Search Documents

By Xiaochun Xiao, Xin Ding, Yishan Pan, DI WU, Xiangfeng Lv

Rockburst is a sudden disastrous instability of coal mass that poses a serious threat to underground exploitation of coal resources; therefore, approaches of prediction and control methods are valuable for improving mining environments. The mechanical properties and bursting liability of coal with drying, under-saturated, and saturated moisture content under uniaxial compression are investigated, and the charge induction signal during coal deformation both in the laboratory and on-site is recorded in this study. The presence of water reduces the cohesion and increases the internal stress caused by non-uniform deformation of minerals, resulting in the strength, elastic modulus, and bursting liability being weakened. The charge induction precursor main frequency band is 1–100 Hz and belongs to the very-low-frequency signal regime, and it indeed varies with the loading stage, leading to specimen failure owing to changes in amplitude and continuity of the charge pulse in both the time and frequency domains. Water inhibits the richness of charge induction and reduces the bursting liability, and the earlier the precursor appears, the more total charge emerges. Moreover, measurement results indicate that the amplitude and continuity of the charge pulse decrease over a longer time, as recorded in a coal seam with water injection, further verifying the weakening of the coal dynamic characteristics. Charge induction can be a valuable tool with which to obtain the precursors for rockburst and to aid the evaluation of water injection.

Dec 26, 2022

By C. P. Mangelsdorf, Richard A. Allwes

At the request of the U.S. Department of Labor, Mine Safety and Health Administration (MSHA), the U.S. Bureau of Mines evaluated the suitability of using tri-sets for protecting mine personnel in roof-fall prone areas. A steel-set arch provided by MSHA served as a basis for evaluating the performance of the tri- set. All tests and analyses were conducted according to the arch canopy test and design procedures developed by the Bureau. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of their experimental behavior. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri -sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that tri-sets may be considered for protection against roof falls, provided that the arch canopy design procedure is utilized for each application and that the principles underlying the design procedure are understood.

Jan 1, 1992

By J de Cuyper, N. R. Tipman, G. E. Agar, L. Laré, W. Freyberger

The flotation chemistry of the commercial INCO matte separation process was investigated. The slow cooling of Bessemer converter matte forms discrete phases of Cu2S and Ni3S2 and a Cu-Ni alloy. After magnetically removing the alloy, the Cu2S and Ni3S2 are separated by flotation at pH 12.4 (saturated lime) using diphenyl guanidine (DPG) as both collector and frother. DPG has been used exclusively in this flotation process because of its unusual selectivity for copper minerals. The surface product resulting from chemisorption of DPG onto the Cu2S was identified as the double salt Cu(DPG)2SO4,.CU(DPG)2(OH)2. The adsorption followed Langmuir behaviour up to a monolayer coverage. In the absence of DPG, the rapid adsorption of oxygen by Cu2S in flotation pulps was observed. The surface product was identified as the insoluble basic copper sulfate CuSO4.3Cu(OH)2 with the production of sulfate ion. In the presence of DPG, the oxidation reaction appears to be suppressed. The frothing properties of DPG and commercial frothers were compared. DPG is not a powerful frother. Batch flotation tests confirmed that DPG is a highly selective collector when compared to most sulfhydryl collectors.

Jan 1, 1976

By D. P. Gold

Major sources and reserves of Cb/Nb, Ta, REE, Y, Sc, Zr, Hf, Cu, apatite and vermiculite may be concentrated in primary and secondary minerals associated with different stages and depths of emplacement in carbonatite complexes and kindred alkalic intrusive rocks. Exploration targets include: apatite and pyrochlore (Nb) in the plutonic and hypabyssal core and ring-dikes: bastnaesite (REE), strontianite, barite and fluorite in hydrothermal veins and cone-sheets (subvolcanic setting): thortveitite (Sc,Y) and vermiculite in metasomatized aureoles (fenites): high grade eluvial deposits of apatite and pyrochlore, and secondary REE, Nb, Ti. and V-minerals in supergene and weathered zones.

