Search Documents

By J. H. van Laar, C. S. L. Schutte, M. Le Roux

Highly energy-intensive systems prone to wastage are significant causes of unnecessary energy losses in industry. Deep-level mine chilled water reticulation systems fall within this category of inefficient energy-intensive systems. Some techniques (measured baselining, zero-waste baselining, leak detection, and control valves) exist to identify and reduce wastage in mine water reticulation systems. However, these techniques have not been compared, which begs the question of which is more accurate. A need, therefore, exists to compare these methods to determine the effectiveness of each. This study investigates each method and applies them to a case study mine, providing a platform for comparison. These methods identified wastage ranging between 2 and 20 l/s (3–30% of water consumption). The comparative effectiveness of the methods from best to worst was found to be zero-waste baselining, leak detection, control valves, then measure baselining. This study proposes an application procedure combining the considered methods to identify and eliminate wastage on deep-level mine systems more efficiently.

Jan 31, 2024

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019

By Wilson W. Zoogah, Joel G. Burken, Abdullah Al Moinee, Mariam K. Al-Lami, Kwame Awuah-Offei

Soil CO2 flux serves a critical indicator of ecosystem function and carbon cycling in disturbed landscapes. This study measured and quantified temporal patterns and environmental drivers of soil respiration across fifteen revegetated treatment plots over a 12-week period (July-October 2025). Utilizing automated CO2 flux measurements, we investigated differences between treatments and quantified their relationships with soil temperature, moisture, and atmospheric pressure. One-way ANOVA revealed significant treatment effects on CO2 flux (F4, 442 =14.1, p < 0.001, η2=0.113), with amended plots exhibiting 40–50% higher mean fluxes than control plots. Weekly temporal analysis demonstrated distinct temporal patterns, with peak fluxes registering in mid-August before a gradual decline. Multiple regression analyses showed that soil temperature (β=0.043, p < 0.001) and moisture (β=2.31, p < 0.001) are the primary flux drivers, together accounting for 18.2% of total variability (adjusted R2=0.182). Atmospheric pressure had a moderate effect (β=1.13, p < 0.001), detectable only in multivariable analysis. Variance partitioning indicated that environmental factors explained more variability (18.7%) than treatment effect (10.5%), with approximately 71% of flux variability attributed to finer spatial or temporal variability. These results demonstrate that revegetation amendments enhance soil biological activity and impact geochemical cycling, and that temperature and moisture are dominant controls on respiration dynamics in reclaimed mine soils. The findings provide quantifiable benchmarks for ecosystem recovery through altering soil biology and geochemistry and for quantifying carbon sequestration potential in post-mining landscapes.

Feb 22, 2026

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step-function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step-function approach. An important issue is how these three versions compare to each other in terms of simulated capacity requirements for belt conveyors. Another is-sue is how they compare to peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1997

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

In this study, a parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading, generated from seam dip, on the strength and the failure propagation pattern of a stone pillar using two simplified geometry types. In type 1, the sidewalls of the pillars were assumed to be perpendicular to the roof and the floor, while in type 2, the sidewalls of pillars were assumed to be vertical. The complex pillar geometry in dipping mines was frequently modeled using these two geometries. To capture a complete picture of the effect of seam dip on pillar stability, the modeled width-to-height (W/H) ratio of the pillars, in situ stress field, and pillars roof/floor interfaces were systematically varied to account for the potential distribution of values for these parameters across the underground stone mines in USA. Results from the numerical modeling indicate that dipping pillars have reduced strength compared with horizontal pillars. Also, an asymmetric failure propagation pattern could be obtained depending on an interaction between the W/H ratio, seam dip, in situ stresses, and pillar geometry.

