Search Documents

By Parris A. Lyew-Ayee

This paper is the first preliminary report on the bauxites and terra rossas of the Caribbean. It concentrates on the islands of the Greater Antilles, and for reference purposes the Yucatan Penin- sula is included. At this point, observations made in Jamaica, Haiti, and the Dominican Republic are compared with reported information on Puerto Rico, the Bahamas, Cuba, the Cayman Islands, and the Yucatan Peninsula with regard to occurrence, as well as physical, chemical, and mineralogical composition. From this, an attempt is made at classifying the types of bauxites in the Caribbean, indicating the best reserves estimates, and the process ability of these bauxites. Some suggestions are also provided to fuel the controversy over the likely source material(s) or origin of the Caribbean bauxites.

Jan 1, 1984

By D. Scott Scovira, Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1 ms increments up to 1500 ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits.

Feb 1, 2024

The 25th Peruvian Mining Convention (Convención de Ingeneieros de-Minas del Perú) was held Sept. 10-14, 2001, in Arequipa, Peru. The biennual meeting, sponsored by the Peruvian Institute of Mining Engineers (Instituto de Ingeneiros de Minas del Peru), is designed to showcase the Peruvian mining industry and to ?promote progress in the national mining sector.? The convention consisted of technical sessions, forums, field trips and social activities. The technical sessions featured 80 papers selected from more than 200 papers submitted. The well-organized 2001 meeting was held at the Tecsup Institute of Technology of Arequipa. The meeting was held in conjunction with Exposición Technologica Minera (Extemin), a mining trade exhibition. The2001 Extemin had representatives from more than 400 companies in attendance. In addition to the many Peruvian companies present, the trade exhibition featured pavilions representing the United States, Canada, Germany, Australia and Chile. Registration at the 2001 meeting was about 3,300, a conference record. The theme for the 2001 meeting was Mining: Society and Development. Mario Brescia was chairman of the organizing committee. He said in his opening remarks that ?this year?s meeting seeks to emphasize the commitment on the part of the [mining] companies to treat our natural resources responsibly, controlling any adverse impacts and giving priority to group benefits.? Consistent with this theme, many of the technical papers stressed environmental and social responsibility. Many successful examples of environ-mental and social responsibility on the part of the mining industry were presented in the technical sessions.

Jan 1, 2001

By Ratnakar Singh, Raj Kishore, Kisor Kumar Sahu, Ranjeet Kumar Singh, Ganesh Chalavadi

The Falcon concentrator is capable of separating minerals in fine size classes based on their differential density. Separation of mineral particles depends upon the fluid flow characteristics and relative movement of particles in a fluid. In the present study, a fluid flow characteristic inside the Falcon concentrator was established through experimentation and modeling. The Falcon concentrator has two fluid entry points: (a) Fluid entering through gravity assisted feeding system and (b) Fluid entering through the fluidized hole on the concentrator wall. In order to identify the role of fluid entering the concentrator, a tracer was injected into the system. As per the tracer based experimentation, it was established that fluid entering through the gravity based feeding system is responsible for thin flowing film formation in the stratification zone where particles are stratified based on their relative density. The momentum balance and continuity equations were simplified for a high centrifugal force field, and the fluid velocity profile was estimated inside the thin flowing film. Estimated fluid flow profiles will help to simulate the particle trajectories inside the Falcon concentrator. The influence of rotational speed, fluid flow rate, and cone angle on the fluid velocity profile were investigated. Fluid thickness over the concentrator wall is also estimated, and it is typically of the order of ~150–200 μm.

