Search Documents

By R. R. Klimpel

This paper discusses the effect of water chemistry, reagent type, and other environmental factors on the performance of sulfide mineral size reduction and froth flotation processes. Two specific problems will be discussed: 1) the importance of appropriately utilizing the electrochemical window that is created in the grinding process to enhance sulfide mineral recovery by froth flotation; and 2) the impact of steel grinding media versus autogenous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources.

Jan 1, 1996

By R. D. H. Bedd

GEOLOGICAL NOTES The area under discussion is situated approximately 150 m north of Loraine No. 3 shaft at ± 1500 m below surface. The block being mined extends from about halfway between 50 and 52 levels to just below 48 level (see Fig. 1). The EB reefs form the lower portion of the EB zone of the Elsburg series and in the 81 line area the various conglomerate bands show the best development. Up to 18 separate reef bands are developed and the distance from the bottom conglomerate band to the top is ± 26 m. The thickness of the quartzite which forms the middling between the various reef bands varies from 0.1 to 2 m. The strike is roughly north-¬south. The reef bands are payable individually. However, owing to the steepness of the reefs and their close prox¬imity, conventional mining would prove very difficult. The nonpayable reef bands all carry varying amounts of gold and the whole area is a massive payable reef body approximately 26 m wide and 60 m high at 300 to 400 m on strike. The major structure of the area consists of a north¬-south trending syncline. The western flank of the syncline has a steep easterly dip, in places approaching the vertical. This flank cuts out against the overlying rocks of the EA zone. The latter forms a noncon¬formity with the underlying EB zone. The eastern flank of the syncline dips to the west at an average dip of 0.17 rad (10°). The 0.1 rad (6°) north-plunging syncline was sub¬jected to severe faulting. The most important are the Nos. 4 and 10 faults, both of which have a roughly north-south strike. The No. 4 fault dips to the west at an angle of 1.04 rad (60°) with a downthrow of approximately 150 m to the west. The dip of the No. 10 fault is 0.69 to 0.81 rad (40° to 50°) west, with the western block having moved 150 m updip relative to the eastern block. The EB reefs are being mined by the sublevel stoping method down from the sub-outcrop position to the cutoff against the No. 4 fault. On the downthrow side of the No. 10 fault, that is just above the 54 level, two reef bands are payable and will be mined conven¬tionally. ROCK MECHANICS From the section in Fig. 1, it can be seen that the area under consideration is surrounded by stoped-out areas. This will naturally change the stress distribution extensively. The only way to calculate the stress field for such a geometry is to use the finite element method. It was established that this method worked for the present geometry and so the method was applied to predict the stress behavior of the final geometry. From the results, it appeared that the effect of the old stopes was to destress the area. There are, however, some areas-such as the 50 and 48 north footwall haulages-which will require continuous attention. In these two footwall haulages, deterioration can take place due to tensile stress which

Jan 1, 1982

By William A. Cline

The iron mine and beneficiation facilities of Marcona Mining Company are located on the coast of south central Peru. The facilities include an open pit mine, crushing, concentrator containing grinding, magnetic-separation and flotation facilities, pelletizing plants and a completely self sufficient infrastructure. Total production capability is about 10,000,000 DLTPY, of which almost 6,000,000 DLT result from the fine-grind magnetic concentrate. Over 1,500,000 DLT of fine-grind concentrate is obtained from processing high-pyrrhotite ore. Although the orebody contains quantities of oxidized primary ore and transitional ores (mixed magnetite and hematite), the principal ore is predominantly a coarsely crystalline to fine grained massive magnetite.(l-3) In the primary ore the major impurities found are silicates and the iron sulfides- pyrite and pyrrhotite. Sulfur levels typically average about three percent although levels of five percent are not unusual and some ores contain up to ten percent total sulfides. In general the silicates and pyrite are readily rejected from finely ground primary ore by magnetic separation and very basic froth flotation processes. The high iron, low sulfur concentrate produced is particularly suitable for production of high quality oxide pellets. However, pyrrhotite is not removed from the magnetite matrix by either of' these simple beneficiation methods.

