Search Documents

By Zhi-xiang Cui

Effects of flux, vulcanizing agent and reductant on slag cleaning in new-type slag cleaning furnace (Φ3.6 × 8.1 m) were investigated under the conditions including smelting temperature of 1200 and 1250 °C, settling time of 30 and 60 min, and Fe/SiO2 of 1.7–1.9. The results show that addition of SiO2, B2O3 or CaF2 into original copper smelting slag can improve settling separation effect. Though no effect on copper recovery, addition of FeS can provide heat required by reaction with oxygen and reduce copper dissolution in spinel phase and slag. Copper content in discarded slag can be controlled at 0.26% under the optimum comprehensive conditions with ratio of oxygen to natural gas of 1.6.

By E. J. Peuraniemi

Oxidation of chalcopyrite concentrate and two low-iron copper mattes were studied using a laboratory scale laminar-flow furnace simulating the phenomena taking place in different zones of the reaction shaft of a flash smelting furnace. In the experiments, screened fractions were fed into the furnace and sampled after short reaction time intervals by quenching them into a water film. Experimental conditions included temperatures of 1100 and 1300°C with reaction gas oxygen contents from 21 to 75 vol.%. Samples were analysed chemically for Cu, Fe and S to define removal rate of sulphur. Optical and scanning electron microscopy with EDS-analyser were used to examine the samples. In this paper, oxidation kinetics as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are viewed to closely define the proceeding of the oxidation, and, consequently, to compose a detailed model of dust formation and reaction mechanisms. Data obtained in the experiments broadens the knowledge of physical and chemical phenomena in flash reactions and serves as reference for computer simulations.

Jan 1, 2000

By Herbert Pöllmann

Waste disposals are needed for safe deposition of different kinds of materials which can not be used as secondary raw materials. Often high contents of heavy metals must be bonded tightly to cristalline compounds to protect the environment from contamination. Therefore it is important. to find minerals which are capable to incorporate different heavy metals and protect the ground water. The power of resistance against leaching out effects of highly water-soluble salts can be increased. Mineral groups of metal hydroxy salts, ettringites, apatites, sodalites and calciumchlorosilicates and their hydrates are recommended for their formation in mineral reservoirs. Different wastes as red mud, gasification ash, garbage combustion ash and fluidized bed ashes were included in this study. The formation of different new compounds and their properties were determined.

Jan 1, 1991

By Hong-ying Xia, Bao-bao Wang, Jin-hui Peng, Bing-guo Liu, Li-bo Zhang, Zhi-qiang Li

Based on optimization using response surface methodology designed by Box- Behnken, to study the interaction of wet industrial salt with moisture drying temperature (50-90 ); duration (10-50s); and the weight of the materials (20-60g). The results show that: the experimental parameter conforms to the quadratic equation model to influence the moisture content and the dehydration speed., in analyzing the significance and the interaction of various factors, the optimum by the Design Expert software conditions for drying with microwave radiation include temperature of 90 , duration of 10s, and sample mass of 26g. Verified by experiment, the moisture content after drying is less than 0.25% and the dehydration rate reached 1.37g/min, between the predicted value and the actual value confirmed good fitting degree.

Jan 1, 2015

By A. E. M. Warner

Inco Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By Seetharama C. Deevi, Mohammad R. Hajaligol, Sarojini Deevi

"Carbides and nitrides of iron are being considered as magnetic materials for high-density recording due to their chemical stability and high-saturation magnetization values (> 100 emu/g). Iron carbides and iron nitrides with magnetic properties suitable for magnetic media were synthesized by employing a novel synthesis procedure based on fluidization of powders in reactive atmospheres. Fluidized-bed reactors of laboratory, bench, and pilot scale were employed for the synthesis of iron carbide, FeSC2, by reducing and carburizing U-Fe203 in the temperature range of 300 to 550 ºC. A temperature of 400· ºC and a reaction time of 2 to 3 h are found to be optimal for the synthesis of iron carbide. When the carburization was carried out in a reducing and carburizing atmosphere such as carbon monoxide, nucleation and growth of FeSC2 occurred directly from Fe304 with no intermediate phases such as FeO or Fe. Longer carburization times resulted in the deposition of carbon on the surfaces of FeSC2 particles due to Boudouard reaction, and higher temperatures favored the formation of a mixture of carbides such as FesC2 and Fe3C. Iron nitrides were synthesized by reducing u-Fe203 in the temperature range of 350 to 550 ºC, followed by nitriding in the temperature range of 350 to 550·ºC. The powders were characterized using X-ray diffraction, scanning electron microscopy, thermogravimetric analyzer, and a vibrating sample magnetometer.IntroductionRecent demand for high-quality recording of optical, electrical, and audio signals generated interest in magnetic tapes with high-recording densities as compared to the conventional magnetic tapes based on U-Fe203. At present, commercially available magnetic tapes contain maghematite, U-Fe203, as a magnetic material with a saturation magnetization of90 emu/g and a coercive force of 400 Oe. Recording of signals at a higher density per unit volume of magnetic material demands magnetic materials with high-saturation magnetization and a reasonable coercive force. Although metallic iron particles possess a saturation magnetization of 130 to 150 emu/g and a high coercive force of 1000 Oe, the gradual oxidation of iron-to-iron oxides (of lower saturation magnetization) prevents the use of iron particles for high-density recording. In contrast, iron carbides such as FesC2, Fe7C3 and iron nitrides such as Fe4N and Fe3N possess excellent magnetic properties coupled with good electrical conductivities and high hardness. The carbides and nitrides of iron have generated significant interest as magnetic materials for the next generation of magnetic tapes due to their unique magnetic properties and relatively greater oxidation resistance as compared to metallic iron particles [1-4]."