Feb 5, 2021

By Hemendra N. Kalia

Several attempts have been made in the past sixty or so years to commerciliaze the vast oil shale deposits of the United States of America. However, the industry has yet to become viable and economic. To date, it has not been possible to produce oil from the oil shales at a competitive price when compared to the oil produced from oilfields by conventional methods. However, the development work has been quite fruitful in furthering the art of thick bed mining and technology of in situ retorting. The in situ method has the potential of recovering oil from thick beds and the resource recovery potential is much greater than that from underground mining and surface retorting. In situ methods require that the shales/ marlstones be fragmented &apos; in place to induce adequate porosity and permeability to allow in situ&apos; heating of the fragmented shales. This can be accomplished by using explosives. However, it has been found that the existing blasting systems, though very efficient, are somewhat lacking. The explosive become insensitive when shot in multiple vertical decks. They can also become insensitive when spaced horizontally at close proximity to other charges. Also, since the blasting is done in a very limited free face, this limits the delay time that can be allowed between charges. Consequently it is not always possible to predict the performance of the blasting system on a routine basis. Furthermore, since it is not possible to undertake secodary blasting, it is imperative that the blast design function properly. Recent, successful retorting by Occidental Petroleum Company of retorts seven and eight suggests that some of these problems may have been overcome. This paper addresses some aspects of in situ retorting and problems those have impeded the development of a viable oil shale industry in the U.S.A.

Jan 1, 1983

By Scott Rosenthal, Dave Gilkey, Theresa Stack, Daniel Autenrieth, Ciara Kremer

Jackleg drill operators are exposed to harmful levels of hand-arm vibration (HAV). Anti-vibration handles and gloves provide modest reductions in HAV exposures and forearm muscle exertion from the use of anti-vibration handles and gloves by jackleg drill operators. The goal of this pilot study was to investigate changes in HAV with the use of anti-vibration gloves and handles compared to forearm muscle exertion experienced by operators and measured with surface electromyography (EMG). Five subjects operated the drill under four different cases: no anti-vibration controls, anti-vibration gloves only, anti-vibration handle only, and simultaneous anti-vibration handle and glove use. Muscle exertion was expressed as a percent of maximum voluntary contraction (%MVC) and was compared using Welch’s ANOVA with Games-Howell post hoc comparisons. The case with both anti-vibration controls in use simultaneously (largest grip diameter) was associated with a mean %MVC of 36.13% during operation for all forearm muscles combined, which was significantly higher than that of the other cases (p < 0.05). There were no statistically significant differences in mean HAV exposures. The anti-vibration handle with anti-vibration glove case only increased the maximum allowable exposure time by 8 min as compared to the control case without any anti-vibration controls. These results suggest that the modest HAV exposure reductions from the use of anti-vibration handles and gloves may pale in comparison to the increased muscle exertion resulting from their use, and this trade-off among jackleg drill operators is a potential concern that warrants further investigation.

Jul 12, 2021

By Jamal Rostami, Mark Board, Clayr Alexander, Muthu Vinayak Thyagarajan

In the past several decades, many major equipment manufacturers have ventured into developing new technology for underground hard rock excavation. This includes variety of configurations for full and partial face mobile excavation units. Mining industry prefers machines that can excavate noncircular, flat invert profiles and be able to make tight turns in hard rock. The need to use disc cutters for cutting hard rock has impeded the development of such machines due to the need for gripper system or large mass of a machine to support the force requirements of the disc cutters. Most of the prior attempts have been partially successful and the operations have faced some practical limits and challenges. Among the units that have been successfully used, one can name mobile miner, which was used for rock excavation in some projects. A redesigned mobile miner, called the “Remote Vein Miner,” or RVM, has been developed by Epiroc for underground hard rock mining in Hecla’s Lucky Friday Mine. This equipment potentially opens numerous opportunities for innovation in civil tunneling projects, where the operational flexibility and accessibility of a TBM’s limited tunnel path, design of the profile, and cost are limiting factors. This paper explores the application of the RVM in tunneling projects, its advantages and possible areas of innovation in tunnel planning and design.

