Search Documents

By Akira Ishikuro, Masamichi Shintaku, Futoshi Kusumoto, Takeshi Kudo

"The Bankei-Kitanosawa tunnel that is located in Sapporo, Hokkaido, Japan includes a 450m long section near the arrival point where mudstone which can liquate out natural hazardous materials such as arsenic and selenium exceeding the tolerance stipulated by country as well as weathered mudstone and unconsolidated sedimentary rocks with small overburden and the competence factor less than 1.0 are present. The mucks containing hazardous materials were disposed into the waterproof branch tunnels created from the inside of the main tunnel. The full face early ring closure method was employed to ensure the stability of the tunnel in the low strength rock masses having no stand-up time. As a result, the waterproof tunnels branching off the main tunnel can manage water tightness so as to ensure safety and relief against environmental risks of the hazardous materials. It is also demonstrated that the full face early ring closure method enable construction of the tunnel with a small overburden in the low strength rock masses. INTRODUCTION The Bankei-Kitanosawa tunnel includes a 450m long section near the arrival point where mudstone which can liquate out natural hazardous materials such as arsenic and selenium exceeding the tolerance stipulated by country as well as weathered mudstone and unconsolidated sedimentary rocks with small overburden and the competence factor less than 1.0 are present. In order to overcome the restrictions, the hazardous materials were designed to be disposed into large cross section waterproof tunnels which were newly designed and constructed in high strength and hazardous material free Andesite. The lining for the tunnels was composed of with shotcrete. In addition, full face early ring closure (Sato et al., 2013) was employed to stabilize the tunnel so as to enable safe tunnel excavation in low strength rock masses where a ground arch is deemed unachievable. This paper presents the safe disposal method of mucks which are likely to liquate out natural hazardous materials as well as the full face early ring closure method and its mechanical characteristics."

Jan 1, 2016

By S. S. Peng

High horizontal stress has been well recognized as a significant factor in roof control. It can adversely affect roof stability if the panel is designed improperly. Mining experience has shown that it can cause a cutter roof. The effects of high horizontal stress on roof stability depend on many factors such as magnitude and direction of the maximum principal horizontal stress, ratio of the maximum to minimum principal horizontal stress, structure and mechanical properties of the immediate roof and mining sequence. However, little is known about the intrinsic mechanism of high horizontal stress effect on roof stability except some conceptual explanations. In order to design a stable entry, the redistribution and concentration of high horizontal stress around the openings must be fully understood. Using the 3-D finite element analysis technique, this paper presents the redistribution and concentration of high horizontal stress field for a three-entry system with different orientations of horizontal stress. Based on the horizontal stress redistribution, possible roof failure for different orientations of horizontal stress is analyzed.

Jan 1, 1996

By R. A. Haney

The Mine Safety and Health Administration (MSHA) has conducted studies both in coal and noncoal mines to evaluate methods for sampling and separating diesel particulates from mineral dust aerosols. The agency is investigating size separation techniques to distinguish between diesel particulate and respirable coal mine dust. Additionally, ashing techniques have been used to distinguish diesel particulate from mineral dust in metal and nonmetal mines. As part of these studies, personal exposures to diesel particulate for various mining occupations have been measured. This paper describes the measurement techniques and summarizes the exposure levels for various underground mining operations.

Jan 1, 1990

By C. A. Carroll

In February of 1989 the Mission Complex of ASARCO Incorporated completed an expansion of its concentrator, raising the base mining rate from 25,900 TPO (28,500 STPD) to 37,200 TPO (41,000 STPD). The expansion was accomplished by extending the twelve existing Mission ball mills in length, by installing the grinding circuit from Asarco's idled Sacaton Concentrator along with various auxiliary equipment, and by modifications to the flotation circuit and water systems. This paper will give a brief history of the consolidation of the ore body which made the expansion possible and explain the various parts of the expansion.

Jan 1, 1990

By N. O. Lotter

Studies investigating the evaluation errors in laboratory scale flotation tests for platinum-bearing Merensky Reef in the Bushveld Complex, South Africa, have constructed a quality control model to assure a 95% confidence in the attested data. Specialized knowledge of the mineralogy of the platinum-group elements (PGE), together with acquaintance of evaluation models, validate a systematic checking of the sub-processes of the testwork. These include determination of minimum mill feed sample size, assay head reference distribution, mass balance checks, and specialized sample preparation of flotation test products prior to analysis. A flow schematic of this quality control model is proposed, with an example of test data that produce an error in the metal balance of 0,2% after rejection of outlier data.

