Search Documents

By R. S. Saunders

Congress, under the Nuclear Waste Policy Act of 1982, as amended, charged the U.S. Department of Energy (DOE) with the responsibility for safe and permanent disposal of high-level radioactive waste in a geologic repository. The waste will consist of spent fuel from commercial nuclear generating plants and reprocessing activities. Under direction of this law DOE is currently evaluating Yucca Mountain in Southern Nevada as the candidate site for a potential high-level radioactive waste repository. Presidential, Congressional and State of Nevada approval are needed for repository construction to proceed after successful completion of site characterization and recommendation of the site to Congress. The DOE will submit a license application to the Nuclear Regulatory Commission (NRC) to construct the geologic repository. Following successful construction DOE will update its license application to operate the repository.

Jan 1, 1993

By M. Solomon

Crushers are designed and manufactured to survive the severe duty of mining environments worldwide. Under these conditions the crusher performance and availability is one of the critical factors in the mine?s production and profitability. Traditionally the development of these machines tends to be experience-based, incremental improvements in design due to challenges of different applications, duty, or manufacturing. In order to better serve the mining industry a new approach was taken to the design of primary crushers. This approach was to focus on safety and maintenance activities. The result of this effort is a new generation of gyratory crushers that can be serviced from above. Using the features of this new generation of crushers to their fullest extent crushing installations have improved safety, reduced design and construction costs, and lowered maintenance requirements. This presentation explores the benefits of two crusher installations utilizing top service crushers.

Jan 1, 2010

By Don Cchultz

The United States Forest Service, as a land managing agency, is responsible for the surface administration of National Forest lands. The basic objectives of management are protection and utilization of renewable resources such as water, forage, timber, wildlife, recreation, and clean air. Much of the National Forest land in this country is open to mineral prospecting and development. When large de-posits of minerals are extracted from the forest environment, especially by surface methods, there are oftentimes conflicts between accepted mining methods and the objectives of other resource management goals. Such is the situation in Southeast Idaho where several members of the phosphate industry are operating on and adjacent to the Caribou National Forest. In 1966, the phosphate industry and the Caribou National Forest became mutually concerned with the problems of rehabilitating mined areas and minimizing potential damage to adjacent forest areas. A Cooperative Administrative Study was initiated with industry supporting the Forest Service financially and with equipment, material, and manpower, as well as interest and enthusiasm. The objectives of the study are to provide basic, applicable information pertinent to: 1. Protecting the quality of water emanating from mined water-sheds. 2. Providing for soil stabilization on mined areas. 3. Returning mined areas to surface resource production. 4. The feasibility of making mined areas esthetically acceptable. It was concluded that the following separate--yet intergrated--fields should be studied in order to obtain the desired information:

Jan 1, 1971

By Gerald Zink

The work described in this paper is sponsored by the Bureau of Mines for the purpose of accelerating the drilling of roof bolt holes and reducing the quantity of materials needed to fill each hole. A high-speed small-hole drill has been fabricated and tested in the laboratory. High priority has been given to safety, reliability, and compatibility with underground coal mining practice. The combination of drag bits and erosion jets is designed for high penetration rate, long wear life, and uniform hole size in a variety of sedimentary strata. A reliable high-pressure high-speed swivel feeds water to the bit at about 4 1/min (1 gpm). The duplex hydraulic intensifier which drives the jets has a 40 kw capacity (30hhp) Results of recent full-scale laboratory testing are presented.

Jan 1, 1978

By Richard Kojo Gabah

Western mining companies are entering an African critical minerals market where access is harder to secure, risk is being priced more sharply, and execution advantages are increasingly decisive. The continent holds significant reserves and production potential of cobalt, lithium, copper, graphite, manganese and rare earths critical to the energy transition, yet Chinese-aligned capital has built a structural edge in access and execution speed. Simply signing narrow offtake agreements to buy output is no longer sufficient. Western firms win when they convert quality orebodies into bankable projects by reducing aboveground risk faster than competitors through integrated infrastructure access, durable fiscal alignment, and credible local value creation. Western mining companies will break into Africa by pairing capital with partnership, building corridors enabling infrastructure and power, designing credible value addition pathways and operating in a way that is politically durable through transparency, community benefit and fiscal terms that share upside in commodity upcycles. This feature article offers a practical playbook for mining executives and investors. The core argument is straightforward. Winning in Africa requires competing on the full system around the mine. Corridors and power, processing pathways, contract durability, community benefit and regulatory execution are now decisive variables in project valuation and capital access.

