Search Documents

By H. L. Bourne

The sand dunes which line the east shore of Lake Michigan resulted after the last, or Wisconsin, glacial period in Michigan. Melt-water streams carried vast quantities of glacial debris to the near shore areas of predecessors to Lake Michigan. As the lake levels receded, these vast quantities of sand were exposed to the prevailing westerly winds, which was the last major process that acted upon the sand and resulted in the formation of the dunes. 1 These dunes are one of the significant natural resources within the state. Michigan dune sands supply about 90% of the foundry sand used in the automotive industry, and 40% of the foundry sand used 2 for all purposes within the United States. The deposits owe their importance to the following factors: grain size distribution, grain shape, mineral composition and location with respect to the foundry sand market. In spite of their economic significance these I deposits are in jeopardy through legislative preemption.

Jan 1, 1975

By S. R. Dismuke

Ore at the Magmont Mine in southeast Missouri is extracted by the room and pillar method on two and sometimes three horizons. In 1991, an innovative plan was formulated for recovery of high grade ore in pillars using cable bolts to accommodate spans of more than 27 m (90 ft). A test area was subsequently selected and a recovery plan developed. A cooperative rock mechanics study effort by COMINCO METALS, the U.S. Bureau of Mines and the University of Utah was later established. When initially opened in 1968, the planned production rate was about 1,000,000 tons per year. Due to declining reserves, the production rate was decreased to 630,000 tons per year in November 1992. Pillar recovery now accounts for approximately 40%-50% of the mined tonnage and plays a vital role in allowing Magmont to continue to operate.

Apr 13, 2011

By Jim Finley, Adam Bedell, Eric Schrader

The CSO 52 Storage Tunnel and Pump Station project consists of 4,700 ft of hard rock tunnel, 2 intakes, and a 4 MGD wet pit pump station. During the geotechnical investigation, it was determined that the host geology contained abundant suldes. The purpose of this paper is to detail the investigation and subsequent determination that acid producing materials would affect the project during construction as well as long-term exposure of tunnel lining and permanent components during the operational life cycle of the tunnel and pump station. Details regarding the interaction between tunnel components and the acid producing material are also provided.

Jun 23, 2024

By Bruce D. Hanson

A computer model capable of simulating the basic production system in a variety of underground mining methods has been developed at the Twin Cities Mining Research Center. This Bureau of Mines paper describes the simulation of the basic production system at the working face, which includes drilling, blasting, mucking, and roof bolting. The model is event-oriented; that is, the status of the system is updated at the occurrence of an event. All event or activity times, including failure and repair of equipment, are treated as stochastic variables. A location dimension, in addition to the time dimension, is used, allowing the simulation of multiple location systems. To aid the user in determining the efficiency of his system, the model provides several reports. An event or activity report gives the frequency of occurrence total active time, and cumulative delay statistics for each event. An equipment report delineates the availability and utilization of all equipment. A production report provides information on various performance measures such as tons produced and holes drilled. The cost report gives the cost of various elements in the system. Operating data from an actual mining situation were used in validating the model. In addition to the description of the model, examples of simulation experiments which were performed on a room-and-pillar mine system are given. Use of the model to determine methods for improving the efficiency of the system is discussed.

Jan 1, 1974

By W. C. Streib

A wide variety of materials have satisfactory to superior insulating properties and can be used to control the flow of heat, provide energy savings, improve personal comfort and contribute to personal safety. Such materials range from completely organic products--both of natural origin and synthetics--to completely inorganic. In many cases, thermal protective systems are actually combinations of both. Obviously, those insulating materials which are principally inorganic have the inherent advantages of low to minimal combustibility as well as utility at vastly elevated temperatures. Both of these properties are highly desirable in providing not only thermal energy conservation, but also personal safety in residential and commercial applications. As the thermal insulation needs of man and industry have developed, there has been an ever-increasing demand on the minerals industry to provide the resources required to fill these needs. On a global scale, industrial minerals have become the fundamental base upon which today's thermal insulation industry has been built. The use of minerals to control heat flow range from the most unsophisticated applications to those requiring the ultimate in scientific technology. In many cases the minerals are themselves converted in- to the major insulating media; for example, fiber glass, rock wool or refractory fiber. In other cases, minerals are used as the chemical reactants to form the binder matrix which in turn provides the product strength required for adequate handling and installation; for example, calcium silicate bonded products wherein the binder is the reaction product of lime and silica. In still other cases, low density mineral products are added to a high density binder System to provide lower weight and better insulating properties; for example, the use of expanded perlite in concrete.

