Search Documents

By Wendell E. Bearce

At the, Crescent Valley Mine of the Hanna Coal Company, several 10,000 ton unit trains of 41" x 0 strip coal are loaded per week during the lake season. This is accomplished without the use of any accumulation of prepared coal. A large raw coal pile is built up during the winter months adjacent to two truck dump bins. This is added to whenever trucks are coming in from the pits and trains are not being loaded. During the loading of trains, trucks from several pits dump into the truck hoppers and coal is also dozed in from the pile. At a rate up to 3200 tons per hour this coal is screened, the plus 6" hand picked, the plus 4" crushed, and' all weighed and sampled as it goes directly to railroad cars being handled on two tracks by car retarders. With such an arrangement it is possible to exercise some control over coal quality, if it can be assessed rapidly. For instance, if the moisture rises to a level where it seems probable the BTU per pound will be reduced to the point where the contract calls for penalties, the trucks from, the wettest pit may be stopped, more or less coal may be moved in from the stockpile, or other measures taken to assure that the average BTU of the trainload will be satisfactory.

Jan 1, 1967

By H. Lyn Bourne

This marks the 15th consecutive year for this column. During 1995, readers were asked to supply royalty data for construction raw materials especially for states where none is available. The response was discouraging and royalty data are still missing for several states for either sand and gravel or crushed stone. Several readers have said that this article has merit but more new information is needed to justify its continuation. Several articles and pieces of news relative to mineral royalties appeared in the trade journals. R. Lee Aston (E&MJ, November, 1995, p. 16N) described South Australian royalties as amended by the government in1994. The royalty rate (a percentage) was lowered but the assessed value for minerals was raised and the current rate amounts to 20 cents//t (18 cents/st).

Jan 1, 1996

By William F. Lawrence

Within ten to fifteen years, coal-fired power generating stations will be producing over 40 million tons of coal-ash annually in the United States. The largest part of this ash will be emitted from the boilers, entrained in the off-gas stream and trapped as flyash. However, about 15 percent (six million tons) will he removed from furnace bottoms as bottom ash or molten coal-ash slag. In current practice, the molten coal-ash slap is generally water quenched and then transported either as a slurry or in granular form to storage or disposal areas. Although a small amount of this slag is marketed as abrasive grit or as roofing granules, most of it is considered a waste material which must be disposed of at considerable cost to the power companies and therefore to the public. The accom¬panying economic loss in terms of unused raw materials and displaced land is not as obvious but is just as real. The Coal Research Bureau at West Virginia University under the sponsorship of the U. S. Bureau of Mines has been examining the possible utilization of both coal-ash slag and flyash in the mineral wool industry as a method of partially alleviating the growing national problem of solid waste disposal. The potential marketing situation for mineral wool manufactured from coal-ash is illustrated in Figure 1. This bar graph depicts the growth in value of mineral wool shipments1 from 1949 through 1966. In this 17-year period, the value in¬creased by over 350 percent, more than 20 percent per year, despite a decrease in unit cost of mineral wool. It therefore appears likely that coal-ash could find a steady market as a supplement to existing sources of raw materials for mineral wool production.

Jan 1, 1970

By E. Galán

The largest Spanish kaolin deposits formed on granites occur in Galicia (NW Spain) due to a widespread kaolinization of Variscan granitoids. This paper provides insight of the origin of this kaolinization process on the basis of a mineralogical and geochemical study carried out in two kaolin deposits, presently mined to be used in the paper industry. Mineral composition of the deeply kaolinized rocks is dominated by well-ordered kaolinite with minor quartz, K-feldspar, mica (illite/muscovite), locally gibbsite, and traces of resistant accessory phases (rutile, ilmenite, zircon and monazite). The content and structural order of the kaolinite decrease with depth. Kaolinite formed by extensive replacement of feldspars (plagioclase). Differential mobilization of major and trace elements during kaolinization has been inferred by using a mass-balance approach. Significant amounts of Na, Ca and minor Mn, Sr, P and U were removed from incipiently leachable minerals (plagioclase and apatite), and K, Rb, Cs and Ba were released from K-feldspar and mica. On the contrary, Ti, Zr, Th, Hf and the REE are retained in the resistant trace minerals that are concentrated in the fine fractions of the kaolins.