Mar 1, 2026

By John M. Smith

Kaolin is an important industrial mineral because of its unique properties and low cost. Strictly defined, kaolin is the name given to a group of hydrous aluminum silicates of which kaolinite is the most common mineral (1). Through common usage the mineral, kaolinite, is called "kaolin" or "china clay". In 1972 over 4, 000, 000 tons of kaolin will be beneficiated and shipped by domestic producers. By far the largest user of kaolin is the paper industry which utilizes approximately 65 to 70 per cent of the total production. Kaolin is used in paper as a filler in the interstices of the sheet and as a coating to impart smoothness, gloss, brightness, and printability to the paper. The rubber industry is also a large user of kaolin where it is used as a filler because it adds strength, abrasion resistance, and rigidity to both natural and synthetic rubber goods. Kaolin is used as an extender in paints because it is chemically inert, has a high covering power, gives desirable flow properties, and is low in cost. In ceramics, kaolin is used in whitewares, tile, insulators, refractories, and in some face brick where a white color is desired. Kaolin is also used extensively in plastics as a filler in thermosetting and thermoplastic mixes to give smoother surfaces, a more attractive finish, good dimensional stability, and resistance to chemical attack. Many other process industries use kaolin as a filler, suspending medium, or for color improvement.

Jan 1, 1972

By Louis Schaarschmidt, Helmut Mischo, Ibrahim Alsalamin

In order to store high-level radioactive waste underground, the German repository concept considers clay, crystalline and salt formations as suitable host rock materials (National Citizens’ Oversight Committee, 2024). The current research projects of the Chair Underground Mining Methods at TUBAF (Technical University Bergakademie Freiberg) in nuclear waste repositories mainly focus on storage within salt formations. In this scenario, the high-level radioactive waste is supposed to be packed into specifically designed containers and then transported underground and emplaced in horizontal storage drifts. The residual temperature of the radioactive waste leads to the question if there are optimization possibilities for waste handling, the storage and the long-term emplacement of such high temperature level waste. A deeper understanding of the heat transmission from the container into the host rock might lead both towards possibly shorter surface interim storage times as well as size optimization possibilities of the repository itself. TUBAF has conducted research that successfully proved that an optimized container positioning yields more favorable thermal patterns and can be achieved with conventional mining equipment.

Feb 1, 2025

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By R. D. Coursen

Tin has been one of the very few commodities which has been covered by an international commodity agreement. It is the only metal so covered. The reason behind tin's prediliction for an agreement has been the inconsistency of the price pattern for tin during the entire 20th century. It is not surprising in view - of the wide and wild fluctuations in its price that tin has been called the Cinderella metal. An examination, for example, of prices in 1977 alone attests to the erratic behavior of the tin markets. The high was recorded on October 27 at M$1,895 per picul and the low on January 3 at M$l,314 3/8, on the Penang market, a spread in Malaysian dollars of $581 for a picul weighing 133 1/3 pounds. The first steps in international cooperation on tin were taken after the price bonanza of the First World War. Despite a lack of increased consumption, and in spite of the fact there was no shortage of mining production during the war, prices boomed. Shipping shortages and thinning stocks brought about a situation where in the U.S., industrial stocks were only 1/6 of what they had been in 1914. The boom busted early. In 1921 the tinplate industry of the world had cut its output in half and total world consumption of tin fell by 1/3. Tin producers became so concerned that they created what was called the Bandoeng Pool. It accumulated stocks held by countries now known as Indonesia and Malaysia, amounting to 28 percent of the combined production of the two countries and about 15 percent of the total world for 1921. The pool holdings were shortly exhausted and thereafter in the years 1924 to 1928, general boom conditions existed for tin.