Jan 1, 1991

By M. Modis

According to previously established theoretical analysis and under certain conditions, a critical sampling grid can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results, while based on this limit the ideal process of reproducing the original phenomenon is theoretically defined. The objective of this paper is the application of the above theory to the Klidi lignite deposit in Florina, Greece, where Public Power Corporation (Greece) has conducted a sampling campaign to estimate the deposit thickness and its heating value. Data acquired for these two variables were analysed in the space domain in order to derive their respective correlation functions. The structural analysis of the deposit generated two covariance models, one for the thickness and one for the heating value, from which the critical sampling grid was identified. The conclusion drawn is that in some parts of the deposit the sampling grid is denser than required. Finally, an optimal sampling grid is proposed in order to gain the maximum information at the lowest cost.

Jan 1, 2006

By W. Gibson Jaworek

Of increasing importance to the student of fuels economics has been the extent to which different primary energy sources can substitute for each other in the various energy markets of the nation. Knowledge of the nature and extent of fuel interchangeability can aid the fuels economist in projecting trends of energy utilization, as well as giving him a better understanding of the past and present conditions of fuel markets. It is also important to the consumer to know just how much flexibility he can maintain in his energy consuming operations. And, finally, various governmental bodies show keen interest in the degree of energy substitutability in determining public policies concerning the fuels industries. The presence of excess fuel production capacity in the United States during the early 1960's indicates that fuel interchangeability should become more prevalent in the increasingly competitive energy markets of the nation. Discussion of fuel intercompetition is almost always restricted to qualitative terms-because of the lack of comparable statistical data, between the different energy sources in geographic or "type-of-use" fuel, markets. There are exceptions, of course, such as, the excellent fuel consumption data which are available on steam electric generating plants throughout the nation. In other sectors, statistics are at best incomplete.' Inmost instances, indirect fuel consumption indicators, such as sales of fuel burning equipment, are extensively used to measure market shares of a particular fuel; however, these indicators are hard to evaluate precisely without prior knowledge of the total competitive market.

Jan 1, 1961

By Abdallah Khair, Nathalie Risso, Arie Herrera, Victor Tenorio

This study introduces a machine learning strategy to optimize icy regolith extraction from the Shackleton-de Gerlache Ridge using autonomous mining equipment. The model incorporates key parameters—distance, road gradient, vehicle load, speed, recharge logistics, and regolith water content—into a cost framework for excavation, hauling, and dumping. Regression models estimate energy and time requirements; classification predicts terrain navigability; clustering groups craters for efficiency; and K-Nearest Neighbors (KNN) determines optimal routing and scheduling. The system adapts to a six-month daylight cycle to maximize productivity and minimize costs, enabling intelligent planning for sustained lunar resource extraction under extreme environmental and logistical constraints.

Feb 22, 2026

By S. Castro, L. Gutierrez

A classification of flotation processes carried out in concentrated electrolyte solutions, e.g., seawater, is proposed using the most obvious features of these processes: low or high content of Mg2+ and Ca2+ ions, pulp ionic strength, and pH. The first distinguishable group is the processes carried out in NaCl/KCl solutions, about 0.5 M in the case of salt flotation of inherently hydrophobic minerals, and at concentrations about 10 times higher in the flotation of potash ores. In the flotation of sulfide ores, such as nickel or copper ores, with xanthate-like collectors, the xanthate collector is apparently not affected by pulp ionic strength and only adjustment of frother may be required. Content of Mg2+ and Ca2+ ions in seawater is the main difference between such systems and fresh water. The presence of these metallic ions can adversely affect flotation in the pH ranges over which these ions hydrolyse. The successful flotation of Cu-Mo ores typically requires depression of pyrite at high pH values achieved with the use of lime. However, in seawater, flotation of Cu-Mo ores requires removal of the hydrolysis products of the Mg2+ and Ca2+ ions or the use of a pyrite depressant that can be effective over the pH ranges that are much below the pH of hydrolysis. Mg2+ and Ca2+ ions also affect flotation of phosphate ores with fatty acids. In this case, the depression mechanism is not caused by precipitating magnesium hydroxides on the mineral surface but by precipitation of collector insoluble salts, and the same ions are responsible for depression in both cases. In the seawater flotation of Cu-Mo sulfide ores and phosphate ores, the practical solution involves either removal of Mg2+ and Ca2+ ions prior to the flotation or complexation with other reagents.