Jan 1, 1974

By Zohreh Kazemi Motlagh, Virginia T. McLemore

Critical minerals are nonfuel minerals, essential to the U.S. economy and national security, whose supply chain may be disrupted. Mine wastes are potential sources of critical minerals. The goal of this project is to estimate and characterize critical minerals endowment in three mining districts in New Mexico: Black Hawk (Grant County), Hillsboro (Sierra County), and Magdalena (Socorro County), and assess their acid-generating potential. The Black Hawk district is an arsenide five-element vein deposit (Ag, Ni, Co, As, U, Bi, and local minerals like Pb, Cu, Zn, W, and Sn). The Copper Flat mine in Hillsboro district is a copper porphyry deposit. The Kelly mine in Magdalena was first mined at 1878 and are carbonate-hosted Pb-Zn deposits. Mine waste rock piles and tailings are sampled using USGS Beta sampling procedure. Geochemistry results show that Black Hawk district mine wastes samples are elevated in Ag (>200 ppm), Co (290 ppm), Ni (2,130 ppm), and Zn (8,463 ppm). Copper Flat mine tailing is elevated in Bi (111 ppm), Cu (7,453 ppm), and Zn (2,360 ppm). Downhole profile plots in Copper Flat show the positive correlation between Cu, S and Te values. Magdalena samples are elevated in Cu (5,700 ppm), Zn (129,500 ppm), and Pb (58,100 ppm). Determination of acid-generating potential in these areas suggests that Black Hawk district mine wastes are non-acid-forming while high S present in some Copper Flat and Magdalena samples can potentially cause acid mine drainage.

Feb 1, 2025

By T. F. Tomb

Although the number of operating longwalls (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and have in some cases more than doubled. As a result of the increase in production, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Parameters in place to control dust were noted with special emphasis being placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control parameters in place at the time of the visit to dust concentrations measured at the tail, on the tail shearer operator and to the average concentration of dust determined from averaging all the measurements from the occupations sampled. The parameters in place to control dust were also compared to the gamut of technology known to be available to control dust. This paper presents a discussion on the effectiveness of the parameters in place to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1990

By K. Ohga, V. J. Hucka

The presence of methane gas in mines creates hazards of explosions, fire and suffocation. Under certain conditions the occurrence of methane also poses a danger of gas and coal outbursts. Consequently, prevention of gas and coal outbursts in coal mines requires a sound knowledge of methane gas occurrence in mine workings. However, the direct method of determining methane content of coals developed by the U.S. Bureau of Mines is time and labor consuming for measurement, a new transportable methane tester was developed for Japanese coal mines. The instrument automatically measures emission gas from coal samples in the underground and also records and stores the data. Back on the surface, the tester can be connected via a RS 232 port to a PC computer for methane content estimation. Details of this technique are described here. Results on methane content determined in Japanese and U.S. western coal seams are discussed, as well.

Jan 1, 1991

By K. V. Godfrey

With the increasing need to exercise better control over mill circuits has come a requirement to develop rapid, accurate means of measuring circuit parameters. One of the most important parameters is the assay of the material in the circuit (or about to be introduced to the circuit). To date, most on-stream analysis has been performed using X-ray fluorescence equipment. Neutron activation offers an alternative method in certain circumstances, and one which has several interesting advantages. Recognizing the need for a simple, safe neutron activation unit suitable for on-stream analysis in the mineral industries, Atomic Energy of Canada Limited has designed, built and tested the SHERLOCK system. One prototype (SHERLOCK I) is located in Ottawa and is now used primarily in research. A second prototype (SHERLOCK III) is located in Vancouver at the laboratories of B.C. Research. This unit is being used for some development research and for evaluating the unit in specific applications. Most of the work completed to date has been aimed at proving the technique and in developing some of the parameters needed to design systems for a milling plant. Funding for the work has been through research grants and through sponsor¬ship by interested companies.