Jun 13, 2021

By C. R. McKee

In-situ mining of hard rock deposits will only become successful as we understand the engineering parameters involved and the design limitations they impose. As recognized by Wadsworth1 the most critical area is the enhancement of permeability in a hard rock mass. Along with creating permeability, the appropriate flow and fragment size conditions must be generated to insure economic rates of mineral recovery. In this article our interest is confined to true in-situ processes in which boreholes are drilled from the ground surface or a mine drift to deeper strata. We assume that fractures and permeability enhancement will be due to explosives detonated in boreholes. Other techniques such as hydraulic fracturing do not produce the necessary size distribution to promote economic extract ion rates unless the medium is already highly fractured and interconnected. Notable exceptions where hydraulic fracturing is applicable are many oil, gas and salt deposits. For many in-situ processes, an array of explosive charges offers the opportunity of creating a distribution of many fractures not achievable by other techniques. Such a situation would be suitable, for example, to in-situ mine hard rock gold, uranium, copper or oil shale deposits and may enhance oil and gas recovery in certain situations. The purpose of our article is to review and extend the explosive permeability theory of McKee and Hanson 3,4,5 and to apply its results to derive design parameters suitable for in-situ mining.

Jan 1, 1981

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Cat 994 class) as primary loading equipment in open pit iron ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Data were gathered on loader selection rationale; operating and maintenance experience; and production, availability, and cost information. Brief time studies were conducted to indicate machine performance and utilization. The paper summarizes the field data and includes economic comparisons of wheel loaders versus cable shovels in an iron ore application.

Jan 1, 1996

By Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jennica L. Bellanca

Accidents involving powered haulage and mobile equipment such as haul trucks often account for the greatest number of fatalities in the mining industry each year. Despite previous analyses that have identified root causes and other contributing factors, there is still a need to better understand the events leading up to these types of accidents, what lessons may be learned, and what strategies can be employed to prevent fatal accidents from occurring. This study examines Naturalistic Decision Making (NDM) using the critical decision method (CDM). The CDM is a retrospective interview approach used to explore timelimited, high-stakes, decision-making. In this study the CDM is used to obtain more information about what happens prior to, during, and after a potentially fatal situation such as a near-miss event, loss of control, or minor accident involving equipment damage. Researchers captured firsthand accounts from 21 haul truck operators involved in near-miss events from mine sites of various sizes and commodities throughout the United States. These accounts provide rich and detailed narratives from the perspective of haul truck operators themselves and reveal insights into what decisions haul truck operators make, what sensory cues they perceive, and what strategies they employ during challenging and non-routine situations. Decision-related themes that emerged from the data are presented and discussed. These results, along with potential solutions offered by study participants, can help to inform future research, raise awareness about hidden hazards, and build more creative interventions and realistic training scenarios for use by the industry to address haul truck safety issues.

Feb 1, 2024

By H. H. Hayden

The accident repeater-40 you have one at your mine? Unless your company is vastly different from most coal companies, you will find that a small percentage (11-12%) of your employees will have a large percentage (47-50%) of your accidents. When you find out that this is a fact, what do you do? First, you establish a set of guidelines that can be used in identifying the ?accident repeater?. Next, you determine the type of action necessary to improve work habits and safety performance of the accident repeater. With these two steps in mind, objectives are developed for an ?accident repeater? program.

