Search Documents

By Rusdian F. Kayadoe, Michael B. Hutahaean, Sandi A. Firmanulhaq

Deep Mill Level Zone (DMLZ) mine is located in Papua, Indonesia operated by PT Freeport Indonesia (PTFI) with approximately 1,500m below surface. The ore body extend 1230m width from northwest to southeast by 300–400m length east-west. The mine currently produces at full production of 80,000 tons per day until 2041. Part of the extension of current active production block and mitigation sits 225 m above the production block 1 (PB1) and 2 (PB2A and PB2B) which located in 2590L, named production block#4 (PB4W and PB4E). As the mining continues at PB1N, PB2A, and PB2B, the cave growth vertically and laterally to south perimeter of the footprint affecting the integrity of PB4W/E footprint. Currently, PB1N and PB2N are in active production whilst PB4E development continues from South against PB1N cave, as can be seen in Figure 1. A slight overlapping between PB1E and PB4E intentionally to promote cave connections between the two caves. Despite low stress model in the PB4E near existing caves, the PB4E cave propagation expected by the large strain and will be propagating in tension failure to the PB1E cave. Hence, designing the drill drives edge and first drawbell location as close as possible to the PB1E cave is necessary to guarantee cave connection. Since PB4 footprint development commenced in December 2021, there have been a substantial cave propagation observed from existing downhole monitoring. As the PB4 footprint designed perpendicular to existing DMLZ PB1 cave, adjustment of the development edge design is necessary to reflect the progression the loosening zone propagation to the South. Final life of mine design for extraction, undercut and ventilation level were decided in October 2023 considering latest update cave (fractured/ yielded) boundary. Numerical model of potential rock mass damage also aids the decision to locate the drift edge design. Predicting the cave progression impact is critical to both production at the existing active blocks and development of the new area. The use of cave shape data from year 2021–2023 gives an insight of the cave shape estimation at the end of 2024 when the undercut drift will be developed. This paper presents actual cave growth of active production blocks and its relative vertical progression impact as the result of drawing in order to plan for acceptable rate and provide mitigation once the minimum acceptable rock mass condition and minimum pillar threshold achieved.

Feb 1, 2025

By Jin Zhao, Weijie Wei, Jinwang Zhang, Xiaohang Wan, Shengli Yang

Reasonable mining-retention ratio (ratio of room width to pillar width) is vital to recovery rate and stope stability in underground mining of solid potassium salt deposits. Based on the engineering background of a solid underground potassium salt mine in Khammouan Province, characteristics of the plastic zone of the pillar, and the variation of recovery rate and stope stability under different mining-retention ratio conditions are discussed. The results show that compared with current room width (8 m) and pillar width (10 m), the optimization method of improvement of stope stability. The research results are helpful to recover as much solid potash resources as possible under the premise of ensuring the stability of stope.

Jun 25, 2024

By Fernando Jorge Dick

Artificial sulphides have been produced on the surfaces of heavy metal-oxide, minerals at elevated temperatures (1) and these sulphides gave consistently similar flotation characteristics as the respective natural sulphides. In the case of tin, the only natural tin sulphide known is herzembergite (SnS) which is found only in minor quantities, and its flotation behavior is not known. Balberyszki, Dorenfeld, and Carmi reported (2) tests with artificial tin oxide and pure cassiterite treated with hydrogen sulphide at temperatures above 750oc. They confirmed that the product could be floated in acid pulps. However, iron sulphides derived from pyrite, limonite, and hematite which are generally the major impurities in tin bearing ores could not be separated from tin sulphides under the conditions used by previous investigators. As a practical matter, if complex tin ores or complex low grade tin concentrates are to be treated by this process, it is necessary to be able to separate sulphidized cassiterite from other sulphidized minerals in the feed. The major metallic minerals, by weight, in complex tin ores are the iron minerals--pyrite, hematite, limonite, magnetite and pyrrhotite. These minerals become (or remain) sulphidized during the sulphidization process.

