Search Documents

By Hyung Jeek Kim, Jongmin Joo, Jonguk Kim, Jai-Woon Moon, Kyeong-Yong Lee

"Co-rich ferromanganese crusts (Fe-Mn crusts) distributed on seamounts in the western Pacific are potential economic resources for cobalt, nickel, platinum, and other rare metals in the future. Evaluation and selection of a mining site can be established based on abundance and grade of Fe-Mn crusts in the site as well as topography that should be smooth enough for mining operations. Therefore, acquisition of shipboard echo-sounding and acoustic backscatter data are prerequisite to the selection of potential mine sites in addition to visual and sampling operations. Acoustic backscatter data can be used to locate crust-covered areas on a regional scale with the understanding of acoustic properties of crust through its correlation with visual and sampling data.During an expedition that took place from January to March 2014, KIOST collected geophysical and geologic data to assess the resource potential for Fe-Mn crusts on three seamounts (guyots) in the Western Pacific. In OSM11, one of the three surveyed seamounts, three camera tows were performed to observe the distribution of Fe-Mn crusts on the summit and slopes of the seamount. Although sediments of various thicknesses generally cover most of summit region of OSM11, several regions with high backscatter signals occur on the periphery of the summit. The occurrence of Fe-Mn crusts, observed during the camera tows, on those high backscattered regions suggests that the backscatter signals of shipboard multi-beam sonar can reflect changes in the geology of the seafloor from sediment layer to Fe-Mn crust deposits. The Fe-Mn crust deposited around the summit region is worthy of notice because of its topographic characteristics, including shallow depth, flat or gentle inclined surface, and smooth relief, which are more suitable for mining operation compared to the flanks of seamount."

Sep 1, 2014

By S. Al-Thyabat

Conditioning of flotation feed is an important prerequisite for efficient flotation. This process depends on parameters such as conditioning time, slurry concentration and slurry pH. The objective of this paper is to optimize the conditioning process for the flotation feed. This was achieved by first conducting preliminary experiments at constant slurry pH to determine the significant ranges of slurry concentration and conditioning time. Then, factorial experimental design (32 experiments) was used to investigate the significance of the above parameters and their interactions on flotation recovery and grade. Statistical analyses using ANOVA approach showed that flotation recovery (R) and concentrate grade (g) were affected by feed conditioning. It was found that concentrate grade was linearly proportional to the slurry concentration and conditioning time, while flotation recovery was exponentially proportional to the conditioning parameters. A contour plot of the flotation response (recovery and grade) against conditioning parameters showed that the optimum operating parameters for flotation feed conditioning was a conditioning time of 1.5 to 2 minutes and a slurry conentration of 55% to 60%.

Jan 1, 2008

By Richard Hanke

Tunnel construction on the Brightwater Conveyance System?s East and Central contracts required ground modifications of the existing site soils, comprised of sandy alluvium to very dense glacial till, to assist with both hand-mined and TBM tunneling operations at vertical access shafts. The ground modification program was completed with a modified double fluid jet grouting system to construct continuous overlapping soilcrete columns to depths up to 94-ft below existing grade. This paper presents the sequence and methodology for the ground modification work and capabilities of jet grouting for structural support and groundwater control in the challenging soil profile present at the Brightwater Conveyance System Project.

Jan 1, 2008

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

By Jochen Belz, Allan Henneker, Nod Clarke-Hackston

For the construction of tunnels and other underground structures, extraction of the exact amount of material is of paramount importance both economically and for engineering purposes. In the Sequential Support Method (NATM) immediate (sequential)and smooth support by means of shotcrete, steel arches, lattice girders and rockbolts, either singly or in combination are used; cutting of the precise (albeit sometimes of complex geometry) profile is an integral part of the method. In order to save unnecessary excavation and provide better information to the machine operator, VMT GmbH has developed a system to support precise excavation of the tunnel profile when using road headers or other partial face cutting machines. This paper outlines the principles of this system with examples from Australia, Ger-many, Sweden and Spain and will cite examples of typical savings achieved.