Jan 1, 1971

By R. E. J. Putman

Rising demand, artificial market conditions, increased overseas competition, and a fluctuating international situation have brought ever increasing pressures to bear on the nonferrous metals industries, and particularly in the United States, Although capacity is being expanded by the construction of new plants and the development of new ore deposits, increasing attention is being focused on the possibilities of improving the performance of the existing installations and of getting the most out of the new equipment now installed. At first sight the task appears formidable. Based on raw materials which are nonhomogeneous, and possessing characteristics which are hard to quantify, even the processes by which the values in the ores are concentrated and extracted are in many cases not fully understood. The necessary analytical equipment and transducers demanded by these industries have also been slow in development and their earlier absence has hampered the application of modern control technology, This is reflected in plants which have been designed for ease of manual rather than automatic control, and in which the application of control techniques at first sight appears economically prohibitive. However, in any industry progress often comes only in small steps, It may be that by the wise choice of limited objectives and perhaps only partial solutions, substantial improvements in plant performance can be implemented now, and with only a modest investment. If modern control equipment is chosen of the type which can be reprogrammed, advantage can be taken later of more sophisticated solutions as the technology of the industry advances. This task of improving plant performance can and must be commenced even though our knowledge is incomplete. The experience of a related mineral consuming industry, with similar problems in the past, can be encouraging.

Jan 1, 1967

By C. E. Golson

Modern concrete technology emphasizes the basic qualities required of an acceptable aggregate: it must be clean, sound, homogeneous, and of a size gradation resulting in a concrete of the desired physical qualities at a minimum cost. In the case of coarse aggregates, crushing, scrubbing, and screening will usually provide the required material, although beneficiation is often necessary in order to eliminate unsound or deleterious fractions. Beneficiation is also applicable to fine aggregates,( but the processes most often employed are washing, classification, and dewatering.

Jan 1, 1959

By W. P. Arnott, P. Nascimento, X. L. Wang, K. C. Kocsis, S. J. Taylor, H. Firouzkouhi

We report the first spectral photoacoustic measurements of silica, coal, and kaolinite dust absorption coefficients from 11 to 13 μm at 5 nm resolution made with a tunable quantum cascade laser. This is important because airborne silica dust and coal dust within mining environments continue to be a problem for mine workers and staff due to their severe health effects on the respiratory system, while other dust types are potentially interferents to their detection. Our real-time spectra compare favorably with the non-real-time filter-based Fourier transform infrared spectrometer (FTIR) spectra obtained using the sampling system developed by NIOSH for their end-of-shift method to determine silica dust concentrations using a portable FTIR. We discuss our new dust generation system and instrument testing chamber. We also show that our PM4 silica mass concentration measurements by a low-cost air quality sensor (SPS30) are in good agreement with the TSI Aerosol Particle Sizer instrument, the NIOSH end of shift method, gravimetric mass, and correlate well with photoacoustic light absorption measurements at a wavelength where silica absorbs strongly.

Aug 20, 2022

By Circe Verba, Scott Montross, Jon Yang

This work is a first-order study to assess the suitability of an organic acid lixiviant to extract rare earth elements (REE) from coal preparation fines refuse sourced from a Pennsylvania mine with a total REE of ~ 300 ppm. The extraction of REE using an organic acid, in this case 0.1Mcitric acid and 0.5Mtrisodium citrate solution, is compared against 0.5M(NH4)2SO4, 1MHCl, 1.2MH2SO4, and 0.5Methylenediaminetetraacetic acid (EDTA). Ashing the coal waste material prior to leaching tests with the citrate solution nominally improved REE extraction. Buffered citrate solution recovered 7% of the total REE in the as-received Isabella Fines as compared to 11% in ashed samples, whereas (NH4)2SO4 extracted 5–6%, respectively. EDTA recovered up to 33%of the total REE, most likely due to the higher coordination chelate bond. Mineral acids, however, outperformed the organic acids on ashed material (16–52%REE recovery), suggesting that organic acids may not be a suitable competitive option for REE extraction from these types of feedstocks.

Jun 15, 2021

By P. J. Bethell

In the froth flotation process the detrimental effect of slimes on the froth flotability of valuable minerals has long been known.1 Work by Aplan2 on the froth flotation of coal has shown that the presence of clay slimes causes loss in flotation selectivity, and recovery of combustibles. Obviously then the presence of clay slimes to any great extent in the froth cell feed in a coal preparation plant is undesirable. This problem is exacerbated in plants treating raw 600 um (28#) by zero material due to the variation in flotation with size. The net effect of this phenomenon in a bank of cells treating raw minus 600 µm (28#) material s that by the time adequate flotation of the coarsest size fractions has occurred the finer sizes are already producing undesirable high ash material, which often leads to unacceptable overall quality. Reduction in aeration rate and/or chemical addition to combat this, further decreases the flotation rate of the coarsest fraction leading to heavy losses of coarse low ash coal to the tailings. The above mentioned characteristics formed a key aspect of the fine coal circuitry design at Elk Run Coal Company in Sylvester, WV. The plant was designed to produce compliance steam coal (less than 1.20 lbs. S02/million b.t.u.) Desliming ahead of the froth flotation was included, as the slimes in the plant feed were clay rich, had very high ash levels, and low potential recovery. Lab testwork had also shown that poor selectivity would be expected if raw minus 600 um (28#) material was froth floated.

