Search Documents

By Anthony D. Hammond, Charles A. Kliche

A slope stability study for the Annie Creek and Foley Ridge Mines was undertaken to provide Wharf Resources, Inc. with a technical assessment of the stability of the slope for an overall pit slope angle of 60°. A rock analysis of the most critical and persistent combination of discontinuities was carried out using probabilistic methods. A detailed discontinuity mapping and assessment of the rock mass provided the orientation data used in this study. The orientation data were reduced and analyzed to identify the discontinuity sets. A statistical analysis provided information about the distribution of the data. A deterministic wedge stability analysis identified the critical combination of discontinuities; those with a low factor of safety were further studied using probabilistic kinematic and kinetic stability analyses. The results from this approach were used to obtain the reliability or probability of failure of the slopes.

Jan 1, 1988

By Virgil R. Huff, Ihor Havryluk

P. T. Pacific Nikkel Indonesia (PTPNI) was incorporated in Jakarta, Indonesia in February, 1969 by a group of Dutch and North American companies. At the same time, a Contract of Work with the Government of the Republic of Indonesia was signed, granting Pacific Nikkel all the necessary licenses and permits to explore and develop all nonradioactive minerals in two separate areas in Irian Jaya, eastern Indonesia. Nickel mineralization occurrences were confirmed by Dutch geologists in the two areas in 1952 and 1955, however, detailed exploration began in June 1969 after the Contract of Work was signed. Since that time, numerous studies and investigations have been conducted to determine the feasibility of producing metallic nickel in Irian Jaya. Four engineering studies, two bulk sample tests, an oceanographic survey, and a preliminary site investigation indicated that construction and operation of a nominal 100 million pounds per year metallic nickel plant on Gag Island were technically feasible. The fourfold increase in the price of oil in late 1973 without a corresponding adjustment in the price of nickel necessitated a reevaluation of the project, the results of which showed that the project required other conditions to be viable. Subsequently, analysis of: the future projected nickel supply-demand and cost-price relationships, the economics of treating a higher grade feed, and participation by the Government of Indonesia, indicate that the project will be viable. Therefore, planning of the Gag Island Nickel Laterite Project is continuing with the objective of commencing production to supply the market in the 1983-1984 time period.

Jan 1, 1979

By Kal V. S. Sastry

Modeling and simulation are two major tools available to a mineral process engineer for a consistent and systematic process analysis. The application of these tools to the analysis of specific mineral processing unit operations is well documented in the literature; nevertheless, they are used only to a limited extent in the industry. This is because the fundamental principles of modeling and simulation in the context of mineral processing context are not available. This paper represents the first in a series of papers planned to meet this need. General principles of process modeling and a unified mineral process model development methodology are presented. A simple example of model development using the flotation unit operation is given. A discussion of the practical significance, challenges and opportunities associated with mineral process modeling is included.

Jan 1, 1990

By Ewan Wingate, Ranjit Prasad, Yanjun Liu

The phosphorus journey begins with the extraction of primary phosphorus in the form of phosphate in apatite through openpit mining and, in some rare cases, underground mining methods. The ores are processed in beneficiation plants to remove impurities before the phosphate rock concentrate is either sold on the open market or converted into phosphoric acid in downstream chemical production facilities by the wet acid process or thermal phosphorus routes. These can in turn be converted into fertilizers, as well as used in the food and electronic industries. The advent of the EV battery has given rise to a new use for purified phosphoric acid in the production of lithium ferro phosphorus (LFP) cathode material for EV battery cathode assemblies. The production of LFP relies on raw materials such as lithium carbonate, lithium hydroxides, iron salts and purified phosphoric acid.

Feb 1, 2024

By D. L. Madge

The text of this chapter was not received in time for printing.

