Search Documents

By Shaoyang Yan, Xinming Chen, Huazhe Jiao, Huaibao Chu, Chang Wang

In terms of the technical problems of rib spalling in large mining height coal face, a long-distance advanced pre-grouting layer flexible reinforcement technology is proposed in this paper. Based on the mechanism and failure mode of rib spalling in the coal face, the mechanical properties of the aluminum plastic composite pipe were analyzed by using the tensile and compression experiment. The deformation and strength characteristics of “flexible pipe + grouting” specimens were studied by uniaxial compression test, splitting test, and shear test. The UDEC numerical simulation software was used to simulate the reinforcement effect of “flexible pipe + grouting” at different positions. Combined with the field application, the feasibility of long-distance advanced pre-grouting layer flexible reinforcement technology was verified. The test results show the following: The coal face has the characteristics of brittle and large deformation. The aluminum plastic composite pipe has the characteristics of good elongation and tensile strength, which can endure the large deformation of the coal face. The “flexible pipe + grouting” can improve the tensile and shear strength of coal. The UDEC numerical simulation analysis indicated that the grouting hole layout of “flexible pipe + grouting” has a significant difference in the reinforcement effect of the coal face. Compared with single row grouting reinforcement, the reinforcement effect of double row grouting holes 1.5 m and 3.0 m away from the roof is better. According to the field application, it is feasible to use aluminum plastic composite pipe as a flexible grouting pipe to reinforce coal seam with 80–100 m long-distance pre-grouting. Long-distance advanced pre-grouting layer flexible reinforcement technology can improve the daily production of coal and reduce the support cost of the coal face. As a new method of reinforcement, long-distance layered flexible reinforcement has a significant effect on the prevention and treatment of rib spalling in large mining height coal face.

Sep 27, 2022

By Nagashi Ogushi

Geochemical prospecting method using stream sediments, soils and rock chips has been tested to see the applicability for the typical Kuroko field in Japan. Three independent anomalies have been detected in maps being shown by grav densities of cells which are represented by the results of factor analysis as well as distribution of minor elements scaled in logarithm. A small vein type mineralization which has outcrops could be attributed to the origin of them whereas the one near the surface of known Kuroko deposit to a coincidence. The addition of drill core geochemistry is required to complete the interpretation.

Jan 1, 1982

By Sumit Kumar Hota, Asadi Srinivasa Reddy, Ashok Kumar, Ashish Agrawal, Surajit Sinha, Chandra Sekhar, Tanay Ray

In the current operational facility, due to the absence of pellet pot facility, a novel technique is developed wherein the pellets with different chemistries prepared in the laboratory are fired in an induration machine by placing them inside the Inconel baskets. In the present work, an attempt is made to optimize the pellet chemistry by developing 2 different flux pellets, viz., low basicity (B2: CaO/ SiO2 = 0.3) pellets and high basicity (B2 = 0.9) pellets, and further the effects of basicity on pellet properties, viz., cold compressive strength, porosity, swelling index, reducibility index, and softening and melting temperature, are studied. It has been found through the multiple operational trials that increasing the basicity of pellets from 0.3 to 0.9 results into improving the pellet strength, reducibility and softening and melting characteristics. Moreover, it is observed that the swelling index of pellets is reduced by adding 2% MgO to both low and high basicity pellets that could be attributed to the formation of high melting point slag in pellets. The operational trial has resulted into producing pellets that exhibit a combination of desired mechanical strength, improved swelling, and reducibility index and possess better softening–melting behavior among all the chemistries studied.

May 24, 2022

Large deposits of eudialyte, a low grade zirconium bearing mineral, occur on the Southern Coast of Greenland in the Ilimaussaq intrusion. Various processes were tested in the laboratory to recover eudialyte from these ores, including flotation, leaching, gravity and magnetic separation. A combination of dry and wet magnetic separations has the advantage of simplicity and the least environmental impact for the location. This paper summarizes the results of laboratory testwork to develop a two-stage treatment process to recover the eudialyte by magnetic separation.