Jan 1, 1994

By Chikabumi Yamauchi

The comprehensive scientific development of conventional industrial technologies stimulates the creation of new ones in the next generation. Prof. Akira Yazawa has just accomplished such an important work in the non-ferrous pyrometallurgical field. The results of his successful research are immortal. The research group of the author has conducted since 1985 fundamental studies on the application of sodium carbonate slag to copper fire refining. In the present paper, a calculation method for the distribution ratios of impurity elements between sodium carbonate slag and molten copper will be shown. The specific treatment by sodium carbonate slag will also be presented as an effective way for reducing each impurity content in the molten copper to 0.1 mass ppm, which is the level required for the production of high purity copper. The thinking-out of this evaluation method gets a hint from the Equation (2) in the text which was proposed by Prof. Akira Yazawa.

Jan 1, 2003

By L. I. C. Fernandez, E. B. Ferreira Filho, L. G. Pedroti, L. G. Justino, W. E. H. Fernandes, R. C. S. S. Alvarenga

More and more industries have been concerned with the disposal of the wastes generated in their production processes, once this generates a positive impact, both visual and economic enterprise, no more needing to have resources for transport and final disposal of wastes. In this context, and seen the importance of the Portland cement a sa building material, which aims the creation of an ecological cement from the mix of two wastes, the grits, which is a waste generated in pulp production, and the granite beneficiation waste. It proceeded initially with the chemical and physical descriptions of the wastes. Five mixtures, varying the percentages of the wastes and the preparation method of the raw materials, were prepared. After,the blends were sintered in a muffle furnace at 1300 °C for 15 min, forming new compounds that were compared with national cements, according to the Brazilian technical standards. It was concluded that the sintering of the product obtained satisfactory results, presenting good binder characteristics, however, some parameters were outside the limits for common Portland cements such as rapid setting time, large expandability and low compressive strength.

Mar 1, 2017

By E. Oshilna

The Mitsubishi process has many advantages pertaining to economical and environmental matters. These advantages have led to the installations of the Mitsubishi process in constructing new smelters: The Mitsubishi process utilizes highly oxygen enriched blast air and uses a special lime slag in the C?furnace. These characteristics change the . distribution of Impurities from other processes which use P.S. converters, Recently an Increased amount of secondary materials which contain impurities Is being treated at Naoshima Smelter. In order to cope with an Increment of the Impurities load and maintain the cathode quality, many Improvements have been Implemented. This paper discusses the impurities behavior In the Mitsubishi process and describes the measures taken to treat an Increased ?amount of secondary materials:

Jan 1, 1998

By Zhihua Wang

Through metallurgical calculation and process analysis based on metallurgical theory, it is aimed to raise the concentration of smelting oxygen and improve the update speed of reaction interface, accelerate the reaction and achieve a high-intensity smelting at the stage of converting. The PM plant has launched a theoretical research on model of high-intensity converting aiming at increasing the oxygen concentration of converting, carried out transformation of Kaldo furnace converting system, performed a series of industrial trial operations, conducted multiple rounds of tracking test and data comparison in reducing the furnace cycle, lowering the unit consumption of fuel and stabilizing the furnace lining life. The move has practically tested and verified the correctness of high-intensity smelting theory.

