Search Documents

By Andre Zingano

The objective of this paper is to compare the behaviors of different types of roof bolts: (1) One-Step Bolt (OSB), (2) Fully grouted Bolt (RB), (3) Combination Bolt (CB), and (4) Torque tension Bolt (TB). Two dimensional numerical models were built for both bolted and unbolted roofs. The geological sequence and rock properties used in the numerical models represent the typical roof condition for Pittsburgh coal seam. Using the unbolted roof as a base case, a comparison is conducted by monitoring the roof vertical displacement at the center of the entry and at the bolt positions, the axial force in the roof bolts, and stress distribution in the bolted area. The grout/rock interface is assumed to be perfect. The estimated roof displacements showed that the differences among the four types of roof bolts are small. The major differences are in the shear stress at the grout/rock contact and in the shear stress along the immediate roof bedding interface as well as in the bolt axial stress. There is less axial stress for the OSB compared to RB and CB as the diameter of the OSB is much bigger and the contact area between grout and rock is twice as large as for RB and CB. The higher strength of the OSB contributes to keep the bedding planes in the roof closed.

Jan 1, 2007

By John Feddock

A recent increase in energy demand has resulted in the rapid growth of coal consumption in the People?s Republic of China (PRC), which is the largest coal producer and consumer in the world. Reportedly, the safety issues in Chinese coal mines have been improving, but the number of fatalities and serious injuries continues to be alarmingly high. The number of fatalities from catastrophic accidents have prompted researchers to review the Chinese mine safety situation and to look for potential solutions. Marshall Miller & Associates, Inc. (MM&A), along with various collaborators, has investigated these issues as part of its work on various projects in the PRC and has discussed the concerns with relevant Chinese officials. Preliminary investigations by MM&A of coal mine accidents during 2001?2006 in the PRC indicate that 65%-78% of the total fatalities were the result of gas explosions and roof falls in underground mines. Even though the drainage of methane has been practiced for decades, current practices do not always produce satisfactory results due to technical constraints and equipment limitations. Based on prior experience of in-seam degasification at the Daning Coal Mine located in Shanxi province, MM&A believes that in-seam directional drilling technology can be a viable solution to degas the low-permeability Chinese coal deposits. This paper 1) reviews current Chinese coal mine safety conditions, 2) analyzes the advantages/disadvantages of current degasification practices in China, and 3) presents the pre-mining degasification practices for the longwall panel at the Daning Coal Mine.

Jan 1, 2007

By Axel Preusse

Mining subsidence plays an increasing important role in the Chinese hard coal mining. Reasons for this are a substantial rise of production during the last decade, a dense settlement in many mining regions, the increasing emergence of private residential property as well as a grown environmental awareness. German companies and research institutions hold an over more than 150 years existing know-how in all subjects of mining subsidence engineering. Due to partially comparable preconditions regarding mining depth, mining methods and geological conditions, a close co-operation between German and Chinese mining subsidence engineering experts has been in existence for some years. This German-chinese co-operation is introduced in this paper.

Jan 1, 2007

By Krzysztof Kotwica

The steady demand for rock materials leads not only to on increase in mining but to the need for decreasing the loss of material in the process of exploitation as well. It brings about an increase in using of explosives in open pits and as a result an increase of after blasting gases volume, vibrations, the scattering (dispersion) of stone ect. All these factors affecting the environment lead to the research work for applying the electrohydrodynamic methods both in open casts and underground mines. In the article the authors describe the concept of this method and construction of equipment which recently have been successfully introduced in mining, the results obtained determine the possibilities of using this method and the future directions. The results of combined method with high-pressure water jets cutting and prototype equipment for separating rock blocks from the rock mass using special head with high-pressure water jets are also described.

Jan 1, 2006

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By Srinivasulu Tadisetty

The productivity and safety of Indian longwall operations are insignificant because of complex geomechanical conditions. Therefore, the continuous monitoring and forecasting of abnormalities is imperative. Authors developed an innovative real time system and implemented in one of the Indian longwall mines. The real time system was successfully acquired data from underground chock shields and classified the behaviour in real time as per the standard norms. Furthermore, it forecasted the abnormal behaviour of chock shields promptly. The management was implemented appropriate precautionary measures based on real time forecast. Subsequently, the longwall operations were successfully completed with enhanced productivity and safety. This paper discuss the impact of the innovative system on productivity of experimental longwall mine.

Jan 1, 2006

By Brijes Mishra

This paper presents a correlation of acoustic emission (A.E.) with physical and mechanical properties of different types of rock and coal specimens which were tested under aegis of a consultancy project from a Columbian Mining Company. In this study, three types of rocks which are sandstone (Arneisca), siltstone (Arciolita) and claystone (Limolita) and two different types of coal were tested. The tests were carried out under constant loading rates according to ASTM Standards for determining Young?s Modulus and Poisson?s Ratio. In both cases a MTS electro-hydraulic loading system was used. Mode of failure in each material was characterized by the acoustic emission and the results were substantiated by the deformation characteristics of the materials during failure.

