Search Documents

By Hans Hamrin, Bruce Kennedy

Once an ore body has been probed and outlined, and sufficient information has been collected to warrant further analysis, the important process of selecting the most appropriate method or methods for mining can begin. At this stage, the selection is preliminary only, serving as the basis for a project layout and feasibility study. Later, it may be found necessary to revise the details, but the basic principles for the ore extraction should remain a part of the final layout. With respect to the basic principles employed, relatively few mining methods are used today. For the purposes of this presentation, the principles are classified as follows: 1) For naturally supported stopes, the available methods are room-and-pillar mining and sublevel stoping. 2) For artificially supported stopes, the available methods are shrinkage stoping, cut-and-fill mining, square-set mining, and longwall mining. 3) For caving methods, the available techniques are sublevel caving and block caving. Due to the uniqueness of each ore deposit, the variations on each of these methods are nearly limitless. It is impossible to include even the major variations in this chapter; the goal of this chapter is to present the principles as a guide to the mining engineer in adapting the general methods to specific needs. The selection process described herein is intended to supply the techniques by which the candidate methods available for a given ore body can be reduced to one or two feasible approaches. The feasible approaches then can be evaluated in detail, and the particular modifications can be investigated. In describing costs and economic factors, all values herein are expressed in terms of 1978 US dollars.

Jan 1, 1982

By F. M. Benavides

The mining complex being analyzed consists of four mines and two processing plants located in an area where there are several existing modes of transportation. Figure 1 shows a map of the general layout of the four proposed mines and the two existing processing plants. The mines are identified by the numerals "I" through "IV" and the plants by the letters "A" and "B". A proposed overland conveyor would collect the product from all four mines and convey it to Processing Plant A. Alternate transportation systems are as follows: Railroad transport from Mines I and II to Plant B; Highway trucking from Mines I and II to Plant A; Off-the-road truck haulage from Mine III to Plant B and from Mine IV to Plant A. River transportation from the mines to the processing plants was not considered in this study under the assumption that the high capital investments for the loading and unloading facilities, in addition to difficult traffic problems, would make this mode of transportation unattractive.

Jan 1, 1980

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012

By Klaus Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300 and 600 °C is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies depending upon structural homogeneity, porosity and gangue quantity. Especially sinters with heterogeneous structures transmit stress to the hematite phase and this favours disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 1, 1981

By Robert J. Ramsey, N. Finkelstein, Robert D. Jeppson

Introduction The Utah Copper Division of Kennecott Copper Corporation will present its contribution to the A. M. Gaudin Flotation Symposium in four parts. The first two segments will discuss briefly the historical development of the Utah Copper Division and describe the ore body. The third segment will review the facilities and operating procedures for the Utah Copper Division's newest plant, the Bonneville Concentrator. The fourth segment describes flotation process circuitry, including molybdenite recovery procedures, at the Arthur and Magna concentrators. (The Bonneville concentrator is a crushing and grinding unit and does not have its own flotation plant). 1. Historical Development Progress through change has been the key to the successful operation of the Utah Copper Division for more than 70 years. As the original low-grade copper operation, the pressures to remain competitive and profitable have dictated the timing and extent of each change. Much of the change has occurred through technological and economic advancements in the area of ore concentration. The Utah Copper Division of Kennecott Copper Corporation had its origin June 4, 1903, when the Utah Copper Company was organized. The initial mill of 300 tpd (tons per day) capacity was built at Copperton a few miles below the present Bingham Canyon mine site. From 1904 to 1910, the Copperton mill was expanded to a capacity of 1,000 tpd, and all of the known apparatus for gravity concentration were evaluated.

Jan 1, 1976

By J. L. Coburn

The Huari-Huari ore body is located in Southern Bolivia, at an elevation of approximately 3,800 meters above sea level. The ore is a complex massive sulfide, slightly marmatitic sphalerite, in a fault fissure filled hypo- thermal vein in Paleozoic shales and quartzite-altered sandstone. The sphalerite has common associations with pyrite and quartz and is frequently intricately intergrown with stannite, chalcopyrite, and pyrrhotite. The sphalerite also contains numerous inclusions of pyrite, marcasite, galena, boulangerite, jamesonite, quartz, arsenopyrite, and cassiterite. A research program was undertaken to develop a flowsheet for the recovery of separate silver, zinc, and tin concentrates by selective flotation. Based on this experimental work and subsequent flowsheet development, engineering and construction of a 500 metric ton per day concentrator was undertaken. This paper describes the process that was developed for the Huari-Huari ore and the unique aspects of the Huari-Huari concentrator.