Jan 1, 1978

By John W. Sweeney

Florida is usually thought of as a vacation State, not a mining State, yet Florida has been the leading producer of phosphate rock in the United States for 85 consecutive years and in 1978 supplied over 80 percent of the national output and over 30 percent of the world's output. It is estimated that the Central and South Florida phosphates contain 412,800 short tons (374,000 metric tons) of U308, that 115,000 short tons (104,000 metric tons) of U308 will be contained in the wet-process phosphoric" acid procsssed in the United States through the year 2000, and that 54,000 short tons (49,000 metric tons) of U308 will be available from Florida. In 1978, two companies in Florida and one in Louisiana went on-stream recovering uranium oxide from wet-process phosphoric acid and three others started construction of U308 extraction facilities. These six companies will have the capacity to recover 2,137 short tons (1,900 metric tons) of U308 annually in 1980, which will account for about 15 percent of our domestic requirements.

Jan 1, 1979

By E. B. Fitch, D. A. Dahlstrom

Liquid-solids separation is common to practically all mineral and coal processing as the bulk of beneficiation plants employ water as the major processing vehicle. The growing usage of hydrometallurgy has increased the importance of liquid-solid separation as acidic and basic solutions result in greater amounts of colloidal solids, with their consequent greater difficulty of separation, the economic need for chemical recovery to minimize this operating cost, and the usual necessity of employing more costly construction materials. The three processing steps covered in this section have significant capital costs. Drying, particularly, has an important operating cost because of the obvious need for energy to evaporate the water or solvent. Several common factors influence all three liquid-solid separation steps. Particle Size and Size Distribution. In general, finer particles have slower settling and filtration rates. The specific surface area is increased, which means a lower solids concentration in the thickener underflow and discharged filter cake as well as a grater moisture content to be evaporated in the drying step. Therefore, overgrinding or excessive attrition should be avoided. Consideration should be given to optimum particle size consistent with entire plant operation performance and recovery. Solids Concentration. Increased feed solids concentration will generally minimize required equipment size and costs in all three liquid-solid separation steps. Most thickeners are designed on the basis of unit area required, expressed as square feet per short ton of dry solids per day (square meters per metric ton per day) which will usually decrease with increased feed solids concentration. Filtration rates also increase as the required flow through the capillaries of the filter cake decreases. Dryer capacity increases and less energy per ton of final product is required to evaporate the associated moisture. Particle Shape and Surface Characteristics. Generally, optimum shape is a spherical particle of zero porosity. As either of these factors degrade away from the desired state, difficulty increases. This is particularly true in drying, where porosity can decrease drying rate significantly if the moisture must first reach the particle surface by diffusion

Jan 1, 1985

By J. L. Francke

This paper describes the practices and methods used in a study of Time Domain Reflectometry (TDR) as an inexpensive deformation monitoring tool in underground excavations at the Waste Isolation Pilot Plant (WIPP). The WIPP is being developed near Carlsbad, New Mexico, for the disposal of transuranic nuclear wastes in bedded salt 655 m (2 150 ft) below the surface. Data collected from WIPP geomechanical monitoring are used to characterize conditions, confirm design assumptions, and understand and predict the performance of the deep salt excavation. The geomechanical monitoring program encompasses numerous geomechanical monitoring techniques ranging from inspection of observation boreholes to advanced radar surveys. In 1989 TDR was introduced as a monitoring tool with the installation of 12.7 mm (0.5 in) diameter TDR cables in the underground excavations. In 1993, a new TDR system was installed in a separate location. Based on experience with the previous installation, enhancements were implemented into the new TDR system that: 1.) extended the period of performance by increasing cable diameter to 22.2 mm (0.875 in), 2.) increased accuracy in locating areas of deformation by aligning cables with nearby observation boreholes, and 3.) improved data acquisition and analyses using a standard laptop computer, eliminating the chart recorder previously used. In summary, the results of a correlation between the TDR signatures to nearby observation boreholes and geomechanical instrumentation will be presented.

