Search Documents

Sedimentation is used to clarify process effluents or to thicken process slurries. The sedimentation cycle of a suspension is presented as a settling curve. This curve is simply a plot of the height of the interface between the settled suspension and clear liquor versus time. Figure 1 shows a series of graduate cylinders which contain a suspension at various stages in its settling cycle. Cylinder 1 shows the suspension completely mixed at time zero. After a brief period of time (see cylinder 2), the suspension is observed to settle from its initial height Ho to height H1, leaving behind a volume of clear (or turbid) liquor, called the supernatant. The interface between the supernatant and suspension is termed the mud line. It is also possible to distinguish at the bottom of the cylinder a layer of sludge representing solids which have settled from the suspension. The interface between it and the suspension is called the sludge line. The sludge line moves upward in the cylinder.

Jan 1, 1992

By H. Sevim

Three transportation and handling alternatives for delivering dry coal combustion residues from power plants to underground coal mines were evaluated technically and economically. The objective was to transport, handle, and inject the residues into the old workings of the mine at a minimum cost. This objective was accomplished in two steps: I) Simulation models were developed and utilized in identifying technically feasible designs in each alternative, 2) Technically feasible designs were economically evaluated to obtain the cost-per-ton of material transported. The designs that provided the minimum cost-per-ton were declared optimal An analysis was conducted for varying distances and tonnages to reveal favorable operating ranges of each alternative.

Jan 1, 1996

By William R. Yernberg

Caterpillar introduced 21 new products during Caterpillar Press Days ‘96, held in June at the company’s proving grounds near Tucson, AZ. The event, billed as the largest product introduction ever held by Caterpillar, was attended by press from around the world. Most of the new products were demonstrated at Caterpillar’s Tinaja Hills Training Center in the Sierrita Mountains south of Tucson. Under the scorching Sonora Desert sun, the press was treated to demonstrations of the new equipment. After a display of the equipment’s power and capabilities, the press was given an opportunity to operate the new models and, in some cases, compare them with the old.

Jan 1, 1996

By C. Villa Diniz

It is proposed that battery grade Mn02 can be produced directly from a manganese ore from Azul Mine in Brazil, by leaching with HCI to remove heavy metals selectively. We are working to find a way of selectively separating Cu, Ni, Co, Pb and Fe from the resulting acidic manganese chloride solution, to detoxify it and produce marketable chloride solution. Chelating ion exchange resins are proving more promising for this separation than solvent extraction with commercially available reagents. Results from batch and column ion exchange tests that characterize the behavior of copper, nickel, cobalt, lead and iron are reported.

Jan 1, 1999

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By Alexander N. Winchell

"Location. The copper mines of Michigan are all in the northern part of that state on the Keweenaw Peninsula, which extends from the (Michigan) mainland for about seventy miles northeasterly toward the middle of Lake Superior. The mines occur in a belt or zone occupying the central portion of the peninsula from end to end.. The most productive mines for many years past have been those located not far from the city of Houghton in' the central part of the zone, in a section extending about ten miles southwest of Houghton and fifteen miles northeast. The most important mines in order of location, from the northeast to south¬west, are the following: Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet. and Hecla, Osceola, Franklin, Quincy, Hancock, Isle Royale, Superior, Baltic, Trimountain, and Champion. The first three named are in Keweenaw county and all of the others are in Houghton county. Still farther to the southwest are the Lake, Mass, Adventure, Michigan, Victoria, and White Pine mines. These are in Ontonagon county.History. The exploitation of these copper mines extends back into prehistoric times. There is little evidence that the American Indians carried on mining operations in this region in the period shortly before the advent of white men, but there is abundant evidence that the ancestors of the Indians, •or some earlier inhabitants of the region, carried on primitive mining operations. For example, Mr. S. O. Knapp, Agent of the Minne¬sota Mining Company, in the winter of 1847-48, made the first discovery of prehistoric mining. This event is described as follows by Foster and Whitney :"

