Search Documents

By H. Akgun, J. J. K. Daemen

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. Presented in this paper are the results of push-out tests on two types of expansive cement grout plugs emplaced in rock salt. The average interface shear strengths range from 2 to 12 MPa. Peak shear stresses (assuming an elastic stress distribution along the interface) are up to eight times higher. Dissolution along the interface may be enhanced by clay inclusions in the salt and appears to reduce bond strengths. Application of the results to the design of plugs for larger openings (e.g., shafts, drifts, or boreholes) is discussed.

Jan 1, 1995

By R. K. Singhal, R. Kolada

A variety of equipment is wed to surface mine oil sands, including bucket wheel excavators/conveyors, draglines, hydraulic shovels, and off-highway trucks. This paper examines the existing mining schemes and equipment wed. Several proposals to improve mine productivity have been presented.

Jan 1, 1988

By K. Kim, H. Gao

A site-characterization strategy formulated for the probabilistic assessment of rock mass properties is presented. The strategy, which takes into account the variability of rock properties and the stochastic nature of the rock-failure process, entails determining probability distributions of rock properties by utilizing extreme value statistics and Monte Carlo simulation. Laboratory and, field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass can be estimated by using this proposed method. The results of the analysis can be incorporated into the design of underground structures. Then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1997

By B. Catalano, D. Ifrim

The Annacis Island Outfall Project includes two TBM bored tunnels with face pressures above 3.5 bar, with an internal diameter of 4.2 metres. This paper discusses the innovative approach to TBM tunnelling and TBM design at the Annacis Outfall Project. The TBM custom design includes a 3.6 m OD core machine manufactured by Herrenknecht and a 5.0 m add-on by the Contractor (Bessac), acting as an extension kit, with optimized gantry design to accommodate for short tunnel drives and quicker launches. This novel design approach produced safety improvement, cost and schedule savings while streamlining logistics of TBM retrieval.

Dec 1, 2022

By F. L. Wilke, J. Fabian, D. Oravec

The task of production planning in ore mining is primarily con¬cerned with the removal of ore blocks within planning periods spread over the life of the mining operation. The investigation of this problem in the past resulted in the introduction of computer based optimizing techniques for production scheduling and se¬quencing. Although these techniques succeed in computing an "optimal" mine output for one planning period, they usually fail in composing a practical and feasible mine plan over the periods in concern. This paper describes conventional production planning based on operations research and the capabilities of a knowledge-based approach. An example of a planning system for the Slovak under¬ground iron ore mine Nizna Slana will be presented. By combina¬tion of these two techniques this system should improve the qual¬ity of planning procedures.

Jan 1, 1996

By Saurabh Rastogi, Vikram Shishodia, B. Pitchumani

Comminution is a unit operation which consumes major part of energy in mineral processing industries such as fertilizer production. Ball mills are widely used for size reduction of a given ore to the liberation size that is required in further beneficiation processes. In grinding of materials much effort is concentrated on control of top size of the product and this results in production of fines, also creates secondary problems of pollution due to the difficulty in the collection of fine particles. The present work has been carried out to control product size distribution for rock phosphate grinding in an Industrial Ball Mill of 600 TPD. The plant data are taken for a given feed distribution and mill operating conditions. The information at various Ball Size distributions are collected. The comminution functions such as specific rate of breakage and breakage distribution functions are estimated by back calculation technique to solve the mass balance equation. A simulation program is written to study the product size distribution obtained for various ball size distribution.

Jan 1, 1993

By T. R. Raponi, D. Barnes

The Williams Mine mines and mills 6000 t/d (6600 stp’d) of gold ore using SAG/ball milling, leaching and CIP, electrowinning and refining. Electrowinning, high-pressure cathode washing, filtering, retorting and refining are based around the use of knitted stainless steel mesh cathodes. Their primary advantage over conventional steel wool cathodes is that electrowon gold can be washed off and the cathode can then be reused. Typically, the knitted cathodes have a useful life of up to 15 months. Gold production of up to15 t/month (50,000 oz/month) is easily processed with this system. Presented is a description of this operation, including a review of the equipment and performance data.