Jan 1, 1996

By Y. Pan, V. V. S. Vytla, P. Tukkaraja, R. BHARGAVA, S. Jayaraman Sridharan

Panel caving is an underground bulk mining method that utilizes gravitational force for mining massive, steeply dipping, and deep-seated ore deposits at a lower operating cost. To control dust and gas emissions entering the production level during the extraction of ore from the draw points in a panel cave, relatively negative pressure is created in the cave by installing an exhaust fan in the exhaust drift located on top of the cave. Since caving is a dynamic process, the design of an effective ventilation system is a challenging task, and therefore, estimation of airflow resistance offered by the broken rock inside the cave is critical. The complex and dynamic nature of caving also makes it difficult to predict the airflow resistance by using traditional approaches. This study investigates the effect of changes in the bulk porosity of the broken rock on the cave airflow resistance using computational fluid dynamics (CFD) approach. The results show an inverse relationship between the cave airflow resistance and the bulk cave porosity. The pressure-quantity characteristic curves presented in this paper provide valuable information for sizing and operating an exhaust fan used for a mature panel cave ventilation.

May 17, 2022

By Jeremy Cawley, Horry Parker Jr., Clint Wilson

The 5180 m EPBM drive on the Lower Olentangy Tunnel (LOT) is predominantly within glacial overburden. To connect LOT with the existing OARS deep tunnel in limestone bedrock, the upper 15 m inside diameter Vine Street retrieval shaft telescopes down to 6.7 m in diameter and extends into the karstic Columbus Limestone to a depth of 51 m, where a 104 m SEM tunnel will connect to OARS shaft 6. Pre-excavation grouting was reuired prior to lower shaft excavation to reduce potentially high groundwater inows. This paper discusses the secant pile installation, grouting program, shaft excavation, and hydrogeologic observations.

Jun 23, 2024

By S. D. Van Nort

The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc., an 81% owned subsidiary of Freeport-McMoRan Inc., lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in early 1988. Production at the open pit Grasberg deposit commenced in December 1989. The Grasberg copper-gold orebody is contained with a young igneous complex of dioritic composition which intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork.

Jan 1, 1991

By R. G. Dalbke

An increasing number of water pollution control systems are certain to be installed by many industries in the future because of new federal, state, and local government regulations, and because of the rising general concern about the deterioration of our water resources. Extensive engineering, some of it based on methods not yet developed, will be required if these new systems are to provide optimum pollution control. Capital cost, operating cost, and present and future regulatory requirements will be primary factors to be considered by engineers. This paper outlines procedures and gives examples of advanced engineering practices that have achieved efficient pollution control systems in the steel and nonferrous industries.

Jan 1, 1968

By J. E. Murphy, Y. Topkaya, R. E. Johnson, B. R. Palmer, D. K. Dysinger, R. B. Bhappu, A. E. Clark

The U.S. Bureau of Mines utilized a central composite experimental design to investigate leaching kinetics of pure chalcopyrite in the sulfuric acid-oxygen system. The six factors studied were oxygen pressures of 150, 300 and 450 PSI, leach temperatures of 35O, 65O, and 95O C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0 and 1.5, leach times of 8, 16 and 24 hours, initial acid strengths of 0.6, 1.2 and 1.8 g H,SO,/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. Chemical analysis and oxygen consumption measurements indicatedthat leaching occurs through three consecutive reactions. Temperature was the primary determinant of leach rate and solution acidity was the primary determinant of oxygen consumption, sulfur oxidation, and activation energy.