Jan 1, 1993

By Jafar Safarian, Leiv Kolbeinsen, Stian Seim, Hossein Salehi

The present work aims to investigate the link between the oxidation and reduction of a weathered ilmenite concentrate in terms of phase transitions, microstructural changes, and element distribution. An ilmenite concentrate sample was pelletized and fired at 1000 °C in air, and as a result, the pellets were oxidized. The oxidized pellets were reduced by hydrogen gas at 1000 °C, which yielded almost complete metallization of the iron content of the pellets. The ore and the pellets were characterized in each step by XRD and SEM techniques, and distribution of elements and phases were investigated. Ilmenite, pseudorutile, and rutile were the main phases detected in the ilmenite concentrate sample, and depending on the weathering degree of the particles, different fractions of the phases were identified in their microstructure. It was found that irregular rutile grains dispersed in a pseudobrookite matrix is the morphology of the oxidized ilmenite phase. However, increasing microcracks and porosities were the only microstructural changes in the pseudorutile phase after oxidation in air. Studying the specific types of the ore particles and their oxidized and reduced forms indicated that the phase distribution in the ilmenite ore particles dictates the phase distribution in the oxidized and reduced ones. Results show that the morphology of the reduced particles includes a titanium (III) oxide matrix in which reduced iron globules are dispersed.

Feb 8, 2021

By J. G. Groppo

The Andritz Ruthner Inc. hyperbaric filter was evaluated at a pilot scale for dewatering fine coal cleaned by froth flotation. The pilot scale dewatering testing was conducted at a solid feed rate ranging from 100 lbs to 200 lbs/hr-ft2. Effect of hyperbaric operating parameters and addition of various surfactants and flocculants were evaluated on dewatering of fine coal. The tests data indicated that for the minus 100 mesh and minus 28 mesh clean coal product, the Andritz hyperbaric unit provided filter cake containing 23 percent and 14 percent moisture, respectively.

Jan 1, 1996

By O. Ozdemir

Soda ash, an essential raw material for major industries, such as the glass, chemicals, soap and detergents, pulp and paper, mining and water treatment industries, is traditionally produced by chemical and thermal treatment of trona ore. The treatment processes for trona ore are not only chemically expensive but also energy intensive. Hence, the production of a high-purity trona concentrate at a lower energy and operating cost is of considerable interest to the trona industry. In this study, we describe a possible two-stage process for concentrating trona ore, involving dry magnetic separation followed by flotation, to remove insoluble impurities from the trona ore. The results showed that a trona concentrate of 91.7% purity with a recovery 91.1% can be obtained by two-stage magnetic separation, which could be further improved to 98.1% purity at a recovery of 83.8% by subsequent flotation of the non-magnetic trona product. The purity of trona concentrate is limited by the particle size and impurity content of the trona ore. The operating parameters for magnetic separation and flotation have been identified to obtain an acceptable quality concentrate.

Jan 1, 2011

By Bijan Taheri, Behrouz Maghsodi, Monireh Heshami, Reza Kohan

A common problem recently encountered with the increase in the rate of input feed at Enrichment Plant 2 of the Sarcheshmeh Copper Complex is the loss of value to the tails, translating to lower recoveries. The feasibility of the direct transfer of part of the high-grade concentrate from rougher stages to an appropriate position along the circuit was studied, and two positions were proposed for direct transfer of the concentrate. One position was the feed flow into cleaner cells, and the other was the feed flow into the recleaner cell. The results indicated that transferring the concentrate from the first unit of the rougher stage to the feed flow into the cleaner cells was feasible, with no limitations, while the second position required the installation of a set of hydrocyclones. It was found that the transfer of concentrate to the proposed positions not only addressed the problem of limited cell capacity, resulting in debottlenecking of the circuit, but also improved metallurgical separation efficiency up to 1.4%.

By W. R. Reed, Y. Zheng

A recent study conducted by the National Institute for Occupational Safety and Health (NIOSH) evaluated the roof bolter canopy air curtain (CAC) systemin a blowing face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. This study evaluates the roof bolter machine CAC while operating in an exhausting face ventilation system. This study considers two similar locations to allow comparison with the previous blowing face ventilation (Zheng et al., Min Metal Explor 36(6):1115–1126, (2019)) study: (1) a roof bolter machine bolting the roof at 20 ft (6.1 m) from the face and (2) a roof bolting machine bolting at 4 ft (1.2 m) from the face. The environment introduces 6.0 mg/m3 of respirable dust to represent the roof boltingmachine operating downstreamof the continuous miner. However, the exhausting face ventilation uses an exhaust curtain with 9000 cfm (4.25 m3/s) of air. Two roof bolter machine working positions are simulated with the use of dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8%. When the roof bolter machine operated close to the face, increasing CAC airflow was required for adequate protection since the dust reductions can be as low as 39.5%. Additional CAC airflows of 350 cfm(0.17 m3/s) and 450 cfm(0.21 m3/s) were evaluated and demonstrated that dust reductions increased to 59.7% (350 cfm) and 72.0% (450 cfm) for the worst location where the roof bolter operators located.