Jan 1, 1992

By S. K. Bhatt

This paper reviews major developments in continuous haulage technology for underground coal mines. Haulage systems in use and development are investigated through a comprehensive literature search and visits to mines and manufacturers. The systems include flexible conveyor train, mobile conveyor, multiple- unit continuous haulage, extensible and belt turning systems. Strengths and weaknesses of the systems are assessed in light of their operating under remote control and their application to the computer-assisted continuous mining machine being developed by the US Bureau of Mines. Through mining scenarios, candidate haulage systems are conceptualized to be consistent with the capabilities of the mining machine.

Jan 1, 1991

By A. Wright

Gold Fields Mining Corporation is presently evaluating gold mineralization beneath thick, wet alluvium at the Chimney Creek Project, Nevada. Contamination of reverse circulation samples has been visually apparent since drilling began in the area. Tests have shown that, while contamination can affect assays, reverse circulation holes appear to define mineralized zones almost as well as the diamond drill holes. To improve reverse circulation sample integrity several techniques were tried including a stiff-mud injection system but with limited success. Diamond core drilling continues to be used in conjunction with reverse circulation drilling to further delineate the mineralization.

Jan 1, 1991

By R. E. Brewer

Pilot scale flotation tests were conducted with a 1-ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pct of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated using the column. The tailings were first water leached at approximately 600 C, and the water-leached tailings, which contained approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH and sodium sulfide addition on gold flotation recovery and redox potentials were examined. maximum gold recovery, 36 pct, was achieved at pH 8.5 with a sodium sulfide addition of 0.18 lb/st.

Jan 1, 1989

By Jean-Luc Cornet

As modern conveyors are increasing in size and complexity, their control requirements are becoming more and more critical. In addition to the safety and equipment protection requirements, control systems are now called to implement intelligent drive controls derived from dynamic analysis modelling, as well as to provide fast and accurate diagnostics while keeping operator controls simple. These requirements led to the development of a new and innovative approach to control system development. This paper describes the control philosophy used by Conveyor Dynamics, Inc. (CDI) and some of the key features of our approach to the architecture of control systems.

Jan 1, 1993

By V. T. Vacariu, P. D. Georgescu, N. Tomus

To assess the potential for radioactive pollution unique to the environmental conditions of the Bacau phosphogypsum waste dump, surface samples were taken, drillings were performed on the entire waste dump's height, and the Ra226 distribution on the height and surface considered to contain a medium content of the radium of 0.57 Bq/gr was studied. Thus, the waste dump's radioactive potential was estimated at 30-40 Ci in equivalent Ra226. Also analyzed was the granulometric composition of the phosphogypsum and the distribution of Ra226 on granulometric orders, which indicated that the radium was concentrated in the very fine fractions. Parameters were set up for the classification by hydrocycloning to obtain a fine class (less than 41 microns) having a radium content of more than 0.9 Bq/gr and a coarse class having less than 0.37 Bq/gr. A chemical process was devised for removal of the radium from the phosphogypsum with the possibility for recovering the contained sulfur.

Jan 1, 1999

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of US coal companies are developing seams previously considered too deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas in coal beds increases with depth, and ventilation requirements are much more stringent for deep mines than for shallower mines. When the longwall mining method is wed at great depths, ventilation, ground control, and operational considerations all influence the design of longwall panels. This paper examines these influences, particularly ventilation and operational considerations, on the feasibility of two-, three-, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1988

By R. D. Grove, M. F. Elliott, R. L. Weigel

The control of Florida phosphate flotation plants is largely based on the visual observations of experienced operators, both in recognizing good and bad froth conditions and in making judgments about the composition of feed, concentrate and tailing streams. Chemical analyses lag the process by at least two hours and therefore only assist in recalibrating the operators' vision when major deviations occur. An image analysis system has been developed by IMC Agrico Company (IMCA) to improve upon the accuracy and precision of the composition estimation process. It still relies upon the operator taking a representative sample, but provides a measurement in about 15 minutes after that sample is obtained. This paper describes the system and its use and presents comparative results for various process streams.

