Search Documents

By R. K. Singhal

This new tool can be used for the proper assessment of the potential economic wealth of any risky capital project. It does provide an unambiguous recommendation of the type "go or no go" to the decision-maker simply by comparing two different ratios profit/investment. One ratio determines the minimum value required to at least break-even while the other measures a probable value based on the asymptotic theory of statistical extremes (weakest link concept). Its application is briefly illustrated by means of an underground gold mine project, an oil sands mine project and a poly-metallic open pit project.

Jan 1, 1993

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification (nickel, cobalt, copper, and manganese) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte, ammoniacal leaching (gas reduction or Cuprion), and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stems from the 1970s and 1980s and is not always easily accessible. This paper will detail the series of tests conducted and provide updated results obtained (high Ni/Co/Cu recovery with limited Mn/Fe), as well as comment on the potential treatment options on the product solution and residue.

Feb 1, 2025

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By D. J. Fitzpatrick

The paper reviews current mining subsidence research at The Department of Mining Engineering, University of Notting- ham. Special attention is being devoted to prediction of ground movements between the mining horizon and the surface using physical and computer-based models. The paper presented discusses linear and non- linear finite element methods and compares results with those from physical models and field observations. Special attention is focussed on the determination of the effect of caved zones on overlying and underlying geological structures. The paper presents data from comparisons with U.K. case histories.

Jan 1, 1986

By Xiaoyan Luo, Congcong Dai, Gaipin Cai, Xin Liu, Lu Zong

To overcome the difficulty of accurately judging the load state of a wet ball mill during the grinding process, a method of mill load identification based on the singular value entropy of the modified ensemble empirical mode decomposition (MEEMD) and a probabilistic neural network (PNN) classifier is proposed. First, the MEEMD algorithm is used to decompose the vibration signals recorded under different load states to obtain the intrinsic mode components, and a correlation coefficient threshold is used to select the sensitive mode components that characterize the state of the original signal. Second, singular value decomposition is used to obtain the singular value entropy. Finally, the load state of the wet ball mill is judged based on the magnitude of the singular value entropy. A characteristic mill load vector is constructed from the singular value entropies of the cylinder vibration signals recorded under different load conditions and is used as the input to a PNN, which then outputs the predicted ball mill load state; in this way, a load state identification model is established. Grinding experiments are presented to verify the effectiveness of the proposed method, showing that the method can accurately identify the load state of a wet ball mill. ()

By A. D. Randolph

Comminution represents one of the major costs of mineral recovery from low-grade ores. Efficient mineral recovery in a typical low-grade ore grinding-flo¬tation process depends on grinding the ore small enough to liberate mineralization without producing excessive slimes, which would result in higher power and flotation reagent costs. Size criteria for efficient grinding should be stated in terms of the distribution of mineralization sizes, but as the mineralization-size distribution is difficult to determine, less desirable criteria of absolute particle-size distribution (PSD) are used in practice. Thus, there is considerable incentive to be able to analyze and predict the PSD performance of grinding circuits for control and optimization of the process. Any realistic model of a grinding circuit must account for recycle of oversize material; such oversize recycle adds to the total mill load and limits total production rate. Simulation of such closed-circuit operation to study grind factors affecting total throughput can be done in a straightforward fashion provided recycle calculations can be added to an accurate input-output model of PSD in the grinding mill itself. Such a total simulation of mill performance is of obvious practical value in assessing the practicality and benefits of various over-all mill control schemes and/or modes of operation. For example, considerable interest has been shown in the development of continuous on-line particle-size sensors and such instruments should be an operating reality in a few years. A total closed-circuit PSD model of this type would be invaluable in the utilization of, and in predicting the pay-out from, such an on-line particle-size sensor. The purpose of this paper is to present a new approach to the development of an input-output PSD model of a grinding mill. The model is continuous in the par¬ticle size coordinate, L, and is based on the principle of a particle population balance along the particle size coordinate. Most previous studies of the grinding unit operation attempt to relate power

Jan 1, 1971

By Gregory Rumbaugh, Christopher Mark

Recent pillar collapses have caused five large airblasts in underground U.S. limestone mines. One of these events injured three miners, but all of them put many other miners at risk. To better understand the hazards, Mine Safety and Health Administration (MSHA) conducted a comprehensive review of the international literature on airblasts. More than 40 airblast cases have been documented, in a wide variety of minerals. Experience shows that miners that are in the direct path of the air as it moves towards the mine exits are at the greatest risk. The paper describes a risk management methodology that can be used to evaluate the level of hazard throughout the mine and aid in the selection of controls to reduce the risk. The paper concludes with a detailed case history of an actual pillar collapse and airblast.

