Search Documents

By G. D. Elliot, R. L. Grayson, G. L. Winn

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate was approximately 10 times higher than the national coal-industry fatality rate. Although the number of fatalities went down from 22 in 1991 to 17 in 1992, West Virginia still led the nation in coal-mining fatalities. A team of mining and safety professionals from West Virginia, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training, studied this problem. A clear path for formal intervention was determined and is presented here.

Jan 1, 1996

By B. D. Shah, H. S. Soto

Lack of selectivity in mixed mineral flocculation can be attributed to one or more of the following factors: dissolved ion interference, hetero- coagulation, mechanical entrapment in flocs, and entrainment of fines between flocs. In a study of the apatite-dolomite system, it was determined that dissolved ions do not have a significant effect on selectivity. Heterocoagulation was minimized by choosing proper process conditions and addition of a dispersant. Mechanical entrapment was proved to be insignificant and efforts were made to reduce entrainment by choosing an appropriate method of separation of flocs from fines. A new factor termed "polymer induced entrapment," which occurs due to limited affinity of the polymer to the mineral that is not flocculated, is postulated to be the cause for the loss of selectivity.

Jan 1, 1988

By Bill Dershowitz

Consider a deep gold orebody with grade of 4 g/t (0.11 oz/st). At the time of this writing, with gold prices at historic highs, it could be a good, but not great, prospect. But if it is a vein deposit, and those veins are 200 g/t (5.8 oz/st), it would be significantly more attractive if there was a way to produce directly from those veins, leaving the rest of the rock in place. [Figure 1 The red around each of the four injector wells shows areas of high pressure, where the lixiviant fluid is pumped into the rock mass, with orange and yellow indicating dissipated pressure. The black lines indicate some of the fracture pathways through which the lixiviant, with absorbed metal, flows toward the central recovery well where low pressure is indicated in blue. Lixiviant is pumped out through the recovery well. Image courtesy of Golder Associates.] There is a way to do this, in situ leach (ISL) or solution mining. It has been a viable commercial technology for more than five decades.

Jan 1, 2011

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which enables completely new designs of conventional shell and tube configurations. This article explains the principle and application of this self-cleaning heat exchange technology and also pays attention to an actual case of a revamp of the severely fouling exchangers of a conventional multi-effect evaporator into a self-cleaning configuration. Possibilities for the revamp of conventional exchangers suffering from massive and very hard scale deposits are found in a variety of metallurgical processes, such as: The refining of nickel, the production of alumina from bauxite and many others.

Jan 1, 2003

By J. E. Carr

A bewildering number of continuous thickeners and clarifiers are used in mineral industries and other heavy industries. General types are: 1. Conventional Thickeners (Fig. 1). 2. Thickeners with Flocculating Feedwells (Fig. 2). 3. Solids Contactors (Fig. 2). 4. Tray Thickeners (Fig. 3). 5. Lamellas (Fig. 4). 6. Conventional Thickeners with Lamellas 7. High Flow, Fluid Bed Thickeners (Fig. 5). These units must be adapted to varied applications. They must provide operating flexibility to meet process needs. Such factors multiply the decisions which must be made prior to the selection of a thickener. The seven types of thickeners listed above, with their variations, share design concepts which limit their application and which can be used to evaluate their performance. Some of these are listed: 1. Feed velocities must be limited and/or controlled. 2. Natural or reagent flocculation is necessary. 3. Horizontal settling area is the basis for capacity. 4. Overflow velocities must be limited and/or controlled. 5. A controlled underflow is necessary. Applying these needs to the basic process concepts is thickener selection. The basic function of a thickener in the minerals industry is the separation of a thickened sludge containing fine solids from water. To this primary separation function are frequently added others to give a list as follows:

Jan 1, 1977

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

The purpose of this work is to develop a conceptual recovery process for thorium dioxide (ThO2) from its primary source, monazite. The study-level design presented in this paper represents an economically viable method for conducting ThO2 extraction from monazite ore while also recovering byproducts that include P2O5 and other rare earth element oxides rather than producing unnecessary waste streams. Three key points to note in the development of this process design are: (1) the process economics relied heavily on recovery of rare earth byproducts, (2) the thorium handling portions of the process could effectively be segregated from the rare earth and phosphate handling portions of the process, and (3) the thorium and uranium content in waste streams should be carefully managed and eliminated where possible.

By Mathew B. Revell, Martyn L. Bloss

The paste fill system at BHP Cannington's underground silver-lead-zinc mine is described. The paste fill system has been operational since December 1997 and is the first of its type in Australia. Technical and operational learnings since stope filling commenced are presented. Topics described include plant performance, reticulation system design and construction, pipe wear and failure, rheology, in situ performance and laboratory testing.