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the National Institute for Occupational Safety and Health (NIOSH) developed a light-emitting diode (LED) area luminaire called the Saturn and conducted a laboratory study using a Fletcher High Dual-boom Mast Feed (HDDR) roof bolting machine. The Saturn luminaire was designed to (1) enhance floor illumination to enable better detection of trip hazards in the interior spaces of a roof bolter and (2) reduce glare that has typically been an issue of concern on roof bolters. This paper reports on the results of achieving the second objective. The existing roof bolter lighting was the baseline and was compared with three versions of the Saturn luminaire relative to light intensity (100%, 75%, and 50%). Discomfort and disability glare data were obtained from 30 participants that comprised three age groups. Discomfort glare perceptions were obtained using the De Boer rating scale, and disability glare was quantified by using Mars Letter Contrast Sensitivity tests. Discomfort glare was reduced at least 3 levels with all Saturn versions. Also, a predictive model was used to estimate discomfort glare, and the results were similar. Disability glare was the least for the Saturn’s 50% intensity, and all Saturn versions had significantly less disability glare than with the baseline lighting. Veiling luminance was calculated and used as another indicator of disability glare. Veiling luminance was 28 to 42 times greater with the baseline lighting as compared with that of the Saturn lighting. Lastly, visibility levels were calculated. The Saturn versions were 4 to 6.5 times better in terms of visibility level.

By Robert B. Scott

The Dents Run Demonstration Project near Morgantown, West Virginia, was a cooperative venture involving the U.S. Environmental Protection Agency (EPA), the Water Resources Division (WRD)(1) of the West Virginia Department of Natural Resources (DNR), and the Christopher Division of the Consolidation Coal Company (CONSOL). The object of this project was to demonstrate pollution control methods and to clean up a 37.8 sq km (14.6 sq mi) watershed severely polluted by coal mine drainage. A study entitled, "Water Infiltration Control to Achieve Mine Water Pollution Control" (EPA-R-2-73-142),(2) was conducted by the Cyrus Wm. Rico Division of NUS Corporation for the grantee to determine the feasibility of utilizing remedial techniques to improve the Dents Run water¬shed. This study showed that the Dents Run watershed was discharging as much as 6,870 kg/day (15,100 lb/day) of acid; 1620 kg/day (3,560 lb/day) of iron 17,250 kg/day (38,000 lb/day) of sulfates; and 29,500 kg/day (64,900 lb/day) of total dissolved solids into the Monongahela River near Morgantown, West Virginia. This pollution was caused by the combination of borehole pump discharges from active underground mines, runoff from abandoned strip mines, and runoff from refuse dumps.

Jan 1, 1977

By R. DasGupta

The dissolution behavior of gold in ammoniacal solutions at 75°C has been investigated. The variables investigated include concentration of lixiviants, pH of the solution and various oxidants. The anodic dissolution of gold was studied in the absence of oxidants using the potentiodynamic polarization technique. The cathodic reaction of oxidants was studied on a platinum electrode. Tafel polarization tests were also performed to determine the dissolution rate. The overall dissolution of gold in ammoniacal solutions was examined using a mixed potential theory. A comparative study on the role of cupric am mine, oxygen, hydrogen peroxide, sodium hypochlorite as oxidants for the dissolution of gold in ammoniacal solutions has been carried out.