Jan 1, 1978

By R. W. Sayers

The Duval Corporation porphyry copper deposits at Copper Canyon and Copper Basin, though widely separated, form an economic unit requiring integrated exploitation. Contrasts in mineralization, host rocks, and mode of occurrence present unique mining and milling problems. Mixed oxide-sulfide ore is treated in extensive dump leaching facilities in both areas. Complex copper-gold-silver ore is treated in a 4,000 tpd mill at Copper Canyon. In both areas, hypogene metallization occurs within large aureoles of metamorphism and hydrothermal alteration related to quartz monzonite intrusions of mid-Tertiary age. Supergene processes further altered the rocks and enriched the hypogene protore. At Copper Canyon, hypogene copper and iron sulfides with gold and silver occur in fractures, as partial replacement of favorable beds, and as disseminations in Paleozoic sedimentary rocks. The lower part of the Pennsylvanian Battle Formation was a particularly favorable host. Metallization occurs to a lesser extent in quartz monzonite. Metal zoning is well developed. The deposits at Copper Basin consist principally of supergene copper minerals in arenites of the Cambrian Harmony Formation. Oxidation of hypogene copper and iron sulfides in tactite zones has formed at least two commercial deposits; intersections of fractures with favorable beds exerted important ore controls.

Jan 1, 1968

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

As indoor positioning provides particular challenges due to the unavailability of GPS signals, various systems such as ultrawideband (UWB), radio frequency identification (RFID), ultrasound, and wireless local area network (WLAN) have been proposed in recent years. Some of these technologies are currently being marketed and some are still being developed. UWB technology allows for higher precision while also reducing power consumption. Hence, the underground automation and localization systems can use this technology for more accuracy and robustness. This article discusses new robust UWB modules used for underground positioning and collision avoidance with regard to human safety in underground mining operations.

Jul 31, 2020

By LeEtta M. Shaffner, John R. Marks

INTRODUCTION In the last twelve years, underground stoping methods at the Homestake Gold Mine have evolved from open cut-and-fill with jacklegs, cribbed raises and electric slushers to ramp-based mechanized cut-and-fill (MCF) and vertical crater retreat (VCR) with dieselpowered loaders, trucks and drill jumbos. The evolution was swift. Unfortunately, ventilation practices have had trouble keeping pace. Stope ventilation is still too dependent on auxiliary fans and coolers. A single large MCF stope might contain up to eight headings, each of which requires significant ventilation resources when a diesel loader is present. Air is shortcircuited all too frequently through mined-out VCR panels. These factors and the recent rapid decent of the center of mining prompted a study to improve ventilation practices and to more accurately project future requirements. BACKGROUND In 1992, the underground portion of the Homestake Gold Mine produced 8336 kg of gold from 1407 ktons of ore (268,000 oz from 1,551,000 st). The ore is hosted in low to medium grade meta-sediments. Stoping took place from 420 to 2347 m below the surface (1400 to 7700-ft levels). The weighted center of mining was 1662 m deep (5450-ft level) in 1990 and is projected to be 1890 m (6200-ft) in 1993. The deepest level is 2440 m (8000-ft) where the virgin rock temperature (VRT) is 56.1°C (133F). The mine is ventilated by 504 m3/s (1,069,000 cfm) measured at mid-exhaust-circuit density. The air-conditioning system includes an 8.1 MWR (2300 ton) controlled recirculation plant, a 2.0 MWR (580 ton) chilled water plant, a 1.0 MWR (290 ton) exploration drift refrigeration plant, 28 spot-coolers totaling 3.4 MWR (960 tons) and 35 spray coolers totaling 1.5 MWR (420 tons). The mine employs 117 diesel units with a total nameplate rating of 7961 kW (10,672 hp). These units include twenty-four 1.5m3 (2-yd) loaders, twenty-six 2.7m3 (3.5-yd) loaders, fourteen 3.8m3 (5-yd) and two 7.6m3 (10-yd) trucks, and assorted utility vehicles and drill jumbos. THE STUDY In April 1991, the University of Nevada-Reno (Mackay School of Mines) and the South Dakota School of Mines and Technology cooperated with Homestake on an MCF study. Mackay instrumented a stope with thermocouples, air velocity meters and hygrometers (Duckworth, 1992). South Dakota Tech conducted a finite-elements computer analysis of a back-filled MCF stope with/without light-weight shotcrete insulation on the sidewalls and back (Chellam, 1992). Homestake conducted an empirical analysis of deep-level MCF stoping. This paper describes the Homestake study. Twenty-three of the forty MCF stopes deeper than 1800 m were surveyed at least once during the last quarter of 1992. The stopes not included were being cable-bolted or back-filled. Figure 1 shows the complexity of one of the ramp-based stoping areas included in the survey. This particular stope has six separate production headings. A baseline wallrock heat load was derived for each stope or heading from psychrometric calculations. Broken ore, waste rock fill and fissure water were noted when present and the effects included in the baseline heat load. Other heat sources often mentioned in the literature such as metabolic heat from workers, heat from explosives and small electric loads were neglected. Fan heat was considered part of the ramp & crosscut heat load and thus not included in the study. Diesel heat was addressed separately. RESULTS Survey results, plotted as the heat flux against VRT, are shown in Figure 2. The equation for the regression line is: W/m2 = 2.1236*VRT - 75.405 The 0.31 correlation coefficient is poor which implies that the results should be used cautiously. Previous experience strongly suggests that differences in productivity are most likely responsible for the scatter in data points. A rapidly advancing stope will have a