Aug 26, 2020

By Qingwen Shi, Gang Xu, Shuwen Wang, Brijes Mishra

Pressure relief borehole is one of the most effective methods to treat coal burst in deep-buried coal seams. However, due to the large amount of randomly distributed fractures in the coal body and the varying stress environments in underground coal mines, there is no practical method to assess relief boreholes by far, which brings problems for borehole design and construction. This study focuses on the assessment of relief boreholes in a single driving entry wherein the impact of mining panels on relief boreholes is eliminated. A practical method, focusing on field monitoring of borehole deformation with a new device, is developed to evaluate the single driving entry’s relief boreholes. This method is applied to a Chinese coal mine. The application results showed that the convergence process of the boreholes showed a three-phase characteristic. Phase one involves the fastest deformation, reaching up to 8% in the first 3 to 4 days. Phase two lasts longer and converges more, reaching up to 30% in 4 months. Phase three stays balanced until the excavating face moves. The three-phase characteristic indicates that a large diameter of the borehole ensures relief efficiency because the borehole provides adequate space for deformation throughout its life span. In addition, it is verified that long boreholes and slow footage improve relief efficiency by providing adequate time for the boreholes to work. The application proposes that boreholes in the test coal mine need to be drilled larger and longer for optimization.

Oct 19, 2021

By Kenneth L. Maloney

Ten small and intermediate-sized [11 GJ/hr to 264 GJ/hr (10,000 lb/hr steam to 250,000 lb/hr steam)] coal-fired boilers in the upper Midwest have each been tested on both a bituminous eastern coal and a subbituminous western coal. The purpose of this study was to determine the feasibility of substituting western subbituminous coal for eastern bituminous coal as a means of reducing the SO x emissions from this class of boiler and to demonstrate the feasibility of greatly expanded western coal utilization as a means of reducing the use of oil and gas. The scope of this study was such that the representative boiler types were tested on both eastern and western coal for a period of time sufficient to completely characterize their individual emission and operational characteristics.

Jan 1, 1977

By Rameshwar Sah, Basavaraja Maribasappanavar, Sangamesh Desai, G. Balachandran, Ravi Kant Sagar

The present research work deals with the effective utilization of hematite ore containing goethite, kaolinite and gibbsite losson- ignition (LOI) phases in pellet making without deteriorating product pellet properties by optimizing the induration cycle especially drying and preheating of pellets. Adequate drying and preheating of pellets before sintering is of prime importance to sustain the desired properties of pellets. Green pellets of + 8 to − 16 mm size were prepared in a laboratory disc pelletizer and indurated by varying drying and preheating temperatures in a laboratory Raising Hearth Furnace (RHF). Produced pellets were assessed for physical and metallurgical properties. Improvement in drying and preheating temperature simultaneously helped in mitigating fired pellets’ property deterioration. Drying at 300 °C and preheating at 750 °C helped in the maximum removal of matrix LOI from the pellets before firing and enabled the production of pellets of desired properties. Laboratory scale findings successfully implemented at existing 4.2 MTPA capacity pellet plant of JSW Steel Ltd. Vijayanagar and high LOI iron ores (IOs) utilised which resulted in reduction of average monthly pellet fines generation by ~2 wt. %.

