Search Documents

By A Pettersson

LKAB owns and operates two of the largest underground mines in the world in Northern Sweden. In Malmberget, with a production capacity of about 30,000 t/day of iron ore, the current main 815 m haulage level is rapidly approaching the end of Its life and plans are being made for its replacement on the 1000 m level. Due to the separation of the orebodies, trucks have been chosen for transporting the ore from the orepasses to the crushers. The trucks currently in use have a capacity of 120 tons. To increase the efficiency of the loaded haul, the new main level will have a favorable slope from the drawpoint locations to the crushers. From the new level the crushed ore will be transported by conveyor to the 815 m level for hoisting to the surface. The paper discusses the planned mining and transportation system.

Jan 1, 1998

When I wrote the Railroad portion of "Mining Engineering" magazines 94 Powder River Basin (PRB) Coal Article I described to you some definite destinations the Railroads had in mind. As with many destinations, the ones I wrote of turned out to be merely stops on the way to places that we have yet to reach. Somewhere along the way we discovered that making it better is a continuous process not just something that you can do in phases I, II, III, & IV. We always knew this I suspect, but perhaps not at the awareness level that exists in RR environments in 1997. The purpose of this article is to update the 94 article, which I could do very quickly. Everything I told you we were going to do in 94 is done, end of story! But in addition to making it a very short article it would not be telling you the things RR has done beyond what we were planning in 94 and for the future.

Jan 1, 1998

By Yuting Xue, Todd Minoski, Daniel Su, Mark Van Dyke, Mark Mazzella, Steve Hicks, Zoheir Khademian, Nicole Evanek

Design of chain pillars in a longwall mine setting is one of the main engineering controls on the global and local stability of the mine. Challenges with roof instabilities, floor heaves, and pillar failures can be alleviated, to some extent, by careful design of gateroad configurations and chain pillars. This work investigates three different alternative designs in a three-entry-system gateroad configuration with an inter-panel barrier in a longwall mine in Virginia. Starting with the current design, which has faced challenges such as excessive floor heave, a geomechanical model developed in 3DEC software is validated by monitoring in-situ pillar stress in the yield, abutment, and barrier pillars in the mine. Next, three different chain pillar designs are evaluated in the model with a focus on roof sagging, floor heave, and pillar average stress. Results show the relationships among the alternative designs and instabilities associated with roof, pillar, and floor in the study mine, providing insights for optimizing longwall mining designs in deep-cover settings.

Feb 1, 2025

By R. M. White

Abstract. Gulf Coast Salt Domes are being considered for radioactive waste disposal and this paper describes the geophysical techniques currently being used and those being considered for later phases of the program. Detailed gravity work utilizing a modification of the Talwani-Ewing modeling technique, shallow high resolution reflection seismic surveys using the mini-sosie concept, surface electrical resistivity and down-hole geophysical logging to add a third dimension to all of the surface techniques and to allow inverse modeling of the surface data sets are being utilized. The logic of the combined geophysical surveys will be discussed as well as their relative economics and their relationship to the overall exploration effort.

Jan 1, 1980

By David J. Dunn

Of many physical parameters critical to design of grinding processes, impact of grinding media is among the most difficult to measure or predict. Yet impact of falling grinding balls, pebbles, or rods accomplishes the fine grinding essential to metallurgical recovery of most important minerals. Unfortunately, the same impacts that break ore fragments deform or crack grinding mill liners. A project was undertaken at Climax Molybdenum Company to measure impact forces in operating ball mills so that they might be used to calculate stresses in liner materials and be correlated with service performance of mill liner alloys. Towards that end, a method of measuring impact forces on ball mill liners using an instrumented grinding ball has been developed. Preliminary tests show that impact forces and contact stresses imposed on bare mill liners are quite high but are greatly reduced by cushioning when coarse ore particles are crushed between balls and liners. Compressive and shear stresses induced in liners not protected by coarse ore are so severe that deformation or minute subsurface cracking are inevitable in all but the small production grinding mills, regardless of mill liner alloy strength or hardness.

Jan 1, 1977

By C. D. Harrison

This paper presents the results of 18 high-G centrifuge tests performed at the Electric Power Research Institute's Coal Cleaning Test Facility in January 1985. These tests, using -28 mesh (0.6mm) froth flotation product, show that the high-G, solid-bowl centrifuge can produce clean-coal moistures of less than 12 percent at solids recovery rates exceeding 98 percent. The high-G centrifuge achieved these low moistures by applying centrifugal forces up to 2,000 times gravity. Because these forces are two to three times the forces used in a screen-bowl centrifuge, the high-G centrifuge can use a solid bowl and still produce a low-moisture product. The solid bowl captures ultrafines that would pass through a screen bowl, and thus obtains higher recovery rates than a screen-bowl centrifuge.