Jan 1, 2010

By H. Hoberg, M. Langen, B. Hamacher

Since the term "abandoned hazardous sites" was first coined in the 1978 environmental report of the Council of Environmental Specialists, a number of different types of technology has been developed in the Federal Republic of Germany for the remediation of contaminated soils /l/. At former sites of the mining industry, such as metallurgical and coking plants whose soil has been contaminated by organic and inorganic pollutants over decades of industrial activity, there is an exceeding necessity for soil remediation. Also, many former locations of metal processing works, battery factories or scrap yards have been contaminated in particular by heavy metals. Wet mechanical soil decontamination has proven successful over the past 10-15 years in the purification of these soils The process goal is the enrichment of the pollutants in certain plant products and the separation of a pollutant concentrate from the decontaminated soil. Table 1 lists the steps of the highly advanced wet mechanical soil decontamination process to achieve this process goal. Table 1 lists both the name of each process step and its goal in terms of a direct separation of the pollutant or the preparation of the soil for subsequent separation steps. For the separation of heavy metals, density sorting and separation techniques utilising flotation were specifically used. The use of chemical auxiliaries such as acids and lye is limited to special cases because these in themselves produce additional environmental impact and the economical effficiency of these techniques compared to conventional methods is lowered by supplementary process steps for water purification. The subject of this presentation is to consider how soil decontamination processes can be effectively improved through a description of the material properties of soils contaminated by heavy metals, and through carrying out basic investigations about the adsorption of heavy metals. Soils of different origins, especially those from former mining and metallurgical sites, were used for the experiments.

Jan 1, 1995

By Reed S. C. Rogers

There is recent evidence that high frequency screening can be a viable alternative to hydrocyclone classification for a wide variety of grinding applications. However, since high frequency screening is a relatively new development, the decision to use screens generally must be based on full scale screening tests of a slurry material of interest. In this paper the authors employ mathematical simulation models as an aid to evaluating the use of screens versus hydrocyclones for closed circuit fine grinding. This approach is validated in a pilot plant study and then demonstrated for the design of full-scale grinding circuit, including classifier cost comparisons. For the case of maximum production rates versus product size, without a constraint on fine product solids densities, results indicate that screening with Derrick sandwich type cloths can give higher grinding circuit production rates with more narrowly sized products than when hydrocyclones are used. These results are explained in terms of the bypass and Sharpness Index of the respective classifier partition curves. Classifier cost comparisons for the full scale circuit show that although the installed cost of screens is substantially higher than equivalent capacity hydrocylone operations, even modest increases in circuit capacity caused by screens; can significantly reduce total grinding costs.

Jan 1, 1985

By N. Myung, G. Hwang, H. Kim, Y. Han, S. Choi

"According to research presently being conducted on selective lithium recovery in seawater, inorganic adsorbents with high selectivity and capacity for capturing lithium ions from liquid lithium resources are called lithium ion-sieves (LISs). Their low toxicity, low cost and high chemical stability make LISs suitable for lithium recovery from seawater. In the present study, the ultrathin LMO nanofibers with controlled diameter were successfully fabricated by an electrospinning technique with a hypothesis that greater aspect ratio (i.e., smaller diameter) would lead to the enhanced recovery of lithium ion from seawater. Design of Experiment (DOE) and dimensionless analysis were performed to systematically optimize the diameter and morphology of nanofibers. Several complementary techniques including FE-SEM and XRD were used to evaluate the physical/physicochemical properties of the nanofibers. Lastly, the lithium ion recovery was tested for the nanofibers with different physical properties using lithium ion solution. INTRODUCTION Demand for lithium resources is increasing in many industries across the world.1-2 However, the conventional resources for lithium is very limited, and it even gets worse to secure the resources due to low grade and/or complexity of feed materials. Much effort has been, therefore, devoted to obtaining lithium from aqueous lithium resources. Several methods such as solar evaporation3-4, co-precipitation5, and solvent extraction6 have been proposed for recovering lithium from an aqueous lithium source, but there are limitations on its use; It takes a very long time or conditions such as temperature, pH and Mg/Li ratio are severe. Lithium ion-sieve (LIS) materials are considered as a good lithium adsorbent because of their unique chemical structure that can selectively separate lithium ion from brine and seawater.7- 10 Furthermore, their low toxicity, low cost, and high chemical stability make LIS suitable for lithium recovery from aqueous lithium resources. Spinel hydrous manganese oxide (HMn2O4) derived from spinel lithium manganese oxide (LiMn2O4) after topotactically extracting lithium from the spinel structure by acid treatment is most widely investigated LIS.10, LIS materials have been actively studied in various forms for easy handling and high efficiency (i.e. membrane11,12, foam13-14, granular15,16). Among them, the 1-D nanostructure LIS with high specific surface area is excellent in efficiency.9 In this study, we present the part of our recently submitted work17. Specifically, we fabricated systemically lithium manganese oxide nanofibers with different diameter as a lithium ion adsorbent using electrospinning technique through design of experiment (DOE). Enhanced lithium ion adsorption properties of the HMn2O4 nanofibers with different diameter were investigated in lithium liquid resources."

