrolytes, which can preferentially pass a specified ion and have high ionic conductivity, have been found. Lead monoxide, PbO, which is an oxygen ion conductor, is such an example (1)(2). If a solid-state electrolyte is adopted for use in an electrochemical cell the problem associated with a liquid electrolyte such as leakage can be alleviated. The cell structure also can be simplified, because the electrolyte plays the role of separator to prevent the active materials from mixing. Thus, physical vapor deposition technology may make it possible to develop a very thin film cell, which consists of only solid phases (3)(4). In this study, the thin film PbO2/PbO/Pb solid cell with a thickness· of only a few micrometers, in which all the constituents were systematically deposited on a glass substrate by reactive sputtering and vacuum evaporation, has been produced and the charge-discharge properties were investigated. An attempt was made to improve the discharge properties by doping impurities such as Na2CO3 and Sb2O3 into the PbO electrolyte. Moreover, the connection of the cells in series and in parallel to get a higher electromotive force and a larger capacity, and the charge-discharge cycling test to determine its use as a storage battery were carried out."

Jan 1, 2000

By Gabriel Riveros

The stags from the Teniente Converter (TC) have high copper and magnetite contents. The reduction and copper impoverishment of these slags in an electric furnace was simulated in the laboratory, as part of a conceptual study for the Ventanas smelter of ENAMI. The effect of power input, electrode immersion, temperature of the slag, coke and solid revert additions on the rate of magnetite reduction and copper recovery was investigated. It was found that the addition of solid reverts, containing copper matte, enhanced the recovery of copper. Magnetite stratification and a corresponding gradient of the copper content occurred in the slag. Microscopic examination of slag samples showed the presence of copper in the form of matte and metallic copper inclusions. The results of the experimental work combined with an analysis of the phenomena that take place in an electric furnace led to a better understanding of the slag cleaning mechanism. The successful start-up of the slag cleaning electric furnace at the Ventanas smelter resulted in good copper recovery and confirmed the beneficial effect of solid reverts addition. Electrode consumption is lower than anticipated. No bottom build-up problems have been experienced. Keywords: copper, slag, magnetite.

Jan 1, 2001

By Marco Olper

The Italian company Engitec Impianti has developed a new electrochemical technology for the treatment of Electric Arc Furnace (EAF) flue dust generated in steel mini-mills. This process is based on a new and completely different concept from the Waeltz technology applied at present and allows, due to its modular nature, for an erection on the steel producer's site. Engitec Impianti spent US $700.000 constructing a 500 t/y throughput pilot plant at Pittini Group's Ferriere Nord mini-mill in Osoppo, Italy in order to demonstrate the process capabilities and obtain the data for a commercial plant design. The paper describes the pilot plant performances and the engineering criteria for a commercial unit of 10.000 t/y throughput. The feasibility study demonstrates a pay-back period of 3 - 4 years for the commercial plant.

Jan 1, 1995

By I. Gaballah

Decontamination of synthetic solutions of copper acetate, chloride, nitrate and sulfate containing 10, 100 and 1000 ppm of copper, using chemically treated barks has been studied. Metal percent removal from solutions depends on the pH and the initial concentration and to some extent on the salt used. It varies from 40 to 99 % of the solution initial metallic ion's content. The maximum retention capacity of the treated bark varies from 31 to 43 mg of Cu per gram of dry modified bark. Bark loaded with copper had been analysed by Scanning Electron Microscopy and lnfra Red spectroscopy. Cu is uniformally distributed in the bulk of the bark. No copper segregation is observed. It seems that copper is bound to the acidic sites of the bark. Anions are not detected on the copper loaded bark neither with the SEM or with the IR spectroscopy.

Jan 1, 1993