Jan 1, 1995

By R. J. Sweigard

Many states are considering the need to establish or modify policy relating to the disposal of coal ash. One of the primary concerns is the impact of leachate from the ash disposal sites upon groundwater and nearby bodies of surface water. A detailed site investigation was conducted at a coal ash disposal facility associated with a power generation station. The disposal site is situated alongside a major river. Monitoring wells were installed and soil samples were taken for characterization. Groundwater models were used to simulate migration of leachate from the disposal site toward the river. Such models could be used potentially to verify regulatory compliance. This paper addresses the validation and adaptability of these models to this case and their usefulness as possible tools to be used in future environmental audits.

Jan 1, 1992

By X. Song, Q. Zhang

"The development of fracture zones in surrounding rock mass has significant impact on the stability of underground mine roadways. Detection of the fracture zones is of compelling importance for maintaining roadway stability as well as for safe and speedy excavation of the roadways. This paper presents a study conducted at Dong Bao Wei underground coal mine, where the roadways were developed in diabase rock mass. The roadways suffered severe damages, including sloughing and excessive floor heaving. The borehole imaging technique was applied in the study to observe and detect fracture zone development surrounding the roadway openings. Based on the borehole imaging studies, new roadway support systems were proposed to improve the stability. INTRODUCTION At the Dong Bao Wei Coal Mine three main roadways of the west wing were excavated. The three roadways had semicircle arch cross sections and were at a depth of 650 meters, each being about 750 meters in length. The roadways were driven through a section of thick diabase intrusion, which was softened by water with reduced strength and may turn into powder form under weathering. Site investigation indicated that the roadways in diabase intrusion zone were badly damaged due to severe deformation, and very serious roadway sidewall sloughing and spalling accompanied by severe floor heave often occurred.(Figures 1 and 2) In order to ensure the normal use of the roadway, undercuts were excavated. However, this operation seriously affected the roadway construction progress and increased the amount of roadway support operations as well as the roadway maintenance costs. Furthermore, a roof fall accident occurred in nearby drilling site. The investigation indicated insufficient support provided for the roadways which imposed significant safety hazards and would have serious impact to mining production and subsequent mining activities.The support of the main roadways is a critical task and is the focus of the underground opening excavation work at the mine, since more than 40 years of service life is required from these main roadways. For these roadways, large cross sections with high degree of stability and minimal amount of deformation should be maintained. Therefore, providing sufficient and appropriate roadway supports is of significant importance to the coal mine. In this paper, in order to optimize the roadway supporting system, studies were carried out on the geological structures, lithological characters, roof bolt anchoring features and suitable anchoring layers. The studies were aimed at ensuring the stability of mine roadways, reducing the roadway maintenance costs and providing a safe mine passageway for orderly production and progressive development of the mine"

Jan 1, 2016

Dynamic permeability is a significant hydrologic condition associated with in-situ leaching at the Cyprus Casa Grande operations. Several factors contribute to changes in the permeability conditions. They are: 1) hydraulically induced fracture development, 2) geochemical changes during leaching in the rock matrix, and 3) changes in the relative degree of saturation of the deposit. Dynamic permeability conditions were evaluated using available pressure and flow rates from the 58 injection and recovery wells obtained over one year period. A finite element, 2-D hydrologic model called INVERT which is designed to estimate aquifer parameters under transient and steady state flow conditions was used for the investigation. The permeability conditions during 7 different steady state intervals throughout the one year time frame were determined. The results confirm that big changes in permeability occur as a function of time as well as a function of injection pressure condition.

Jan 1, 1991

By O. D. Staman

The risk assessment project examines the likelihood of inorganic contaminants from copper dump-leaching operations to contaminate domestic water supplies. The project examines contaminant transport by modeling contaminant movement from the base of a leach pile through the unsaturated zone and into the saturated zone. The modeling effort is unique in that it models infiltration, contaminant transport in the unsaturated and saturated zone combined with geochemical modeling of the unsaturated zone. The project incorporates probability theory to reflect the uncertainty of hydrogeologic parameters.

Jan 1, 1994

By S. Dereski, G. Chancellor

"INTRODUCTION Barrick Goldstrike underground mine is located in Northern Nevada on the Carlin trend. The underground mine produces approximately 1.5 to 1.8 million tons a year and approximately 400,000 ounces of gold a year. The mine is comprised of two main mining methods, underhand drift and fill and long hole stopeing. The mass blast project stated in 2012 as Value in Use project between Barrick, Southwest Energy and Orica, the goal of this project is to be able to blast an entire drilled stope in one blasting event instead of taking multiple blasts. This will improve productivity by eliminating intermediate blasts, reducing additional blast time, eliminate drill hole cleaning due to the previous blast. Project implantation started in the fourth quarter of 2013 and mass blasting has been common practice throughout all of 2014. STOPPING PRACTICE AT GOLDSTRIKE BEFORE MASS BLAST PROJECT The production from the Goldstrike mine is approximately 70% from stopes. The timely completion of all stoping blocks is imperative to maintaining the plan, delays in the execution of any particular block can have detrimental ripple down effects as neighbouring stoping blocks become delayed. Before the implementation of this project the standard practice for Goldstrike was to: 1. Drill the entire stope 2. Blast a bottom shot, normally between 10 feet and 20 feet off the bottom of the slot rings. This would be mucked out before the next shot 3. Blast a pull through shot, this included the raise and one or two production rings. Again mucking this out before the next shot 4. Blast production rings, one or two more blasts depending on stope size. In most cases between each of these blasts the holes in the other rings of the stope would have to be cleaned. This meant either cleaning manually using air and water, or mechanically cleaning with a bench drill. In many cases this resulted in delays in completing the stoping block."