Jun 4, 2022

By Alphonce Wikedzi, Mussa D. Budeba, Samwel V. Manyele, Sospeter P. Maganga

The present study provides an overview of the challenges and opportunities in processing complex gold-copper ores. The systematic literature review was conducted using Scopus database and seven-step methodological approach. The study indicates that the major challenges in processing complex gold-copper ores through the conventional cyanidation method include (1) increase in cyanide consumption; (2) increase in cyanide destruction cost; (3) low gold recovery; (4) decrease in adsorption efficiency; (5) decrease in electrowinning efficiency, and (6) difficulties in the measurement of free cyanide concentration in the leaching system. Moreover, the study indicates that several methods have been developed and some have been implemented in the mining industry for processing complex gold-copper ores. This includes ore segregation, pre-aeration, pre-treatment methods (e.g., ammonia), alternative lixiviants (e.g., thiosulfate, thiocyanate, glycine), cyanide destruction methods, and cyanide and copper recovery technologies. The study concluded that using lixiviant mixtures (e.g., cyanide-glycine), pre-treatment with environmentally friendly reagents (e.g., glycine) and the integrated membrane-based process (SuCy process) are new directions in processing complex gold-copper ores. However, more investigations are required to advance these processes to a commercial scale.

Sep 30, 2023

By Qingwen Shi, Yun Zhao, Brijes Mishra

The effect of discontinuities on the fracturing and mechanical behavior of shale has been extensively investigated on a laboratory scale in previous works. It is well agreed that the lamination properties, including discontinuity and lamina properties, affect the behavior of shale. However, it is still unclear how the lamination properties are affecting the stability of the shale roof in an underground coal mine entry. This paper investigated the effect of lamination properties using the discrete element method on a mine-scale entry model as an extension to the previous work conducted on laboratory scale models.

Jan 11, 2022

By Sunny Murmu, Gnananandh Budi

One of the most significant concerns in longwall ground control is the instability and failure mechanism of the coal wall. The current research uses FLAC3D to simulate panel 1 of the Adriyala Longwall Project, India, in order to evaluate the distribution of vertical stress and material failure mode, in and around the longwall face. Additionally, three distinct criteria are used to evaluate coal wall spalling: vertical stress distribution, maximum shear strain, and residual cohesion. A novel algorithm is also proposed to appropriately capture roof bed caving, shield installation and advancement, and coal extraction from the face. The findings of the modelling show that progressive longwall extraction creates an elliptical stress relief zone around the excavation void. During the peak stress phase, the height of the stress relief zone is greatest, whereas the width is highest during the main fall phase. As mining advances, the coal wall at the face line appears to lose its stress-bearing capability. Shear failure was the most common coal wall failure mode. Maximum spalling depth (MSD) and longwall face spalling index (LFSpI) were used to measure the extent and volume of coal wall spalling in FLAC3D. For panel 1 of the ALP mine, the MSD, and LFSpI were determined to be 3 m and 90.5 %, respectively. The mode of coal wall spalling was expected to be total or fragmented failure. The field observations and the numerical modelling findings were in good agreement. The compressive strength and deformation modulus of the immediate roof appear to have a substantial role in coal wall spalling. The results of the proposed numerical simulation exercise can help strata control engineers better detect the risks of coal wall spalling and enhance face control for safe and productive working environment at the longwall face.

Aug 8, 2023

By F. Freme

Coal production in the United States in 2009 de-creased to 972.8 Mt (1,072.8 million st), according to preliminary data from the U.S. Energy Information Administration (EIA). This is a decline of 8.5 percent, or 90 Mt (99.1 million st) below the 2008 record level of 1.06 Gt (1,171.8 million st) (Table 1). In 2009, U.S. coal consumption decreased in all sectors while total coal stocks increased for the year. Coal consumption in the electric power sector in 2009 was lower by 10 percent, while coking coal consumption decreased by 30.6 percent and the other industrial sector declined by 16.6 percent. The commercial and institutional sector (which prior to 2008 had been called ?residential and commercial?) is the smallest of all the coal-consuming sectors and it declined by 8.4 percent in 2009. (Note: all percentage change calculations are done at the short tons level.) U.S. coal exports fell from the 2008 levels, while coal imports decreased for a second year in a row. The decline in coal consumption during the year was the consequence of the domestic economic conditions combined with the weather in 2009, which resulted in lower demand for electricity. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. decreased in 2009. Coal-based generation also decreased, resulting in a 94-Mt (104-million st) drop in coal consumed in the electric power sector. Coal use in the non-electricity sector decreased by 20.1 percent to a level of 57.9 Mt (63.9 million st). The international coal markets for most of 2009 were reflective of a worldwide economic slowdown. U.S. coal exports and imports both declined for the year. U.S. coal exports totaled 53.6 Mt (59.1 million st). This is a decrease of 20.3 Mt (22.4 million st) from the 2008 level.