Jan 1, 2001

By Vathsala Rajagopal, lwao lwasaki

The grinding media materials for the mining industry require corrosion and abrasion resistance properties not only to minimize the wear but also to improve the flotation recoveries of sulfide minerals. The media wear mechanisms and the factors influencing the grinding ball wear during grinding are discussed with respect to abrasion, corrosion and impact wear of grinding media materials. Interactions between the grinding media and sulfide minerals in a ball mill adversely affect the floatabilities of the ground minerals. The possible galvanic interactions between grinding medium-mineral and their effects on the flotation responses of sulfides are also reviewed. The selection criteria for alloy composition that reduces the overall wear along with adverse effects on flotation are brought out.

Jan 1, 1992

By Andrew Neale

ERIC GUTIERREZ: With that, we'll go ahead with the final speaker of the day, Andrew Neale. Andrew has a master's of science degree in mineral processing from the University of Alberta. He worked at the Falconbridge in Sudbury area, also at Brenda Mines, and then he became part of the Brenda Process Technology group in British Columbia. He joined Freeport in late 1993 in Indonesia, and was involved in process control and automation. He is now the senior manager of metallurgy in New Orleans. He's responsible for designing Freeport's new 100,000-ton-per-day expansion concentrator, which is currently being commissioned. Please welcome Andrew. ANDREW NEALE: With the ongoing explosion in digital computing power, there seems to be no limit to what can be modeled, simulated, and controlled in the mineral processing plant. However, at each stage of development of a control system, it is necessary to complete a cost-benefit analysis for justifying the move to a higher level of control. Incremental improvements in plant performance, while often significant, must be weighed against the costs of implementation and long-term maintenance. This presentation will provide examples of what the author believes are misplaced or misguided process control efforts and make a case for the KISS principle as applied to process control.

Jan 1, 1998

By P. R. G. Bak

The integration of interactive computer graphics technology with data analysis tools can assist in the evaluation of deposit models: the super- imposition of mine openings on complex geology can be quickly perceived using dynamic visualisation, colour-coding and transparency control while analysis functions assist in quantifying displayed information. To illustrate the functionality of such integration a research prototype system is presented which allows the interactive visualisation and evaluation of deposit models comprising both structural boundaries and the distribution of continuous properties.

Jan 1, 1992

By Maria C. Jaime

Optimization of the rock cutting performance plays a major role in the tunneling operation. For a given set of tool and cutting environment, rock fragments may be chipped away in numerous manners and it is crucial to understand and be able to predict the dynamics at the cutter-rock interface. This paper presents rational and realistic 3D finite element modeling of rock cutting where typical computational issues ?such as contact formulation, appropriate rock material response, mesh distortion, and crack propagation? are overcome. Cutting forces and failure mechanisms in this finite element analysis are successfully validated by laboratory single-cutter scratching tests in sandstone.

Jan 1, 2010

By S. S. SHINDE, P. C. JIKAR, N. B. DHOKEY

Mill scale is an oxide waste product of steel mills, containing around 70 percent iron and other allied impurities. In the present context, a dynamic prototype counter-current reactor (CCR) was used for the experimentation and simulation of a particle bed using the discrete element method (DEM). Mill scale was pulverized to ASTM mesh range 140 (106 μm)/+ 270 (53 μm) and oxidized in a CCR to make a single oxide Fe2O3 phase by maintaining the required thermodynamic conditions, such as pure oxygen at 1,100 °C. This oxidized powder was then subjected to a reduction reaction in the CCR, with gas mixture (H2:N2) ratio of 1:4 at 875±5 °C for filling degree, fd , and reactor revolution, ω, ranging from 5.38 to 16.14 percent and 2 to 5 rpm, respectively. A creeping fluid flow condition (Re < 1) and natural heat convection (Gr/Re2 >> 1) were maintained during the solid–gas reaction, and the particle-bed behavior was quantified by Froude number for the optimum operating window. The simulation was validated with the experimental results of reactor reaction product by X-ray diffraction (XRD) and scanning electron microscope (SEM) images.

By G. Danko

Ventilation and refrigeration for mine climate modification, contributes significantly to the operating costs of a deep hot mine. Mine climate simulation programs can be used to minimize the impact of these costs. There are several computer codes available including CLIMSIM?, to assist in this work. Whichever simulation program is used, it is the mine ventilation engineer who must supply the input data. This paper raises and answers the following question, namely: what accuracy is required of the basic input parameters, in order for a certain precision to be obtained in the predicted air temperatures? In the first part of the paper a new approach is described to estimate the dry and wet bulb temperature of the airflow, either in a dry or wet roadway. The calculation procedure allows an arbitrary temperature change with time, using Duhamel&apos;s superposition solution. Matrix-vector representation is applied to simplify the computational structure. In the second part of the paper the sensitivities of the dry and wet bulb air temperatures are analyzed to the changes of the rock thermo-physical properties, the heat transfer coefficient and the wetness factor.