By Barry J. Welch

The production of primary aluminium can potentially lead to metal that, with minimum treatment, meets a high purity standard. Smelters that can achieve a significant proportion of their production in this manner have a competitive edge which is of growing importance as the use grows for such items as compact discs and the like. Superimposed on the desire to produce high quality metal are stringent environmental requirements that the industry must adhere to. The environmental 'legislation focuses on fluoride emissions and the approach adopted is towards a zero waste management philosophy. The fluoride recycling process does, however, result in volatile impurities being captured and recycled to the cell. Aluminium has an extremely high reduction potential and this results in a significant proportion of the recycled impurities being reduced at the electrolyte metal interface and thus contaminating the metal. This paper reviews sources of impurities and the impact of the operating procedures adopted on metal treatment.

Jan 1, 1996

By Mototsugu Matsuno

A new process has been developed to treat fly ash generated from municipal incinerators, which contains not only toxic metals such as lead and cadmium, but also dioxins. The process includes the following steps; fly ash is formed into green pellets with some additives and the pellets are then roasted to eliminate or stabilize the toxic metals and to decompose dioxins. A pilot plant with a capacity of approximately 100 kg/hr was used to test the process. The tests verified that heavy metals were either volatilized or stabilized and dioxins were decomposed by high-temperature roasting. The pelletized ash was found to be non-toxic, so that it can be recycled as artificial lightweight aggregate. It was also found that volatilized metals collected as secondary ash can be recycled as smelting resources.

Jan 1, 2003

By A. S. Usmani

The flow associated with the pouring of molten metal into moulds has been modelled on the basis of certain simplifying assumptions. A finite element based Navier-Stokes equation solver has been used to analyse the flow. The velocities obtained from the Navier-Stokes equation solver are used to advect a pseudo-concentration function for modelling the fluid front. A simple problem with a known analytical solution is solved first to test the model. Subsequently, several more examples with varied geometrical configurations are modelled, including one with curved flow boundaries.

Jan 1, 1992

By Hani Henein, J. Barry Wiskel

"The easy accessibility and power of the PC, as well as the education of our engineering students in the use of these tools, are compelling reasons for developing computer aided instructional (CAI) tools. There are a wide range of areas in the engineering curriculum where students must learn the steps and the process of applying judgement in problem solving. In the typical course instruction, · an instructor introduces theory to students; the application of the theory to solving problems is often demonstrated in the abstract. Students therefore spend a significant amount of time learning how to apply the theory to problem solving. Additional time and effort must then be spent to get students to the point of learning concepts and integrating this knowledge. A number of computer aided packages have therefore been developed for use in several courses in the materials science and engineering curriculum that encompass both calculational and instructional capabilities. This paper presents an overview of some of these packages which include the solution of a non-linear equation, the instruction of binary diffusion couples, an introduction of crystallography, an introduction to heat transfer and the solution of thermodynamic stability diagrams. The context in which these CAI Tutorials were developed and are being used will be discussed. The pitfalls in the development of these packages will also be discussed. The use of the tutorials has important implications on the expectations from an engineering education of both instructor and student.IntroductionTraditionally, it is quite routine to teach engineering students how to use a computer (the PC today for undergraduates) as a tool in performing engineering calculations or in simulating a process or a unit operation. This often takes the form of one course in computer programming, whether it is Fortran, Visual basic or a spreadsheet, and another course in numerical computation. However, the materials and electronic revolution have brought about considerable advances in computer power and speed, and accessibility. Today, the manipulation of digital images, movies, and speech are commonplace on a desktop PC.' Many mathematical models that were executed only on workstations can now be readily handled on a PC. Concurrently, more of our students own a PC even if their curriculum does not require them to purchase one. Today, virtually every university student has been introduced to the PC in either their elementary or high school education. Hence, the increased capabilities and accessibility of the PC and the familiarity of students with this tool make it compelling to explore its use as an educational tool for our engineering students. This is not a traditional role of a computer in our engineering curriculum."

Jan 1, 2000

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, PSo, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of O2 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By S. V. Cherty

The utilization of natural gas in non-ferrous industries during smelting and refining stages of copper , aluminum, zinc and lead was studied. The total amount of nonelectrical energy consumed in the production of zinc, copper, lead and aluminium, are 96.5% ,93%,92%, and 6 % respectively. It is calculated that 9.45 wt %of air of stoichiometric amount can be substituted by natural gas to the total air input in the nonelectrical energy utilization processes. The results showed that the non electrical energy may be substituted to an amount of 71 % ,52 % ,35 % ,32 % ,and 26% ,in the production of lead, aluminium (plates, foils) copper, aluminium, zinc, respectivelly. Similar calculations are carried out in terms of energy in Btu for the total production of non-ferrous metals in the U.S. It shows that 51.866~106 millions of Btu of nonelectrical energy can be substituted by 54.58~106 cu. ft of natural gas. Finally, the substitution of non electrical energy in terms of equivalent coal energy is discussed. 1t is shown that total non electrical energy is equal to 1.852 million tones of coal .If this 1.852 million tones of coal is replaced by natural gas, a total savings of 22.14 million dollars are achieved. The total or partial substitution of coal by the natural gas in the existing industrial processes and modification of redesigning the processes is discussed.