Jan 1, 1985

By E. W. Bauman

The important role that mineral aggregates assume today in the construction and chemical industries is best attested to by the astronomical tonnage figures for the annual production of aggregates in the United States as reported by the U. S. Bureau of Mines in their "Minerals Yearbook." For 1965, latest publication available, the tabulation shows a total of 1,716,000,000 tons made up of 30,000,000 slag, 908,000,000 sand and gravel, and 778,000,000 crushed stone. A much more favorable statistical position for slag can be established by listing the world-wide tonnage. According to Dr. A, W. Lee, Director, British Slag Federation, in a paper presented before the 8th Annual conference of the British Institute of Works and Highway Superintendents, he estimates that the probable world consumption of slag is in the order of 100,000,000 tons showing--Great Britain with 10,000,000 tons, Germany, 15,000,000 tons, France, 1$000,000 tons and the United States with 30,000,000 tons. Thus it is seen that the United States accounts for almost one-third of the world's consumption of slag and the 3 west European powers another third.

Jan 1, 1967

The heat of immersion of coals in different immersional liquids is measured as a function of particle size and moisture content. Decrease in particle size shows a concomitant increase in the heat of immersion. The heat of immersion is dependent upon the nature of immersional fluids. In addition the nature of moisture present in coal influences the heat of immersion.

Jan 1, 1993

Mineral processing plant operators are faced with the necessity to choose between many different possibilities for plant improvement. Only a few such possibilities, however, can be tested on the industrial site. Steady-state simulators make it possible to assess the effects of several different flowsheet modifications in a few days, thus helping the process engineer to make his choice implement the solution that seems the most appropriate and check it. The example described here is the crushing and grinding circuit of the Shila Gold Mine, jointly owned by CEDIMIN SA and BUENAVENTURA SA, in Peru. Several possible modifications for the purpose of increasing capacity have been simulated and the results assessed in terms of technical quality, investment costs and energy consumption. The best solution indicated by the USIM PAC simulator was implemented and gave a 20% increase in capacity with a pay-back time of two months.

Jan 1, 1993

Electronic detonators have been in commercial use for a decade, with an excellent safety record. This paper lists known incidents involving electronic detonators. Typical standards required by regulatory bodies for static electricity and electromagnetic fields are reviewed. The performance of some detonators is compared to these standards; in general the minimum standards are easily exceeded. The general resistance of electronic detonators to extraneous electrical energy that can be derived from the body of test results is compared to danger levels for exposure of humans to these energies; it is shown that electronic detonators can safely tolerate higher electrical energies than people can. This comparison includes comparable data for electric detonators, which are shown to be more vulnerable to extraneous electrical energy than people are. Electronic detonators also bring significant safety benefits in blasting due to their testability, two-way communications, reliability, programmability and precision. The links between these attributes and enhanced safety are discussed with examples from actual blasting. Although electronic detonators are usually more vulnerable to extraneous electricity than non-electric initiation systems, the paper shows that the net safety benefit in handling and blasting is in favor of electronic detonators, which are the safest initiation system that has ever been offered to the mining industry.

Jan 1, 2010

By L. Yuan, R. A. Thomas

"Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the U.S. for the detection of fire in the belt entry and monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data has the potential to provide fire characteristic information such as fire growth (heat release rate) and exact fire location. This information is critical in making decisions regarding fire-fighting strategies, underground personnel evacuation, and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide (CO), carbon dioxide (CO2), and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division (PMRD) Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy. INTRODUCTION Fires at different stages generate different gases and smoke toxicity hazards. When fires occur in underground mines, a significant amount of toxic gases and smoke enter the mine ventilation system and are carried throughout the mine ventilation network, increasing the hazard potential for personnel even if far away from the actual fire. Although fires that develop to the point of rapid flame spread pose imminent hazards, fires in their smoldering, pre-flaming stages can also contaminate the mine atmosphere with debilitating levels of smoke and toxic gases. The most important parameter for evaluating the fire hazard in mines is the heat release rate (HRR), which is directly related to the rate at which heat, smoke, and toxic gases are produced and transported by the ventilation system, and provides an indication of the time available for escape or firefighting [1]. The HRR is also an important input parameter to mine fire simulation models. Measuring the HRR of an actual fire can be a difficult task. Early experimental measurement of HRR focused on the heat output as represented by the temperature of the product gases. In ASTM E1321 (LIFT test), an array of thermocouples was positioned in a duct which captured all gaseous combustion products to measure their average temperature. This approach assumed the flow is adiabatic, which is never a reality. Significant progress on measuring HRR was made when Huggett showed that, for most common materials containing C, H, O, and N, the average heat release per unit mass of oxygen is 13.1 MJ/kg O2 [2]. Thus, the oxygen deficit is a measure of the HRR in the flow that the duct captures. This approach is termed oxygen consumption calorimetry (or the oxygen consumption method), and is widely used in the fire protection community."

Jan 1, 2017

By D. W. Park

A vast majority of longwall operations in the United States use shield-type hydraulic supports to provide ground control along the longwall face. The three-dimensional finite-element technique combined with a progressive failure approach was utilized to simulate interaction between shields and surrounding strata and determine various loading conditions. In addition, a separate finite element model of the shield structure was made to study responses of each long wall shield to the different loading conditions. Shield responses under various loading conditions and the shield characteristics, such as shield stiffness, the ability of resisting horizontal forces, and the effect of shield height, were studied based on the results from finite-element analyses. The results can provide the basis of effective shield design and be used for evaluation of the shield performance. It is suggested to develop a technique incorporating the finite-element method to evaluate the real-time shield performance for the purpose of effective ground control.