Jan 1, 2007

1. Paper1?Identification and enumeration of asbestos fibers in the mining environment: mission and modification to the federal asbestos standard Arthur M. Langer Asbestos-related disease is increased with cumulative exposure (the concentration of asbestos in the air and duration of exposure). The maximum duration is assumed to be a working lifetime so federal agencies control cumulative exposure by limiting the airborne concentration of asbestos fibers equal to or greater than 5 lm in length. Air samples are collected in the environment of interest by entraining the airborne particulates including fibers on membrane filters and then counting the number of fibers using phase-contrast light microscopy. In addition to length, the fibers must have a length to width ratio of at least 3 to 1. This ratio is also referred to as the aspect ratio. Some counting strategies placed an upper limit on the fiber width restricting the counting to respirable fibers. Airborne asbestos is controlled by monitoring a sub-population of the airborne asbestos. No asbestos fibers shorter than 5 lm or fibers of any length having widths less than the resolution of the light optical method are counted. In the non-occupational environment, the Environmental Protection Agency requires the use of analytical transmission electron microscopy and fibers and counting fibers with lengths of 0.5 lm or greater and aspect ratios of 5 to 1 or greater are counted. The permissible exposure limit for asbestos has been reduced by more than 120-fold since 1969, when the standard was 12 fiber/ml and the current monitoring methodology was developed. The manufacturing and mining worksites are regulated by two different federal agencies and the asbestos exposure limit was higher in the mining environment until recently (Mine Safety and Health Administration 30 CFR Part 56, 57, and 7, Federal Registry, February 29, 2008). Currently the permissible exposure limit (PEL) is the same in both types of workplace and it is 0.1 fibers per milliliter (fiber/ml) over an 8-h shift as a time-weighted average (TWA). A milliliter (ml) is equivalent to a cubic centimeter (cc) and sometimes this standard is reported as 0.1 f/cc. As the phase-contrast methodology was used to monitor lower exposures and environments, other fibrous mineral particulates were incorrectly characterized as asbestos. These occurred in talc deposits and taconite ores from the Eastern Mesabi Range.

Jan 1, 2008

By K. Boakye

This paper presents the results of a review of historic blast design practices at the Dragon Products Company, LLC (Dragon) Quarry Operation, along with the results of two different blast design vibration monitoring programs. A blast pattern design modification was initiated to determine if production volume per shot could be increased and highwall instability could be decreased. A vibration monitoring program was undertaken to investigate peak particle velocity (PPV) and relate the data to the blastability of the jointed onsite rock mass, utilizing the relationship between PPV and dynamic stress and strain. The Dragon Quarry Operation has historically used a 6-in. diameter, 14-ft by 14-ft production blast pattern, with blast holes loaded manually using cartridge style explosive products. In 2011, Quarry Operations introduced a 6-in diameter, 16-ft by 16-ft production blasting pattern, using pre-mixed, truck-loaded, bulk emulsion/ammonium nitrate/fuel oil (ANFO) blends. This paper summarizes the results of the blast design modifications, the results of the vibration monitoring data, and describes how production blasting and excavation at the Dragon Quarry has benefited from such modifications.

Feb 27, 2013

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

By Adriaan de Villiers

Many conventional structural analysis and design methods in current use are not appropriate for the mining industry. Two major reasons for this are that: • The economic life of a particular mine is limited, and • Much of the equipment and machinery used by the mining industry operates at relatively low speeds. Both of these factors can have significant cost implications if they are not properly accounted for during plant design. In particular, the often used practice of mitigating excessive vibration by adding mass to machinery supports is not only expensive but may worsen the vibration effects. Some of these problems, such as increased wear and tear, are not always easy to trace back to inappropriate design. This article focuses on vibration related issues and demonstrates that the mining sector has unique problems requiring unique solutions. Vibration: the basics Historic developments leading to current vibration design practices provide the key to why such practices are often inappropriate for the mining industry. To understand this, it is necessary to introduce some basic vibration theory. Consider a simply supported beam or foundation on which a vibrating machine is mounted. For analysis of the system's dynamic response, it may be viewed as a mass attached to a spring and a damper, such as the shock absorber of a car.

Jan 1, 1992

By E. Lammer

"Underground mining processes are dangerous. The design of mining equipment, which is able to cope with the hostile underground environment, is a challenge for all machine manufacturers. Presupposition for realizing the vision of SANDVIK for zero harm for working with SANDVIK equipment is the installation of the appropriate processes. Into the product engineering and product development processes of Sandvik Mining and Construction, a specific "Product Safety Process" has been integrated, where all safety related activities like identification of all life cycle hazards, risk management and safety verification / validation are planned, performed and documented. Product safety shall be „designed into" the products. Therefore, specific research activities have been started, to address the safety and health related topics for the development and for the engineering of SANDVIK mining machines."