Jan 1, 1996

By S. S. Peng

In this paper, the precise definitions for a number of commonly used subsidence parameters are given. The subsidence parameters have been determined using an integrated approach for 110 subsidence cases collected in the major US coal fields. Attempts have been made to establish empirical formulae for the parameters. The results of this study indicate that some traditionally-held concepts should be changed.

Jan 1, 1995

By H. L. Lovall

Huge banks of preparation plant refuse and other non¬saleable materials have accumulated over the years in all major United States coal producing areas. These banks, esthetically and commercially undesirable, can cause air and water pollution and land reclamation and mineral conservation problems for the industry and nearby communities Although some refuse banks have been reworked to recover saleable coal, all remain and accumulation continues. Even those previously processed continue as potential hazards. Among the several problems created by refuse banks, in situ combustion is most treacherous. Of the millions of tons of major accumulations, there are at least 450 refuse banks on, fire at this time Attempts to extinguish such fires are costly, impractical and generally unfruitful. Studies are in progress to evaluate the potential of processing such materials to eliminate the combustion capability and to yield usable fuel and nonfuel products. Aspects of the study now in. development for coal refuse include: (a) evaluation of characteristics (size, sink-float, ash, sulfur and calorific value) of the coal refuse materials which are known to be highly variable, (b) development of an ignition test having significance for in situ conditions, (c) study of processing capabilities (comminution for liberation, pilot plant washing tests), and (d) investigation of potentially significant properties of fuel and nonfuel products which could be altered to enhance their market potential.. Among the latter products are lightweight aggregate, fill for mine slushing operations, construction, etc: Plans are to extend the studies to include the design, erection, and test processing of refuse with a transportable plant,; which could provide basic economic and product utilization data from several locations

Jan 1, 1964

By Susanne Pignolet-Brandom

Flash smelting products of a copper sulfide concentrate collected at successive levels in an experimental reactor have been studied by reflected light microscopy, scanning electron microscope - energy dispersive analysis and electron nicroprobe analysis. Chalcopyrite, intermediate solid solution, bornite, chalcocite, metallic copper, magnetite, iron-copper spinel, pyrrhotite, hematite, delafossite and cuprite have been identified in the product samples. The detailed reflected light microscopy study of these phases and their abundance in the samples has resulted in the identification of the series of reactions during flash smelting.

Jan 1, 1985

By LINDSAY BOTTOMER, Tassos Grammatikopoulos, Massoud Aghamirian, MARK FEDIKOW

A master composite (Master Comp) sample was prepared from three pegmatite zones from the Zoro Dyke D1 for mineralogical analysis and heavy liquid separation (HLS). The mineralogical examination was conducted on a subsample that was crushed to approximately P80 = 600 μm. The sample consists of spodumene (10.5 percent), quartz (29.3 percent), plagioclase (29.0 percent), K-feldspars (21.3 percent), micas (5.1 percent), tourmaline (2.9 percent) and Fe-Mn-phosphates (0.1 percent). Liberation of spodumene (88 percent) and gangue minerals, including quartz (89 percent), feldspars (94 percent) and micas (83 percent), is very good at this P80 . The average lithium (Li) concentration is 3.7 percent in spodumene, 2,196 ppm in micas, 1,001 ppm in tourmaline and 115 ppm in K-feldspars. Spodumene accounts for 96 percent of the total Li in the sample. The mineralogical data indicate the potential to recover spodumene by flotation with minimal Li losses due to other Li carriers. The HLS was conducted on a subsample that was crushed to smaller than 6.4 mm, with the smaller than 600 µm fraction removed from this test. The HLS results indicate it is possible to produce a high-grade lithium concentrate, with close to 6 percent Li2O, after the rejection of iron silicates with magnetic separation.