Jan 1, 1992

By Michael J. Mankosa

Carpco has recently evaluated the use of various mineral processing techniques for secondary materials recovery. These applications include recycled foundry sands, plastics and secondary metals. This paper describes different recycling applications and the associated separation solutions. Results from extensive laboratory-and pilot-scale test work in each area are discussed. Industrial installations resulting from this test work will be presented. A detailed description of an industrial installation patented by Carpco for the recovery of plastic and metallics from current waste by-products is presented.

Jan 1, 1997

By Bruno A. Fichna

Longwall mining offers low cost potential for coal with high capital investment. As opposed to two shifts-per-day operation in most long- walls, Saarberg Mines in Germany increase utilization of capital by operating their longwalls around the clock. Differentiation between capital and operating costs, corrective maintenance versus preventive maintenance, improved roof conditions, and economical life of equipment was investigated. A surprisingly high degree of improvement was attained. Capital costs at Saarberg longwall coal mines have been reduced through a step-by-step research and trial program. This reduction was particularly influenced by the high performance pilot longwalls at the Ensdorf mine. The following presentation shows data and figures of those longwalls. End results were 40% reduction in capital costs, which could contribute favorably to investment decisions in the coal industry in a supply side economics environment.

Jan 1, 1982

By M. J. Beus

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a full-size shaft are underway.

Jan 1, 1999

By George W. Parker

The ever increasing costs of labor and supplies have made it imperative that operators of open pits look for some way in which to cope with these increases. One of the most logical ways to increase the efficiency of an operation is by the introduction of larger haulage equipment, as generally haulage costs are the greater portion of the over all expenses. These larger haulage units require larger shovel units. In the late 1930's and the early 1940's large mining, quarrying and heavy construction operations had more or less standardized on the 4 to 6 cubic yard shovels. During this same period the haulage units were generally 22 to 27 tons. Some ten years ago 9 - 13 cubic yard shovels along with plus 50 ton haulage units were introduced by manufacturers in an effort to enable operators to decrease costs.

Jan 1, 1962

By C. C. Huang

Rare earth compounds, such as samarium-cobalt compounds and neodymium-icon compounds, are being used more often for the manufacture of permanent magnets, because these materials permit the production of permanent magnets with higher magnetic energy potential than the conventional ferrite magnets. Especially, the recent rapid developments in the field of electronics and electro-technology have demanded an increased production of rare earth magnets. Unlike ferrite, which is typically produced by a wet process, rare earths can be ground and classified either in a wet or dry process. In the past, batch ball mills, through-pass ball mills in circuit with air classifiers, and conventional jet mills were primarily employed for the dry processing. These methods, however, have suffered from the problems, for example, wear and contamination, low product quality In particle size distribution, difficult to adopt inert-gas operation, and high specific energy consumption. In this report, dry processing of rare earth powders will be presented, especially ultrafine grinding with fluidized bed jet mill.

Jan 1, 1993

By L. Bloom

"Man-Made Parameters" refers to the importance of selecting appropriate analytical procedures to acquire useful chemical data. The correct procedures are particularly critical at the sample preparation stage where decisions concerning pulverizing equipment, sample size, contamination and dissolution will impact on the final results independent of the instrumental method of analysis. Several experiments were designed to quantify the impact of these approaches.

Jan 1, 1993

By F. Kitzinger

The possibility of increasing the efficiency of mineral processing plants by means of computer control has prompted metallurgists to examine their flowsheets more critically in order to develop practical control strategies. Control schemes in use to date generally rely on the automation of traditional and previously manually regulated control loops, for instance the addition of reagents to maintain a constant assay or a constant pH. This approach is predicated on the availability of well-established primary sensors such as pH electrodes or on-stream analyzers. Noranda Research Centre, in cooperation with Noranda Group concentrators, has developed a froth level monitor and a pulp density meter susceptible of application in this type of control. Although some of the basic principles on which they are based have been known for some time, their incorporation into the design of reliable, direct-reading instruments which can be interfaced with a computer, is be-lieved to be novel*.

Jan 1, 1977

By Richard P. Killmeyer, Carl P. Maronde, W. W. Wen, Peter J. Suardini

Under a cost-shared Department of Energy contract, awarded as part of the Coal Preparation Program&apos;s High Efficiency Preparation subprogram, Custom Coals International will be installing and testing a 227 kglhr micronized-magnetite cycloning circuit in PETC&apos;s Coal Preparation Process Research Facility. The project includes the design, construction, testing, and decommissioning of a fully integrated circuit complete with feed coal classification to remove the minus-30-micron material, dense-medium cycloning of the 300 by 30 micron feed coal using micronized magnetite (<10 microns), and medium recovery via drain & rinse screening and various stages and types of magnetic separation. This paper will describe the micronized-magnetite beneficiation technology and the scope of work for this project including an update on the status of the project, the circuit, and the proposed test plan.

Jan 1, 1995