Jan 1, 2006

By Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: ? Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; ? Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

Jan 1, 2007

By Arun Kumar Singh

Wide variation in the nature of the coal seams and the surrounding rock mass of the Indian coalfields and very little information about the associated stress fields were observed to be the major hurdles in the straight forward application of a continuous miner (CM) based mechanised depillaring approach. Due to various techno-economic reasons, a considerably large number of coal seams have been developed and are standing on pillars in India. The development of pillars is done as per Indian coal mines regulation, which results in pillars of relatively large size. In fact, the large size of the pillars provides stiff natural support to control caving of the massive overlying strata. However, the size of these pillars is not conducive for the single pass pillar stripping technique and, therefore, there is a need for pillar splitting before pillar extraction/retreating. Splitting of the pillar may reduce the competency/stiffness of the pillar, which creates a chance of overriding during final extraction below a massive roof stratum. This paper first discusses the existing coal mining scenario in India followed by a brief presentation of geo-technical details of pillar extraction at the three sites where a CM has been introduced for depillaring/pillar retreating in the country to date. Based on past rock mechanics experiences with conventional depillaring faces, stability issues of the pillars, fenders, and stumps in and around the depillaring face are discussed. This may prove to be an important factor in the success of future CM faces. It is recognized that the application of the modern strata movement monitoring techniques may improve operation safety by providing valuable qualitative and quantitative information that can be used to improve the design of modern concepts like roof bolt based breaker line support during pillaring.

Jan 1, 2009

By Jan A. Nemcik

Steel mesh has been used successfully for many years to control friable roof conditions and prevent loose roof and rib material from caving into the roadway. Despite its extensive use, the installation of steel mesh is difficult to automate and many other products have been evaluated as an alternative for skin control. Ideally, the properties of these new products should be similar or better than those of the steel mesh. In particular, development of a strong and resistant shell that minimizes movement along the fractured rock and coal surfaces between the bolt anchors is recommended. A strong surface adhesion and the strength of a reinforced polymer skin can provide the necessary toughening mechanism required to enhance roadway surface support by forming a reinforced polymer/rock surface layer. Most of the Thin Spray-on Liners (TSL) evaluated in the mines are weak with slow curing times, and the plastic mesh currently used to support the coal ribs is relatively weak. Therefore, neither material can seriously compete with steel mesh. Currently, a new polymer product that cures in seconds and forms an instantaneous strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong.

Jan 1, 2009

By Yi Luo

The efforts to mitigate longwall subsidence influences on various residential and farming structures by many coal mining companies have been successful in the recent years (Luo, et al, 2003). The successes were largely dependent on the accurate subsidence predictions, correct assessments of potential influences, appropriate design and implementation of the mitigation measures. However, such efforts for protecting large industrial structures are still very rare. In this paper, the successful assessment and mitigation of the subsidence influences associated with a very intensive dynamic longwall subsidence process on a large workshop are presented.

Jan 1, 2005

One of the problems associated with the maintenance of roadways in underground coal mines is that of dealing with roadway closure. Sidewall weakening technique is based on the transference of the high stress zone further away from the vicinity of roadway. This transferral is carried out by weakening parts of sidewalls of roadway by cut- ting slot, drilling a series of parallel holes or blasting during development stage. In the paper, the effect of sidewall weakening on the stability of roadway is studied by finite element analysis and field experiment. The finite element analysis shows that sidewall weakening can control the development of yield zone around a roadway, improving the stability of roadway. It is also shown that if in- situ horizontal stress is lower or higher than the in-situ vertical stress, it is difficult to obtain roadway stability by sidewall weakening. The field experiment shows that roadway closure can be controlled by sidewall weakening with blasting.

Jan 1, 1990

By Yongjie Yang

Experimental study on the strength and deformation characteristics of coal under cyclic loading provides guidance for designing coal pillar which is subjected to repeated mining influence during mining. This paper studies the strength, deformation and fatigue process of No.3 coal from Xinhe Colliery under cyclic loading by the MTS815.03 servo-controlled rock mechanics test system. The results indicate that coal is more susceptible to fatigue damage than other hard rocks. Under uniaxial cyclic loading, the fatigue failure ?threshold value? of coal is smaller than 78% of its uniaxial strength, and there is also some fatigue damage when cyclic loading and unloading experiment is carried out below the fatigue failure ?threshold value?. Axial deformation can be divided into three stages: Initial deformation, steady-state deformation and accelerating deformation. Transverse deformation can be divided into two stages: Stable deformation and accelerating deformation. When the transverse deformation begins to increase rapidly and the deformation recovers only slightly upon unloading, it?s a precursor to failure of coal. Under cyclic loading, fatigue failure develops through a process of compaction, strain hardening, and strain softening.

