Search Documents

Energold Drilling Corp. is a leading specialty drilling company servicing the mineral and energy sectors in the Americas, Africa and Asia. Energold specializes in mineral exploration in remote locations with limited infrastructure. Such locations require the smallest footprint possible going in, leaving as little or no evidence on their way out. Energold?s rigs can be transported by helicopter or manually on footpaths as narrow as 1 m (3.3 ft). They set up quickly and then are struck and packed out, with any sign of their presence quickly disappearing behind them. Energold has teamed up with Atlas Copco and its team of engineers in North Bay, Ontario to design small rigs capable of drilling to a variety of depths, as required for each project.

Jan 1, 2013

By John Hayden

The nation runs on energy. It is essential for the economic growth and national security of the United States that the nation has an adequate, sustainable, environmentally acceptable and economically viable balanced supply of energy sources, (e.g., coal, petroleum, nuclear, natural gas, solar, wind, geothermal, biomass, hydroelectric power). Therefore, the allocation of mineral raw materials to the energy-producing sector of the economy must be a top priority that requires the total demand for energy-related materials be judged in terms of domestic supply (Fig. 1).

Jan 1, 2012

In the late 1980s and into the 1990s, the Mountain Pass Mine in California produced about 40 percent of the world?s rare earth elements. At the height of this production, the facility produced up to 54 L/s (850 gpm) of saltwater that was piped to offshore holding ponds where the water was evaporated. In 1998, following a series of waste water pipeline breaches, separations activities were suspended, reducing the Mountain Pass site to just the openpit mine and mill. The environmental concerns were addressed and the affected areas have since been remediated. However, in the years following the breaches, 97 percent of the world?s production of rare earth elements moved to China. By 2011, Molycorp, and the Mountain Pass Mine, had rebounded from the difficult times and were once again in a position to become a significant player in the rare earth industry.

Jan 1, 2011

By Qinbo Cao, Qianshan Peng, Heng Zou, Xingcai Yu

Rutile ore is an important resource for the production of titanium products, and flotation is an efficient method to enrich rutile from its deposits. Motivated by strong commercial demand for titanium metal and alloys, substantial efforts have been made to improve the flotation efficiency of rutile. Styryl phosphonic acid (SPA) and salicyl hydroxamic acid (SHA) are commonly used as collectors for rutile flotation, and lead (Pb) ions can be used as activators for rutile flotation with SPA or SHA. Xanthates have a price advantage over SPA and SHA for the flotation of sulfides as SPA and SHA prices are higher than xanthate prices. In this work, we found that when rutile is activated by lead ions, amyl xanthate is an efficient collector for rutile flotation at pH 8. A slightly basic slurry can be readily obtained. Moreover, the price of amyl xanthate is lower than that of SPA or SHA. In this regard, this flotation strategy has the potential to be used in industry. Furthermore, the adsorption features of amyl xanthate on the Pb-activated rutile surface was investigated by experimental methods, which provides insight into the role of lead ions in rutile flotation.

By Adrianus Halim, Jenni Hooli, Bartłomiej Skawina, Fredrik Sundqvist

Transitioning from diesel-powered loading and hauling machinery to battery-electric vehicles (BEVs) responds to the need for deepening underground mines as regulations become tighter. When using BEVs, exhaust gases and diesel particulate matter (DPM) emissions can be eliminated, and the energy required for the machines is used more effectively. Unlike their diesel counterparts, which are refueled, BEV loading and hauling machines — specifically, load haul dump (LHD) machines — can use battery swapping. This brings additional aspects to the operation that need to be considered, which have not yet been studied extensively. This study used discrete event simulation (DES) to analyze how the different numbers of BEV LHDs affect queueing and productivity when using different numbers of batteries and different swapping times in an underground block cave mine. The results identified the formation of working groups, where the machines swapped their batteries concurrently within each group, and their relation to the queueing time. Additionally, the minimum number of batteries per machine was identified to maximize productivity while minimizing queueing time. This study demonstrates DES as a powerful tool to assess and analyze conceptual systems and identify their underlying structures, which can enhance the deployment of BEV LHDs in underground block cave mine operations.