Jan 1, 1993

By A. D. Davis, C. J. Webb, A. Heriba

Introduction The disposal of spent ore from cyanide heap-leach processing facilities is of concern to the mining industry, the regulatory agencies and the general public. The disposal of an additional several hundred million tons of spent ore from heap-leaching operations is planned in the western United States during the next decade, and this amount could increase if gold prices rise. In the past decade, more than fifteen million tons of spent ore have been disposed of in the Black Hills of South Dakota. The criterion for offloading spent ore was set by the South Dakota Department of Environment and Natural Resources at 0.5 ppm weak acid dissociable (WAD) cyanide. South Dakota's nitrate offloading limits vary for each mine, depending on ore type and other factors. Concentrations of nitrate in the leachate from spent ore depositories could be the result of conversion from other nitrogen-containing species. One likely source of nitrate is residual explosives from the blasting of ore. Previous work on the combustion products of nitrogen explosives has shown incomplete oxidation (Johansson and Persson, 1970). Another likely nitrate source is the degradation of cyanide to ammonia, followed by oxidation to nitrite and nitrate. A third possibility may be leaching of background nitrate from soil or rock. Objective The primary objective of this research was to investigate laboratory procedures for predicting nitrate concentrations in effluent after the disposal of spent ore at heap-leach gold processing operations. Laboratory tests were performed to define the concentrations of nitrate and nitrite in leachate as a function of time. Sources and species conversions were examined by investigating the nitrogen contributions from cyanide neutralization and from blasting with ammonium nitrate/fuel-oil (ANFO) explosives. Ore processing at cyanide heap-leach facilities Gold mines in the northern Black Hills of South Dakota normally use the following steps in their heap-leach cyanidation processing: Blasting. Surface gold mines in the Black Hills use ANFO explosives (approximately 95% ammonium nitrate and 5% fuel oil). Field evidence and studies show that explosives often fail to ignite or burn completely in shot holes. One reason is that ammonium nitrate absorbs moisture readily, which reduces blast efficiency. Ferguson and Leask (1988) cited a study conducted at the Fording coal mine in southeastern British Columbia. In that study, the total nitrogen released to surface and ground water was estimated to be about 6% of the slurry explosives. However, Ferguson and Leask (1988), in a later analysis of water quality near coal mines in the Kootenay coal fields, indicated that this is likely an overestimate of the nitrogen release. Mines that used ANFO explosives in dry conditions released 0.2% of the nitrogen from blasting. Cyanidation. At surface gold mines in the northern Black Hills, cyanide species from heap leaching can be classified into free cyanides and simple ions, weak complexes, moderately strong complexes and strong complexes (Scott and Ingles, 1981). Degradation of cyanide and disposal of spent ore. Methods of destroying cyanides include hydrogen peroxide oxidation, natural degradation and evaporation, water leaching and alkaline chlorination. Hydrogen peroxide is used to oxidize cyanides in the northern Black Hills mining area. The hydrogen peroxide oxidation reaction forms cyanate, which can hydrolyze to form ammonium and carbonate ions. After formation of ammonia or ammonium ion, further oxidation to nitrite (NO2-) and nitrate (NO3-) can occur. Spent tailings from gold processing in the Black Hills normally are disposed of in tailings facilities constructed in nearby drainages. Infiltrating rainwater with a typical pH of about 5.6 is an additional component introduced into the spent ore after disposal. Methods Field sample collection. Spent ore samples were collected from conveyor belts (or other convenient points) at heap-leach mines by personnel from the South Dakota Department of Environment and Natural Resources. The samples were placed in black plastic bags that were contained within 5-gal buckets and sealed to prevent exposure to ultraviolet light. The samples had a minimum head space to limit evaporation and contact