Jun 1, 2010

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling both dust and gas. Redirecting all the air towards the face equally up both sides of the machine increased both the dust and gas concentrations around the machine. When all the air was redirected towards the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all the scrubber exhaust was redirected towards the face either up the off-tubing side or equally up both sides of the mining machine.

Feb 23, 2014

By K. V. Raj

As open pit mines continues to grow deeper, managing air pollution can become challenging. During arctic air inversion, the temperature of the air over the mine increases with altitude, and the cold, heavy, surface air is trapped in the pit. This problem is complex, and any solution will require an extensive understanding of the interactions between the aerodynamic movement of air, air inversion, meteorology, pollutant sources, and transport phenomena in the open pit mines. The availability of computational fluid dynamics (CFD) has elucidated the pollutant flow mechanism in open pit mines. Very few CFD studies have been published, especially the Large Eddy Simulation (LES), on the contaminant transport in deep open pit mines under arctic air inversion. The contaminant transport in an open pit mine under arctic inversion is due to a stable or nocturnal boundary layer in micro-meteorological terms. Understanding the physics of the stable boundary layer (SBL) is relevant to air flow and pollutant transport in deep open pit mines. This paper focuses on a Large Eddy Simulation (WMLES as Sub-Grid Scale Model) modeling of the SBL and pollutant transport in a large open pit mine.

Feb 23, 2014

By Virgil L. Barr

National income originating compared to physical production for an enterprise or an industry reflects its ability to strengthen the national economy. For a single industrial sector or for an industry this comparison can be useful to reflect changes that may occur in this ability to contribute because of changing supply-demand-income-investment equilibria. A favorable relationship can be postulated by specified economic incentive, and the accompanying technologic input required can be shown. The new index proposes the use of the Federal Reserve Board indexes of production divided by the constant dollar income originating in the petroleum industry which reflects increases or decreases in performance. When compared with other mineral industries and with, total industry, an approximation of relative strength is evident. By constructing three different hypothetical conditions for future petroleum imports, assuming a constant excess capacity requirement for domestic production, and providing an estimate for future domestic demand for petroleum, the impact on the performance index can be shown. Thus, a strong position for the petroleum and natural gas industry can be stated. If this is done, it becomes evident that because of restrictions on cost-price relationships, a drilling program that would provide enough domestic oil to meet demand may not be practicable. By difference, the amount of improvement in methods of production and processing through technologic advancements can be stated explicitly.

Jan 1, 1960

By A. E. Foscolos

British Petroleum (BP, 2005), indicates that world reserves for oil to be 1198 billion barrels, for natural gas the equivalent of 1156 billion barrels of oil and for coal the equivalent of 3219 billion barrels of oil. If we take into consideration the mean aver-age annual increase in demand of the last three years for oil, 2.6%, for natural gas, 3.9%, and for coal, 6.6%, then their respective reserves? lifespan are calculated to be 27, 34 and 38 years. Without taking into account their annual increase in demand, lifespan increases to 38, 67 and 161 years respectively. Since zero increase or perpetual increase in energy demands on finite resources is unrealistic the selection of the most suitable energy commodity for power generation rests upon the law of supply and demand of each commodity. This defines its price hence its selection for the production of cheap electricity. When the ratio of supply to demand is less than one, peak production is achieved. Any further increase in demand results in price increase to quench its demand. The Association for Oil and Gas Peak (ASPO) has calculated that when oil demand exceeds 84 million barrels/day, Peak Oil Production will be attained thus prices will start to increase in order to even demand with supply. Correspondingly, Gas Peak Production is expected to take place when demand exceeds 9.1 or 10.2 billion cubic meters/day. Peak Oil production has been calculated to take place in the current year, 2006, while Gas Peak production is estimated to take place between 2020 and 2025 provided that gas will not cover the energy deficit created from the lack of oil otherwise Gas Peak production could arrive as early as 2010. The use of coal for power generation is considered a better alternative than oil and gas if new combustion technologies with an energy efficiency of 43%, Germany, and 47%, Denmark, are adopted. These not only extend the lifespan of coal reserves but reduce also CO2 emissions by 25% and 31%, respectively. In the very near future CO2 sequestration and fixation in deep geological strata will eliminate its emissions thus rendering the use of coal the cheapest feedstock for power generation.

Jan 1, 2006