Apr 1, 2025

By S. S. Sephton

Sintering as applied to agglomeration of ferrous fines has shown little growth in the United States in recent years. The general concensus was that most of the existing facilities would remain in production at a reduced tonnage to dispose of and recover solid waste from steel plants. Further growth for ferrous sintering technology was not in sight in the United States and in the early sixties expansion came to a virtual standstill, however, we witnessed a rapid emergence of a tremendous pelletizing industry. On other continents, due to different raw materials supply and capital structure, sintering technology continued to grow, with a more cautious development of pelletizing installations. In the U.S. the diminishing supply of good quality, high grade coarse ore resulted in eventual disappearance of high grade ore fines for sintering. The finely divided concentrates produced from lower grade ores were not amenable to this type of agglomeration, but were more suitable for pelletizing. Furthermore, pellets seemed to possess all the features of an ideal blast furnace feed; namely pellets are free flowing, uniform in size, strong, with extremely uniform chemical composition and good reducibility. Importance and demand for such well stabilized furnace feed further increased as size of newly installed blast furnaces continued to grow. The in- creasing demand for a uniform, stabilized burden coincided with the effort to produce a fully beneficiated burden for smelting, thus reverting the blast furnace to its primary function of smelting.

Jan 1, 1973

By John Hickey

Management teams at mining companies begin to ask themselves whether to take a company public and, if so, how to do it as they approach the normal threshold for going public in terms of revenue and operating performance. Today, the expense of going public generally suggests the company has at least $20 million in annual revenue and at least $2 million in cash. The revenue number can be lower for mining companies with large reserves. In order to properly attract the investing public, the company must also be operationally strong with robust prospects. The company should have a strong management team and a consistent history of double-digit growth that will continue into the foreseeable future. Assuming the thresholds are met, a company?s management needs to weigh the pros and cons of going public.

Jan 1, 2012

By Yong Pan, SRIVATSAN JAYARAMAN SRIDHARAN, Purushotham Tukkaraja

The block cave mining method poses unique ventilation challenges compared to other underground metal mining methods. This research study focuses on assessing the airflow behavior in regulated airflow distribution systems by developing a 1:100 scaled block cave experimental model and a numerical model. This study also investigated gas flow behavior under various airflow conditions. Based on our findings, we observed that reduction in particle size and porosity of caved materials, decrease in cave footprint, and closure of undercut drifts would increase cave airflow resistance. The increased airflow is found to be beneficial for gas dilution regardless of its source locations, while the regulated airflow distribution system might deteriorate the gas dilution situation when the source is located in the extraction drifts.

Sep 1, 2022

By E. R. Hoskins

The Gulf Coast States ranging from South Texas to Alabama contain vast resources of lignite ranging in energy content from about 4000 to 7000 Btu/lb (as-received) with sulfur content ranging from about 0.5 to 2 percent. Currently, the strip mining rate is about 35 million tons per year in Texas and essentially zero in the other Gulf Coast states. Estimates of future mining rates are as high as 310 million tons per year by the year 2000 with 240 being in Texas. In this paper, we examine the life cycle of the surface mineable lignice based on the most recent estimates of surface mine recoverable resources with two scenarios. The first indicates that a 310 million tpy rate could be sustained for only 15 years while the second scenario suggests that the 310 million tpy could be sustained for 25 to 30 years. If lignite resources are required beyond those that are surface mineable, the deep basin lignite will be developed. Five strategies for developing deep basin lignite are discussed.

Jan 1, 1983

By Charles B. Dugger

Sacrificial linings for grinding mills have been a necessary state of the art of mineral dressing since the inception of comminution. Long recognized as the final link in energy transmission from power line to ore, mill liners as a scientific endeavor have not expanded as rapidly as other branches of mineral dressing engineering. Several reasons for this technological lag are apparent. Typically in the past, labor intensive foundries were freely located geographically, at a time when transportation charges made up a significant portion of the casting cost. Alloying agents had not gained their current level of sophistication and were relatively inexpensive in the quantities required. Precise foundry controls were not economically justified, or totally understood. Coincidental to these elements, liner consumption per unit processed did not categorically contribute as a major cost item to the mill operator. Grinding equipment was small, and many times lining life exceeded that of the promoter. These unique conditions no longer exist. Ore dressing equipment has grown to meet modern mining demands. Larger processing facilities, utilizing fewer pieces of equipment, have replaced operations of the past. Emphasis today and tomorrow is on larger and larger equipment, with an eye on lower and lower unit processing costs.