By N. L. Wesis

General History The first jaw crusher in the US was patented about 1830, but the Blake crusher that has maintained a substantial advantage over other types was invented in 1858 by Eli Whitney Blake. For going on 150 years the jaw crusher has been an invaluable machine; even today, when gyratory crushers have assumed most of the burden of crushing large tonnages of large rock and ore, the jaw crusher has a firm place in the mining industry. It is interesting that soon after the invention of the Philetius Gates gyratory crusher in 1881, a contest between the first No. 2 Gates and Blake jaw crushers of equal gape showed the gyratory to be 3.2 times as fast. This foretold a day not far in the future when the jaw crusher would not be adequate on the largest jobs. In his Textbook of Ore Dressing (1909) R. H. Richards recom¬mended that the word breaker be used for all machines breaking to relatively large sizes (say to 5 in. or greater), and crusher be used for finer work. Even in the 1968 US Bureau of Mines dictionary of mining terms the work breaker is defined by Richards in this context. However, in modern US usage it is nearly limited to coal breaking. Over the years the jaw crusher has been developed in a variety of forms but it appears today in these three general forms: (I) Blake type, (2) Dodge type, and (3) single toggle (or overhead eccentric) type. All of these crushers have a fixed jaw and a moving jaw, between which the coarse rock fragments are intermittently caught and crushed. The three types are differentiated by the manner in which the movable jaw is moved in relation to the fixed. Types The Blake-type crusher is shown in cross section in Fig. 1. The simplicity and strength that have made it first among jaw crushers are evident. The movable jaw is suspended from a cross-shaft at its upper end, this shaft being carried in bearings on the sides of the frame. The actuating mechanism consists of an eccentric shaft, also supported in frame-mounted bearings, which imparts through a pit¬ man and a pair of toggles a reciprocating motion to the bottom of the swing jaw, the return movement being effected by several spring¬loaded rods. The whole is built into a box frame with the crushing chamber at one end. As in all jaw crushers, the eccentric shaft is equipped with a heavy flywheel that maintains an even speed through¬out each stroke. The Dodge-type crusher illustrated in Fig. 2 is simple, mechani¬cally. Its movable jaw, being pivoted below the discharge opening, has minimum movement at crusher discharge and maximum at crusher feed. Because the choke point coincides with the point of least motion, these crushers are of relatively low capacity, and the rapid action in the feed area gives the machine the advantages of large reduction ratio and closely sized product. Thus, it fits well into low-capacity operations like sample reduction. Besides low capacity, its principal disadvantages are tendency to pack and make fines. The single-toggle or overhead-eccentric type of jaw crusher (see Fig. 3) has gained in usage, starting as a modification of the Dodge idea in that the greatest movement of the movable jaw occurs at the top, and being gradually improved and strengthened to its position today where it covers just as wide a field of application as the Blake type from the standpoint of feed opening. The motion of the movable jaw is the result of the circular motion of the eccentric shaft at the top of the swing jaw combined with the rocking action imparted to the bottom by the inclined toggle plate. Because of light weight and mechanical simplicity, it is economical in small mills and portable plants where the rock is not as tough and abrasive as to punish the machine with excessive impact from shocks, or excessive wear result¬ing from the pronounced vertical component of motion.

Jan 1, 1985

By William P. Blacutt

This paper examines Bolivia's General Environmental Bill recently passed by Congress: a multi-purpose law with two primary objectives: a) the protection and conservation of the environment, and b) the promotion of sustainable development. In this law, environmental benefits are emphasized by stating general principles, not by attempting to define the means. Regulations are left to the writing of subsequent complementary codes. This paper shows that much of the controversy surrounding the legislation disappears when it is seen as guide rather than an operational part of Bolivia's industrial policy. In essence, the law addresses recent environmental awareness in a region more anxious than ever to speed economic growth.

Jan 1, 1992

By R. J. Miller

Rock strata, natural and mining-induced stresses, and structural features can combine to create dangerous instabilities in or around longwall panels. Rock noises and properties variations associated with local stress systems can be used to characterize developing instabilities. Through a learning process at a particular mine, guidelines can be developed to allow the determination of relative risk and timing of a potentially disastrous instability. Once a dangerous instability has been identified, operational modifications can be employed to get through the instability, or active measures such as destressing can be used to mitigate the instability. This paper will discuss how an integrated monitoring system and associated data processing can be used to develop a hazard prediction capability for a longwall mine.