Jan 1, 1997

By N. D. Jagger, I. M. Arbuthnot

Introduction Over the last five years, a large number of small- to medium-sized carbon-in-pulp treatment plants have been built in Australia, most designed to treat between 250,000 t/a and 1.5 Mt/a of ore. Because of the limited capital resources and tight cash-flow positions of these relatively small mining companies, the primary requirement was often to get a plant built and operating in a short period of time and at minimal capital cost. Therefore, since the inclusion of both pre-leach and tailings thickeners represents an obvious and significant capital cost, most of these plants were built without thickeners or even detailed, cost-benefit analyses on their inclusion. In some cases, the increasing use of High Rate Thickeners (HRTs) in the mineral processing industries has, however, resulted in a reassessment, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas where borefields are costly to install and water is limited. With the startup and operation of these installations, the resulting significant savings in cyanide consumption has been recognized, in many situations, as a primary justification for the installation of HRTs. Solution balances Degradation of cyanide occurs in the tailings water discharge to slime dams. The degree of degradation (cyanide loss) in the water recovered depends on a number of factors, but it is usually assumed to be about 90%. The most important mechanisms of CN loss are through HCN losses and oxidation by oxygen in the air, which also assists in the hydrolysis of CN. These mechanisms are supported by the large dam surface area and the long retention time of the tailings water in the dam. By thickening the CIP tailings at the plant and recovering as much tailings water as immediately possible, these losses are avoided. The retention time in an HRT is less than three hours, and the surface area is relatively small. Therefore, CN losses are negligible, which is not necessarily the case in conventionally-sized thickeners. Fig. I shows a block diagram of a 100-t/h gold plant without a thickener. In this example, 50% of the tailings water pumped to the tailings dam is recovered, and the CN concentration of the returned water is 10% of the tailings CN concentration of 150 ppm. Fig. 2 represents a plant with an HRT on tailings, thickening to 55% w/w solids. In this case, the thickened tailings are pumped to the dam, and 25% of the contained water is recovered. The recovered water and the mill make-up water are not sent directly to the mill; instead, they are added to the thickener feed and mixed with it prior to thickening. By doing this, the tailings are effectively washed, and the additional cyanide is recovered. Solution balances over these two circuits show cyanide recoveries of 5% and 65%, respectively. Thus, the thickener use increases cyanide recovery by 60%. Fig. 3 shows a two-stage HRT circuit in a countercurrent decantation (CCD) configuration. In this example, an additional 13% of cyanide is recovered through the use of the second-stage unit. This configuration can be justified when residual cyanide levels are high. Capital and operating costs - Case study 1 Illustrative cost figures are based on a CIP tailings thickener installed, in early 1988, as part of Dominion Mining's treatment plant at Paddy's Flat near Meekatharra. (All costs within this paper, unless stated otherwise, are in Australian dollars.) [Assumptions: Feed rate 150 t/h Ore moisture content 5% Leach density 40% solids Underflow density 55% solids Residual cyanide in tailings 150 g/m3 Flocculant dosage 15 g/t Consumable costs: Water $ 0.40/m3 Cyanide$ 2.00/kg Flocculant$ 4.50/kg Power$ 0.12/kWh Length of tailings pipeline2,500 m Capital costs of the major items involved in the thickener installation are given below: Thickener unit, 15-m diam $ 230,000 Water return pumps 12,000 Water recirculation pumps 28,000 Feed box 5,000 Flocculant make-up system 18,000 Flocculant storage tank and dosing pumps 11,000 Piping and valves 85,000 Electrics and instruments 47,000 Civil works 29,000 Installation 69,000 Total cost$ 534,000] Savings in capital costs that can be attributed to the