Jan 1, 1986

By E. W. Sawyer

Attapulgite is a magnesium aluminosilicate clay mineral which exhibits unique, processing-enhanceable physical and chemical properties that are related to its current commercial uses. Properties of commercial interest are gelling, absorption, adsorption, binding, acid neutralization and many others. Major industrial applications are: (1) absorption by heat treated grades utilized in industrial oil and grease absorbents and in agricultural pesticide carriers; (2) gelling of aqueous liquid products by colloidal grades for stabilization and viscosity control in salt water drilling fluids, suspension fertilizers, liquid animal feed supplements, paints and tape joint compounds; (3) adsorption by heat treated varieties for the removal of catalysts, color bodies and other polar compounds from hydrocarbon streams; (4) gelling of organic liquids by colloidal attapulgite/surfactant blends in oil-type paints, fibrated and nonfibrated asphaltic coatings and mastic compositions, and (5) the binding of feeds and molecular sieve sorpents with colloidal type attapulgite products. These applications and other less common uses and potential uses will be discussed along with, the necessary selective mining and plant processing features related to each property and application.

Jan 1, 1986

By H. W. Hintze

Coal handling facilities, such as utility plants, coal terminals, ports, manufacturing, processing, etc. Protect themselves against interruptions in coal receipts by maintaining a 60 to 90 day supply in storage. Not too long ago, these storage piles were referred in terms of hundreds or thousands of tons. Today, it is not unusual to have hundreds of thousands or millions of tons in storage. Burn, or shipping and receiving, rates have increased dramatically and storage piles have grown in horizontal as well as vertical dimensions. Fixed systems for delivering and retrieving coal from storage have increased in length and operating capacity and have become highly sophisticated in their operation. With few exceptions, mobile material handling equipment is used to handle all coal beyond the reach of these systems. These machines take excess loose coal from the fixed system to the storage area, place it on the storage pile, compact it, maintain the pile, protect against spontaneous combustion, the spread of fires if they occur, and return the coal to the reclaim system as required, plus many of the small chores around the facility.

Jan 1, 1981

By R. D. Auten

This paper is primarily a report on the process of using oolitic aragonite, as received from Marconi& Ocean Industries, Ltd. without further processing, for a major portion of the raw feed to a rotary kiln producing cement clinker. Oolitic aragonite is a high purity calcium carbonate material, dust free, with the appearance of a course, white sand. It is farmed when under the right conditions of temperature ocean currents, and ocean floor topography. The calcium carbonate will precipitate into small spherical particles on the ocean floor. These oceanic conditions are correct to cause precipitation of the calcium carbonate near Ocean Cay in the Bahama Island chain. The present growing deposit near Ocean Cay is in the billions of tons and is mined by a relatively shallow-operation hydraulic dredge. The aragonite thus formed is en orthorhombic crystaline form of calcium carbonate with a specific gravity of approximately 2.9. At a temperature of 505°C. (940F), the aragonite converts to the hexagonal crystal of calcite with a specific gravity of 2.6 to 2.7. This change in specific gravity weakens the structure of the particles but the individual pieces are still fairly hard. When the material is then calcined at 900°C (1650°F), the particles retain their shape but become soft and will break up under finger pressure.

Jan 1, 1978

By J. P. McCluskey

The effects of air quality regulations passed in the last few years have been felt in a more pervasive way by the electric utility industry than by perhaps any other industry. I'm referring especially to those regulations dealing with the control of air emissions from stationary sources, and those specifying the quality of fuel used. Particularly, I would like to describe some of the effects that these regulations have had on the Commonwealth Edison Company. To put the subject into perspective, a brief descrip¬tion of the company will be presented first. Then, a historical outline of some of the efforts at control of electric generating station emissions will be described. Following this will be an indication of the Company's response to early State and local regulations prompted by the growing pressure for stringent envi¬ronmental control. Finally, the Company's plans to achieve com¬pliance with the most recent, Federally approved, State of Illinois regulations will be summarized.

