Search Documents

"With up to 2,300 m (7,545 ft) of rock on top of it, the Gotthard Base Tunnel, which is scheduled to go into regular operation in December 2016 in the Swiss Alps, is not only the world’s longest, but also the deepest railway tunnel ever built. Accordingly, the temperatures in the tunnel are very high, with the surrounding rock expected to reach 45° C (113° F) once the tunnel is fully operational. Since unrestricted rail operations are only permitted in temperatures of 40° C (104° F) or less, the heat has to be controlled with suitable equipment. Large fans developed and built especially for this application by TLT-Turbo GmbH provide fresh air for regular operations as well as during maintenance and repair work. Separate fans ensure that the emergency exits are properly ventilated in case of fire. In addition to coming up with a technical solution that could handle the special challenges of this project, the engineers and planners had to develop detailed preliminary plans as well as a sophisticated logistics and installation concept.The Gotthard Base Tunnel consists of two 57-km (35-mile) long tubes, one in each direction. Including all connecting and access tunnels, the entire underground system measures 152 km (95 miles). At Faido and Sedrun, at approximately 16 and 36 km (9 and 23 miles) respectively, two multifunction stations were built that cut each of the two tubes into three sections of roughly equal length. Here, trains can make emergency stops and change tracks, if necessary. This is also where eight large axial fans made by TLT were installed that exchange the air, i.e. they extract a certain amount of heated air and inject the same amount of cool fresh air a few hundred meters further down the train tracks. In addition to the four exhaust and four supply fans, 24 so-called jet fans were installed along with associated components like silencers, shut-off dampers, drives and lubrication systems from TLT.In addition to exchanging the air, these fans are used to enable maintenance and repair operations in the tunnel. Current plans call for blocking each tunnel tube for one night per week in order to perform preventive maintenance work, thus enhancing the tunnel’s overall functionality and availability. During these hours, many people will be in the tunnel who require fresh air. “One of the major criteria for winning this bid was the fans’ ability to quickly switch between a wide-range of modes. TLT fans are among the best in the world in this regard,” said Andreas Kuhn, TLT’s project manager for the Gotthard Base Tunnel, about the selection of his company’s fans for this project."

Dec 1, 2016

By Ezz El Din Abdel Hakim Khalaf, Khalid S. Essa, Marc Munschy, Mohamed A. S. Youssef

This study focused on joint interpretation of the aeromagnetic and radiometric data to allocate and describe the structural elements and mineralization zones such as uranium, gold, and sulfide in the Gebel Umm Tineidba and its surroundings, Eastern Desert, Egypt. The study region is covered by exposures of Precambrian rocks such as gneisses, migmatites, ophiolitic mélange, metavolcanics, younger granites, and Quaternary sedimentary covers. The application of the total intensity magnetic and reduced-to-pole maps, power spectrum, analytic signal, tilt-angle, and local wavenumber maps helps in recognizing magnetic sources distribution, lineament features, and mineral zones delineation. The obtained results indicate that the depths of the deeper NE–SW, NNE–SSW, and N–S trending structures extend from 400 to 1750 m and shallower ones range from 100 to 400 m. Finally, the main trends of these structures affect the probable mineralization zones.

Sep 22, 2022

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

By Surendra Kumar Biswal, Sachida Nanda Sahu, B. C. Meikap

The unutilized iron ore fines (IOF, − 10 mm, 45% to < 60% Fe(T)) left at various mine sites during blasting and processing are rich in goethetic-hematite associated with high clay and considered a potential iron ore resource. The variation of loss on ignition (LOI) from mines to mines is based on the goethite and clay mineral content. The clay containing below 45 μm is mostly brittle, causing beneficiation problems. The IOF has an LOI of 7.83%, with high silica (5.52%) and alumina (4.57%), and 57.17% of Fe(T) subjected to both conventional deep beneficiation (CDB) and magnetization roasting using high-ash non-coking coal to adopt the suitable upgradation process. The CDB and magnetization roasting concentrate has 62.61% and 67.58% Fe(T) with 64.69% and 85.19% yield, respectively. However, the presence of 6.40% LOI in CDB makes the ore challenging for pelletization. Characterization like X-ray diffraction(XRD), scanning electron microscope(SEM), and chemical analysis was used to assess the concentrate quality and potential industrial application.