By Saverio Agresti, Giuseppe Lunardi, Donato Basta, Roberto Trapasso

"At a distance of 10 years from the first application of the Nazzano Method, the widening under traffic of a tube of an existing motorway tunnel was realized near Ancona, along the A14 Motorway in Italy. This paper describes the works for the enlargement with conventional method of the second tube, very close to that already widened under traffic.This enlargement was realized very fast, taking into account the advantages of some interesting technological improvements of the Final Design proved in the first tube.INTRODUCTION TO THE WIDENING OF EXISTING MOTORWAY TUNNELSThe widening of a twin-bore motorway tunnel usually considers the double option of creating a third bore as an alternative or closure to traffic of one of the two bores with the resulting reduction in the level of service for users.On the contrary, the extension in situ of a road, motorway, railway or underground tunnel in the presence of traffic, made possible by an inspired idea of Prof. Pietro Lunardi, enables the level of service of the infrastructure to be maintained without the need to resort to alternative routes to create new permanent or temporary bores, not always feasible because of the lack of the necessary space.This construction technique, known as the ‘Nazzano Method’, is part of the technologies refined and offered by the ADECO-RS approach to tunnel design and construction (Lunardi P., 2008) which is increasingly used in the world, leading to the industrialisation of tunnelling (meaning respect for the times and costs set out during detailed design) both in conventional and mechanised (through TBM) excavations.The first true experimentation of the ‘Nazzano Method’ was carried out between 2004 and 2007 to enlarge the two-bore ‘Nazzano’ tunnel (Italy, Milan-Rome A1 motorway) in the presence of traffic, widening it to house from two to four lanes in each direction (Lunardi P. et al., 2007). Following the success achieved in this first application, the Nazzano Method was strengthened considering all the possible suggestions arising from the previous experience and then taken up to enlarge the north bore of the ‘Montedomini’ two-bore tunnel (Italy, Bologna-Taranto A14 motorway), in situ and the presence of traffic."

Jan 1, 2016

By J. Bartrum

Kidston Gold Mines is a 14 000 tonnes per day rated operation located 280 kilometers west of Townsville in Queensland. The principle shareholder is Placer Development Limited. Kidston's orebody consists of 44.2 million tonnes graded at 1.79 g/t gold and 2.22 g/t silver. Production commenced in January, 1985, and despite a number of control, mechanical and electrical problems, each month has seen a steady improvement in plant performance to a current level of over ninety percent rated capacity.

Jan 1, 1985

The extraction and recovery of gold from copper electrorefining slimes by leaching and solvent extraction using dibutyl carbitol (DBC) has been practiced for several decades. Yet, the deportment of some common elements in this process has not been reported. The focus of this paper is to report the behavior of copper, bismuth, silver and selenium during the processing of industrial solutions by batch and continuous extraction on the laboratory scale. It was found that DBC, while an excellent extractor of gold from a highly oxidative chloride leach solution, also loads significant quantities of Cu, Bi, and Se. Silver was not present in significant quantities in the leach solution nor did it load appreciably. The deportment of gold and impurities are reported for batch and continuous operations of a two-stage extraction process using distribution ratios and separation factors.

Jan 1, 2010

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

By K. Hanna

Early identification of adverse geologic conditions and high stress concentrations during the high-speed extraction of coal using modern mechanized long wall systems is a major challenge facing the mining industry. Often, unexpected geologic anomalies that affect rock mass quality are encountered more rapidly, leaving the mine operator with insufficient time or information to deal with the changing ground conditions. The RockVision3DTM seismic tomographic system, developed by NSA Engineering, Inc., offers substantial benefits over conventional geologic/stress-detection methods and has been used successfully in coal mines worldwide. Tomographic images, produced economically and in near-real time, are easy to interpret, allowing mine operators to deal with potential hazards on a day-to-day basis. This paper focuses on the application of RockVision3DTM technology for delineating hazards caused by stress and geologic anomalies. Case studies for two bump-prone coal mines will be discussed. For example, (1) in a German deep (>1,130 m) mine, the drilling-yield method was used to verify the effectiveness of this technology in detecting stress anomalies ahead of longwalling; (2) in a Polish mine (-500 m deep), two longwall panels 4 km apart were monitored to assess structural and stress-related factors contributing to differences in mining conditions and magnitude of structural failures.

Jan 1, 1999