Jan 1, 1920

By L. Yan, B. Lambie, J. Srednicki, J. Carr

Electromagnetic emissions from electrical devices may interfere with electronic safety systems or other devices in the mining environment. This electromagnetic interference (EMI) may cause unwanted changes in the performance of the affected devices and may cause safety issues for miners. To minimize the risk of EMI, the National Institute for Occupational Safety and Health (NIOSH) has conducted research quantifying the electromagnetic emissions of several types of equipment that might be used in the mining environment. Previous research has shown that welding arcs can give off ultraviolet (UV) emissions, visible light, and infrared (IR) emissions that can cause health problem on skin and eyes. In this study, the electromagnetic emissions of the shielded metal arc welding (SMAW) process were monitored and measured. Several factors including operating mode (AC, DC positive or DC+, DC negative or DC-), current setting (low, medium, high, maximum), and electrode type were investigated to compare their effect on emission level. The test shows that the emission level from the welding process can be affected by those factors. The test data also shows that, among those factors, the operating mode has more influence on emission level than do current setting and electrode type. The information in this paper can be useful for the mining industry to better understand the emission in the 9-kHz to 500-MHz frequency range from a SMAW welder.

Feb 1, 2023

By G. M. Wali Ullah, MEHMET KIZIL, ` Micah Nehring, PETER KNIGHTS

In operations that use the sublevel stoping mining method, production scheduling takes into account factors, including ore reserve envelopes, ore grade averages, equipment capacity, feed controls to the mill, and geotechnical restrictions, across the scheduling horizon. Mathematical programming is one of the most effective methods for enhancing the decision-making process in regard to the most viable production schedule in light of a given set of limitations. The majority of research on sublevel stope mining focuses primarily on a single objective of optimisation, which is to maximise the net present value (NPV). Environmental, social, and governance (ESG) considerations are becoming more prevalent in the mining industry. This includes aspects relating to deforestation, land disturbances, gas emissions, community relations, and water usage, among many others. Institutional and other kinds of investors are becoming more interested in the work that resource companies do regarding their ESG obligations. This review article identifies the gap in the existing literature and proposes to simultaneously optimise the production schedule around three objectives. Two of these relate directly to ESG aspects.

Nov 6, 2023

By D. A. Augenstein

Operators of coal preparation plants use equipment such as large-capacity dump trucks and bulldozers to haul, spread and compact refuse material to conform to federal and state regulations governing the disposal of solid waste. For example, federal regulations require that refuse be spread and compacted in layers not more than two feet thick. If the refuse layers or piles have poor load-bearing characteristics, movement of equipment over them becomes extremely difficult. The increasing cost and limited space for the construction of settling ponds extensively used for fine refuse disposal are leading to the growing practice of dewatering the fine refuse by means of vacuum disc filters and combining the resulting filter cake with coarse refuse for waste bank disposal. However, this filter cake usually contains more than 25% moisture. Therefore, when it is combined with coarse refuse, the moisture level of the total refuse may become high enough to impair the load-bearing strength of the refuse. Precisely this problem and the attendant difficulties of moving heavy equipment arose when vacuum disc filters were installed at a preparation plant in West Virginia. Combining the moist filter cake with the coarse refuse generally results in a 12% moisture level for the total refuse at this plant. At this moisture level, the refuse can still be handled with some difficulty by the equipment. However, the problem has frequently been compouned after rains.

Jan 1, 1977

By Richard E. Beane

For several decades, the minerals industry has used leaching techniques to extract metals from rocks whose grade was too low to be treated profitably using conventional metallurgical techniques, and, as of 1972, about 15% of domestic copper production was derived using leaching methods (Beall 1). Increasing interest is currently being directed toward solution mining, particularly with respect to copper, for basically two reasons. In the first place, geological exploration has outlined several copper deposits of large tonnage and 1m', grade which are buried at sufficient depth to preclude open-pit mining which would make such mineral deposits ore deposits. Nevertheless, these occurrences provide significant potential if they could be treated by chemical leaching in situ. Secondly, the porphyry deposits of the western united States, which provide by far the largest percentage of domestic copper, do not terminate geometrically with sharp borders. These large disseminated bodies commonly decrease in grade laterally away from volumes of rock containing ore grade metallization, and the distinction between ore and waste is strictly economic. In order to extract ore grade material from the ground, a significant amount of rock containing sub-ore-grade copper must also be removed which, when placed on dumps, is amenable to solution mining. These two considerations clearly indicate the reasons for the growing interest in solution , leaching techniques--namely the ability to exploit deeply buried low grade deposits and the expansion of reserves in deposits currently under production.

