Search Documents

By B. K. Mishra, A. Datta

Estimating the power draw of a ball mill is of great importance from both operational and control standpoints. There are many factors that affect the power draw, and its prediction is particularly difficult in an operating plant. The important factors that affect power draw are the mill dimensions and operating parameters. Although mill dimensions remain the same for any given mill, the operational factors, such as ball load, mill filling and mill speed, may vary. This makes the modeling effort extremely cumbersome. It is for this reason that an artificial neural network is considered for the development of a black-box-type model to predict power draw. In this work, a total of 48 sets of plant data are used. Using these data, a neural network is built and trained. The trained network is used to predict power that is found to be in good agreement with operating mill power for many situations. In addition, the results of simulations are also com- pared to those obtained from a discrete-element method- based power-draw model.

Jan 1, 2000

By Earl Gardiner, Michael Grenier, Stephen Hardcastle, John Vergunst

A prototype, self-contained mine refuge station air supply sys- tem was tested in an underground metal mine to verify it's ability to keep oxygen and catbon dioxide levels at acceptable concentrations in an emergency situation. In this test, 25 volunteers were assembled and sealed in a functional underground refuge station for a period of 24 hours, without the benefit of the standard com- pressed air supply. The prototype system was designed to: 1) operate on a self-contained power supply for a period of at least 27 hours; 2) supply oxygen at a metered rate; and 3) remove car- bon dioxide by re-circulating refuge station air through soda lime scrubbing beds. During the test period, the catbon dioxide concentration remained at an average of 2500ppm and oxygen concentration stayed between 20.2% and 20.6%. The volunteers found the prototype easy to use and seemed confident in its ability to provide a safe atmosphere. The test showed that this technology could become part of an underground mine's refuge station emergency equipment.

Jan 1, 1997

By Peter Hornby, Maurice Craig, Franklin G. Horowitz, Don Bone

We have developed a high-performance, flexible scheme for interpolating multi-dimensional data. The technique can reproduce exactly the results obtained, for example, from Ordinary Kriging and related techniques in 3D, or from Thin-Plate Splines (Briggs' minimum-cuwature algorithm) in 2D. Moreover, com- pared to traditional implementations of these algorithms, our method enjoys large computational-cost savings. The new approach produces an interpolation that obeys a Partial Differential Equation (PDE). The PDE may arise from physically based arguments, but its form can vary widely. It might be specified only implicitly (as through a Model Variogram), or be nonlinear (although a performance penalty could then apply). While a formal equivalence between Kriging and Splines has been known for some time (Matheron, 1980), the present derivation, from radial basis functions, further illuminates this connection. Thus, for example, we can make explicit the PDEs that underlie some of the Model Variograms most often used in Geostatistics. Besides its practical utility, the work thereby ac- quires a theoretical interest.

Jan 1, 1996

By R. J. McLaughlin

Acid mine drainage (AMD) can occur as a natural phenomenon through oxidation of sulfide minerals. Oxidation by air and water can be exacerbated by mining. Because AMD can exhibit low pH, it is capable of extracting heavy metals from mineral deposits. The result is highly acidic drainage with elevated heavy metal concentrations -the combination of which can cause extensive environmental damage. Because of the importance of these factors, this paper is focused on sulfate based AMD. Due to widespread mining, the occurrence of AMD is ubiquitous. As a result, several approaches to treatment have been developed. Chemical treatment using alkali is most commonly employed to treat AMD. There are alternative methods of treatment, as well as alternative ways of handling treatment sludges or concentrates. Dewatering of sludge or concentrates is beyond the scope of this paper.

Jan 1, 1996

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016

By Bror Nyman

Wide settlers are a way to decrease the linear velocities of advancing liquid phases. It has, however, been found unnecessary to risk a proper settler performance by building shallow settlers in order to avoid a so-called interface turbulence due to a too big difference between the linear velocities of the organic and the aqueous phase. This conclusion has been reached from tests using a large transparent settler model, where the behaviour of a clean interface between two advancing liquids has been investigated. Also in a more realistic case, making an organic in aqueous or an aqueous in organic dispersion to move between the liquid phases, no obstacle has been found to use a somewhat more deep and correspondingly ore slowly t10wing aqueous phase. Based on above findings, support can be given to a new trend to build the settlers slightly deeper than what has been typical for the so-called low-profile design. In this way, it is much easier to avoid an excessive air introduction and other severe difficulties, like those caused by crud moving from one stage to another. It is further shown, how gravity can be used to slow down and distribute a dispersion being fed into a settler of a VSF unit. Entrainment levels have been found to be reduced by a careful design of primary dispersion distributors and picket fences of the settler. Finally, it is demonstrated, how outlets from the side of the settler can be used to simplity interstage pumping and to decrease the rotation speed of any pumping device.