Jan 1, 1976

By Thomas A. Gwynn

"A beautiful America will require the effort of government at every level, of business, and of private groups. Above all it will require the concern and action of individual citizens, alert to danger, determined to improve the quality of their surroundings, resisting blight, demanding and building beauty for themselves and their children." "Improvement of our environment" has become a cause much like "motherhood". The increased awareness of the public concerning this subject makes it most unpopular for anyone to be involved in anything that seemingly is detrimental to our environment. And this awarement goes far beyond our biggest pollution problem in America - the distribution of paper, abandoned automobiles, beer cans and other garbage by our enlightened society along every city, highway, trout stream, river and mountain in America. In fact, the greatest awarement comes because of the "sensational" reporting and writing in our various national communication media, wherein the same voting citizens who so generously distribute their refuse about the countryside are emotionally aroused and duped into transferring what is truly a national problem onto the shoulders of a few industries - notably and particularly the mineral extraction industry. Certainly mankind is more and more stumbling over his own garbage daily, a fact that is easier to sell a citizen of one of our large cities than a resident of the wide open spaces of the west. Yet even in the Rocky Mountain states, the "Land of Sky Blue Waters", the "Big Sky Country", and particularly in Salt Lake valley smog is not unknown. Pollution and littering have become problems that need to be faced squarely. In North Dakota alone it has been estimated that one section of farm land each year flows down the mighty Missouri and the greatest producer of sediment is now reported to be the highway department.

Jan 1, 1969

By W. J. Turbeville

The subject of this discussion is timely. The U.S. phosphate industry is suffering the throes of depression. It's plight is a matter of widespread concern. The future role of the U.S. industry in world markets is of particular interest. If we should prognosticate phosphate supply-demand on the basis of recent history, we would face a puzzling choice of scenario. In 1980, perhaps the best year ever for U.S. phosphate, 54.6 million metric tons of phosphate rock entered the market place. Of this, more than half was exported -- divided almost equally - as rock or phosphate fertilizer. During the last half of 1981 the situation had begun to change.

Jan 1, 1983

By Richard E. Thill

Backfilling of mine voids is used to prevent or control the effects of subsidence on surface structures. The pumped-slurry, blind-backfilling process has been particularly successful for stabilizing ground over abandoned and inaccessible underground coal mines. Using this newer technology, vast quantities of backfill material can be distributed over wide areas in underground openings from a small number of injection boreholes. The rapid and successful development of this backfilling method, however, has outstripped technology for monitoring and controlling backfill placement. Surface or borehole remote sensing methods are needed to determine where fill material is being distributed underground and how effectively the material is packed in the voids. In search for improvements in backfill monitoring and control technology, potential remote geophysical sensing, process monitoring, and tracer methods were evaluated to select candidate systems for monitoring backfill placement under the constraints imposed by the injection process and the surface and subsurface conditions. ' A multiple objective ranking matrix, based on theoretical considerations as well as pragmatic experience with systems working in related or similar conditions, was used to narrow down potential methods to several most-favored candidates. Two of the candidates were field tested under actual operating conditions at a backfilling site in the Wilkes-Barre-Scranton region of northeastern Pennsylvania. Although process and acoustic emission monitoring indicated promise for improving existing backfill monitoring technology, more extensive testing under different conditions at various sites is required to establish the validity and utility of these methods. Results indicate that no single method is adequate in itself for backfill monitoring, and that a successful system will require the Integration of several methodologies.

Jan 1, 1982

By B. A. Filas

Stabilizing fine coal refuse ponds for reclamation at Monterey Coal Company's No. 1 Mine has been difficult. Entrained water in the stored refuse causes liquefaction as reclamation caps are placed, resulting in additional material requirements than originally projected to stabilize the pond surface. Laboratory results indicate that in-place refuse densities may be substantially improved at No. I Mine by converting from a single-point to a managed slurry distribution system. Increased densities result in improved storage efficiency, less entrained moisture and a more stable refuse mass, thereby providing an improved working surface for reclamation and improved post-closure cover stability.