Jan 1, 2018

By R. H. Sergent

The interest in using halogens for extracting precious metals from ores has increased due to changes In ore characteristics, environmental concerns and regulations. The rediscovery of halogen leaching capability has been the topic of these and other writers1-30. Much work has been done on the performance of bromine, chlorine and iodine5-29. Of these, bromine and chlorine look most promising. Iodine is quite expensive and sometimes forms an Insoluble film on a precious metal surface22,23. Little experimental work has been published on the relative performance of bromine versus chlorine. The Pourbaix diagrams for the halide leach system (see Fig. 1-4) Indicates a significant stability advantage for bromine In forming complex ions with gold. This should result In greater extraction of gold under similar leach conditions and Is evaluated In this work. The regeneration of halogen from a spent leech solution is a critical requirement for an environmentally acceptable halogen leach process. Bromide can be oxidized In-situ to bromine ~ adding chlorine or ozone2,31. Bromide like chloride can be oxidized In an electrochemical cell to produce halogen on demand 13,15,17. Bromine clearly offers a number of possible regeneration pathways. This work strives to compare the relative ability of chlorine and bromine to extract gold from partially and fully oxidized ores. A commercially pressure oxidized sample was evaluated under a number of experimental conditions. The autoclave feed ore from the same mill was also evaluated after complete oxidation In a laboratory autoclave.

Jan 1, 1993

By George L. Wilhelm

Many factors, some of which are not easily defined or described, must be considered in the design of a hydraulic backfill system. After participating in the design of several plants, I have a conviction that future refinements in sandfill systems must come in large part, from the merging of good design ideas and information from existing operating plants. It is important then, that we document and publish information on existing plant designs and their operating characteristics. This information will then be available for use by our successors and later innovators in hydraulic fill placement. The Mayflower hydraulic sandfill system is similar to other plants. The intent of this paper is to describe only this system's unique design and operating characteristics. I will not describe in any detail, the familiar elements of the system. I will document some of the observed hydraulic characteristics of the system, elaborate on some of the design situations that had to be solved, and will discuss operating factors that are not generally described in our technical literature.

Jan 1, 1968

By E. Steiakakis

This paper presents in detail the procedures followed and the results obtained in order to determine the stiffness parameters of the calcareous marls found in the lignite mines in Ptolemais, Northern Greece. Triaxial tests were performed on representative samples of the inner burden marl and the marl which underlies the lignite bearing series of the region. The tests were conducted under drained conditions, with controlled loading (including an unloading-reloading loop), while the axial strain was measured externally as well as with displacement transducers mounted directly on the specimen (Hall Effect sensors). The geotechnical parameters obtained (i.e., cohesion, angle of friction, stiffness modulus, stress-strain relationship), were subsequently used for simulating the triaxial testing with the Plaxis finite element software. Simulation results are in good agreement with the experimental results. The resulting material model can then be applied to modeling the mobility that is expressed during the excavation of the open pit mines.

Jan 1, 2005

By Adam Feiler, John Ralston

Optical reflectometry was used to study the attachment and subsequent detachment of silica particles (diameter 25 nm) from the surface of titanium dioxide wafers under well-defined hydro- dynamic conditions. Atomic force microscopy was used to measure the interaction between silica spheres (diameter 7 pm) and titanium dioxide wafers under the same solution conditions. In addition to repulsive electrical double layer forces, adsorbed polyphosphates provide a short-ranged steric layer that reduces the lateral interaction between the surfaces. The use of these two complementary techniques has given valuable insight into the process responsible for fine particle detachment and has particular application to surface cleaning.