Jan 1, 1988

By A. B. Samaddar

A prototype automated mapping and spatial information management system has been developed, and illustrates how a powerful map manipulation capability and a comprehensive display system can be combined using both raster and vector mapping: The concept of a mapbase and information retrieval mechanism, query language as well as text and graphical menus, is introduced. The Geographic Information System (GIS), which has been built around a system for storage and retrieval of spatial and textual data, allows interaction with geographic space represented on a displayed map. The prototype is demonstrated using maps and information of an open pit mine.

Jan 1, 1989

By E. Woodburn, R. Putman, A. L. Mular

Optimization strategies of possible interest to mineral processing are reviewed and typical strategies initiated in processing plants to date are discussed. Both On-Line and Off- Line optimization procedures have been employed by industry, assisted either by operators or by digital computers. In every case, dollar benefits have accrued.

Jan 1, 1976

By Curtis A. Pledger, H. Lee Wimmer, I. Michael Gowring

The Upper Diamond Fork Project, as part of the Central Utah Project Completion Act, conveys water six miles from the existing Sixth Water Aqueduct to the Diamond Fork Pipeline. During design, a Value Engineering team proposed a single-tunnel alignment that would be less destructive on the environment and might have a lower life cycle cost than the proposed design of two tunnels connected by two pipelines on steep hillsides. A decision was made to include this option in the bid process as a design-build alternative. The bid for this option was the lowest and a contract was awarded. During the TBM excavation a segment of tunnel wall caved in containing large quantities of water saturated with extremely high levels of hydrogen sul?de (H2S)gas (measured at 380 to 520 ppm in the air). The Central Utah Water Conservancy District (District) in consultation with Obayashi/Clyde (Contractor) quickly developed anew plan to finish the system by incorporating parts of the original tunnel/pipeline concept and re-bid the remainder of the project as a Phase 2 Design-Build contract.

Jan 1, 2003

By Andrew T. MacKenzie, Paul A. Rantala

Predictive pastefill rheology (flow characteristic), models have long challenged pastefill practitioners. While the methodology and practicality of recipe formulation is attainable in most locals, the remaining challenge has been to devise a predictive mathematical or empirical model of paste flow characteristics. Flow phenomenon can now be assigned mathematical and physical basis. The authors herein disclose physical and mathematical methods that demonstrate how operators could proceed when designing reliable pastefill systems. Knowledge presented will allow users flexibility in adjusting flow-rates. Laboratory data shows stiff pastefill delivery design can be derived through mathematical relationships of particle size, material characteristics and pipe diameter.

Jan 1, 2001

By Ernst Langer

INTRODUCTION Morro do Niquel is located near the small town of Pratdáolis in the southwest part of the State of Minas Gerais, Brazil, about 300 km in a straight line north of São Paulo and 300 krn west of Belo Horizonte. The deposit is known since 1935. Systematic exploration started, however, only in 1957 and production with one furnace in 1962. Since 1969, after the installation of a second furnace, the mine produces about 2 500 tons of nickel, contained in ferronickel, per year. This production is now consumed totally by the Brazilian steel industry. The "Morro do Niquel" is a serpentinite stock of 900 by 400 m which rises 200 m high above the surrounding metamorphic rocks of Algokian age (see Figure 1). On top of the hill there is a leached barren zone of about 200 by 400 m, generally 20-30 m deep, which consists practically only of a boxwork of quartz colored brown by limonite. Surrounding this zone on the sides of the hill is weathered, decomposed serpentinite which contains about 213 of the economic nickel mineralization. Roughly 113 of the ore reserves lie below the leached overburden representing ore of a different type. The geological map and cross-section, Figure 2, give a clear picture of the occurrence.

Jan 1, 1979

By R. K. Davey

Before the introduction of computerized procedures, mineralization modeling (compilation of level maps), ultimate pit studies, ore reserve compilations, and long-range mine planning all were performed manually. In fact, much of the basis for today&apos;s computer programs was derived from manual procedures and actual experience of mining engineers and geologists.

Jan 1, 1979

By Frederick T. Graybeal

Silver Bell is located about 56 km (35 miles) northwest of Tucson, AZ. It is a classic porphyry copper deposit containing enriched disseminated chalcocite ore in altered porphyritic rocks with chalcopyrite in adjacent skarn zones. The discovery of Silver Bell was an evolutionary process that occurred over a 75-year period. Recorded mining activity began about 1865 on Boot Hill east of El Tiro pit (see Fig. 1) where outcrops of altered limestones were found to contain 425 to 482 g (15 to 17 oz) Ag mixed with copper oxides. By 1874, the Young America Copper Co. was mining shallow occurrences of 30% Cu along the north side of the present Oxide pit. The ore was shipped by wagon to Yuma, AZ, and then by boat to San Francisco for smelting. By 1881, the district supported several mining companies, two small smelters, and was being favorably compared to Bisbee in local newspapers. Most of the ore mined in the period 1865-1903 came from pods of massive sulfide or their oxidized products which were distributed in an unpredictable fashion through a large skarn zone in Paleozoic limestone east of El Tiro pit. Ore grades varied from 5 to 10% Cu.

Jan 1, 1991