Jan 1, 1993

By Akram Marseet, Andrew J. Petruska, Rik Banerjee

Underground mine roof bolting is a crucial operation for miners’ safety and mine sustainability. Since roof bolting is a manual or human-supervised operation, miners’ safety is at risk due to dust or rock falls. Traditional machine learning algorithms have shown limitations to detecting drillable areas, mainly due to harsh lighting conditions. The authors propose an adaptive deep-learning framework for autonomous roof bolting. The proposed framework is based on implementing a binary semantic segmentation algorithm on color images to classify pixels that belong to rock from those that belong to non-rock. Significantly, the proposed framework implements deep learning semantic segmentation on images from traditional and neuromorphic vision sensors in underground mines. The performance of the proposed model shows an impressive accuracy level of at least 98% at a low number of training epochs with smooth learning curves. The high accuracy enables the implementation of autonomous roof bolting, greatly improving miners’ safety and operational efficiency while reducing human exposure to safety hazards. This research will advance the use of deep learning in mining automation and has the potential to revolutionize the traditional mining industry.

Feb 1, 2024

By Grover H. Emrich

Pennsylvania,, due to its location in the humid east, is fortunate to possess within its borders large quantities of water. Most of the State is drained by three major river systems-the Ohio, Susquehanna and Delaware. This abundant supply of surface water has been widely utilized throughout the State, but today other sources of water must be developed due to the increasing demands for water, die largest undeveloped source of water in Pennsylvania is ground water. Pennsylvania is also fortunate to possess extensive coal resources. These coal resources have contributed measurably to the development and prosperity of the States Coal and water's - two valuable resources - have been necessary for the development and industrialization of Pennsylvania, The State needs both resources but can no longer afford to develop one while adversely affecting or destroying the other, We are aware of the effect of coal mining on surface water, but coal mining can also materially affect subsurface water, This effect will according' to the local geologic conditions.

Jan 1, 1965

By Yuchen Wu, Purushotham Thkkaraja, Marek Borowski, Jie Liu, Jianwei Cheng, WANCHENG ZHENG, Yu Wang, Weidong Lu, Gang Zhao, Zhanyou Sa, Huan Yang, Yuhang Wu, Hui Wang

The abstract discusses the importance of gas drainage in coal mines for safety, environmental protection, and resource utilization. It highlights the significance of borehole sealing technology for efficient gas drainage. The study introduces a new inorganic retarding sealing material and investigates its properties, including stability, thermal stability, fluidity, and thixotropy. The material's diffusion performance in cracks is tested using a self-designed system. Field tests in a coal mine demonstrate the material's effectiveness in improving borehole sealing compared to traditional materials.

May 1, 2022

By Rudecindo S. Silo

[The principal characteristics of the process is that when applied in medium or in great degree it only needs unelaborated raw materials such as sodium chloride and calcium carbonate, or of medium elaboration, as sulphur which is found in large quantity in the North of Chili; however, the may be also applied to small copper plants provided that low cost sulphuric acid is available as a substitute for sulphur, that is, in. those plats of small capacity where large additional installations are not needed for the regeneration of the leaching solution. The method itself comprises 6 stages, namely: crushing, leaching, washing; of solutions, precipitation, regeneration of the leaching solution and fusion.]

Jan 1, 1965

By Mike Harrington, Tung Vu

The Regional Connector Transit Project is a 1.9-mile-long underground light rail system that will connect LA Metro’s A (Blue), E (Expo), and L (Gold) Lines in downtown Los Angeles. This $1.75-billion design-build project is scheduled for revenue service in Spring 2023. The project consists of 21-foot diameter twin-bored tunnels, a 300-footlong crossover SEM cavern, three new underground stations (at 1st Street/Central Avenue, 2nd Street/ Broadway Avenue, and 2nd/Hope Streets), and cut-and-cover tunnels along South Flower, Alameda, and 1st Streets. This paper, which is the continuation of our previous paper presented in RETC 2019—LA Metro Regional Connector Transit Project: Successful Halfway-Through Completion, will provide insight regarding the construction of major components, and the system integration and testing work undertaken for this complex transit project.