The General Purpose Simulation System (GPSS) is a computer simulation language that has been used for simulations of open pit haulage operations since the 60's. It is easy to learn, simple to use, and has a block-diagram structure that is amenable to load-haul systems. However, due to its lack of flexibility, there are situations where another language should be chosen. This paper reviews the characteristics and capabilities of both GPSS and FORTFAN with regard to open pit shovel and truck simulation. The relative advantages and disadvantages are highlighted and a case study presented along with comparative results from two computer models (one written in GPSS and the other written in FORTRAN).

Jan 1, 1986

By Meng Li, Hao Nie, Weitian Ding, Mamdouh Omran, Ying Li, Yao Ge, Yaowei Yu, Abourehab Hammam, Lei Zan

This study examines the isothermal and non-isothermal reduction behaviors of iron ore compacts in a pure hydrogen atmosphere and compares the results obtained during the reduction process by CO. The different phases accompanying the reduction reactions were identified using X-ray diffraction (XRD) and its morphology was microscopically examined. In isothermal experiments, temperature plays a significant role in the reduction process. At any given temperature, the reduction rate during the initial stages is higher than that during the final stages. The reduction rate in H2 atmosphere was faster than in CO gas. The comparison of activation energy values suggested that reduction with H2 is more efficient thanwith CO. At the same temperature, the time required to achieve a certain degree of reduction was lower when using H2 gas than CO atmosphere. In non-isothermal tests, the heating rate has a significant effect on the reduction rate and reduction extent. At the same heating rate, the degree of reduction was higher in H2 atmosphere than in CO gas. Based on experimental data, the parameters of reaction kinetics were deduced by application of model-free and model-fitting methods. The reduction in H2 atmosphere was controlled by nucleation model (Avrami-Erofeev model), while the CO reduction reaction was controlled by gas diffusion.

Sep 29, 2020

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

By J. F. Brune

This is a shortened version of the paper ?The Methane-Air Explosion Hazard Within Coal Mine Gobs published in the 2013 volume of SME Transactions (Brune, 2013). This paper analyzes the explosion hazard resulting from the formation of methane-air mixtures in the mined-out gobs of underground longwall coal mines. Evidence from numerous mine explosions suggests that explosive methane zones can form within longwall gobs. Explosions and fires resulting from these methane accumulations have led to severe and fatal injuries to the miners, including the explosion of the Upper Big Branch mine in West Virginia, where 29 miners lost their lives. The paper also reviews current research on numerical modeling of gas flows in longwall gobs and outlines how targeted injection of nitrogen into gobs can effectively reduce the volume of such explosive methane zones. The paper concludes that comprehensive monitoring of gas compositions along the accessible fringes of the gobs along with inertization, improved ventilation schemes and further research are necessary to control this explosion hazard and make mining operations safe.

Feb 23, 2014

By S. M. Bulatovic

The western industrial world has to rely more and more on complex polymetallic sulphide ores as sources for base metals. These ores are composed of fine grained sulphide minerals such as chalcopyrite, galena, sphalerite, pyrite, pyrrhotite and marcasite. The liberation sizes of the individual minerals can range between 30 um and 5 um. Therefore, applying conventional techniques to recover these finely disseminated minerals usually results in unsatisfactory metallurgical performances with high losses of the valuable mineral to the slime , fraction of the tailing. New concepts for treating these polymetallic complex ores are discussed in this paper. Beneficiation techniques utilizing new reagents and a new approach to pulp preparation are described. Some of these techniques were applied to ores from existing concentrators as well as to new ores. The results of these studies are discussed in the following sections.