Jan 1, 1993

By Wayne Wride, Amy Lamb, Debra Sonntag

In today's "information age", we have the ability to collect volumes of data about a company's performance. The challenge is to turn that data into information employees can understand and use to fine-tune equipment, modify work processes, and ultimately manage production. Software programs have increasingly given end users control over what data is used and how it is presented. Kennecott has implemented an information system capable of collecting and storing data at the primary level. This enables plant personnel to transform historical data into information for action. Kennecott plans to expand its data collection and use trending and reporting capabilities to move toward a fully optimized operation.

Jan 1, 2000

By G. T. Adel

The flotation behavior of a -28 mesh Pittsburgh No. 8 coal sample is investigated through the use of Scanning Electron Microscopy in conjunction with Image Analysis. Release analysis is used to generate the flotation products, which are then characterized to provide the particulate composition in terms of pyrite, mineral matter and carbonaceous material. The results of this investigation indicate that the material recovered in the first stage of release analysis tends to be well-liberated carbonaceous material. This is followed by an increase in the recovery of middlings and fines in the later stages of the process. Any free carbonaceous material remaining in the tailings from the release analysis test tends to be associated with the very fine sizes (-400 mesh). Pyrite recovery is attributed to the hydrophobicity provided by small inclusions of carbonaceous material, since the amount of truly liberated pyrite particles (i.e., 100% pyrite) present in the sample is found to be negligible.

Jan 1, 1994

By A. M. Johnson, M. A. Cornachione

The west central Upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur that can create emission problems when processed in a kiln. A low-cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated. In this study, optimal conditions for the bacterium Thiobacillus ferrooxidans were created to promote pyrite oxidation and, therefore, sulfur removal from the slate. Preliminary lab scale flask tests using crushed and sized slate (-40 + 100 mesh) and T. ferrooxidans bacteria in a sulfuric acid medium resulted in 70% oxidation of pyrite over a one-month period. Subsequent column leaching tests on coarser materials (-3/8+1/4 in.) operated for six months resulted in a maximum reduction of total sum of 75%. These data suggest that bio-heap leaching to remove sulfur from the slate for use as a kiln feed material is viable.

Jan 1, 1995

By S. Kelebek, G. W. Smith

Four samples of galena, each prepared differently, dry ground chalcopvrite and real gar have shown various quantities of liberated sulfur corresponding up to nine equivalent monolavers on their surfaces as determined by the solvent extraction/UV analysis of sulfur using ethanol. The pretreatment of a dry ground galena sample with acidified ammonium chloride or neutral, saturated sodium chloride solutions rendered the mineral readily floatable. The collectorless floatabilities of galena pretreated with the former solution and of drv ground chalcopvrite have been evaluated in reference to the natural floatability of sulfur using the critical surface tension of floatability approach with aqueous methanol solutions. It is shown that the amount of sulfur- on these samples can be correlated with their flotation rate, which was found to he first order within the critical surface tension range. The larger the concentration of surface sulfur, the faster the sulfide mineral floats, thus, the greater its flotation rate constant.

Jan 1, 1990

By P. D. Nora, M. G. Ranade

A statistically designed pot grate-kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables - bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate - were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a plant trial. The target firing temperature at the Empire plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets.

Jan 1, 1987

By M. Galetakis

The difficulties that rise during the evaluation of multiple-layer lignite deposits come from the deposit structure (alternating lignite layers with intercalated material of varying thickness), as well as from the limitations of the applied selective mining. Thin layers of lignite and interbedded waste layers are grouped under specified assumptions regarding thickness and ash content, to form the exploitable blocks. However, in practice the decision for excavating a block is made under subjective constraints of different importance or by using uncertain data. Advances in Fuzzy Inference Systems (FIS) have provided a new approach to the evaluation of multiple-layer lignite deposits. FIS have the ability to handle imprecise or incomplete or linguistically ambiguous information and to incorporate them into decision-making processes. In the developed FIS (Mamdani type) new linguistic variables, concerning with working conditions, operators? experience and production were involved. The FIS was used for the estimation of quality characteristics and reserves of the exploitable lignite produced from Southern Field mine, Ptolemais (Greece).

Jan 1, 2005