Jan 1, 1993

By Don Suttie, Frank Roybal, John Wright

The Roybal Raise incorporates the simplicity and low cost of a short bald-headed raise while overcoming the usual impediments to driving a high baldheaded raise. The concept provides for speedy excavation and maximizing the use of the excavated opening, using the rock for structural support. The design is simple: two baldheaded raises are driven parallel to one another, interconnected by dogholes about 8 m (25 ft) apart. In this fashion, the raise can be driven safely and efficiently to 60 m (200 ft) or more. When the raise is complete, the excavation requires no timber for support or partitioning. Rather, the rock itself supports the construction. As a test, a two-compartment Roybal Raise was attempted at the Independence mine in the Willow Creek District of Alaska. One side was driven 2 x 2 m (6 x 6 ft), intended for a manway and equipment skip. The other was driven 1.5 x 1.5 m (5 x 5 ft) for a muck compartment. Both sides were driven at a 65° angle from horizontal and 1 x 1 m (4 x 4 ft) dogholes spanned the 4.6-m (15-ft) pillar between the two compartments. After topping out at 50 m (160 ft), the raise was found to meet all expectations of efficiency, low cost, and practical simplicity. Technique Preparing the Roybal Raise for driving involves no elaborate or costly site prep except assembling materials and providing for muck removal. Normally, the raise muck falls directly onto the sill or track and is picked up either by an overshot mucker or a front-end loader. Raise mining proceeds initially by taking up both compartments simultaneously to the first doghole. It progresses by alternating one side as a clear manway for access with the other side, the active side, as a muck compartment (Fig. 1A). This stage proceeds quickly for no mucking or staging is required to cycle the first three rounds. On the fifth round, in addition to the normal raise round, rib holes are winged out toward the adjacent raise, thus starting the dogholes. Finally, as the sixth raise rounds are drilled and shot, the first doghole is also completed from both sides. The second stage commences by establishing one side as a clear manway for access while the other side, used as a muck compartment, is prepared for active mining. Figure 1B illustrates this step in the succession of raising with the active side advancing to the second doghole level. During this stage, services are maintained through the manway side and equipment is stowed in the doghole during blasting. As the active side advances, muck may be allowed to fill the bottom portion of that side since it is unnecessary to clear it for access. The next stage of raising involves cleaning out the former muck compartment and preparing it for use as a manway. At the same time, the former manway is prepared for advance and use as a muck compartment (Fig. 1C). As in the previous step, the same doghole is used for access and equipment storage. The active side advances until the second doghole is completed, at which point equipment and access are moved to the new doghole. From there, the active side is driven past the second doghole 8 m (25 ft) more to the third doghole level. Again, half of the doghole and the next raise round are mined. The fourth stage involves switch ing back the manway side for the muck side (Fig. ID). The new muck side is driven to the third doghole where equipment storage and access are reestablished. From there, the active side is advanced to the fourth doghole. In the same fashion, the raise is advanced to the top, alternating the manway side with the active side, maintaining access through the inactive manway, and storing equipment in the uppermost doghole. The cycle time for driving each compartment, regardless of the raise height, is greatly improved over that for normal bald-headed raises of comparable height. By storing equipment in the upper-

Jan 1, 1984

By Elza Burch

Introduction The feeding to zero concept involves feeding 600 µm x 0 (28 mesh x 0) size raw coal to heavy media (magnetite) cyclones along with the +600 µm (+28 mesh) size coal. Traditional circuits employ desliming or removing the 600 µm x 0 (28 mesh x 0) size fraction and feeding the cyclones +600 µm (+28 mesh) size coal. The feeding to zero concept recirculates 600 µm x 0 (28 mesh x 0) fines in the circuit. At the same time, a portion of the fine material is continuously withdrawn and recovered. This, in turn, prevents a fines buildup. This concept eliminates desliming screens and secondary fines circuitry for recovery of 600 x 150 µm (28 mesh x 100 mesh) coal. The result is a very simple circuit. Feeding to zero at Island Creek Island Creek Corp. was the first involved with the new concept in 1976. The company needed a temporary plant for the 9.5 mm x 0 (0.4 in. x 0) raw coal at its Pond Fork mine, near Madison, WV, while a full-scale plant was being designed and built. At that time, the Childress Corp., of Beckley, WV, became interested in the feeding to zero concept. Island Creek awarded a contract to Childress to build a single cyclone modular plant, incorporating this feeding to zero concept. The plant was erected in three months. The Pond Fork modular plant proved successful in attaining the desired feed rate of about 63.5 t/h (70 stph), while maintaining good separating efficiencies and low magnetite consumption rates. The 9.5 mm x 150 µm (0.4 in. x 100 mesh) clean coal was recovered and the 150 µm x 0 (100 mesh x 0) size was disposed of to waste. The full-scale plant was completed about two years later and the Pond Fork modular plant was moved to Holden, WV. There, it was incorporated into the Holden 29 preparation plant as a separate circuit for cleaning -25 mm (-1 in.) coal. In 1976, a similar plant was installed in Virginia by another company. These two plants are believed to be the first two operational plants in the United States incorporating the feeding to zero concept. Island Creek subsequently contracted with Childress for an identical plant at the Coal Mountain operation in West Virginia. The plant operated for three years before the mine was closed. The unit was then moved to the Spurlock mine near Martin, KY where it continues to operate. The successful operation of the Pond Fork and Coal Mountain plants before and after relocation proved both the performance and moveability of this type of circuit when constructed in a modular fashion. Since the first two plants were built, Island Creek has incorporated the feeding to zero circuit in nine additional plants. A grand total of 33 cyclones have been installed using this concept. One is the Providence mine, near Providence. Providence preparation plant Island Creek contracted with J.O. Lively Corp. of Glen White, WV in July 1978 for the construction of the Providence preparation plant. The plant began operation in February 1979. The construction period was about halved by building the plant with modular design concepts. Prefabricated sections, floors, and sides were brought in as units and then bolted in place. The Providence plant has a good track record of processing coal at a feed rate of 454 kt/h (500 stph). Feed coal to the plant has an average ash content of about 18% and sulfur content of about 4.5%. It contains about 22% refuse. The coal product has an average ash content of about 8% and sulfur content is about 3%. Raw West Kentucky No. 9 seam coal is conveyed from a box cut in the Providence mine to a rotary breaker. The breaker is fitted with 74 mm-diam (3 in.-diam) opening breaker plates. Therefore, it is well suited for removing trash, roof bolts, wood, and pyritic balls that are common in Illinois Basin coal. The -75 mm (-3 in.) coal is conveyed from the rotary breaker to