Jan 1, 1990

By C. Clark, J. Seymour, D. Benton

"National Institute for Occupational Safety and Health NIOSH is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics, and alternatives, based on information from injury reports, legacy research, stakeholder input, and published literature. Jackleg drills are involved in more ground fall accidents in underground metal mines than any other drill. Jackleg-related injuries are most prevalent at the face in the course of installing initial ground support. Alternatives to jacklegs for drilling and bolting under incomplete support in narrow underground openings are not yet available. Small mechanized bolting equipment needs to be developed to address jackleg-related accidents and improve safety at mines where jacklegs are being used. JACKLEG DRILL Description The term “jackleg drill” is a generic name for a class of handheld, rotary, percussion rock drills that are equipped with an attached reaction leg to provide stability and thrust for the drill (Figure 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jacklegs are classified according to the bore size of their pneumatic pistons which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in) [Kurt, 1982; Clark, 2012]. Jacklegs typically weigh 460 N (103 lbs), but their weight can approach 535 N (120 lbs) after they are fitted for operation with drill steel and air and water hoses [McKibbin and Clark, 2001]. In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in) diameter holes 1.83 m (6 ft) deep in rock. Application The jackleg drill is primarily used in underground mines when the size of the ore body, the ground conditions, or the mining method do not permit large openings to be mined using mechanized equipment (e.g., narrow vein mining). Jacklegs are used to drill blast-holes for explosives and also holes for installing ground support. These versatile drills are used in nearly all phases of mining including exploration, development, production, and maintenance [Kurt, 1982; Williams et al., 2007; Chen and McKinnon, 2012]. The jackleg is used to drill holes in rock using drill bits attached to hollow steel bars called drill steels (rotary percussion drilling). After the hole is drilled, the jackleg can be used to install different types of ground support components, depending on the ground conditions and the specific ground support measures that are needed. For example, the jackleg can be used to install expansion-anchor rockbolts or resin-grouted rockbolts using the drill’s rotary-motion feature. On the other hand, the jackleg can also be used to install friction-type Split-Set™ rockbolts using the drill’s percussion (hammer-motion) feature. As shown in Figure 1, various washer-like bearing plates can be installed along with these bolts to provide additional ground support and to help secure surface control products, such as wire mesh and shotcrete that are in turn used to retain small, loose material between the bolts [Clark, 2012]."

Jan 1, 2016

By C. G. Anderson

Extraction of valuable resources from complex orebodies will become more common. This is obvious for two reasons. First, the cleaner and more readily processed ores have continually been depleted through centuries of mining. Second, new technologies have evolved for effectively handling complex ores. One of these new processes has been in place at Sunshine since 1984. Based on sulfuric acid oxygen pressure leaching with nitric acid as an oxidizer, this patented technology allows silver and copper to be efficiently recovered from a complex sulfide concentrate. As efficient as it is, this process represents novel technology found nowhere else on an industrial scale. As such, a research program was undertaken in 1989 to optimize this leach process and to better understand it. From this study, several potential plant improvements were found and recommended. As a result, two of these options, nitric acid replacement by sodium nitrite and concentrate regrind are now used in day to day operation at Sunshine. Patenting of these changes was recently accomplished (1). Thus, the development, perceived mechanisms, plant integration and potential applicability of this technology will be covered in this paper.

Jan 1, 1994

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023

By Jianbo Hu, Tao Zheng, Zhao Qihua, Rui Su

Rock mass discontinuities play a significant role in evaluating the stability of rock slopes. It is necessary to collect and analyze these discontinuities to fully understand the mechanical and deformational behaviors of rock masses. Based on the digital images of some slope faces, this paper proposes a framework based on machine learning for detecting and extracting discontinuities. First, digital images and photo poses are combined, the original scene is reconstructed, and 3D point cloud data are obtained. All captured point clouds can be mapped with each image by the direct linear transformation algorithm. Next, the detection machine learning algorithm is used to segment rock mass discontinuities on 2D digital images. Finally, based on the mapping relationship, the 2D digital images that were segmented are transformed into 3D point cloud data. The geometric parameters of the corresponding discontinuities can be extracted by the DBSCAN and the Skmeans algorithm and the characterization of specific rules. The proposed framework was evaluated utilizing a quantity of slope digital images in the Yebatan hydropower under construction, located in Sichuan Province, China, as a case study. The results illustrate that most deviations are less than 10° for the dip direction and dip angle, which verifies the reliability of the proposed framework and maintains acceptable measurement accuracy.