Jan 1, 2011

The US Constitution provides for regulation by the states for protecting the public's safety, health, and welfare. Hence, in the eyes of the law of all states today, this is the sole justification for registration of professional engineers. Wyoming was the first state to register professional engineers in 1907, to correct abuses of incompetent or fraudulent practices in surveying and real estate. Public safety and health are most directly affected by civil, electrical, and mechanical engineering. Other branches of engineering have a profound effect on the public welfare, including investors, and safety and health of employees. No arguments, pro or con, are valid except in relation to the registration laws of various states. Code of Ethics Few would argue the desirability of requiring conformance with a code of ethics. A major problem lies in enforcing compliance, since protecting the public demands a high standard of competence, yet assessing competence gets confused with restraint of trade. Bidding engineering work on price competition can lead to pressure to cut corners on engineering quality, and was therefore discouraged by codes of ethics. The Supreme Court, in a suit against the National Society of Professional Engineers (NSPE), barred any engineering society from such bidding restriction. It has, however, upheld the right of states to impose codes of acceptable practice as part of registration laws. For example, Texas Canon I reads, "The engineer's paramount professional responsibility should be the safety, health, and welfare of the general public." Anything less makes the code practically meaningless, but there are potential conflicts of interest in many engineering organizations. How can conflicts be handled? Any corporation could improve its public image by adopting a policy that each employed PE should, without fear of recrimination, record in writing over his seal any problem or flaw in any design that comes to his attention. The policy should further require that his superior provide him a written reply pointing out that the "flaw" is accepted as requiring correction or as a calculated risk, or overruled as erroneous or as a difference of opinion. Errors in calculation of judgment are inevitable. Despite this, there are limits to how much time and money should be spent to eliminate them. It is difficult, however, to see any excuse for failure to conscientiously evaluate the opinion of a PE. This may be an impossible ideal, but how else can the profession or the industry have credibility? The National Council of Engineering Examiners (NCEE) has a code of ethics one presumably subscribes to by signing an application to write a Principles and Practices examination. However, NCEE has none of the power of enforcement that is available through state boards of registration. Registration Qualifications Qualifications are set by the laws of the states. In general, they require passage of an eight-hour examination in fundamentals, preferably at graduation, and, later, one in principles and practices. The examinations are compiled and distributed by NCEE. This system provides for a high degree of uniformity and reciprocity. States set the education and experience levels (typically four years after graduation) required by those desiring to write the principles and practices examination. Examinations The principles and practices examination calls for answering eight of 20 equal weight questions; one on engineering economics, 19 on engineering. Economics may enter into engineering questions, but only provided the question is not answerable by an economist without engineering training. In preparing examinations, NCEE strives to use questions that require some judgment and can be more effectively answered by someone with four years experience beyond college. The aim is to assess entry-level professional

Jan 2, 1984

By D. Brady

There are many examples, historical and recent, from the underground coal mining industry where during emergency response the response and ultimately the outcomes, could have been significantly improved if adequate systems had been in place for the collection and management of relevant information preceding the incident, the acquisition of information during the incident and the use of the information for risk mitigation and decision making purposes. The subject and process of knowledge management is possibly the most critical for would be rescuers of endangered coal mine workers, as it has been demonstrated at numerous coal mine incidents that a lack of or mismanagement of crucial information can be fatal for both the rescuer and/or the endangered coal mine worker. This paper will underline the scope and importance of robust knowledge management systems for emergency response within the underground coal mining industry and the process by which it is being achieved within the Queensland Mines Rescue Service and the NSW Mines Rescue Service.

Jan 1, 2012

By Jeffrey D. Thatcher, Debra W. Struhsacker

With the burgeoning development of precious metals heap leach mining projects throughout the country regulatory agencies are beginning to take a closer look at the short-and long-term environmental consequences of heap leach mining. This increase in regulatory review is occurring on federal, state and local levels, and is affecting both large- and small-scale mining developments. Small-scale mining developments are receiving especially critical regulatory scrutiny because in the eyes of some regulatory agencies, small developers lack the credibility automatically accorded to major mining companies. This is due in part to a bad image of small miners based upon past environmental problems and permit violations caused by a few, small operators. The proponent of a small mining development thus faces special problems during the project permitting process, and must convince the regulatory authorities of his company's ability and commitment to plan, develop, and decommission a mining operation in compliance with environmental regulations. Not only must the small developer have a thorough understanding of the regulatory requirements affecting his project, he must also devote considerable effort to careful internal planning in order to produce a well organized approach to project permitting. The importance of proper planning cannot be overstated. Project planning is key to convincing the regulatory agencies that the small miner is capable of developing a viable project. More- over, the economics of a small mining project demand permit acquisition at modest cost and in a timely fashion. A well planned permitting effort will thus ensure that permits are received within budget and on schedule. This paper will review the federal, state, and local permitting requirements for heap leach projects, and the variability of these requirements from state to state. The environmental assessment process for projects developed on public lands, and the acquisition of zero- discharge water quality permits, air quality permits, and local special use permits as they apply to small mining developments will be discussed. The paper will conclude with a review of project decommissioning and cyanide neutralization requirements and their implications for small-scale heap leach projects.