Jan 1, 1984

By Milos Krofta, Donald B. Aulenbach, James P. Van Dyke

INTRODUCTION An innovative Ø.1-MGD (378.5-m3/day) biological and phyicochemical wastewater treatment system at Hancock, Massachusetts, USA, has been treating the domestic sewage generated from the four-season Jiminy Peak timeshare resort since 1985. The influent raw sewage is collected and equalized in an equalization tank, then biologically treated by two rotating biological contactors (RBC). A portion of the RBC effluent is discharged to a secondary sedimentation tank to simulate conventional waste treatment by a conventional RBC system. For parallel treatment the remaining portion of the RBC effluent is discharged to an innovative Sandfloat (SASF-8) clarifier to simulate a two-stage biological and physicochemical treatment by RBC-Sandfloat. Both secondary sedimentation effluent and Saandfloat effluent are later combined together and discharged to a tertiary sand filter and two UV disinfection&apos;units for final polishing. The operation and performance data of Jiminy Peak plant in the period of May 1985 to March 1988 was fully documented in the Lenox Institute technical report No. LIR/Ø3-88/292 (391 pages, March 1988). This report presents only background information and complete plant data in the period of April 1988 to January 1989. Dr. Lawrence K. Wang and Mr. James P. Van Dyke have been the Consulting Engineer and Director of Special Projects, respectively, for the Jiminy Peak Project since 1985. (Key Words) Innovative and Alternative Technology, Rotating Biological Contactor, Sandfloat, Dissolved Air Flotation, Sedimentation, Tertiary Filtration, Ultraviolet, Disinfection. BACKGROUND INFORMATION Jimmy Peak, Inc., Hancock, Massachusetts, has designed and constructed a secondary wastewater treatment system consisting of preliminary/primary treatment facilities, two rotating biological contactors, a dissolved air flotation clarifier, a secondary sedimentation clarifier, a sand filter and two ultraviolet (UV) disinfection units. Total average wastewater flow is approximately Ø.1 ) (378.5 cubic meters per day). In accordance with the Consulting Engineer&apos;s preliminary design, the total wastewater stream is initially collected and equalized by an equalization tank, and then biologically treated by rotating biological contactors (RBC). Part of the RBC effluent is diverted to a Krofta Sandfloat (SASF-8) for physicochemical clarification in order to simulate an innovative RBC-Sandfloat two-stage waste treatment system. The remaining part of the RBC effluent is diverted to a sedimentation tank for secondary clarification in order to siumulate a conventional secondary RBC-sedimentation waste treatment system for the purpose of parallel comparison. Both Sandfloat effluent and sedimentation effluent are later combined together and discharged to the subsequent sand filter and UV disinfection unit for final polishing. Figure 1 shows the flow diagram of Jiminy Peak Plant. The Massachusetts Clean Waters Act (M.G.L.c.2l,s.26-53) was amended by Chapter 246 of the Acts of 1973 to authorize the Massachusetts Department of Environmental Quality Engineering (DEQE), Division of water Pollution Control, Boston, Massachusetts, to regulate discharges into all waters of the Commonwealth of Massachusetts, including groundwaters. The DEQE regulates discharges through the issuance of discharge permits which impose limitations on the amount of pollutants which may be discharged in the effluent, together with monitoring and reporting requirements and other conditions to insure adequate treatment of all liquid wastes prior to discharge. The DEQE reviewed the application submitted on behalf of Jiminy Peak, Inc. for a permit to discharge sanitary wastes from the Jiminy Peak secondary wastewater treatment system located off Brodie Mountain Road, Hancock, Massachusetts, and subsequently developed the conditions contained in the Groundwater Discharge Permit No. Ø-188. More specifically, Jiminy Peak, Inc. (i.e. the permittee) has been authorized to discharge into the ground from the Jimmy Peak secondary wastewater treatment facilities for which the Permit No. Ø-188 was issued, a treated effluent

Jan 1, 1989

By F. Alsobrook

Coleman Quartz Inc. has a long history as the sole U.S. producer of lascas for the cultured quartz growing industry based on its unique deposits in Arkansas. Since 1989 the company has also been producing metallurgical grade silica for the ferrosilicon industry from a deposit of unusually pure Arkansas novaculite. This paper chronicles Coleman&apos;s trans-formation of an abandoned railroad ballast quarry into a generator of $1.5 million in annual sales to a nontraditional novaculite market. Potential additional applications for this high quality silica rock will also be mentioned.