Jan 1, 1996

By R. L. Pearson

The 1987-88 Denver Brown Cloud Study was performed to determine the sources of the particle cloud which forms over Denver each winter. The study was organized under the leadership of Colorado Governor Roy Romer , EPA Region VIII and the Greater Denver Chamber of Commerce. The study was sponsored by over 40 organizations representing governmental agencies, the natural gas industry, the coal industry, utilities, oil companies, railroads, the motor vehicle industry, and other Denver area companies and organizations. The cost of the study was $1.5 million which was raised almost entirely from private sources. The study team was headed by Dr. John Watson of the Desert Research Institute of the University of Nevada. Dr. Watson is a recognized expert in conducting studies of this type.

Jan 1, 1990

By N. B. Aughenbaugh

The People's Republic of China has 582 Gt (641 billion tons) of proven coal reserves. At present, 576.5 Mt (635.5 million tons) of coal are mined a year which makes China the third largest producer of coal in the world. Underground mining accounts for 95% of the total production. This paper will discuss the coal districts, coal types, jurisdiction of coal mining, and methods of underground mining. The article also will outline China's objectives in future planning and development of its coal reserves.

Jan 1, 1982

By Miguel Angel Banuet Rodriquez, Hector Conceso Aragon

"Construction of the longest road tunnel in Mexico is part of Acapulco’s alternate roadway to the scenic roadway project. This article provides a brief summary regarding details of the construction since the project began. Work was done by skilled engineers and Mexican workers that includes outstanding execution of the work in an urban and tourist area. This project will have a strong impact on the steady development of the port of Acapulco.Project locationAcapulco’s Alternate Roadway Project is currently under construction in the city of Acapulco, located in the Guerrero state of Mexico. It is an 8-km (5-mile) long roadway that starts at the Icacos neighborhood, heading toward Acapulco’s airport, crossing a drill-and-blast tunnel that is 3,160 m (10,350 ft) long under Veladero Park, a mountainous area. The tunnel overburden reaches a depth of 380 m (1,250 ft) approximately at the central point of the horizontal alignment, and continues with a 4-km (2.5-mile) long elevated road to connect to the existing Viaducto Diamante toll road (Fig. 1).Tunnel construction has already been finished using two portals for drilling and blasting operations; Brisamar Portal on the west side and Cayaco Portal on the east side (Fig. 2).Geometric dataOnly two main excavation cross-sections were considered in the executive design. The first one corresponds to the running tunnel for a three-lane vehicle section, with crosssection areas between 120 and 130 m2 (1,290 and 1,400 sq ft) taking into consideration different geological and geotechnical conditions to be encountered (Fig. 3).The second one corresponds to eight emergency bays, each one 50 m (164 ft) long, laid down within the tunnel outline, located at 400 m (1,312 ft) from each one with excavation cross-sections between 156 to 169 m2 (1,680 to 1,820 sq ft), in accordance to geological and geotechnical conditions to be encountered (Fig. 4).The tunnel’s horizontal alignment is completely straight, having a small curve within the vertical alignment on Cayaco portal, because there were some differences in levels when tunnel excavation started. Tunnel slopes were designed in such a way that rainwater does not run down into the tunnel at any time."

Jan 3, 2018

By Graham A. Brown

Activities in offshore mineral exploration In Australia are increasing almost daily, at such a rate that this report will rapidly become out of date. At the time of writing, February 1967, there were no commercial discoveries of offshore minerals reported in Australia, although there has been definite encouragement in many fields. While this initial encouragement has not revealed any commercial mineral deposits offshore hopes are running high in Australia for success in 1967. Why should mineral deposits be expected offshore in Australia in the first place? The reasons are many. The minerals to be discovered also are many. The reasons are based on the history of alluvial and beach mining activities in Australia's past and at the present time, and on the physical environment of the vast Continental Shelf which surrounds the continent. A brief examination of the two primary features which are necessary before offshore mineral exploration can be contemplated should be, undertaken. Two favourable environments are necessary; firstly a Continental- Shelf to form a physical environment for the accumulation of the mineral deposits, and secondly a favourable political-legal environment to give the exploration companies adequate protection during exploration, and suitable long term arrangements for the exploitation of the deposits after discoveries have been made. Australia is well endowed with both of these.