Jan 1, 1979

By Robert M. Stevens

INTRODUCTION Truck haulage of muck in underground mining operations has been in use around the world for many years. From the late 1.950s into the early 1970s, haulage by means of load-haul-dump (LHD) units challenged haulage by means of trucks, and, to a large degree, LHD units dominated the trackless concept of moving mate¬rial underground. However, beginning in 1975, the emphasis began to shift back to the use of trucks, with LHD units assuming the secondary role of loading the trucks. Over the years, several manufacturers have been offering trucks with capacities ranging from 4.5 to 45.4 t (5 to 50 st) and with features that specifically address the constraints of underground operation. TRUCK TYPES Three different types of trucks are available for use underground, namely the tip dumpers, telescoping dumpers, and push-plate dumpers. The following para¬graphs describe each of these three types. Tip Dumpers Tip dumpers are designed to lift the truck box, using gravity to dump the load out the rear of the box. The primary application of these trucks is in the haulage of muck to the surface. However, these trucks also may be utilized underground, if a chamber is provided to accommodate the raised truck box at the dumping point. Fig. 1 illustrates a four-wheel drive truck with a 10.0-t (11-st) capacity; this truck is only 1.9 m (6.25 ft) wide and is designed specifically to follow narrow and winding vein courses. Fig. 2 illustrates a two-wheel drive tip dumper with a 24.5-t (27-st) capacity; this truck operates on 12% grades with firm dry surfaces and in modes both loaded-up and loaded¬down. Telescoping Dumpers Telescoping dumpers specifically address the constraints imposed by low back heights, and they represent an optimization of compressed envelope size with maximum payload capacity. Figs. 3 and 4 illus¬trate a typical telescoping dumper with a capacity of 18.1 t (20 st). Fig. 3 shows the box in position for carrying the load, and Fig. 4 shows the same truck with the box in the full-dumping position. Fig. 5 illustrates the loading and dumping cycles. Fig. 6 illustrates an approximation of how an LHD unit with an eject-o-dump (EOD) bucket would be used to load over the rear of this type of truck. Fig. 6 shows a low-profile telescoping truck in the first stage of loading, with a 6.8-t (7.5-st) LHD unit equipped with an EOD bucket. A loader with a smaller capacity and a narrower bucket would allow the bucket to fit inside the truck box and would achieve an even lower loading height than that illustrated. Gen erally, an LHD unit equipped with an EOD bucket and teamed with a telescoping dump truck can be used with a lower back height than could any other front-end loader and truck team. Push-Plate Dumpers Push-plate dumpers are similar to telescoping Bump¬ers, except that they do not have the two-stage box. Instead, push-plate dumpers utilize a single push plate to discharge the load out the rear of the box. Gen erally, these units are limited to payload capacities of about 9 t (10 st). Fig. 7 illustrates a typical push-plate dumper.

Jan 1, 1982

By William Gleason

"More than 6,300 people converged on the Colorado Convention Center for the 2017 SME Annual Conference and Expo and 119th National Western Mining Conference in Denver, CO on Feb. 19-22. Many of them crammed in to hear Douglas Silver deliver the keynote address to the conference.Silver is a portfolio manager for Orion Mine Finance, a private-equity fund focused on providing funding to advanced-stage base and precious metal projects and is one of the most respected voices in the field of mineral economics. Prior to joining Orion, he served as chief executive officer and chairman of International Royalty Corp., a global mineral royalty company, which he founded in 2003 and sold in 2011.Those who were hoping that Silver would deliver at least a bit of optimism during his 90-minute presentation got what they came for from the talk titled, “When are commodity prices going to rebound?”It marked the second time Silver has presented the keynote address to SME, the first was in 2008 and was delivered during the height of mining’s super cycle (ME, June 2008). In his 2017 address, Silver looked back on the previous 10 years and the massive contraction of the global economy that resulted from the great recession that began near the end of 2008.It has been a challenging time for the mining industry. About US$1.4 trillion was lost in the global mining stocks from 2011 to Jan. 6, 2016. Major mining companies exceeded $60 billion in write downs between 2012 and 2013 and investors lost confidence in the sector, putting the global mining industry into a bear market that has taken mining equities to historic lows.However, that was then and this is now.Using numerous examples, including rising commodity prices, a steady decline in the U.S. unemployment rate, increases in discretionary income and the Dow Jones Industrial Average, which topped the 20,000 mark for the first time ever in February, Silver theorized the current down cycle is near its end and the demand for metals and other commodities will see a sharp increase by 2025. He also noted that investors are beginning to rotate back into mining equities."