Jan 1, 1996

By David Beck, Eko Wibowo, Hendri Silaen, Andres Sugiyanto, Karl Llewelyn

PT Freeport Indonesia’s Deep Mill Level Zone mine is one of the deepest block cave mines in the world and is in mountainous terrain in West Papua, Indonesia. The mineralization is hosted in a skarn deposit in a structural setting that is complex at the footprint, mine and regional scale. Large seismic events and significant episodes of rapid rock mass deformation are potentially critical geotechnical risks during this ramp-up stage of mining. Understanding the interaction between stress, strain, rock mass strength and geological structures is essential to minimize the hazard and engineer control measures to help ensure the safety of the employees while achieving production targets. This paper discusses how the seismicity and excavation damage have been shaped by the interactions between the mine and geological features, and how this affects strategic mining decisions. Additionally, the paper presents a summary of the mitigation measures used for mining the DMLZ in the safest and most productive way. These include improvements to geotechnical characterization of rock mass and structure, dynamic ground support designs, production scheduling for desirable cave propagation and a seismic monitoring system with re-entry protocols.

Apr 26, 2022

By T. J. Lutz, J. L. Carr, J. A. Yonkey, C. C. Jobes

"Since 1984, the date of the first recorded fatality involving a remote controlled continuous mining machine, 38 miners in the United States have been killed when they were struck by a continuous mining machine. Proximity detection is a valuable tool for preventing fatalities, and the use of these systems is expected to significantly improve safety. Proximity detection provides a means to prevent accidents like these. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a series of underground tests to evaluate the accuracy and repeatability of proximity detection systems under a number of conditions such as varying the orientation and height of the personal wearable device (PWD), moving the PWD close to the trailing cable, and activating the machine’s mining mode. At the 2014 SME Annual Meeting, results from tests on first-generation proximity detection systems were presented. This paper will provide results from the similar tests performed with second-generation systems. The results show that performance has improved. For example, the negative impact of PWD orientation and the trailing cable has been reduced. However, some inconsistencies remain. Notably, performance changes dramatically when mining mode is activated. INTRODUCTION Since 1984 there have been 38 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM) [1]. In August 2011, the Mine Safety and Health Administration (MSHA) published a proposed regulation that would require proximity detection systems on all continuous mining machines except full-face machines [2]. Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHA-approved proximity detection systems are commercially available. MSHA estimates that of the 38 fatal striking and pinning accidents that have occurred since 1984 involving CMMs, the use of proximity detection could have been a preventative factor in at least 28 cases [1]. Furthermore, MSHA estimates that proximity detection could prevent 20% of all deaths throughout the industry [3]. NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system [4] and have recently conducted research intended to develop more advanced proximity detection technology for CMMs [5,6,7,8]. In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate [9,10] and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators [11,12]."

Jan 1, 2015

By Mark A. Koestel

Cobalt-sulfide mineralization can he found in potentially economic quantities where permeable, basal Cambrian formations "pinchout" against Precambrian pal eotopographi c highs. These environments are common around the Saint Francois Mountains of southeastern Missouri and they share many similarities with the geologic environments of Zambia and Zaire in South Africa. Exploration for this type of deposit involves test drilling targets identified by trend analysis from past drilling, geophysics, geochemistry and a comprehensisve study of regional geology and isopach maps. Innovative ideas, new exploration concepts and insoluble residue geochemical methods may provide the necessary "edge" needed to complement basic geologic understanding leading to ore discovery.

Jan 1, 1987

By Gilbert A. Bonforte, Hugh P. Caspe, Tracy K. Lundin

The Narragansett Bay Commission (NBC) Combined Sewer Overflow Abatement Program is a major effort to address and mitigate discharges from combined sewer overflows in the Providence, Rhode Island area. The proposed system consists of three deep rock tunnel segments totaling 17.8 km (11.1 miles) in length that will provide 860,000 cu m (227 million gal) of storage at depths up to 99m (325 ft). This paper discusses 13.5 km (8.4 miles) of 6.64m (21.8 ft) finished diameter tunnel, four construction shafts, 19 dropshafts and one large diameter pump station shaft tapered from 1 5.2m (50 ft) at the surface to 27.4m (90 ft) at depth. All facilities are in preliminary design.