Jan 1, 1967

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. Saki, J. F. Brune, J. W. Grubb

"Researchers at the Colorado School of Mines have studied the influence of headgate side ventilation controls near the longwall start-up room on the formation of explosive gas zones (EGZs) in underground coal longwall bleeder ventilated gobs. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) researchers developed a Computational Fluid Dynamics (CFD) model to study the formation of methane-air mixtures in the gob, start-up room, and bleeder entries. The relative change in size and location of EGZs are examined in response to ventilation controls in the headgate side bleeder entries near the start-up room. Modeling suggests that adjustments to the ventilation controls can be made to minimize the size of the EGZ. However the EGZ may form in or around active working areas regardless of the ventilation control settings. Research found regulators on the crosscuts into start-up room and first entry inby can force air into to crosscuts outby the start-up room causing more air to flow through the gob. INTRODUCTION Underground longwall mine ventilation systems may operate with either a bleeder ventilated gob or a progressively sealed gob. Bleeder ventilated gobs must meet the standards for safe operation of the bleeder system by examining bleeder system effectiveness. As defined in the United States Mine Safety and Health Administration (MSHA) Program Policy Letter (PPL) No. P13-V-12 (MSHA 2013), the pillared area or gob is “any area where a reduction in pillar size has occurred during retreat mining” and includes the “caved and broken material, the interstices within the caved material, and the open spaces surrounding the caved material.” The PPL further states that the intended purpose of ventilating the gob is “to protect active workings from the hazards of methane accumulations …” The requirements for operating a bleeder system as stated in The United States Code of Federal Regulations (CFR 2013) Title 30 §75.334(b) is to pass ventilation air though the gob “and to continuously dilute and move methane-air mixtures [from the gob] away from active workings and into a return air course …” where the concentration cannot exceed 2 percent methane (CFR 30 § 75.323). Further clarification of the bleeder system as described in the PPL states the following: “A bleeder system includes the area from which pillars are wholly or partially recovered, bleeder entries, bleeder connectors, and all associated ventilation control devices that control the air movement through the area. Bleeder entries are air courses designed and maintained as part of the bleeder system.”"

Jan 1, 2015

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

By David R. Delling

Tenneco is a large, diversified, energy-based company which has grown rapidly during its forty year life. We&apos;re the youngest corporation among Fortune&apos;s top 20 companies. Tenneco Minerals Company is the division of the Corporation responsible for nonfuel minerals exploration, development and operations. Tenneco Minerals Company is headquartered in Lakewood, Colorado. Exploration offices are in Colorado, Nevada, Alaska, and Perth, Australia. We currently operate two gold mines in Nevada and a large underground trona mine and soda ash processing plant in Wyoming. The latter has a capacity of 907 000 tonnes per year of soda ash and is the subject of my presentation today.

Jan 1, 1984

By R. Hogg, S. Chander

An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example, in development of new processes, plant and process design, plant control, problem solving, etc.

Jan 1, 1987

By A. Dell’Era, E. Ciro, C. Lupi

The indium recovery via electrowinning from sulfate baths has recently gained significant attention as it does not present toxic emissions, hermetically sealed system requirements, human health, and environmental hazards. Following previous works related to the optimization process for AISI 316L and Ni cathode, it was observed significant importance of the metal supports on the input and output parameters of the indium electrowinning process from sulfate solutions. Thus, comparing input and output parameters in both cases seems very interesting. Particularly, regarding the input parameters, the attention has been focused on the electrolyte composition, current density, and temperature, while productivity, morphology, and structure have been considered regarding the output parameters. Considering the productivity as the optimal output, the findings for Ni cathode were better than that for AISI 316L in most of the selected conditions studied. In the case of morphology, indium grains appear rounded and dendritic on the AISI 316L, while those on the Ni cathode show stratified lamellar grains. Anyway, the indium deposit obtained on Ni cathode shows bigger grains independently from the used operative conditions with respect to that on AISI 316L. Regarding the structure, it is clearly tetragonal, but preferential orientation, crystallinity, and deformation of the structure strongly depend on the metal support.