Jan 1, 2003

By James Wm. White

Computer-based mine management systems are being used in many surface mines to assign haul trucks, track equipment and manage information. Advances in digital communications allow these systems to be used in underground operations. Underground mine management systems help maximize production by providing gains in equipment and manpower use, drawpoint equalization in block caving operations, preventive maintenance and safety. Current systems use allocated or "locked" train and load-haul-dump (LHD) dispatching. Allocated dispatching rarely optimizes open pit product' on. But it offers an efficient mode of operation underground and where options are more limited. The primary objectives of underground mine management systems are to maximize production and mini¬mize contention time through allocated train, truck or LHD dispatching, traffic control, equipment monitoring and comprehensive reporting. The main components of an underground mine management system include: ? A central computer (personal computer or worksta¬tion) in a central control center. It sends instructions to train, truck or LHD drivers and allows dispatcher interaction. ? A field computer system (FCS). This consists of a touch-screen graphics console (GC) and mobile hub - on each train, truck or LHD to receive and display instructions from the central computer and accept driver input. ? A data radio network based on leaky feeder (data, voice, video) or microcell radios (data only) and advanced token-ring technology. This passes information between the central computer and the FCSs. ? Radio frequency (RF) tags mounted at boxes, weigh bridges, tips and rim tunnel main haulage ways to locate trains or LHDs (Luke, 1993). Such a management system must be in place before implementing computer-based dispatching (Vagenas, 1991) for production optimization.

Jan 1, 1997

By I. Y. Bausov, L. G. Stolarczyk, R. E. Pillmore, A. J. Hillard, J. T. Duncan

"Prevalence of lung disease in younger miners surprised industry regulators, congressional members, researchers and black lung clinic staff members. Mitigation researcher focused on low-coal mining in the Appalachian regions until Miners Colfax Medical Center (MCMC) Black Lung Clinic examinations discovered 25 of 72 Wyoming coal miners with lung disease. To reverse recent upward trend in lung disease, research programatic have been directed at reducing exposure to respirable “float” dust. This paper suggests broadening the scope of research to include boundary detection in efforts to improve outcomes. Beginning with a better understanding of biochemistry of anaerobic bacteria methylation processes precipitating sulfur and heavy metals into thin seam boundary layers. Expanding research and development objective to focused on minimization of bit-pick crushing cone volume and preventing mining thin boundary coal layers and out-of-seam dilution. Black lung clinical evaluations of miner will confirm outcomes directed towards reduced occupational disease and smoke stack emissions. INTRODUCTION Miner exposer to bit-tip crushing cone volume, fragmentation and auger movement generated respirable “float” dust and boiler emissions are related science-technology –engineering-mathematics (STEM) problems. Formidable but not intractable problems are driven by oxidation of upper flood plain elements in the periodic table and biochemical metabolic presses occurring in coal basin. Because of burial compaction, quartz and trace heavy metals (Fe2+, Mg2+) are concentrated in thin seam boundary layers. By not cutting through thin boundary coal layer and out-of-seam into hard quartz containing rock layers, miner lung disease and smoke stack emissions are minimized. Cutting bit-pick elastic wave hydrodynamic principle force vectors in the coal layer must be aligned to minimize respirable dust generation, constrained by fragmentation size. Dust abatement by water spray and machine design are effective; but for, failure to address cutting cone dust volume generation and its distribution along run-of-mine (ROM) transportation systems the boiler. Real-time precision thickness measurements by integrated cutting drum (icDrum) sensor, machine man-interdiction from a dust free control room, is a cost effective way to prevents respirable dust exposure. The recommended STEM research and demonstration initiative addresses issues raised by discoveries of increased rate of lung disease discovered in young miners and concerns over emissions from coal-fired electric generation stations (Global Warming). In-mine demonstrations must be validated by on-site MCMC mobile Black Lung Clinic data acquisition and analysis."

Jan 1, 2016

By Fred Heivilin

A symposium on the characterization and toxicology of mineral dusts was held Sept. 19 and20 in Washington, D.C. The symposium was held to update the minerals industry, the health community, government agencies and academia on the technical, health and regulatory aspects of minerals to be evaluated by the International Agency for Research on Cancer (IARC).In October 1996, the IARC met in Lyon, France, to discuss and prepare “Volume 68 of the IARC Mono-graphs on the Evaluation of Carcinogenic Risks to Humans on Silica, Silicates, Dusts and Organic Fibers.”