Jan 8, 1987

By Earl M. Frizzell, Ronald W. Utley

Introduction For the past several years the Bureau of Mines has undertaken research to develop alternative mine material haulage systems that will improve mine productivity, reduce haulage costs, increase mineral availability, and conserve energy. One basic concept being pursued is a means for crushing primary blasted rock to a size that can be reliably and economically moved on conveyors. During 1980, mine requirements for this equipment and the capability of existing technology to satisfy these requirements were assessed. The study continued into 1981 on the basis that satisfactory equipment for this purpose needed to be developed. The objective of the 1981 program was to perform an engineering design of such a system. A mine survey and equipment development study was conducted in cooperation with the open-pit mining industry by GATX through its subsidiaries, Fuller Co. (a crusher manufacturer) and GARD Inc. (GATX's research and development center), under contract to the USBM. Results of a mine survey in the copper, iron, and molybdenum industries indicated that a universal crusher system could be developed even though details might vary from mine to mine. The crushing characteristics, including tonnages desired, were similar in all surveyed mines. Most mines had similar views about the desirability and frequency of crusher movement. The perceived need for in-nit crushing varied between copper and iron mining. The copper mines felt a greater sense of urgency for introduction of such a system, probably because typically greater vertical haulage is found in copper mines than in the iron mines. All mine personnel surveyed were interested in portable crushers and almost universally preferred gyratory-type primary crushers. They preferred large crushers, citing inherent reliability and durability, and the machine's relative freedom from clogging. Large size minimizes the number of crushers and conveyors needed. Analysis of desired crusher system characteristics (Table 1) fixed the crusher size at 1.5 x 2.3 m (60 x 89 in.). The 1.5-m (60-in.) feed-opening dimension could accept the largest material normally fed to the crusher, and the 2.3-m (894n.) head diameter could fulfill the 3.63 kt/h (4,000 stph) capacity requirement. Selected System Description The comments and analyses discussed in the contract report led to the design and refinement of a movable crusher system. This system represents the consensus of more than 100 mine workers and almost 50 construction and engineering company personnel. It is supported by more than 50 years of experience in crusher manufacturing. Although many alternatives are available for any given system, and selections are likely to be dictated by varying site conditions, the selected system is believed to be appropriate for most projected requirements. Final design would be dictated by mine operators during evaluation for approved projects. Detail design of the feed and discharge systems were not included in the study because they are mine specific. The basic system (Fig. 1) consists of a 1.5 x 2.3-m (60 x 89-in.) gyratory crusher on a structural steel frame. The frame is used as an operating platform for the crusher and as a carriage to move the crusher. The control tower includes a crusher lubrication room, a hydraulic equipment room, a switch gear room, a room for the motor control center, and a control room for operating the crusher and maintaining the equipment. The auxiliary system consists of a hydraulic rock hammer and pedestal crane with 74-t (80-st) and 14-t (15-st) hooks. Figure 1 also shows stairs, railings, and a work platform. Feed and discharge arrangements are shown on Fig. 2. The system shown is for mildclimate applications. Additional enclosure and heating would be needed for extremely cold weather conditions. Crusher A 1.5 x 2.3-m (60 x 89-in.) gyra¬tory crusher was selected for this application. This size can handle the typical throughput of 3-3.63 kt/h (3,500-4,000 stph) desired by the mines and the 1.3-m (50-in.) material to be crushed without difficulty. The crusher is the heaviest