Jan 1, 1987

By R. K. Singhal, H. Sahay

Introduction In terms of the world's recoverable coal reserves, Canada ranks 10th, providing 0.6% of the world's total. The US is first with 27.8% and the Soviet Union follows with 24.1%. Figure 1 shows the principal coal mines in Canada. Several provinces contain substantial coal deposits, but the largest deposits are found in the western provinces of Alberta, British Columbia, and Saskatchewan. Conservatively, 90% of the lignitic, 80% of high volatile bituminous, and nearly 100% of subbituminous, and low and medium volatile bituminous coals are located in these three provinces. During the past decade, Canadian coal production of all types increased from 18.8 Mt (2 million st) in 1972, to 25 Mt (28 million st) in 1975, to 61 Mt (66 million st) in 1984. About 38 Mt (43 million st) of this output was classified at thermal and 23 Mt (25 million st) as coking and metallurgical coal (Table 1). The three western provinces currently produce 57 Mt (62 million st) of coal - 95% of Canada's total. The remaining 3.6 Mt (4 million st) (5%) is produced in Nova Scotia and New Brunswick on the east coast. The majority of western coal (98%) is produced by surface mining methods. On the east coast, though, mining is predominantly underground and only 15% is produced on the surface. In 1985, Canada exported close to 28 Mt (30 million st) of metallurgical coal and thermal coal. During the same period, 15 Mt (16 million st) of coal were imported, mostly from western US for use in Ontario and Quebec. Almost 60% of the imported coal was used for thermal applications. The remaining 40% was metallurgical coal for the steel industry. It is generally cheaper to import coal into central and eastern Canada from the eastern US to augment local supplies rather than from western Canada. This is mainly because of high transportation costs. Mining methods The suitability of mining methods in a particular area depends largely on the geological setting. Geology, therefore, simplifies or adds complexities to mining operations, directly affecting the economics. It also influences the flexibility required from the min-

Jan 9, 1986

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

By V. Arslan

The primary advantage of using oxalic acid is in the formation during leaching of soluble complexes that are both photo-chemically and microbiologically degradable. In this study, chemical leaching and bioleaching methods were used for quartz sand. Using the ANOVA-Yates test technique, the effects of solids rate, temperature and oxalic acid rate were investigated using chemical leaching experiments. Solids rate and temperature were effective parameters on the chemical leaching. After the tests, the removal of Fe2O3 increased to 97.02%. Finally, the iron content decreased from 0.315% Fe2O3 to 0.0094% Fe2O3 in the leached quartz sand. The effect of pulp density was investigated on the bioleaching experiments. The bioleaching of iron oxides by Aspergillus niger resulted in removal of 47.70% of the total iron in the quartz sand, and suggested that this strain has not a good ability to remove iron impurities from quartz sand in comparison with chemical leaching. The iron content decreased from 0.315% Fe2O3 to 0.164% Fe2O3 in the bioleached quartz sand.

Jan 1, 2009

By W. K. Hitchcock

Hydrogen is regarded as being a high temperature indicator of spontaneous combustion. It is currently used in underground coal mines to detect advanced heating?s. Previous work has mostly consisted of small scale tests with high air flow to mass ratios. A large-scale test rig has been used to investigate the gas indicators of coal self-heating. In particular, the relationship of gas evolution, the location of its evolution and the temperature at which it is evolved has been examined. It has been found that there are two distinct zones of hydrogen production: one at the hot spot and the other in an oxygen deficient moist zone downstream from the hot spot which is at a relatively low temperature of approximately 100°C. This has implications for the interpretation of mine atmospheres.

Jan 1, 2009

By Tim O’Neil

Tire companies have historically used the mining industry as a platform to launch new technologies. And the mining industry has been receptive to that. So, while developing its Two Piece Assembly, Goodyear noted a number of trends in the mining industry: •The global market sophistication of equipment and operations requires the packaging of products and services to provide the best return on investment. •Industry consolidation and growth have resulted in fewer, more powerful mining houses, leveraging purchasing power in the marketplace. •User productivity demands continue to drive original equipment manufacturers to develop higher pay-load equipment. •Technology needs include improved ergonomics, to reduce fatigue and increase operator productivity. •Increased laws and environmental regulation prohibit on-site whole tire disposal practices.

Jan 1, 2003