Apr 1, 2017

By Wei Victor Liu, Na Zhang, Chengkai Fan, Bei Jiang

This study used artificial neural networks (ANNs) coupled with Gaussian mixture modeling (GMM) to analyze truck haulage data from openpit mines. The proposed weighted ensemble models performed better than benchmark models in predicting truck productivity, providing a new means of solving complex data and improving mine planning and decision-making.

Jun 1, 2023

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means of controlling gases and dust. In order to study longwall ventilation in a controlled environment, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers built a unique physical model called the longwall instrumented aerodynamic model (LIAM). The LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel. It has an 8.94 by 4.88 m (29 by 16 ft) footprint with a simulated face length of 220 m (720 ft) in full scale. LIAM is built with critical details of the face, gob and mining machinery, and scaled to preserve the physical and dynamic similitude. This paper discusses the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By Richard H. T. Garnett

In 1900, placer gold was discovered on the beach of Nome, AK on the southern coastline of Alaska's Seward Peninsula (Garnett, 1991). The site is about 800 km (500 miles) from Anchorage. Nome is connected to Anchorage only by air (daily) and by sea (summer). Total onshore placer gold production from Nome's immediate vicinity was more than 155.5 t (5 million oz). Alaska Gold Co, has continued to produce gold onshore with, until recently, two bucketladder dredges, each of 255-L (9-cu ft) bucket capacity. Small-scale marine dredging for gold has been at- tempted several times this century (Garnett, 1991). Western Gold Exploration and Mining Co. Ltd. Partnership (WestGold) is the only company to have been successful in achieving a significant offshore production. The Nome bucketladder-dredging operation from 1986 to 1990 constituted a unique marine-mining experience in the United States. \Inspiration Gold Inc., WestGold's predecessor, acquired six offshore leases in 1985. The total lease area of 87 km2 (21,551 acres) extended from the coastline to the 4.8-km (3-mile) offshore limit (Fig. 1). Those leases al- ready had been partially explored. Drilling was conducted off the shorefast winter sea ice. Therefore, it was rarely more than 1.6 km (1 mile) from the shore or in water deeper than about 9 m (30 ft). In 1985, estimated reserves comprised of a 5-m (17-ft) vertical thickness of sediments below 6.3 m (20 ft) of water. This meant a mean digging depth below the mean sea level (msl) of 11.3 m (37 ft). It was thought that the offshore Nome deposit possessed a feature that is common with many terrestrial gold placers - the secret of profitable exploitation of the marine deposit lay in maximizing the dredge throughput to minimize the unit costs. The inability of the project to withstand the prohibitively high cost of a new dredge was recognized. So Inspiration Gold purchased a used unit. This was the world's largest ocean- going bucketladder dredge (Fig. 2). Binzn was an 850-L (30 cu ft) bucket capacity dredge that was lying idle in Singapore. Originally constructed in the Jurong shipyard of Singapore in 1979, Bima was designed by Mining and Transport Engineering, a subsidiary of IHC Holland. Billiton Marine used the dredge for tin production at Pulau Tujuh in Indonesia (Dieperink, 1978) before it was laid up in mid-1985. Bima underwent a nine-week refit before departing Singapore on June 4,1986, with 800-t (880-st ) of deck cargo. It was dry-towed for 32 days to Alaska. A slower, less expensive, wet-tow at the authorized 5.5 kmthr (3 knots/hour) would have delayed the dredge's arrival in Alaska untl almost the onset of winter. The 13,000-km (8,100-mile) voyage was made on the deck of Smit Lloyd's "Giant-4" submersible barge towed by its 7.8- MW (10,500-hp) tugboat. The first season's dredging revealed several major shortcomings in Bima. Further repairs and modifications were undertaken at Tacoma, WA. The dredge returned to Nome for the June start of the 1987 summer dredging season. The refitted Bima worked offshore at Nome from 1987 to 1990. It produced 3.67 t (118,078 oz) of gold at an average recovered grade of 824 mg/m3 (0.0204 oz/cu yd). In 1991, the dredge was dismantled and sold.