Jan 1, 1979

By S. Frimpong, E. Siami-Irdemoosa, S. R. Dindarloo

"Electric and hydraulic shovels are the dominant loading machinery in surface mining operations. Despite their critical role in production and their high capital and operating costs, no reliable and comprehensive quantitative performance metric is available. In this paper, a stochastic shovel effectiveness (SSE) measure is proposed for the purpose of quantifying the performance effectiveness of these shovels. The SSE is based on the widely used method of overall equipment effectiveness (OEE) in the manufacturing industry. The OEE measures the performance effectiveness of equipment by multiplying its mechanical availability, utilization and production quality. In manufacturing processes, quality rate is the ratio of the total number of products minus the number of defective products – equivalent to the number of acceptable products – to the total number of products. The SSE similarly uses the mechanical-availability and utilization terms, but instead of quality rate it uses a new parameter named bucket rate.The variability or randomness of the input data, that is, availability, utilization and bucket rate, are further incorporated into the SSE, and a final stochastic SSE distribution is derived in the form of a probability density function. One hydraulic and one electric shovel in a surface mining operation were selected to test the validity of the proposed method. The SSE scores for the two shovels, operating continuously for one year, were derived and compared. As with the OEE, the three-parameter SSE method yielded more representative results for overall performance measurement than a single-parameter approach. Using Monte Carlo simulation, a three-parameter Weibull and a normal distribution were derived for quantifying the overall effectiveness of hydraulic and electric shovels, respectively. As a decision aid, the proposed methodology promises to render a more informative tool than traditional metrics for mine equipment maintenance and management."

Jan 1, 2015

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012

By Arafat Ghosheh, Yousuf Abu-Rish, Darwish Amara, Mohammed Baderkhan

The Jordan Phosphate Mines Company is one of the world's major phosphate rock and phosphatic fertilizers producers (the second largest phosphate rock exporter), with ore reserves exceeding 2 billion tonnes, mainly located in the Eshidiya area. The Eshidiya phosphate deposits, 120 km north-east of Aqaba, are of sedimentary origin (as are all phosphate ore in Jordan). Three exploitable beds (Al, A2, and A3) with variable content of P205, CaO, SiO2, etc., are processed in order to produce 68-70,73-75, and 75-77% TCP grades. The A3 bed, which is characterized as the most siliceous containing 40-48% TCP, requires physical beneficiation using wet scrubbing, screening, and desliming by hydrocylone, followed by anionic conventional flotation to achieve 75- 77% TCP grade. For the last 15 years extensive laboratory and pilot tests (including physical, chemical, and mineralogical studies) were carried out. After operating the industrial plant, certain modifications were deemed necessary to adjust the operational parameters and the final flowsheet, which was followed to obtain the targeted quantity and quality of concentrate.

Jan 1, 1999

By Kevin Erwina, Rajiv Chandramohana, Connor Meinkea

This paper explores prevalent operational challenges encountered globally in SAG mills, including suboptimal throughput, liner wear, excessive energy consumption, and SAG mill load stability. The paper delves into the root causes behind these issues, such as ore variability, poor operating strategy, or inadequate process control. Drawing on industry experience and case studies, the paper highlights the significance of addressing these challenges to enhance overall mill performance and efficiency. It underscores the necessity of tailored strategies, encompassing improved monitoring, optimized liner designs, and refined control techniques to mitigate these challenges and promote sustainable SAG mill operation.

Feb 1, 2024

By Joseph T. Matoney, Okley B. Bucklen, Claude A. Goode, Philip G. Meikle

INRTODUCTION Annual coal production rose to over 1.03 billion st (931 Mt) in 1990. At the same time the number of mines producing this increased tonnage has decreased over 60% in a 30-year period, from 9230 mines in 1960.1 The great increase in production made possible through continued mechanization requires greatly improved loading facilities just to get coal away from the mine. Also the trend to combine production from more than one mine and cleaning it in a single preparation plant continues. A recent census of US coal preparation plants indicated that 310 plants were in operation.2 In addition to increased loading capacity, storage and blending facilities are more necessary both at the producer and user end. In this climate of rapidly changing technology, any written account is faced with the possibility of obsolescence before its appearance. Thus, this chapter seeks to define the common and current practice in coal loading and storage facilities with the full knowledge that this practice is an ever-moving target. FUNDAMENTALS OF COAL STORAGE Storage of coal is becoming an increasingly important part of coal handling systems at mines, particularly since the advent of the unit-train concept in transportation. In order to take advantage of reduced transportation rates on trainload shipments of coal offered by unit-train movement, operators have found that storage is an economic necessity. In unit-train practice, large predetermined quantities must be loaded in relatively short periods of time, as opposed to conventional practice where coal is loaded at a speed dependent on the production capacity of the mine and/or the cleaning capacity of the preparation plant. Clean coal storage is generally practiced in order to accomplish one, or a combination, of the following objectives: 1. To load out promptly and economically. 2. To facilitate blending in order to even out chemical and physical inconsistencies and to prepare desired products or to attain maximum product uniformity. 3. To store certain sizes whose prices and market demand fluctuate with seasons and to permit shipping in good weather. Coal storage, then, is necessary and desirable, both from production and utilization standpoints. There are, however, several undesirable aspects attendant to the storage of coal, the most important of which are oxidation and spontaneous combustion, changes in properties which may affect utilization of the coal, degradation of coal due to rehandling, and the added cost of handling and storage facilities.