Jan 1, 1973

By D. Weston

During recent years there has been a great deal of confusion in the North American mining industry with the introduction of new comminution terminology and claims (without substantiative evidence), for various types of equipment in this field. The authors will attempt to clarify the terminology used, and where possible, give illustrations of plant practice with actual operational and pilot plant data. This is considered necessary in order to obtain a clear picture of the comparison of such equipment to the revolutionary change that the Aerofall Mill has brought to the mining industry.

Jan 1, 1964

By Krawiec Alfons

The threat of rock bursts along with the danger from methane gas and coal dust explosions belongs to particularly dangerous phenomena in Polish pit-coal mines. This phenomenon results mainly from the physical-mechanical properties of the rock mass as well as the geological-tectonic structure of the Upper Silesian Coal Basin. In the postwar years in Polish coal mining thanks to a multi- directional activity, a decrease of rock bursts and their effects has been noted. For example, the number of rock bursts reported in 1965 amounted to 71 in comparison to only 23 in 1974. The ratio of rock bursts calculated for 100,000 tons of coal extracted from rock bursting strata amounted to 0.08 in 1965; however, in 1974 it amounted to 0.023 /Fig. 1/. These results were obtained in face of a continually growing potential threat from rock bursts caused by the systematic increase of extraction from rock bursting strata, exploitation at gradually greater depths along with the extension of exploitation into deposits enclosed in different types of pillars and other parts of deposits surrounded by workings. Despite the achievements of science and mining practice in this field, this threat has not yet been fully studied and controlled as it should be, As a result, research on preventing rock bursts is being continually widened in Poland. This research has a complex, multi-staged and long-range character. Theory, laboratory and field work in the mines are working on a solution to the problem.

Jan 1, 1976

By M. Schlegel, J. A. Villa Mena, R. E. Vivas

ArcelorMittal, headquartered in Luxembourg, is one of the world’s largest steel and mining companies. It supplies steel to industries such as automotive, construction, and energy, with a strong emphasis on sustainability and innovation. The company employs about 125,000 people and, in 2024, produced 42.4 million tons of iron ore and 57.9 million tons of crude steel across 15 countries. Its mining operations span Canada, the United States, Mexico, Brazil, Ukraine, Bosnia and Herzegovina, Kazakhstan, and Liberia, focusing on iron ore and coal extraction to support steel production. This study examines Peña Colorada, one of Mexico’s largest iron ore mines (a joint venture by ArcelorMittal and Ternium). Facing declining ore grades, Peña Colorada adopted Hexagon solutions to uncover and capture project value. A comparison of two Life of Mine (LOM) plans from 2012 and 2016 (before and after implementing Hexagon solutions) shows that between 2019 and 2023, Peña Colorada reduced actual waste by 26% (compared to 2012 LOM) and 19% (compared to 2016 LOM). LOM Plans are generated yearly, and each time, opportunities for reducing mining waste were identified, evaluated and implemented. The key driver was schedule optimization using Hexagon MinePlan Schedule Optimizer (MPSO). This reduction means less waste transported to disposal sites, resulting in fewer hauling equipment operating hours, lower fuel consumption, and reduced carbon emissions.

Feb 22, 2026

By Sahendra Ram, Ashok Kumar, Rakesh Kumar, AMIT KUMAR SINGH, Dheeraj Kumar, Arun Kumar Singh, Rajendra Singh

This article offers an examination of a retreat mining method conducted at the Pinoura Mine in India from 2010 to 2017. The method is atypical for coal mines of India’s coalfields. The method executes depillaring in a single pass and does not require the formation of galleries and support installation in splits, thus, reducing the cycle time. A variety of observations are discussed throughout this work and emphasis is placed on field measurements and depillaring under weak roof (RMR = 40–45). This paper discusses design techniques, specifically the estimation of the snook (remnant pillar) size, and important practical observations after the fact. The execution of this method was eventually conducted in eleven panels.

Aug 4, 2020