Jan 1, 1993

By J. Fox, C. Allen, A. Greth, K. Kocsis

"It is the duty of the mine operator to ensure the mine environment is healthy and safe for the mine workers. For deep and hot underground mines, this requires maintaining adequate working temperatures by means of mitigating the heat load generated by strata, auto-compression, mining equipment, explosives, ground water, and human metabolism. The heat load is best reduced by minimizing the amount of heat transferred to the mine air from these sources and through the use of efficient ventilation with effective cooling systems. The heat emitted by mining equipment and vehicles contribute a significant proportion to the combined heat load of an underground mine. This is especially a problem for diesel equipment due to the fact that besides heat, a large amount of water vapor is produced, which increases the humidity in the production workings. Diesel engines have proven advantageous in recent history due to their high power output and reliability. However, as mines continue to become more mechanized and deeper the climatic problems introduced by elevated heat generation will continue to rise. With that, the issue of heat generated by diesel equipment must be addressed. The economic alternative for diesel engine equipment fleets in underground mines is the electric engine. Technological advances in battery technology, increased mechanical output and improved reliability have made the electric engine significantly more competitive in comparison to diesel engines. Because electric engines do not utilize internal combustion, the heat produced by them is significantly less than of the diesel engines. Battery powered mining equipment likewise eliminate diesel particulate matter (DPM) produced by diesel engines. Utilizing battery electric equipment in underground mines provides many advantages, such as: (a) reduced heat load, (b) healthier and safer environment for the mine workers, and (c) reduced mine operating costs due to lower ventilation requirements. This paper will highlight the health and cost benefits of using battery/electric fleets versus diesel fleets in deep and hot underground mines. The study analyzes simulations produced from thermodynamic ventilation models. Early simulations show significant cost reductions in terms of net present value (NPV) when comparing the air volume requirements for battery/electric equipment versus diesel powered equipment for the same production rate. INTRODUCTION The competitiveness of the world mineral market demands that mine operators continue to increase production and decrease costs as commodity prices fluctuate in often unplanned directions. This has forced underground mines to operate at deeper depths and to become more mechanized to remain competitive. Because of these changes, ventilation challenges have continued to increase as the mines combat an enlarged influx of contaminants such as heat and diesel particulate matter (DPM)."

Jan 1, 2018

By Wenkai Wan, Charlie C. Li

Strain burst can occur in underground hard rock excavation when the in-situ stresses are high enough. The prerequisite for rock burst is that the total energy released from the rock mass is higher than the energy needed for rock fracture. The total released energy is contributed by both the burst rock and the surrounding rock. The part of the energy from the burst rock is constant per unit volume of the rock, but the part from the surrounding rock is associated with the burst volume. A greater amount of energy will be released from the surrounding rock in the case of a larger volume of burst rock. The postulation for the energy conversion in strain burst is verified through a FLAC3D model in the paper. It is assumed that the strain burst occurs in a circular tunnel that is located in the hydrostatically loaded rock mass in the model. Six pairs of notches with different depths are created in the opposite walls of the tunnel to simulate the bursts. The energies released from the notch rocks and from the surrounding rock are calculated during the burst. The simulation results show that the percentage of the energy released from the surrounding rock in the total released energy increases with the notch depth. The numerical modelling confirms the postulation that the surrounding rock contributes more energy than the burst rock itself in large-scale strain bursts

Apr 26, 2022

By D. R. Gehring

Effective project management is an excellent technique for meeting a goal through set, well-defined objectives. Even though project management is successfully used throughout the world in various construction projects, underground mining has unique characteristics that require approaches that vary from classical project management theory. Typically, a project includes four main stages: definition, planning, implementation and control. Definition and planning are often the most overlooked stages, but are arguably the most important. This paper addresses practical techniques for the definition and planning of projects for underground construction.

Jan 1, 1996

By B. Kolonja

A SIMAN and CINEMA PC-based simulation model was developed to simulate and animate the truck-shovel operations of surface mines. The model is capable of simulating one mathematical dispatching strategy using linear and dynamic programming and six heuristic dispatching strategies. Data were collected from an actual operating mine through time studies and analysis of historical records. The statistical analyses were performed and appropriate theoretical distributions were fitted for various time events in the truck-shovel work cycle. The model was then applied to study overall impact of these dispatching strategies on constrained and unconstrained mine productivity. The simulation/animation model developed in this study seems to be an efficient planning tool for choosing optimal fleets and finding an 'optimal" dispatching strategy to produce an equilibrium between "the quality and quantity of production.

Jan 1, 1993

By W. G. Pariseau

Recent advances in rock mass mechanics and computational technology now allow for stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time-dependent. All the usual dry mine parameters including the premining stress state and rock mass properties are taken into account, in addition to water pressure and flow in jointed, possibly porous, rock masses. Finite element analyses of shafts and tunnels as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor, or equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and that the minimum safety factor at the wall in the wet case is always less than the dry case regardless of drainage time allowed.

Jan 1, 1995

By S. Perla

Two of Peabody Western Coal Company's mine operations are the focus of this paper ... Black Mesa Mine and Kayenta Mine, both located in Northern Arizona. These two locations are unique for a variety of reasons. ? The two mines have only two customers, both power plants, one the Southern California Edison's Mohave Generating Station near Laughlin, NY, the other the Navajo Generating Station near Page, AZ. Close in proximity, these two locations ships nearly 12 million tons of coal per year. ? Material is shipped to these customers two ways: via a 273 mile underground slurry pipeline, which by the way is longest in the world, and by a 17 mile long conveyor to four storage silos. Product is then shipped via train from the storage silos to the plant sites.