Jan 1, 1977

By D. C. Martin

Stability analysis and design of open pit slopes is generally based on an assessment of rock cores and rock exposures on surface or in underground workings. Until recently, core for such assessments has been readily available from exploration drilling programs. In recent years, many exploration programs have reduced the amount of coring and rely more heavily on less expensive rotary or percussion drilling programs where drill cut-tings are sampled for geological evaluation and assay. This paper describes a technique whereby costs of the geotechnical investigation are reduced by using rotary percussion drilling information to assess geotechnical properties of the rock mass. A limited number of core holes are required to establish basic relationships between the mechanical properties of core and the characteristics of the percussion chips. These properties are used as a basis to extrapolate the coring information to encompass the entire area of the rock mass for which percussion drilling information is available.

Jan 1, 1990

By A. D. Kalogeropoulos, T. N. Michalakopoulos

This paper deals with the numerical simulation of rock cutting laboratory tests using the discrete element method. The main objective is to provide a method for calibrating numerical DEM models of rock cutting in a systematic way so that realistic results are yielded. The numerical models are developed with the discrete element code Yade, which models rocks as a collection of bonded spheres. The models are calibrated in a four-step process based on the design of experiments method and optimization. The calibrated models are evaluated both quantitatively and qualitatively against actual laboratory cutting tests, in terms of the ratio of the simulated mean cutting force to the actual one and the cutting force time series, respectively. The fully calibrated models showed that the simulated cutting process matched qualitatively the actual cutting force recordings and underestimated the mean cutting force by approximately 3%. It is concluded that well-calibrated numerical simulations of the rock cutting process can provide not only a better understanding of the process itself but also quantitative data regarding the cutting force and energy requirements.

Dec 28, 2022

By Andrea Brickey, RICHARD AMOAKO, Akshay Chowdu

Production forecasts derived from the medium-term schedule represent the best path forward for underground mining operations to achieve corporate and operational goals. Unforeseen circumstances, such as equipment breakdown, can cause significant deviations from established production forecasts in the short term. Such situations require timely mitigation of the effects of the deviations in order to stay as close as possible to the medium-term plan. This paper presents a deterministic mathematical formulation for short-term scheduling that addresses this challenge. The formulation is able to make up for deficits resulting from operational disruptions by minimizing deviations from medium-term production goals and mediumterm activity start dates. We demonstrate this in a case study by simulating disruptions involving reduction in ore extraction capacity and development advance rate. Aside from the rescheduling capability, this formulation can help mine planners conduct analysis on the impact of various disruptions on the schedule. The formulation can help identify those conditions or disruptions that are more detrimental to the achievement of forecast targets, or otherwise. The formulation also affords mine planners the flexibility to prioritize one production goal over the other, depending on operational conditions at the mine. In the future, we seek to incorporate in the formulation respirable dust, diesel particulate matter, and ventilation constraints in order to create more realistic schedules and enhance miners’ health and safety.

Sep 6, 2023

By Zhibiao Guo, Jinglin You, Dongshan Yang, Yuanxin Zhao, Yuhui Li, Jingwei Gao

By utilizing collapsed gangue to create gob ribs, roof cutting and roadway maintenance (RCRM) technology enables coal pillar-free mining, presenting a novel approach. Due to their inherent structure, faults, which are common geological formations, can lead to various hazards, including fault sliding and significant deformation of roadways. In this study, a selfdesigned underground engineering simulation test device is utilized to imitate the cross-fault mining of the 11,101 working face in the Qipanjing Coal Mine (East). The objective is to examine the behavior of the surrounding rock and stress evolution. Generally, the experimental findings demonstrate that compared to the return air roadway, the RCRM roadway experiences a 3.3% decrease in maximum coal rib stress. This suggests that the implementation of this technique can effectively alleviate the stress on the surrounding rock of the roadway. The maximum coal rib stress, lateral pressure of the gob rib, and maximum deformation of the roof near the fault of the RCRM roadway are 11.3%, 25.6%, and 86.1% greater than those of the conventional geological conditions, respectively. The roadway deformation is negatively impacted by the fault structure. Based on experimental data and field measurements, a discrepancy in the maximum roof deformation between the test and field monitoring results under typical geological conditions is 8%. This indicates a favorable alignment between the test results and the real-life scenario. In conclusion, the proposed targeted control technique is implemented in the field by integrating the mining invariant equation and gangue volume expansion equation. This not only validates the effectiveness of the technology but also offers valuable insights for the future utilization of RCRM technology under comparable circumstances.