Jan 1, 1977

By J. L. Fuller

Mine ventilation surveys were conducted by Technical Support engineers during June 1987 and September 1989 at the Dutch Creek Hine. The mine is located near Redstone, Colorado and is operated by Mid-Continent Resources, Inc. Following completion of the initial survey, several recommended improvements were incorporated into the ventilation system by mine personnel. The second survey permitted documentation of the effects of those changes on the ventilation system performance. This paper describes the processes involved in the implementation of the recommended changes. The substantial improvements in system efficiency and reduced operating costs are also described.

Jan 1, 1991

By C. D. Iles

The philosophy used in designing and writing Duval's Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). FED is a method by which predesigned pushbacks are sequenced into an optimized period-by-period design that can be directly utilized in daily operations as well as intermediate and long range planning. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system; it is in operational use.

Jan 1, 1981

By C. Flores

It is well known that manganiferous silver ores containing manganese intimately associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily for recovering copper from oxidized and oxide-sulfide ores. A new alternative process combining segregation roasting followed by flotation to recover silver from refractory manganiferous silver ores, was studied using a 23 factorial experimental design. Laboratory investigations have been conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/ton silver to study the effects of additives salt, coke and copper oxide on silver recovery. Results indicate that 79.3% silver recovery can be attained in the absence of copper oxide and 88.4% when the copper oxide content is 1.5% at '750°C, 2% salt and 1% coke and 30 minutes of roasting time. It was concluded that doping with copper oxide improves silver recovery.

Jan 1, 1994

By J. Brad Dalton, Sam Vance, Trude V. V. King, Roger N. Clark, Raymond F. Kokaly, Gregg A. Swayze, Dana J. Bove

Visible-wavelength and near-infrared multispectral image cubes for the Animas River Watershed from Hermosa, Colorado to the headwaters at Animas Forks, Colorado were acquired on June 18, 1996 using the Jet Propulsion Laboratory's AVIRIS (Airborne Visible and InfraRed Imaging Spectrometer) instrument (Green et al., 1998). These image cubes have been analyzed using the USGS Tetracorder V3.4 implementation (Clark et al., 1995), an expert system which utilizes a database of more than 300 laboratory spectra of endmember minerals and mineral mixtures to generate maps of mineralogy, vegetation coverage, and other material distributions. Major iron-bearing, clay, carbonate, and other minerals were identified along with several minerals associated with acid-generating hydrothermal systems including pyrite, jarosite, alunite and goethite. Additionally, distributions of alkaline minerals such as calcite and chlorite indicate a relation between acid- buffering assemblages and stream geochemistry within the watershed.

Jan 1, 2000

By B. Ladanyi

An adequate knowledge of the overall behavior of a rock mass at a given site is fundamental to the satisfactory design of a rock slope. The be- havior is controlled by a variety of factors, in- cluding rock type, geological structure, stress and ground water conditions. There are essentially three lines of approach that may be used to obtain information on the in-situ rock mass behavior for the purpose of the design of a rock slope: (1) Direct measurements of rock mass properties by means ol laboratory and field tests. (2) Evaluation of rock mass properties from a study of slope failure case histories and sta- tistical information on stable and unstable natural rock slopes. (3) Evaluation of in-situ behavior of rock mass by using a physical or mathematical model technique.

Jan 1, 1980

By Grover H. Emrich

Pennsylvania,, due to its location in the humid east, is fortunate to possess within its borders large quantities of water. Most of the State is drained by three major river systems-the Ohio, Susquehanna and Delaware. This abundant supply of surface water has been widely utilized throughout the State, but today other sources of water must be developed due to the increasing demands for water, die largest undeveloped source of water in Pennsylvania is ground water. Pennsylvania is also fortunate to possess extensive coal resources. These coal resources have contributed measurably to the development and prosperity of the States Coal and water's - two valuable resources - have been necessary for the development and industrialization of Pennsylvania, The State needs both resources but can no longer afford to develop one while adversely affecting or destroying the other, We are aware of the effect of coal mining on surface water, but coal mining can also materially affect subsurface water, This effect will according' to the local geologic conditions.

Jan 1, 1965

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal mining operations can cause various disturbances to surface structures ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of the travelers and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (e.g., decks, beams, abutments, etc.) are presented. A number of mitigation measures to protect the bridge structures are recommended along with an actual application case.

By R. Hogg

The sedimentation and dewatering characteristics of flocculated slurries are determined by the size and density of the flocs. Studies of the formation and growth of flocs reveal that floc size is limited by breakage of the agglomerates due to shear in the suspension. Floc density measurements indicate that there is an inverse relationship between size and density. This relationship appears to be determined primarily by the nature of the solid particles, especially the size distribution, but it appears that agitation of the suspension can lead to some densification of the flocs, in addition to breakage. It follows that both size and density can be controlled to a significant extent by regulating the physical conditions (agitation, method of flocculant addition etc.) during flocculation. The use of physical floc conditioning to control the sedimentation and dewatering (filtration) behavior of flocculated, fine-particle suspensions is evaluated in terms of its effects on floc size end density.