Jan 1, 1991

By Richard D. Harvey

Petrographic properties of carbonate rocks are useful guides to the utilization of these rocks in SO2-scrubbing systems. High porosity and fineness of grain are thought to be the principal properties that contribute to high dissolution rates of the rocks in the scrubbing liquor. Lake marls and chalks are the major types of carbonate rocks that have these properties. Lake marls are composed mainly of equant grains of calcite (mean grain size generally less than 4 microns) weakly agglomerated in- to larger, porous particles. The marls commonly consist of 80 to 90 percent CaCo3 as calcite and aragonite. Impurities are, for the most part, quartz silt and organic matter. The average pore volume for samples of lake marls (1- to 1.2-mm particles) is about 0.50 cc/g, which corresponds to a porosity of about 57 percent. The mean size of pores in these marls is generally between 1 and 2 microns in diameter. Surface areas of lake marls range from 0.8 to 6.8 m2/g. Chalks have grain sizes and shapes similar to those of lake marls, but they generally have smaller amounts of quartz and organic matter and minor amounts of clay minerals. Pore volumes differ from one chalk formation to another; the 1- to 1. 2-mm particles average about 0.20 cc/g, which corresponds to a porosity of about 35 percent. The mean diameter of pores in chalks tested ranges from 0. 15 to 0.76 micron. Surface areas of chalks range from 3. 2 to 20. 1 m2/g. In the United States lake marls are restricted largely to Pleistocene- age sediments that occur in the states around the Great Lakes. Chalk and chalky limestones are restricted mainly to the Upper Cretaceous and Tertiary strata in the Kansas-Nebraska-Colorado area and in the south- eastern states, from Texas to Florida. Results of laboratory tests of the relative dissolution rates of samples at pH 6 and 44°C indicate that, in addition to many lake marls and chalks, oolitic aragonite, pelecypod shells, and carbonate waste sludges from certain industrial plants also have high dissolution rates.

Jan 1, 1974

By Patrick Oriez, Chris Norris, Alain Mercusot

"Temporary mechanical ventilation is one of the fundamental requirements in guaranteeing a healthy atmosphere in underground construction works in order to protect the health of persons working on the site. It is therefore essential to conceive a system which meets the requirements of the whole of the worksite and for all phases of work which takes into account all aspects pertaining to its design, dimensioning, justification, installation, maintenance and validation. In doing so, the ventilation design and the selected apparatus to be installed shall meet with the degree of health protection and the quality of air of the worksite as defined by the legislation in force in France, through limiting the concentration of the different pollutants associated with the site activities. Consequently, when presenting a mechanical ventilation project, all of the participating parties and especially the contractor make a commitment to guarantee sufficient volumes (or airflow rates) of fresh (non-polluted and oxygenated) air and extracted (polluted) air in order to meet these limitations and maintain them in all conceivable site configurations. This article sets out the most important aspects of the implementation of a ventilation project from the initial design stage through to its application, discussing French legislation, ventilation principles, calculations and techniques with regards to underground construction sites. BASICS OF VENTILATION Mechanical ventilation studies are concerned with all of the site workstations and work phases which are sources of pollution and apply to all zones of the underground worksite with the goal of maintaining the concentration or composition of this pollution below the permitted levels and comply with the following three basic principles which are complementary to one another without being in contradiction. •,The first principle consists in eliminating or limiting as much as possible the emission of any polluting, irritant, or dangerous substances, by specifying appropriate construction techniques and equipment (use of electric motors, combustion engine equipment: filters, tanks, catalyzers, use of less polluting explosives, damping down dust with water or wetting products, damping down and diluting certain gases using water mists). •,The second principle is designed to capture residual polluting substances emitted close to the source in order to prevent them from spreading into the worksite atmosphere (extraction ventilation with ducting up to the source – upstream of the extractor fan – and use of downstream filters before expelling the polluted air to the exterior). •,The third principle involves accompanying the capture of the pollutants with additional blowing ventilation specific treatment of substances dissipated by and distant from the source of pollution (acceleration of the drift air flow in order to confine dust and better capture it, supply ventilation with ducting in order to dilute the gases emitted and discharge them to the exterior)."

Jan 1, 2016

By Gh. Crutu

During exploration and exploitation of complex ores, waste dumps that contaminate severely the environment and in particular soils and waters, are genetated. The most hazardous pollutants are heavy metals and metalloids (e.g As, Mo, Pb and Cu) as well as radionuclides (e.g U and Ra).