Jan 1, 1995

By J. A. Cremeens, D. D. Overton, J. C. Varnier

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County, Colorado, USA were investigated using three-dimensional discrete element modeling methods. Large scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back analysis was conducted using pre-failure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and it afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. INTRODUCTION The Pikeview Quarry is an aggregate quarry located approximately five miles northwest of Colorado Springs in El Paso County, Colorado, USA. The quarry has been operated by several owners since the early 1900s. The Pikeview Quarry has been a major source of construction aggregate for the Colorado Springs area for many years (MSHA 1986). In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy. A large scale slope failure occurred on December 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on September 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure. The objective of this publication is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry. Both mechanisms are given equal credence in this publication. Quarry excavation was a key factor in the slope instability for both failure mechanisms. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability. GEOLOGY Regional and local geology are both important factors in slope instability at the Pikeview Quarry. Geologic structure at the quarry is related to regional mountain building and basin development associated with the Laramide Orogeny and the Rocky Mountains. Lithologies at the Pikeview Quarry are also related to regional trends. Localized geologic features, primarily related to weathering and erosion, have also been major contributing factors to slope instability at the Pikeview Quarry."

Jan 1, 2017

By Emily Sing, Ashim Gajurel, Thomas Pennington, William Brown

The Pardee Chemical Feed Shaft Project involves construction of two new chemical feed shafts to improve raw water treatment capabilities at the East Bay Municipal Utility District’s (EBMUD) Pardee Reservoir in Valley Springs, California. The project includes construction of two 250-foot deep, 16-inch diameter stainless steel chemical feed shafts that penetrate an existing 8-foot diameter concrete lined conveyance tunnel. The design approach required the shafts be installed using top-down drilling methods and within a strict verticality tolerance (0.1%). Innovative precision drilling techniques ensured that the shafts penetrated the tunnel in their planned locations and the installed chemical feed lines would function as designed. Challenges included extremely limited access to the tunnel because of a requirement to maintain the tunnel in service during construction. This paper discusses the overall project’s design and construction approach, including unanticipated conditions that the project team faced and how these conditions were managed and overcome through collaboration between the contractor, designer, and owner.

Dec 1, 2022

By J. D. Miller, C. L. Lin

"The use of 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles ranging in size from 150 mm to 1 mm at a voxel resolution of about 150 µm is now possible. This is quite a significant advance in X-ray tomography technology and promises to be useful for plant-site coarse particle characterization—size, shape, composition, density, texture, grain exposure and mineral liberation—with a response time of minutes after receiving the sample. This paper discusses applications in the mineral industries, including the coal industry, aggregates industry, metal mining and the processing of industrial minerals.IntroductionPlant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants and mineral processing plants is needed to improve plant capacity, product quality and/or process efficiency. Not much online coarse particle characterization is being done at these plants. Only some limited information regarding particle size is obtained online from reflected light images using analyzers such as the OPSA, Split and WipFrag™ analyzers. Even the laboratory analysis of coarse particles has been difficult because of the large amount of sample required to ensure statistical significance of the results. During the past several decades, laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage (Miller and Lin, 2004, 2009).Three-dimensional X-ray tomographic analysis has its origins in the medical services industry, where it is used to provide internal images of the human body. It has since been developed for nonmedical applications as well (Banholzer et al., 1987). Figure 1 shows a schematic diagram of the cone-beam geometry micro-CT system. In our case, X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two-dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a threedimensional image is reconstructed from the collected set of projection images."

Jan 1, 2016

By R. Mensah-Biney

The kinetics of loading of gold from bromide solution onto an anion exchange resin, PAZ-4, were investigated in a batch stirred reactor. The initial loading rate was described mathematically by a first-order reaction rate equation. The effect of agitation speed, temperature, resin particle size, resin concentration, initial concentration of gold and bromine in solution on the rate was investigated. The model described fairly accurately the loading process in terms of the variables investigated. The rate constant for the initial loading ranged from 0.5 to 1.3 x10-3 sec-1 and the half-time was 9.3 to 56 minutes. The initial rate constant increased with increasing temperature with an activation energy of 15.7 kJ/mole (3.8 kcal/mole). The rate constant was directly proportional to the concentration of the resin in solution. The subsequent reduction reaction was also modeled by the first-order rate equation and the apparent rate constant was estimated to be 3.0 x 10-6 sec-1 with a half-time of about 44 hours.