Jan 1, 1986

By J. R. Arnold

The problem of recovering gold from a cyanide solution has been plaguing metallurgists since the cyanidation process was discovered in Glasgow, Scotland.1 The "perfect" method has never been found and this paper will not purport to fill that gap. But we, at Gold Fields, feel that we have developed a workable, cheap and efficient method of producing a refinery - ready product that has several distinct advantages over conventional electroplating techniques. The Gold Fields replating system is presently being used at their Ortiz and Mesquite operations. In short, the system electroplates the gold out on stainless steel wool, instead of mild steel wool as is usually done, then replates the gold by reversing the current onto stainless steel plates. By doing this the steel wool can be reused many times, the gold can be scraped off the plates cleanly and quickly, the operating costs are reduced and the slag production is greatly reduced.

Jan 1, 1986

By W. Burr Bennett

The prestressed concrete industry in particular, and the precast concrete industry to some extent, are rank newcomers to the concrete construction field compared to the cement, ready-mixed or concrete masonry industries. This young industry reflects its youth and vigor in its enthusiasm, optimism and the belief that it can reach any goal it chooses to set -- and it is setting its sights high. The prestressed and precast concrete industry fully expects to become the major structural and architectural material by the 1980's. Before exploring how the industry expects to reach this goal, a brief look at the origins and the growth of the industry may be useful in an evaluation of the feasibility of this goal. It was always recognized that concrete, strong and efficient for supporting loads which cause compression, was weak and inefficient when used to carry loads which induce tension. Thus the reason for reinforced concrete in which the concrete efficiently carries the compression in a flexural member while low grade steel bars reinforce the concrete in the areas 'of tensile stress. (Fig. 1). The steel being relatively inexpensive, can passively, but quite effectively carry tensile force while the concrete carries compression. The concrete in contact with the reinforcing also protects the steel from corrosion and acts as insulation to provide a superior "built-in" fire resistance. The major disadvantage of reinforced concrete relative to its main competitor, steel, is its weight in relation to its load-carrying capacity. Reinforced concrete systems, such as waffle slabs, I-beams, thin shells, etc. ,

Jan 1, 1971

By Will B. Jamison

The most serious safety problems encountered in U. S. underground coal mines today are related to the roof bolting operation. Also, roof bolting is usually the operation which limits coal production of the section. The purpose of my paper is to review some of the research, developments, and new ideas related to roof bolting. Many of these ideas have originated at. coal mines or with manufacturers. Most of the research on fundamental improvements has been funded by, and is a part of, the excellent and broad plans of the Bureau of Mines.

Jan 1, 1977

By Nasser Madani, Yerbol Tussupbekov, Sergei Sabanov, Zarina Mukhamedyarova

A case study was conducted on a metal mine operating in Kazakhstan, in which problems were associated with use of a complicated and outdated ventilation system and its high expenses. The mine needs to reconsider its existing ventilation system and identify the risks associated with operational losses when using this ventilation system. The aim of this study was to develop an efficient risk analysis method capable of estimating operational risks and financial benefits of the existing mine ventilation system. The developed risk analysismethod considers ventilationmodelling, riskmodelling, and financialmodelling.Ventilation modelling comprises ventilation simulation and ventilation financial simulation. In risk modelling, the number of risk events occurring with the use of existing ventilation system and the operational losses during these events is estimated. Financial modelling considers operational losses and ventilation financial simulation benefits and uses a dynamic cash flow model to estimate how cost variability influences the cash flow. As a result, the improved ventilation system attains an additional NPVa ranging from 3.2 to 8.5 million US$ at the corresponding defined probability of 90%. The results of this study reveal that the developed risk analysis method can efficiently estimate the financial benefits of ventilation modelling and consider risk events and their total operational losses associated with use of the existing ventilation system. This approach provides a range of possible outcomes and helps with deciding whether the ventilation system is appropriate or whether it should be updated to better suit the project financial benefits.

Jun 3, 2020

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jason Navoyski, Jennica L. Bellanca

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos using the Unity game engine. The simulation videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories using graphic simulation. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Jun 1, 2023

Critical safety tools to locate miners underground are featured by several exhibitors at MINExpo. Communication was the buzzword for health and safety products at the 2008 MINExpo, and it is still important in 2012. Products unveiled following the Miner Act in 2006 have been upgraded and improved. Saving lives and reducing injuries through better leadership, planning and practice is the goal of every mine professional.

Jan 1, 2012