Jan 1, 1995

By W. Wan

Diesel particulate matter (DPM) emitted from diesel engines is currently considered to be a health problem in underground mines. As a result, attempts have been made to control DPM both by reducing emission rates and by managing the DPM that gets into the mine atmosphere. This paper presents a method for modeling the generation, transfer and distribution of DPM in the mining sections through the use of a convection-based computer model so that controls for emitted DPM can be evaluated. A variety of ventilation strategies and diesel deployment schemes for room-and-pillar development sections were simulated to compare their effects on average DPM concentrations at several fixed and mobile personnel locations in the section. Input data for the model was gathered from actual diesel development sections and derived from experimental study results provided by other researchers. Studied using the model were ventilation schemes using vent tubing and brattice, exhaust location strategies on the vehicles, and the direction of ventilation at the feeder-breaker location. A summary of results from this study will be presented.

Jan 1, 1994

By T. E. Wilson

In conjunction with experiments to improve the particle size preparation of coal bore cores prior to washability testing, discrete-event breakage of coal, shale and homogeneous low-strength concrete cores was studied. Breakage of individual size classes by drop-shatter and by incremental tumbling in an end-over-end hand-driven tumbling cylinder revealed systematic changes in the breakage function, namely, that breakage in any size class diminishes as the number of events increases. The effect of the fines removal enhances the breakage of harder material (having lower grindability indices), but appears to have less effect for softer material.

Jan 1, 1998

By J. P. McKinney

Benchtop experiments were performed, in which an electric field was used to enhance separation of water from phosphatic clay suspensions from a central Florida mine. A constitutive relationship was established that relates the increase in solids content to operating time and the applied electric field. An upper limit to the degree of separation was found to be a function of electric field, and the time required to achieve this limiting value was also a function of electric field. The energy requirement for removal of water ranged from 1.25 to 175 Wh/kg water removed as a function of the electric field. A mathematical model was developed that provided good agreement to the experimental values and served to validate the constitutive relationship.

Jan 1, 2011

The strength of anchorage of various types of roof bolts in permafrost depends on the types of rock in which they are installed. Variation in the mine thermal regime results in weakening of the roof and walls, and at times total loss of ice cement bonds takes place in the surrounding rockmass. In mines with positive ventilation air temperature, the wedge or expansion types of bolts may become weakened due to the transfer of heat into the anchorage through the metal rod and subsequent thawing of rocks. Effective operation and evaluation of roof bolt systems for mine workings in permafrost require predictions of the dynamics of wall thawing by warm ventilation air. This paper presents an analysis of the temperature distribution in the frozen host ground surrounding roof bolts, the area of interest being the vicinity of the anchors for point anchored bolt and the entire length for split set bolt

Jan 1, 1994

By M. Fig, A. Juganda, M. Zurhorst, J. Brune, C. Strebinger, G. Bogin

"Understanding the airflow patterns in and around the longwall panel can help to identify poorly ventilated areas that may be prone to methane accumulation. Ventilation network modeling provides quick simulation time, and flexibility in adjusting airway parameters and ventilation controls. Such modeling is effective for analyzing linear ventilation networks in underground mines, but cannot compute flows in caved areas of hard rock mines or longwall gobs. The use of Computational Fluid Dynamics (CFD) enables a more detailed investigation of the interaction between the airflows in these caved areas but requires much longer computational times, designing complex meshes and determination of a variety of modeling parameters. Airway friction factors and ventilation controls are simple to implement in a network model but can be difficult to model and adjust in CFD. This paper will focus on using mine ventilation network simulation to identify and analyze key parameters that are affecting airflow distribution in and around the longwall panels, prior to more detailed analysis with CFD modeling, using the example of a longwall coal mine. INTRODUCTION In longwall coal mine ventilation systems common in the U.S., the main purpose of bleeder ventilation is to dilute methane gas and prevent the formation of explosive gas mixtures in the caved, poorly ventilated gob areas and adjacent mine workings. In longwall operation, these critical areas include the development headings inby the longwall face, and the gob. Methane-air explosions in these areas may be ignited by spontaneous combustion, rock-on-rock friction and other sources. Although rare, ignitions due to rock-on-rock friction caused by roof falls caving into the longwall gob are possible and were suspected in the Willow Creek mine explosions in 1998 and 2000 (Elkins et al., 2001; McKinney et al., 2001). Rock-on-rock frictional ignitions are difficult to prevent, as they occur in inaccessible areas. Therefore, rendering the gob area inert is essential to prevent the formation of explosive mixtures. Research by Gilmore et al. (2015) and Brune et al. (2015) has shown that gob inertization can be a difficult or impossible when using bleeder systems, since the flow of gases through the gob depends on the gob permeability and the amount of fresh air leaking from the face and the immediate roof caving conditions cannot be controlled by the mine operator. Having the ability to predict the location where explosive gas zones (EGZs) form inside the gob will be helpful for designing the best ventilation setup to minimize explosion and fire risks."

Jan 1, 2018