Feb 20, 2024

By Sean Masse

New Gold?s New Afton Mine, located 8 km (5 miles) west of Kamloops, British Columbia, is a 4.5-Mt/a (5-million stpy) block cave mine, making it the highest tonnage underground hard rock mine in Canada. The reserve is estimated at 52.5 Mt (55.9 million st) with grades of 0.65 g/t (0.02 oz/st) gold and 0.93 percent copper (2012). Commercial production was achieved in July 2012 and nameplate production was achieved ahead of schedule in September 2012, with the cave breaching to surface in 2013. The mill has a SAG and a ball mill with a froth flotation circuit.

Jan 1, 2014

By C. S. Simons

The aphorism that provided the title of this paper is probably a couple of hundred years old, but it still expresses a fundamental truth in the metals industry. This truth will be illustrated through a brief review of the major developments in the extractive metallurgy of the oxidized ores of nickel - the "laterite" ores. While the details to be discussed are for the most part specific to nickel, a close parallel with other commodities - particularly in recent years - will be apparent even to those whose interest in nickel itself is slight. Thus it is hoped that this paper will be stimulating, at the least, to anyone who is concerned with the implementation of process improvement, "Invention" in the present context means any change from "conventional" process technology that shows a reasonable chance of reducing costs, increasing revenues, or both, in the production of a commodity. This can be anything from a simple rearrangement of flowsheet steps to a completely different basis for processing. And the result may reduce costs by more efficient use of energy or labor or reagents; may increase revenues by better recovery of the primary product or by introducing the recovery of previously ignored by-products; may insure sales volume (and thereby cash flow) through higher product purity or an improved product form. "Necessity" is the perceived need to attain at least one of these classes of results. This perception of necessity, however, varies widely from management to management and from project to project.

Jan 1, 1983

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

By C. Brown, N. Rayyan, T. H. Dubaniewicz

Lithium-Ion batteries (LIBs) have the potential to go into thermal runaway which introduces a new ignition source in hazardous environments such as gassy underground mines that may contain methane in the surrounding air. Researchers from the National Institute for Occupational Safety and Health (NIOSH) used an accelerating rate calorimeter (ARC) to induce thermal runaway in individual lithium-titanium-oxide (LTO) and lithium-nickel-cobalt-aluminum-oxide (NCA) LIB cells within a sealed enclosure with either no methane, a lean, a stoichiometric, or a rich methane-air mixture in the surrounding canister to determine if these LIB types would ignite the methane, causing an additive effect on overpressures. Canister pressures and maximum temperatures reached by the cells, surrounding air, and exhausted gases were measured in this study and remained consistent with varying methane concentrations.

Feb 1, 2023

By S. Uihteenmaki

Pyhasalmi is a massive sulfide orebody located in central Finland. The mine has been in operation since 1962. The flotation concentrator produces Cu, Zn, Pb and pyrite concentrates. The plant has used an on-stream analyzer for process control since 1968. The original analyzer has overlived a few generations of minicomputers, but the analytical parts are essentially unchanged. The on-stream analyzer is a critical component in plant process control system, which has made Pyhasaltni one of the pioneers in the art of computer control and optimization of flotation plants. The paper summarizes the experiences gained from the use of the high performance elemental analyzer system and the proven benefits from the use of on-stream analyzers at a complex sulfide flotation. The aging analyzer is approaching the end of its useful life. A new state of the art analyzer system is undergoing testing at Pyhasalmi.

Jan 1, 1999

By Charles A. Hickey

The dining industry game tome Spruce Pine area a few years after tine Civil War. Two Yankees came down from Massachusetts to mine sheet mica to sell to the stove manufacturers for windows in heating stoves. At this time the method of mining was very crude; it was done only with pick and shovel. They were mining mica from the soft veins. Later they progressed to hand grilling and blasting. Hand drilling was quite an art in the area. One man would hold and turn the steel while one or two other men would drive the steel with hammers. In shaft raining, the muck and water was removed by hand winches called windlasses. About 1920 air compressors and jack hammers came into use. These were perhaps tide greatest improvement that has ever come to the area's mining industry. Later carne gasoline hoists, air drive water pumps, and all electrical equipment. Mica mining has, for the past few years, been very modern and efficient.

Jan 1, 1962