Jan 1, 1992

By J. Kretschmann, H. Mischo, O. Drusche, S. Krause

Mining is and will be inevitable in spite of the increasing implementation of circular strategies. The energy transition and population growth will boost the demand for critical raw materials. It is the opportunity for miners to reinvent their business models. Generating attractive new business cases with sustainability-oriented innovations meets investor and stakeholder expectations from the beginning. This contribution guides managers on their pathway towards sustainable success. Contextual sustainable business model patterns will be presented that can be adjusted individually, regardless of actor’s size. It will also point out, how sustainable value creation can be measured on business model level.

Feb 1, 2023

By Muhammad I. Kabir

The streamline method of recovery prediction reduces a two-dimensional problem to a bundle of one-dimensional ones. This paper presents the development and application of a novel scaling technique which, when used with a streamline model, causes s bundle of one-dimensional problems to further reduce to a single one-dimensional calculation. The one-dimensional calculation accounts for chemical-rock interactions and the streamline model for areal sweep. The scaling technique significantly reduces computation time, is readily modified to desk-top calculations, and can be applied to both absorbing and reacting species. The work was sponsored by the Interior Department&apos;s Bureau of Mines.

Jan 1, 1984

By Kendall Y. Onstott

The paper presents the results of a plant test using WEMCO 1 + 1 enclosed flotation machines for inert gas (nitrogen) flotation of by-product molybdenite from copper sulfide concentrate. Copper depressant consumption in the rougher flotation stage was reduced by 68% as reagent consuming oxygen was removed from the flotation air. Unlike other nitrogen flotation systems used in the industry, nitrogen is recovered above the flotation cells and from froth in tails and concentrate streams and recycled, resulting in minimal nitrogen makeup requirement.

Jan 1, 1984

By Laszlo Valentyik

The wide scale acceptance of the heavy media separation is due to its simplicity and efficiency. The two most important variables of the process are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media solids. The almost always present clay in the feed and conse¬quently in the medium acts as a stabilizing agent, and its optimum concentration varied between 3-4%.(1,2) Since polymers essentially perform the same function in oil well drilling muds - i.e. to suspend cuttings during drilling - as the fine clay in heavy media separation, this led to the investigation of whether polymers could be used in heavy media separation as supporting agents. During the first phase of the work, it was found that by the controlled addition of polymers, the stability of the heavy media increased without unduly increasing viscosity of the suspensions, thus yielding conditions for more effective and efficient separation. The results of the experiments were reported in a paper at the AIME Centennial Annual Meeting, March 1971.(3) This paper presents the results of the experiment carried out during the second phase of the work.

Jan 1, 1975

By W. A. Wilkinson

Mine planners are under pressure to evaluate the impact of changing economic times and newly acquired data on their mine plans. Incorporating changes such as commodity prices, customer sales, fluctuating cost assumptions and newly acquired geologic data requires quick turnaround for model building and planning to keep mine plans on pace with changes as they occur. Because of the length of time required to perform some of the geologic modeling and mine planning tasks, planning frequency may not be keeping pace with the frequency of change. To meet these challenges, one leading North American mining company successfully increased the frequency rate and accuracy of its mine plans to stay current with incoming data, ensuring its mine plans reflect the latest information, thereby minimizing or eliminating production cost variance.

Jan 1, 2010

By J. T. Tanner

The research activities of the Minerals Research Laboratory, which is a part of North Carolina State University, is normally confined to solving beneficiation problems, and developing flotation processes for the mining industry. In recent years the laboratory has veered from its main purpose somewhat and has placed some emphasis on the manufacture of products from mineral concentrates. This has been the result of requests for help from industry. One such request came to the MRL from a talc producer in North Carolina who was having a difficult time competing with foreign imports of steel marking crayons. He felt that if a process could be developed whereby a satisfactory crayon could be produced from powdered talc at a low cost that he could compete.

Jan 1, 1986