Jun 13, 2023

By Tony Szwilski

A correlation between the rank, ash content and coal seam discontinuities and coal strength/stiffness is discussed. Rebound hammers were used to evaluate the strength properties of two coal seams. The coefficient of variability of the rebound tests are compared with those of laboratory compressive strength tests by other investigators.

Jan 1, 1985

By K. H. McDaniel

Eight Mine Weather Stations (MWS) installed at the Waste Isolation Pilot Plant (WIPP) to monitor the underground ventilation system me helping to simulate real-time ventilation scenarios. Seasonal weather extremes can result in variations of Natural Ventilation Pressure (NVP) which can significantly affect the ventilation system. The eight MWS(s) (which previously collected and stored temperature, barometric pressure and relative humidity data for subsequent NVP calculations) were upgraded to provide continuous real-time data to the site wide Central Monitoring System. This data can now be utilized by the ventilation engineer to create real-time ventilation simulations and trends which assist in the prediction and mitigation of NVP and psychrometric related events.

Jan 1, 1997

By E. J. Ostrowski

The history of ironmaking dates back to 4000 BC when an open forge was used to produce a sponge iron from a heap of ore and charcoal. Even at this early date, man recognized the need for a fuel and a reducing agent. As time passed, man developed new methods of producing iron; however, these developments were centered on the mechanical aspects, and as a result, a furnace evolved which is now known as a blast furnace. During this period of evolution,' man struggled with the only fuel he knew - charcoal. Some 5600 years passed before any attempt was made to use coal as a fuel for the blast furnace. The use of coal had its beginning in 1619 when Dud Dudley of England first attempted its use in the blast furnace; as a-fuel and as a reducing agent. Coal charged to the top of the blast furnace was not satisfactory. The volatile matter of the coal choked the flues, and also the poor, strength qualities would not support the weight of the ore. Breaking up of the coal compacted the stock column to an impervious mass. One hundred and sixteen. years later in 1735, Abraham Darby of England introduced coke as the fuel and reducing agent in the blast furnace. The acceptance of coke as a fuel for the blast furnace was not spontaneous. As late as 1870, one-half of the pig iron product of the United States was made with anthracite coal, 30 per cent with raw bituminous coal and coke, and 20 per cent with charcoal. However, by 1910, 96.2 per cent of the blast furnace product was made with coke, 2.4 per cent with anthracite and coke admixture, and 1.4 per cent with charcoal. Coke became the standard fuel in the blast furnace. As the art of ironmaking progressed, more pig iron was produced and more coke was consumed. Coke oven capacity was progressively increased. In 1910, there existed approximately 4,000 coke ovens; in 1960 there was approximately 15,000 ovens. This increase in coke oven capacity was necessary to feed the mammoth appetite of modern blast furnaces.

Jan 1, 1962

By Francis J. Quinn

The Natural Gas Act, of 1938, which put interstate pipelines under the jurisdiction of the Federal Power Commission, did not place a protective competitive shield around such companies - nor does any provision of the act guarantee them a profit. Natural-gas pipelines are competitive with each other and also with the coal and oil industries. Gas distributing companies must compete not only with the coal and oil industries, but also with the electric industry. Natural gas has captured markets from oil, which had taken them from coal. Oil men contend that gas prices have: been, held to an artifically low level by regulation. The electric industry is moving into the space-heating market, which pleases the coal people because the coal industry's largest customer since losing the railroads to dieselization has been the electric companies. The coal industry is attempting to monopolize the industrial and electric generating market through government intervention, and this is being done under the guise of concern for the national welfare through advocation of a "National Fuels Policy purporting to, further the cause of fuel conservation. Such a policy is contrary to American principles and would result in the individual's loss of freedom of choice and ultimately, in less reserves of preferred fuels because of diminished exploration efforts.

Jan 1, 1961