Jan 1, 2015

By Dirk van Zyl

Pad construction costs can impact the overall economics of heap leach projects. Pad construction costs for single-and double-lined pads, using various designs, are listed for a typical small and large project. Double-lined pads are now more often required by regulatory agencies. Unless such designs reduce the risk of site specific contamination significantly, the extra costs cannot be justified from an economical viewpoint. Specific attention is given to the short project life (typically five years) of heap leach projects. A few numerical examples are presented to demonstrate the overall economic impacts of these costs on economic parameters.

Jan 1, 1990

By J. K. Grunig

A process consisting of leach, continuous countercurrent decantation, resin-in-column ion exchange, evaporative crystallization of beryllium sulfate, and decomposition of the sulfate was developed for Spor Mountain, Utah, ores. The process is metallurgically sound, has a minimum of process steps, and is applicable to a wide variety of beryllium ores. The most novel aspect of the process is a resin system of ion exchange which is highly selective for beryllium and which rejects substantially all impurities except for minor amounts of aluminum, magnesium, fluorine, and sulfate in addition to beryllium. The oxide from sulfate decomposition meets specifications of potential users.

Jan 1, 1982

By E. Hsieh

Proximity detection in the open pit mine can be used effectively as an operator assist strategy which improves digging production through enforcement of best practices, although it is normally thought of first as a safety tool, and second as a step toward full automation when combined with object avoidance.

Feb 23, 2014

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By Martin H. Stanczyk

In recent, years the demand and consumption of finely ground industrial minerals has substantially increased for such uses as fillers and chemically reactive components. The size, specifications for these types of industrial mineral materials vary to a great extent and depend on the particular end purpose' and on the physical properties of the mineral itself. Size reduction of industrial minerals usually is obtained by conventional crushing and grinding methods. However, some specialized milling techniques have been developed for producing these minerals in extremely fine particle size ranges. During recent years the Bureau of Mines has been investigating an attrition grinding method to produce ultrafine subsieve-size mineral particles. The Bureau developed process, which has been patented,2 comprises the intense agitation of a slurry composed of the material to be ground, a relatively fine granular grinding medium, and a suspending fluid. The process has been shown to be effective for the comminution of kaolin in the particle size range of 2 microns and finer on a batch3 and continuous basis.4,5 This report presents the results of batch tests made to determine the effectiveness of the attrition grinding process for comminuting commercial products of (1) mica, a tough lamellar material, (2) fluorite, a brittle intermediately hard material, and (3) barite, a relatively soft, massive material.

Jan 1, 1967

By F. A. Campbell

This paper reports on mineral facies, ore textures, distribution of iron in sphalerites, and fractionation of sulfur isotopes in the Anvil ore body, Yukon Territory, Canada. Because the detailed structure and stratigraphy, both regional and local, are being studied by the geological staff at the mine and members of the Geological Survey of Canada, these topics will be discussed only briefly. The results of our study of the Anvil ore body have implications on theories of the genesis of ore deposits of this type, and these will be discussed. The Anvil ore body is the largest and most significant of three lead-zinc discoveries in an area of the central Yukon where major lead-zinc deposits were unknown only twenty years ago. The Vangorda deposit consisting of 22 million tons was discovered in 1953, followed in 1954 by the Swim Lakes deposit consisting of 10 million tons. The Anvil deposit, which consists of three ore zones, was discovered in 1964. The total reserve at Anvil mine is 63.5 million tons, with an average grade of 3.4% lead, 5.7% zinc, 0.16% copper and 1.2 ounces of silver per ton. This study is concerned primarily with the number one ore body which is about 2,400 feet long, up to 1,100 feet wide and 300 feet thick.