Jan 1, 2008

By Frank W. Bowdish

During the early 1960's, a method was developed for refining sand from the Arkansas River to produce a feldspathic product that was proposed for use in making colorless glass. Because of the need for chemical uniformity, a cooperating glass manufacturer specified certain ranges of percentages for each chemical constituent of the sand. These specifications were met by fulfilling the single requirement that alumina vary by no more than 20.1 percent from the specified value. This translated to a total variation of only about 1 percent in the feldspar content of the mixed quartz-feldspar products. Because the feldspar was lighter than the quartz, the average density of refined sand varied depending on composition. Densities, determined to five significant figures, of several samples were correlated with their chemical analyses, and the correlation could then be used with density determinations to more reliably indicate compositions than by chemical analyses only. The effects of several variables on the composition of refined sands were studied. There was a regular variation in the proportion of feldspar with screen size. A series of samples with their natural size distributions were more nearly uniform in composition than the same sands after screening and recombination. The screening and recombination process was done so that the sands had identical size distributions. Variations in the refining showed little effect on composition. A pile of flow-back sand from a construction sand washer was found to be severely segregated. However, samples taken from many points in the river near the sand plant and from the flow-back discharge pipe over several weeks very nearly met the uniformity specification. If care was taken to avoid segregation either before or during processing, it should be possible to meet the uniformity specifications for a feldspathic glass sand.

Jan 1, 1978

By Steve Trussell, William H. Langer

"Arizona aggregate (sand, gravel and crushed stone) producers enjoyed more than a half a century of nearly constant growth in demand for aggregates. Approximately 80 percent of the aggregate produced in Arizona is sand and gravel, and 20 percent is crushed stone (U.S. Geological Survey, 2015). Figure 1 shows the generalized distribution of potential sources of sand and gravel (yellow) and potential sources of crushed stone (other colors described below). Black dots show locations of aggregate operations.Sand and gravel commonly is produced from modern river channels and terraces although some alluvial fans and high-level paleo-river terraces also serve as aggregate resources. The gravel clasts are a mix of rock types that reflect the types of rock in the source area of the rivers. Generally processed river gravels meet stringent specifications for highend uses.Crushed stone, which makes up about 20 percent of production, primarily comes from a variety of metamorphic rocks and light-colored intrusive igneous rocks such as granite (brown areas), dark colored extrusive igneous rocks such as basalt and scoria (rust colored areas), and carbonate rocks such as limestone or dolostone (green areas). Carbonate rocks are also used in the manufacture of cement and lime.Construction and aggregate production in ArizonaBecause aggregate producers have limited facilities for storing product, stockpile changes are insignificant compared to production. Therefore, demand or consumption of aggregate in Arizona is considered to be equal to production. Production figures used in this paper reflect shipments, sales or marketable production, including aggregate used by producers to make readymix concrete and asphalt. Production figures were reported by the U.S. Bureau of Mines from 1950 until 1995 and by the U.S. Geological Survey (USGS) since then. Production figures are reported voluntarily, and major operators are the primary source for these figures. Because many smaller operators do not report their production, the figures are conservative values that provide an approximation of aggregates production activity."

Jan 1, 2015

By J. L. Thompson

The combustion of pulverized coal is a century-old practice. Many people have investigated coal dust and the residual fly ash particles that re-main after combustion. But the combustion process and fly ash formation mechanism are not under-stood. Working at our Maysville, Kentucky lime plant, the Dravo Lime Company Research team has collected samples of partially burned coal dust from the flame of a pulverized coal burner. Specimens were placed in a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). Microscopic examination of the particles, together with a large collection of micrographs of lime dust fused to fly ash particles, now make it possible to theorize as to how combustion advances through a piece of coal dust. Coal is a physical mixture of carbon-based compounds interspersed with bits of ash-forming materials, primarily alumina-silicate compounds. The alumina-silicate materials are commonly in angular nodules measuring 100 A to 700 A across their major dimension. It would appear that if the coal particle is in a well mixed gas stream, combustion starts at the surface and advances radially toward the particle center. With poor gas mixing, it is common that combustion moves from one end of a particle and advances on a broad front almost normal to some axis. In either case the combustion process and ash-forming mechanism are the same. As combustion occurs the carbon-based compounds oxidize in a highly exothermic reaction. Heat from the re-action melts the alumina-silicate nodules causing them to flow together and coalesce into an open sponge-like structure. As melting continues surface tension of the liquid and free surface energy causes the sponge-like structure to simplify into fewer, larger pores. Most likely the lighter molecular weight hydro-carbons burn before the heavier species. This means that as the melting ash structure is metamorphosing to a single large pore, there continues to be out-gasing throughout the structure due to combustion. Surface tension will form a spherical piece of fly ash if the ash material is liquid for a sufficient period of time. Out-gasing from combustion of the heavier hydro-carbons will provide internal gas pressure to keep the particle spherical until it freezes.