Jan 1, 1997

By L. A. Bellows

The "Athabasca oil sands" of the McMurray formation in northeastern Alberta cover an area of about 21,000 square miles and contain the world's largest reserve of oil. Fort McMurray, a small town in the heart of the oil sands area, is about 235 air miles north- east of Edmonton. A railway serves the town but no year-round roads connect the town with the rest of Alberta. (Figure 1). The McMurray formation is of early Cretaceous age, deposited unconformably on a limestone surface of Devonian age. The sediments appear to have originated from the Canadian Shield to the east and were deposited in bays and deltas of large fresh water lakes. The lakes were later replaced by marine seas in which t the overlying Clearwater shale was deposited. (Figure 2).

Jan 1, 1963

By J. J. Zaluski

The Surface Mining control and Reclamation Act (public Law 95-87) (here-inafter the "Act" or "SMCRA") passed by congress in August of 1977 represents a comprehensive federal scheme for controlling surface coal mining and the surface effects of underground mining through permitting requirements, performance guidelines, and reclamation planning. While the provisions of the Act have been the subject of numerous legal challenges and court battles over the years, it is difficult to identify a more controversial program within the Act than the provisions for designating lands as unsuitable for surface coal mining operations. The lands unsuitable designation process provides for the acceptance and review of petitions submitted by citizens or organizations seeking to have specified land areas designated unsuitable for all or certain types of surface coal mining activities. In filing these petitions, the interested parties or petitioners are required to make allegations about potential adverse impacts on people or the environment and submit evidence supporting their allegations.

Jan 1, 1992

At the 25th Peruvian Mining Convention, the start-up of Antamina was called ?the mining event of the year.? Antamina, one of the largestcopper-zinc mines in the world, began operations in May 2001.Augusto Baertl is Executive Chairman of Compañía Minera Antamina, the operating company. He said in a convention address that Antamina would be in full production in 2002. ?I would like to stress that Antamina is, in every respect, a highly stringent operation, as it intends to be the Peruvianmine of the future,? Baertl said. ?Antamina has set the target of being, and remaining throughout time, a model mine as to technology, environmental practices and social responsibility.? [ ] In the areas of technology and operations, Baertl noted that ?we have incorporated the best engineering design available and state-of-the art technology for mining, grinding and transportation processes, among others.? In the environmental area, he said that ?we have carried out careful environ-mental impact studies and have incorporated modern technologies and methods to control and minimize any environmental impact.? In the social field, Baertl noted that ?our relationship with neighboring communities is being developed under the premises of the social responsibility philosophy.? These include popular consultation processes, environmental committees and conciliation discussion committees. The purpose, he said, is to encourage communities located within the area of influence of the project to find and lead by themselves their path toward sustainable development, beyond the life of the operation itself.?

Jan 1, 2001

By J. T. Kline

This paper will present a review of the underground leaching of remnant copper mineralization left as a result of the block cave mining operation at the Lakeshore Mine in Casa Grande, Arizona.

Jan 1, 1985

By William F. Riggs

In the fresh application of a frother, collector, or the change of any particular reagent, the interaction caused by this change is often overlooked since we attempt to solve a problem or improve a situation with use of a particular reagent without regard for the Interactions or side effects. When a particular reagent is added to a flotation circuit or substituted for another reagent, a series of chemical reactions occurs which. In turn, will create different physical responses. This discussion will provide a series of examples which have actually been experienced by the author.

Jan 1, 1994