Jan 1, 2006

By Ebrahim Ghasemi

Problem statement: One of the most challenging safety problems in room-and-pillar coalmines is controlling roof falls during retreat mining. Roof falls not only cause both fatal and non-fatal injuries to miners, stoppages in mining operations, and equipment breakdowns, but also results in the inefficient recovery of coal reserves. Approach: Sufficient awareness of effective parameters related to roof falls is an important factor in roof control. In this study, the major contributing parameters on roof falls during retreat mining are introduced based upon experience and judgment acquired from extensive retreat mining case histories and a review of relevant literature. Key findings: The main roof fall parameters in retreat mining can be divided into three categories: geological, design, and operational. Key conclusions: The design and operational parameters can be controlled by the engineer and/or operator. By the appropriate selection of these parameters in the design and implementation stages of retreat mining, the roof fall risk can be decreased to an acceptable extent.

Jan 1, 2012

By John Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has collected pillar and span data at 34 stone mines in 10 states to develop pillar and roof span design guidelines for underground stone mines. Pillar, floor and roof conditions each contribute significantly to the overall mine stability. The roof may be stable for a century, or it may appear to be stable but fail with little warning. Clearly, an assessment of the mine roof is critical to the safety of these operations. However, up until now, the assessment of the mine roof came primarily from exposures in roof falls or portal areas. This provides only limited information, and a more proactive approach is needed to assess changing mine conditions. A separate effort was undertaken to examine the roof structure with the use of a borescope. Numerous physical and geologic roof structures were observed with a stratascope/borehole video camera. The objective of this work was to develop a technique of assigning numerical values to features seen within the mine roof and apply those values to formulate a roof stability evaluation. Such features as changes in color, grain size, and general lithologies are readily observed. Minor structures in the rock, fossils and fractures are also readily identified. Each feature may have a variable and site-specific impact on roof quality. A number of mines were visited and a series of holes were borescoped in each mine. The features identified in the roof were classified and potential for roof damage related to each feature was assessed. A process is presented that relates the structures and their locations to provide a numerical value, or roof quality index that can be used to assess roof stability.

Jan 1, 2009

By Francis Kendorski

The Skyline #3 Mine of Canyon Fuel Company in Utah was planning longwall mine development adjacent to and downdip of older mine workings known to be flooded. Barrier pillar geometries and widths were proposed by mining company personnel. Hydraulic conductivity testing suggested that the general characteristics of the local coal seam, dikes, and faults are only weakly conductive and that leakage through the barriers, if any, would be minor. The mechanical performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods and (2) numerical stress modeling. Comparison of the proposed design, with the range of barrier widths derived from the empirical methods, served as a first-order check on the adequacy of the proposed design. Numerical modeling was used to evaluate conditions site-specific to the Skyline #3 Mine and barrier geometry. Models were developed to quantify the relationship between barrier width and the abutment stresses onto the future workings. The models were also used to estimate the stress distribution within the barrier pillars. The hydraulic performance of the proposed barrier pillar design was evaluated according to (1) published empirical design methods for hydraulic impoundments, (2) empirical method estimates of seepage through coal barrier pillars, (3) numerical hydrogeologic flow modeling, and (4) numerical strain modeling. Using the techniques described above, and based on relevant industry experience, underground observations, knowledge of local geologic conditions, hydrogeologic measurements, and analytical results, the level of geomechanical risk associated with the barrier design as proposed was considered low and the level of hydraulic risk was considered moderate. The largest uncertainty that remained was the possibility that unfavorable geologic structures, such as faults and dikes, would act as conduits for leakage of impounded water into the new workings. Although the study indicated only minor steady-state leakage would occur through a small number of known structures, the presence and full leakage potential of threatening structures in the barrier could not be reliably known until the barrier was mined. One longwall panel has been completed adjacent to the barrier with no evidence of water flow even in fractured zones. Thus, as predicted by the modeling and analysis, it appears that abutment stresses imparted on the barrier during mining did not substantially alter the natural hydrogeologic characteristics, or leakage potential, of the barrier. The longwall coal mine water-barrier pillar design and performance are considered a success.

Jan 1, 2007

By J. Brasfield

Jim Walter Resources, along with the Rock Mechanics Branch of British Coal and Strata Control Technology Pty. Ltd., is presently studying the yield-stable-yield pillar design in use at the Blue Creek No. 7 Mine located in Brookwood, Alabama. This paper describes the steps taken to determine stresses on the strata surrounding the pre-driven development entries. It also describes the installation and monitoring of stress cells and extensometers used to quantify the stress build-up and strata movement associated with the headgate pass of a longwall panel. The findings of this study will be used to design and predict the performance of a 2 entry yield pillar system in the Parkgate Seam at Welbeck Colliery in the United Kingdom. Stress measurements and strata movement data from No. 7 Mine and Welbeck will be used to develop a computer model that can predict the performance of such a pillar system in British mines. Jim Walter Resources will use this data to study the performance of the present yield-stable-yield pillar system in order to determine if conditions will allow the stable pillar width to be decreased while maintaining current standards of safety and production.

Jan 1, 1994

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012