Nov 6, 2022

By R. J. Sheets

In 2009, the Gold Quarry openpit mine experienced multiple large-scale slope failures of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope failures occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower, high plasticity subunits of the Carlin Formation. This deformation created preferential flow paths that allowed ground water from the upper sandy subunits to infiltrate low-permeability, clay-rich subunits, thereby enhancing deformation of the slope toe, which, in turn, destabilized the upper portion of the highwall. The outcome was a 160 m high slope failure that had a lateral run-out of 850 m. The effort to return the pit to ore production required geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with localized, blast-induced slope failures. Back-analyses with numerical modeling software indicated that the failure surface could be shallower, which contradicted the initial failure interpretations. Eventually, drilling results confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the subunits with residual strength properties. The results are a stable highwall within the Carlin Formation following nearly 10 years of repeated slope failures, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new openpit development.

By Yuemin Zhao, Wenxuan Liu, Maoming Fan, Zhanyuan Long

"Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium and phosphorus. These coalassociated elements are significantly enriched in coal combustion byproduct fly ash because the majority of the main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main element oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides and unburned carbon.Chinese coal fly ash usually contains about 5 to 15 percent of unburned carbon, which are generally chars with irregular shapes and wide particle size distribution. In addition to unburned carbon, XRD analysis of four Chinese fly ash samples from Liaoning, Shanxi, Guizhou and Shandong provinces indicates that the fly ash samples are composed of minerals such as quartz (SiO2), mullite (3Al2O3.2SiO2 or 2Al2O3.SiO2), hematite (Fe2O3), maghemite (gamma form of hematite, ?-Fe2O3) and magnetite (Fe3O4). The mullite and quartz particles are usually present as spherical particles because they are formed by melting clays, feldspars, quartz, calcite and other common minerals in coal during coal combustion. The silicate particles have usually entrapped gas to yield hollow spherical particles because their lower melting point facilitates gas entrapment.The iron oxides are usually spherical also. The magnetite (Fe3O4) is derived from pyrite (FeS2), hematite (Fe2O3), siderite (FeCO3) and limonite (2Fe2O3.3H2O) in the coal. Maghemite (?-Fe2O3) is formed by dehydration of the mineral hydrohematite (?-FeO(OH)) and/or oxidation of magnetite (Fe3O4) during coal combustion. Maghemite (?-Fe2O3) and magnetite (Fe3O4) are strongly magnetic, so they are recovered from Chinese coal fly ash and widely used for coal processing in China (Fan et al., 2005, 2000)."

Jan 3, 2018

By Karoly (Charles) Kocsis, August Greth, Jon Fox

"It is the duty of the mine operator to ensure the mine environment is healthy and safe for the mine workers. For deep and hot underground mines, this requires maintaining adequate working temperatures by means of mitigating the heat load generated by strata, auto-compression, mining equipment, explosives, ground water and human metabolism. The heat load is best reduced by minimizing the amount of heat transferred to the mine air from these sources and through the use of efficient ventilation with effective cooling systems. The heat emitted by mining equipment and vehicles contributes a significant proportion to the combined heat load of an underground mine. This is especially a problem for diesel equipment due to the fact that besides heat, a large amount of water vapor is produced, which increases the humidity in the production workings. Diesel engines have proven advantageous in recent history due to their high power output and reliability. However, as mines continue to become more mechanized and deeper the climatic problems introduced by elevated heat generation will continue to rise. With that, the issue of heat generated by diesel equipment must be addressed.The economic alternative for diesel engine equipment fleets in underground mines is the electric engine. Technological advances in battery technology, increased mechanical output and improved reliability have made the electric engine significantly more competitive in comparison to diesel engines. Because electric engines do not utilize internal combustion, the heat produced by them is significantly less than the diesel engines. Battery-powered mining equipment likewise eliminate diesel particulate matter (DPM) produced by diesel engines. Utilizing battery electric equipment in underground mines provides many advantages, such as: (a) reduced heat load, (b) healthier and safer environment for the mine workers and (c) reduced mine operating costs due to lower ventilation requirements"

Jan 8, 2018

By S. Mafi

The Broken Aro project is associated with a 1910 abandoned underground mine complex that has been discharging aeid mine drainage from entries, seeps and springs. The Ohio Department of Natural Resources(ODNR), R&F Coal Company (R&F) and American Electric Power (AEP) are involved with this unique project that will remine the abandoned underground complex and install a mine seal constructed of fixated flue gas desulfurization (FGD) material. The goal of the project is to eliminate or reduce the acid mine drainage that is discharging into the watershed. This paper discusses remining, installation of the FGD mine seal, government financed reclamation projects and future application to active and abandoned mining sites.

Jan 1, 1998