Jan 4, 1983

By A. L. de Vegt

For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps: 1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (H2S). The H2S reacts with the dissolved metals to form insoluble metal sulfide precipitates. 2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m /d. A pilot plant started operation in November 1995 at Kennecott's Bingham Canyon Utah copper mine to develop the processes for metal and sulfate removal from groundwater and selective copper recovery from leach water. The principle of the biotechnological methods, full scale experience, and an overview of the test program at the copper mine are presented.

Jan 1, 1997

By C. E. Seaman, H. Jiang, S. Klima, T. W. Beck, Y. Zheng

Respirable coal dust has been long recognized as a leading cause of multiple lung diseases. Efforts aimed at reducing dust concentration in underground mines have been made, but increases in coal workers’ pneumoconiosis incidence rates over the last 20 years among U.S. miners are concerning. Dust deposition and water spray suppression are two types of dust removal mechanisms in underground mining activities. In this study, laboratory tests were conducted to investigate the respirable dust decay characteristics during deposition and suppression processes in a confined dust chamber. Dust concentration and size distribution were monitored continuously throughout each 60-minute test. A number-basis particle size distribution was used for analysis to capture the changes of smaller size fractions within the investigated dust sample. This study found that around 62.1% of respirable dust particles were deposited at the end of the deposition test. In addition, the final deposition rate for very fine particles can be less than 20%. The results from the suppression test indicate that larger particles were removed quickly; however, sub-micron particles remain suspended through the 60- minute water spray, and particles under 0.5 µm can be considered irremovable dust under single-spray operation conditions. This study also observed the resuspension of a significant amount of sub-micron particles by the water spray. The results of this study provide basic information for improving dust control strategies and can be utilized to improve the water spray performance for reducing airborne dust levels.

Mar 2, 2022

By C. Newman

"As underground mining continues to operate at deeper depths and in more complex multiple seam mining geometries there has been an increased demand for higher design standards in ground control safety and stability within the mining industry. For the past 20 years, NIOSH has developed and validated a number of software tools to aid in the development of safer mining environments with respect to improved roof support performance, pillar stability in longwall and room and pillar mines, formation characterization, the prediction of roof conditions, etc. These tools are available, free of charge, to the mining industry as stand-alone software packages. As cloud computing gains momentum, there is a definite need to develop internet based applications for mine design that would be easily accessible to any user at any time, including underground where permitted. This paper introduces a new web-based product which will allow for faster and easier access to existing ground control designs, on-the-fly calculations in the field as needed, and instant online collaboration between operations personnel and planning engineers. It is expected that the industry will rapidly embrace this product and, as it is common with all new innovative technologies, it will be a new paradigm for mining engineering computer applications. INTRODUCTION Since its release to the public in the late 1980's, the World Wide Web has drastically changed from a collection of static HTML web pages to a dynamic vehicle driving e-commerce, collaborative working relationships, and the mass distribution of information and media (Offutt, 2002). Recent developments in Internet capabilities, such as Cloud Computing and Software as a Service, have begun a migration away from desktop-based software in adoption of the web application (Hayes, 2008). Web applications, or web apps, are designed on the client-server architecture paradigm in which the client, or user, can interact with an application through web browsers without disrupting or installing software on potentially thousands of client computers (Nations, 2015). Currently, web-based software applications are being utilized in all business sectors and markets from commerce, finance, media, and even engineering. In fact, the Alabama Department of Transportation has developed a web-based geotechnical geographical information system (GeoGIS) for the management of and access to geotechnical and subsurface data for transportation projects across the state (Graettinger, et al., 2001). Similarly, Dyno Noble has developed a service application for explosive engineers. The Explosives Engineers' Guide application equips users with a full range of product information as well as on-demand blasting calculations for powder factor, airblast prediction, ground vibration, etc. Through the incorporation of a web server, one is able to utilize the functionality of the desktop-based software through a web browser located on any personal computer, tablet, or Smartphone (Vaughan-Nichols, 2002)."

Jan 1, 2016