Jan 1, 1978

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Heather Dougherty, Ted Klemetti, DYKE MARK VAN, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

By T. Qiu

"The purpose of this study is to investigate the effect of the dosage of sodium hypochlorite as activator on the flotations of depressed marmatite and depressed chalcopyrite, with a focus on activation-flotation kinetics. Four flotation kinetic models were applied to test data using 1stOpt statistical analysis software to estimate the relationships between the maximum flotation recovery rates for the depressed marmatite and depressed chalcopyrite, the flotation rate constants and the sodium hypochlorite dosages. Within the range investigated, the highest flotation performances of depressed marmatite and depressed chalcopyrite were obtained at 2.5 mL/L sodium hypochlorite with zinc recovery rate of 93.8 percent and 3 mL/L sodium hypochlorite with copper recovery rate of 94.6 percent, respectively, after four minutes of flotation. A second-order model with rectangular distribution of flotabilities gave the best fit to test data collected at various sodium hypochlorite dosages. For the highest flotation performances of depressed marmatite and depressed chalcopyrite, the respective equations of their flotation models were derived and presented.IntroductionCyanidation tailings are the solid residues generated by gold plants that use cyanide to extract gold (Lv, Ding and Qian, 2015; Zhang, Li and Yu, 2013). Because of increasing demand for gold, the Chinese gold industry has developed rapidly, with production amounting to 451.799 tons in 2014, an increase of 5.5 percent from 2013. Chinese gold production has been the highest in the world for eight consecutive years. As a result, more than 2.45 million tons of cyanidation tailings are estimated to be discharged into tailings ponds every year (Li et al., 2010; Lv, Ding and Qian et al., 2015; Wang et al., 2015; Zhang, Li and Yu, 2013; Zhang, Li and Yu, 2012), and approximately 300 million tons of cyanide tailings are stockpiled in China, with the potential to cause serious environmental pollution as well as death to wildlife (Adams and Lloyd, 2008; Donato et al., 2007; Hewitt, Breuer and Jeffery, 2012; Velasquez-Lopez et al., 2011; Stephen et al., 2009; Zagury, Oudjehani and Deschenes, 2004). Concerns over cyanidation tailings are not exclusively environmental but also economic, as tailings occupy considerable land area, and tailings storage facilities increase the production costs of gold enterprises (Donato et al., 2007). Tailings often contain other valuable metals such as zinc, lead and copper. For example, the cyanidation tailings of Gaoyao Hetai Gold Plant in Guangdong Province contain 2.5 percent copper (Cu), 0.31 percent lead (Pb), 0.23 percent zinc (Zn) and 15.36 percent iron (Fe) (Shi, 2008), and the tailings of Tianshui Gold Plant in Gansu Province contain 1.94 percent Cu, 5.96 percent Pb, 0.27 percent Zn and 24.62 percent Fe. Cyanidation tailings have therefore been increasingly viewed as a secondary resource rather than waste."

Jan 1, 2016

By Dr. David R. Hargis

Finite-difference digital computer models can be used to evaluate the effects of proposed mine dewatering and depressuring operations on ground-water aquifer systems. The effects of proposed dewatering and depressuring operations can be simulated for both underground and open-pit mining in confined and unconfined aquifer systems. Design of dewatering and depressuring well arrays to accommodate proposed mining operations in a variety of hydrogeologic settings can be accomplished through judicious application of well-documented and tested computer programs that are widely available from government agencies and universities. The speed and flexibility of the computer models can provide an economical means for comparison of alternative mining plans, and can be used to determine the optimum mine plan with respect to dewatering requirements.

Jan 1, 1980

By S. K. Palm

Volatility is a fact of life in the mining industry. Prices of and demand for mineral products are among the most volatile of those for any product. The volatility of these markets wreaks havoc on both corporate management and the personal lives of mining people. Yet, until recently, it has been difficult to assess the impact of volatility on business strategy. This paper discusses how mining firms can profit from market volatility through an operations strategy that stresses operating flexibility. The foundation for our strategy analysis is the observation that a mine is analogous to a stock option. Techniques based on those developed to value stock options have recently been extended to the field of mine valuation. The insights provided by option pricing are very valuable in the development of mine operating strategy.

Jan 1, 1986