Jan 1, 1993

By Manjie Li, Mingrui Yang, Haijun Peng, Shuxing Qiu, Wei Liu, Shengfu Zhang

It is important to produce and utilize highly reactive coke in order to reduce the energy consumption and CO2 emissions through improving shaft efficiency in blast furnace. The present study aimed to investigate the transformation of iron minerals and properties of iron coke (the coke mixed iron ore fines). Along with the increase of iron ore fines, cold strength displayed a slight downtrend and the pore structure wasn’t inferred to be a major factor affected the properties of iron coke. During carbonization, the majority of mixed iron oxides were reduced to metallic iron by CO and H2 and the degree of metallization achieved to approximately 75%. Nevertheless, produced metallic iron was oxidized by pure CO2 during gasification. Iron coke reactivity index (ICRI) was obviously enhanced and the iron coke strength after reaction (ICSR) drastically decreases, which were also significantly influenced by crystal structure of carbon.

Jan 1, 2015

By Tuula Mäkinen

One of the latest applications of the Outokumpu Flash Smelting Technology is the direct smelting ,of nickel concentrates to metallised low-iron nickel mattes. Compared to the conventional nickel smelting, the new DON process needs a lower number of smelting vessels resulting in considerable economic and environmental benefits. Fundamentals of smelting nickel concentrates in one stage to low-iron mattes are presented. Properties of nickel. smelting slags with an emphasis of the slag fluidity at high MgO-levels are also discussed. Conditions prevailing in DON mattes at high oxidation degrees are presented as well as their influence on the behaviour of such mattes in the settler and on tapping the furnace. Distributions of elements in the direct smelting are presented and compared with the conventional process. A further comparison is made with pilot-plant data and the industrial scale.

Jan 1, 1998

By Esperidiana A. B. Moura, Elizabeth Carvalho L. Cardoso, Glauson Aparecido F. Machado, René R. Oliveira

Plastics global annual production exceeds 250 million tons and more than 40% of the total plastic production is used as packaging materials. In recent years polymeric materials derived from biomass have received great attention due to scarce petroleum resources and environmental concerns. PLA is one of the most extensively studied bio-based and bio-compostable aliphatic polyesters; nevertheless, high brittleness and low toughness limits its application. Blending PLA with PBAT (Poly(butylene adipate-co-terephthalate)), an aliphatic-aromatic copolyester, was the solution found due to its high toughness and biodegradability. Differences between PLA and PBAT solubility parameter values lead to the formation of immiscible blends as well as reduction in their mechanical performance besides a poor morphology; so, 5% of pre-irradiated PLA and a previous compatibilized PLA/PBAT (EcovioTM) were added to PLA/PBAT blends in order to improve miscibility phases. Investigations were accomplished on phase morphology (SEM), mechanical properties, thermal behavior and X-ray diffractions (XRD).

Mar 1, 2017

By Bogdan Petkovic, Boban Todorovic

In the early 90's a completely unknown problem was encountered at the converter Department: it was a chronic shortage of the cold copper charge needed for the second operating period. A high temperature operating regime was caused which further provoked a chain of consequences such as a drastic drop of the number of operations in campaigns. The consumption of repair bricks reached the quantity of 8.3955 kg / tonne of anode Cu. In 1994, we won the process of cold material smelting during the "copper" blowing [2]. The number of operations per campaign reached 180-200 again. Also in 1994 we won the process of smelting cold materials to obtain "tin" blowing with the purpose of completing their processing cycle [2]. During the period 1994 – 2007 a total of 107,845 tonnes of cold material were remelted to make copper and 56,794 tonnes were re-smelted to obtain "tin". Upon synthesizing these two processes, a completely new model was achieved in 2005, by Bogdan Petkovic, which entirely utilized all available energy of the Peirce-Smith (PS) converters of the Bor Copper Smelter and now represents the basis of the time cycle. The cold material now enters the converter plant, copper recovery is increased and the method itself is environmentally friendly. 167

Jan 1, 2009