Jan 1, 1996

By M. R. Yalamanchili

Recently, noequilbrium electrokinetic measurements using laser-Doppler electrophoresis were reported by Miller et al. (1992) for alkali halides and the sign of their surface charge thus determined. These results are generally as expected from simplified lattice ion hydration theory with KCI, under normal circumstances, being the most significant exception. In this regard, lattice defects (F centers and oxygen imperfections) have been found to influence the surface charge of KCI and its electrophoretic mobility. In particular, the presence of oxygen defect states in the crystal lattice has been found to be responsible for KCI's unexpected behavior. The concentration of oxygen defect states in KCI, as characterized by UV/Vis absorption, was varied in order to study their influence on the electrokinetic behavior and subsequently on the flotation response of KCl. At low oxygen contents « 60 ppm) KCI is positively charged as expected from lattice ion hydration theory. However, typically, KCI contains substantial oxygen (>300 ppm) sufficient to impart a negative surface charge which accounts for the selective flotation of KCI from NaCl by hetero-coagulation with oppositely charged alkyl amine hydrochloride collector colloids.

Jan 1, 1994

By P. Zhang

Previous studies have shown that separation of clay minerals from non-clay minerals is the key to economic recovery of the phosphate from the waste phosphatic clays (slime) which represent about 20- 300/0 of the phosphate mined. Small hydrocyclones of different sizes (4" and 6") were tested for sizing the slime at +10 microns in order to remove most of the clay minerals. The effect of design variables and operating parameters were evaluated. Multi-stage cycloning and the effect of dispersant were also investigated. Chemical and mineralogical analyses of different size fractions of both the underflow and overflow samples indicated satisfactorily separation efficiency.

Jan 1, 1998

By F. L. Jackson

The large scale transportation and storage of sulphur in the liquid state is a relatively new development, but is really only a logical extension of old mining and processing techniques, It is not known who the first person was to win a relatively pure sulphur from ore by melting, but this method was commercially used at least two hundred years ago in Sicily and is still in use today. The Frasch process of mining was invented over sixty years ago, and the development and improvement of-liquid sulphur pumping and handling techniques has paralleled the growth in the Frasch mining industry. During the last fifty years, improvements in the technology of using sulphur have included the premelting of sulphur prior to its being burned for acid production or conversion into CS2 and other compounds. Yet, until fairly recent times, sulphur produced as liquid has been solidified into large blocks at the producing point, broken down by blasting or with mechanical equipment, and shipped in bulk form as a solid.

Jan 1, 1962

By John M. Hill

Automation technology has many facets, some well tested and proven, some yet to be put to the acid test of economic reality. In this paper, we will limit our purview to the former. Consider, if you will, an automated handling system combining high-speed conveyors and automatic devices on-line which not only provide signals for routing and sorting, but also format those signals for the production of manufacturing, inventory, shipping and billing paperwork. This is not futuristic, but practical and a realistic accomplishment. Therefore, the following discussions will address today's challenges not with tomorrow's solutions, but rather, with an established technology which is playing an increasingly prominent role in materials handling systems. Until recently, relatively modest importance has been attached to the timeliness of information feedback from the production or assembly line, warehouse or distribution center. Thus, initial applications of automatic identification equipment focused almost exclusively upon the control of materials flow - that is, routing, sorting, etc. However, these systems have performed successfully and quietly established an enviable track record as reliable materials control tools.

Jan 1, 1973

By Katerina Adam

During wet grinding the electrochemical interactions between grinding media and pyrrhotite not only accelerate the media wear but also adversely affect the flotation response of the sulfide mineral. A possibility of remedying the adverse effect on its floatability by applying electric potentials to grinding media was examined. Flotation tests, Auger electron spectroscopy and x-ray photoelectron spectroscopy were used to study the surface properties of pyrrhotite. Although anodic polarization of the steels increased the metal loss by corrosion, the flotation recovery of pyrrhotite was increased. In the case of cathodic polarization, the flotation recovery improved in a narrow range of overpotentials. At higher cathodic overpotentials, however, the floatability of the mineral was progressively lowered although the corrosive wear of grinding media might be reduced.

Jan 1, 1984

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986