Jan 1, 1973

By S. Makni, F. Wang, A. Rosa, B. Klein, C. Saud, R. McIvor, A. Kumar, C. Gagnon, D. Gong

In response to the Natural Resources Canada “Crush It Challenge”, Corem partnered with the University of British Columbia and led a project to develop and demonstrate the use of high-pressure grinding to replace the workhorse of the industry, wet ball milling, with high-pressure grinding. Two plant case studies, a small tonnage gold recovery operation, and a large tonnage copper recovery operation, were carried out. Plant circuit performances were compared to pilot plants operated on the same circuit feed set up to represent the novel equipment and flowsheet that was developed to produce separation circuit feed. Numerous obstacles to industrial implementation of highpressure grinding in this role which were recognized at the outset of the work were successfully addressed. In both cases, comminution equipment energy savings alone, and final stage total circuit energy savings, exceeded 60% and 50%, respectively. Downstream mineral separation performance was the same or better.

Mar 2, 2022

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 1998

By H. B. Miller

By its nature, underground metal mining is unlike any other business in the industrial sector. Operations are continuously exposed to economic risk as a normal consequence of mining due to uncertainties associated with the? deposit, excavation, and ever changing political, regulatory, and market conditions. Out pacing advances in productivity and technology, these conditions have contributed to the steady decline of underground hardrock mining in the United States. This paper investigates the trends and major factors believed to be responsible for this decline. Special consideration is given to changes in direct operating costs, labor productivity, and production capacity.

Jan 1, 1995

By K. C. Corin, B. McFadzean, J. G. Wiese

The Bushveld Complex of South Africa contains almost 90% of the world’s reserves of platinum group minerals (PGMs). In the flotation of PGMs, there are significant challenges arising from the need to treat ever-decreasing grades of the relevant ore deposits. The major challenge in the flotation of these ore bodies is the control and management of the gangue minerals, particularly silicates such as orthopyroxene and plagioclase feldspar which are often rimmed with talc which makes them naturally floatable. It has been shown that various polysaccharide depressants such as CMC and guar have different properties in terms of depressing the gangue minerals. Since the PGMs are often associated with sulphides, copper sulphate is widely used as an activator in PGM flotation but can inadvertently activate the gangue minerals and reduce the recovery of PtTe2 which accounts for up to 40% of the Pt in the Platreef ore body. Depressants also reduce the mass of solids reporting to the froth and can thus destabilize the froth. This effect on the froth can be mitigated by using higher frother dosages or water of higher ionic strength. In summary due care needs to be taken to carry out site test work to develop an optimum ratio of collector, frother, activator and depressant to ensure that the highest grades and recoveries of the PGEs are obtained while reducing depressant dosage as much as possible. Chromite recoveries can be reduced through the application of gravity separation or reducing entrainment through reduced water recovery. INTRODUCTION The Bushveld Complex located in the north of South Africa contains the world’s largest deposit of Platinum Group Minerals (PGMs) (1). The so-called upper Critical Zone of the Complex hosts the largest concentration of platinum group elements (PGEs) in the world. The Zone hosts the Upper Group Chromitite No.2 (UG2) reef and Merensky Reef as well as the Platreef mineralization of the northern limb of the Bushveld Complex. The Merensky pegmatoid Zone contains the base metal sulphide grains and associated PGMs. Of particular importance to the topic of this paper is the occurrence in these reefs of various gangue minerals. The Merensky Reef consists predominantly of orthopyroxene (~60%), plagioclase feldspar (~20%), pyroxene (~15%), phlogopite (5%) and occasional olivine. Secondary minerals such as talc, serpentine, chlorite and magnetite have widespread occurrence. Of these, talc is the only mineral to show significant natural floatability (2,3). Although present in small amounts talc is closely associated with pyroxene and imparts significant floatablity to the high concentrations of pyroxene present in these ores (4). The base metal sulphides consist predominantly of pyrrohtite (~40%), pentlandite (~30%) and chalcopyrite (~15%). The major platinum group minerals are cooperite (PtS), braggite [(Pt,Pd)NiS], sperrylite (PtAs2) and PGE alloys. The UG2 consists predominantly of chromite (between 60 – 90% by volume) with lesser silicate minerals (5 – 30% pyroxene and 1 – 10% plagioclase). Other minerals present in minor concentrations, can include silicates, oxides and base metal sulphides. Total PGE varies by locality but on average range between 4 and 7 g/t. The PGMs present in the UG2 Reef are highly variable, but generally the UG2 is characterised by PGE sulphides such as laurite (RuS2), cooperite (PtS) and braggite [(Pt,Pd)NiS. The base metal sulphides consist predominantly of chalcopyrite, pentlandite and pyrrhotite. The Platreef is located in the northern limb of the Bushveld Complex. This reef consists of a complex assemblage of rock types, with pyroxenites, serpentinites and calc-silicates being the most abundant. Base metal mineralization and platinum group element (PGE) concentrations are found to be highly irregular, both in value as well as in distribution. The predominant platinum group minerals (PGM) in the mined area of the Platreef are the PGE tellurides, alloys, arsenides and sulphides. T

Jan 1, 2019