Jun 14, 2023

By Robert A. Bauer

Two basic types of subsidence occur in Illinois: pit and sag / trough. Pits develop over mines less than 165 feet deep and where relatively incompetent strata are found over the mines. Sag subsidence is found over mines as shallow as 75 feet and more generally over mines of greater depths. The percentage of subsidence and angles of draw associated with sag subsidence appear to be controlled by the rock properties at each specific site. The percentage of subsidence and angles of draw are smaller where the sites are not affected by geologic structures. An investigation to determine if a time factor based on the time interval from the date of mining to the subsidence events has shown that simple correlations with time, percent extraction, average pillar stresses, and pillar dimensions is not evident in Illinois.

Jan 1, 1982

By Charles A. Beasley, Vince Joyce, David E. Beasley, Orlando A. Gallegos, David A. Shuman, Mehmet H. Erten

COAL CHARACARISTICS AND PREPREPARATION REQUIREMENTS Preparation and Market Specifications The national ambient air quality standards (NAAQS) established by the Environmental Protection Agency in 1977 require that when coal is burned, the environmental degradation should be a minimum. For this reason, even coal containing low ash and sulfur must be used in compliance with the NAAQS. The most important pollutants resulting from the combustion of coal are ash, SO2, and NOx gases, and the particulate matter escaping with the combustion gases. The ash is the residue left after complete combustion of coal. It results from the inorganic mineral matter existing in the coal before it is burned. The SO2 results from the combustion of inorganic and organic sulfur associated with the coal. The inorganic sulfur may occur as pyrite, marcasite, or as sulfate sulfur of mostly iron and calcium. The authorities disagree in the definition of organic sulfur in the coal. However, according to ASTM Standard D2492-77,1 the organic sulfur is that sulfur occurring in the coal after subtracting the sum of pyrite and sulfatic sulfurs from the total sulfur in the coal. The NOx gases are produced from high temperature oxidation of nitrogen in the coal that is released into the atmosphere. The particulate matter may consist of fly ash and unburned coal. Selective Mining The cleaning of coal from included ash and sulfur-bearing materials should start at the working faces of surface or underground mines. This can be done by (1) mining only those seams which meet certain quality standards, (2) not mining sections of the seams which may cause deterioration in overall quality of the mined coal, and (3) using a mining method that allows selective mining of coal areas or horizons either underground or on the surface. Since these steps improve the coal quality before the coal reaches the preparation plant, they can be considered to constitute precleaning of coal. During the exploration and development stage of a mine, core and channel samples taken from the coal seam are used to determine (1) petrographic analysis and physical properties,2 (2) character of roof and floor of the seam, 3,4 (3) character and quality of impurities,5 (4) proximate and ultimate analysis, and (5) washability characteristics. However, all of these parameters are subject to considerable variation even within the same seam during the advance of the coal face. This creates a problem in meeting the market demand for coal quality if the coal is to be shipped directly from the mine. If the mining operation is large enough, special blending silos or mechanical blending systems may have to be used to provide uniform quality to the market. However, even if the coal is shipped from a coal preparation plant, prepreparation

Jan 1, 1991

By George E. Williamson, Mikiya Higuchi, Michael T. Traylor

Extensive soil conditioning was required to allow Earth Pressure Balance(EPB) tunneling on the South Bay Ocean Outfall tunnel project in San Diego, California, near the Mexican border. This tunnel extends 19,000 feet out under the Pacific Ocean and was mined through soil formations including silts, sands, gravels, cobbles, and boulders. EPB pressures ranged from 3.0 to 7.0 bar, with the maximum pressures required when mining through the highly permeable granular formations.

Jan 1, 1999

By Stuart R. Cotterill

Open cast surface mining requires blast hole drilling with many interesting facets in order to achieve mine planning forecasts. Interestingly, no single method or combination of theoretical hypothesis of mining economics is right for all conditions. On occasion mine planners introduce a project with little or no regard to drilling and blasting. Generally, drilling and blasting costs are a significant percentage of total mine overhead. One such drilling and blasting method which can be utilized to reduce overall mine expenditure is inclined or angle hole drilling. One must bear in mind, that angle hole drilling per-se mill not reduce costs, unless a set of required circumstances is met. An attempt will be made to detail when conditions of the mine design criteria dictate the use of angle drilling.

Jan 1, 1984