Jan 1, 1994

By John F. Abel

Convergence measurement across the 17.4 m (57ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 by 9.6 m (38 by 31 1/2 ft) I.D. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2 3/4 in.) and 5.7 cm (2 1/4 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1984

By S. S. Xue

A study has been conducted to remove iron from sulfate solutions using Eichrom's Dipex® extractant, P,P?-di(2-ethylhexyl) methanediphosponic acid (H2DEH[MDP]). It is found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 10 6 Over 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 1999

By I. E. Odom

The rare magnesium-lithium clay mineral hectorite occurs at many places in the McDermitt caldera of Nevada-Oregon. Commercial development of several high purity deposits began in 1986. The hectorite was precipitated in a lake environment formed after collapse of the McDermitt caldera. Hectorite beds and lenses are associated with volcaniclastic sediments, limestones, dolomites, zeolites and locally sandy bentonites. The high purity deposits appear to be associated with hydrothermal areas. The hectorite consists of extremely small flake-shaped crystals, and Ca is the predominant exchangeable ion. Its color ranges from white to light green. Commercial uses developed to date include high brightness magnesium aluminum silicate products, organophilic clays, pulp retention, and ceramics. The MAS is used as a suspending agent, binder, stabilizer and thixotrope in aqueous solutions for cosmetics, household cleaners, pharmaceuticals and miscellaneous industrial applications. Organoclays are used in printing inks and paints.

Jan 1, 1992

By Langtry E. Lynd

The titanium dioxide pigment industry in the United States has always relied to varying degrees on imported titanium concentrates. Dependence on foreign ilmenite was especially high (generally over 85% of consumption) until 1942, when large-scale U.S. production of ilmenite began, and has since ranged from 12% to 47%. Rutile import reliance was generally in the 45% to 80% range until the early 1960's, when increased use in the chloride pigment process raised dependence on imported rutile to over 90% in most years since 1963. Import reliance of zircon, obtained almost entirely as a byproduct of titanium mineral production, has generally ranged from about 30% to 65% of consumption. This paper will examine the history of U.S. sources of these heavy mineral commodities, and will discuss the potential U.S. future supply in view of changing industrial uses and processes and the anticipated development of new heavy-mineral-sand processing operations, such as those at Richards Bay in the Republic of South Africa and in Sierra Leone.

Jan 1, 1978

By G. P. Hand

The purpose of this paper is to bring to your attention the various kinds of high performance graphites available today, their characteristics and possible applications. These materials are products of a proprietary high temperature technology developed by Superior Graphite Company. We feel we have only begun to tap the potential of this technology and the utilization of the resulting products. During the course of the paper, we shall investigate high purity, high performance graphites made from raw materials such as mined natural graphites, synthetic graphites and petroleum derivatives. We shall define their characteristics and resulting benefits to current applications, along with applications currently under development. It is our desire to stimulate speculation and development of current high performance graphites and their applications as well as ideas for new high performance products and applications. First, a little background about the process. The technology was developed through a concentrated R&D effort which culminated in 1976 in the construction of a unique furnace capable of continuously processing tonnage quantities of granular carbons at temperatures in excess of 2,500 degrees C. This process is capable of refining various carbonaceous raw materials, including natural graphites, to levels of purity and consistency that were previously unattainable in commercial quantities. Carbon contents in excess of 99.9% are currently being produced on a continuous flow-through basis. Since beginning operation in 1977, this plant, located in Hopkinsville, KY, has been expanded in stages to its present capacity of producing over 45,000 tons of purified graphites and graphitic carbons per year. In addition to the purification process, the technology used allows the introduction of selected elements into the carbon/graphite structure to provide additional benefits. Elements of interest include boron, silicon, copper, iron and rare earths. The characteristics of and applications for some of these products will be discussed later.

Jan 1, 1990

By G. Włoch, E. Rudnik

The oxide fraction of industrial zinc ash was characterized in terms of chemical and phase composition, leaching behavior in sulfuric acid solutions, and leaching thermal effect. The waste product contained about 68 percent zinc (Zn), 7 percent chlorine (Cl), 2 percent aluminum (Al) and less than 1 percent other metals, such as iron (Fe), manganese (Mn), calcium (Ca) and silicon (Si). It consisted mainly of zinc oxide contaminated with metallic zinc and zinc hydroxide chloride. The dissolution of metals from the zinc ash was determined for solid-to-liquid ratios ranging from 100 to 500 kg/m3, acid concentrations of 10 and 20 percent, and temperatures of 20 and 40 °C. The best result — 130 g/dm3 Zn(II) at 95 percent zinc recovery — was obtained at a solid-to-liquid ratio of 200 kg/m3, sulfuric acid concentration RI SHUFHQWDQGLQLWLDOWHPSHUDWXUHRI ƒ& 7KH¿QDOVROXWLRQVZHUHFRQWDPLQDWHGPDLQO\E\0Q ,, DQG)H ,,, ions, but the presence of cadmium (Cd(II)) and lead (Pb(II)) ions enabled electrowinning of zinc of about 99 percent SXULW\DWKLJKFXUUHQWHI¿FLHQF\RI WR SHUFHQW /HDFKLQJRIWKHPDWHULDOZDVDQH[RWKHUPLFSURFHVVZLWKUHDFWLRQ heat of about 520 kJ/kg