Jun 4, 2022

By Ralf Plinninger, Pafos Busch, Richard Gradnik

This paper presents the details of the Bad Bergzabern tunnel project. This tunnel is the main part of the B427 federal road bypass, intended to improve the regional traffic infrastructure and to reduce the traffic load in the historic city centre of the health resort Bad Bergzabern. Located in the south-western part of Germany, the project area is situated at the eastern margin of the so-called Palatinate Forest, a low mountain region of mainly triassic sediments with a complex and variable geological history. The German federal government, represented by the office of mobility of Rhineland- Palatinate, awarded the contract to BeMo Tunnelling, a specialized Tunnelling company with a long history of innovation and success in NATM tunnelling. The contract includes the construction of two separate tubes with a length of approximately 1,44 km (0.9 mi)—the road (main) tunnel with a cross section of 101 m2 (1,090 sq ft) and a parallel rescue tunnel with a cross section of ca. 23 m2 (250 sq ft.) Both are connected by six cross passages. Tunnels and cross passages are excavated according to the principles of the New Austrian Tunnelling Method (NATM). Due to BeMo Tunnelling’s technical expertise and capabilities, the project team was able to engineer a speed-up concept that saves money and time for the construction team and client. This paper presents the innovative approach BeMo Tunnelling made to optimize the execution of the tunnelling works and the challenges the project team is facing with regard to a complicated geological situation, countermeasures against an increasing effect of climate change and volatile prices for construction materials.

Jun 13, 2023

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

Electromagnetic energy emitted from electronic devices has been known to interfere with other electronic systems, hindering their ability to function properly. Mines have many electronic devices critical to the health and safety of mine workers that could be negatively affected by electromagnetic interference (EMI). To ensure that devices are electromagnetically compatible, tests must first be conducted to measure emissions and check for immunity. There are many standards available across multiple industries that prescribe emission limits and test methods for electronic devices. Due to the unique environment of an underground mine, it may not be enough to simply adopt a standard from another industry to mining. A literature review has been conducted, and an overview of EMI standards in other industries will be provided in this paper. Also, an example of how a standard can be applied to mining equipment is presented. Finally, recommendations on standards which could potentially be applied to mining will also be included. This work will inform the mining industry of EMI standards in other industries so that mine workers and technology manufacturers have guidance of the steps that can be taken to investigate and reduce the impact of electromagnetic interference and potentially work toward electromagnetic compatibility. The findings and research involved in this effort can also be used to explore the need to develop mining-specific EMI recommendations and standards.

Nov 25, 2021

By G. Nash

Despite further declines in production for some producers, 1986 proved to be a landmark year for the asbestos industry. The key event was the adoption of The Asbestos Convention by the Inter- national Labour Organization (ILO) and its 150 member countries. The document, entitled "Safety in the Use of Asbestos", reaffirms the international consensus on the "controlled-use" approach to chrysotile asbestos regulation. The decision of the ILO has come at a critical point in time. It represents a major turning point and provides an important building block for the long term future of the asbestos industry.

Jan 1, 1987

By L. Alagha, M. Khodakarami

"This work focuses on the extraction of rare earth metals (REE) from aqueous solutions using stimuli-responsive polymers. Various parameters affecting the adsorption capacity of the polymer, including pH, polymer concentration and REE concentration were studied. The interfacial behavior of REE in aqueous phase before and after polymer addition and the mechanism of the formation of metal-polymer complexes and their properties were investigated using UV/VIS spectroscopy. Results obtained would help to test the feasibility of employing stimuli responsive polymers in pre-concentration of rare earth elements associated with other elements in mineral aqueous streams prior to solvent extraction. The pre-concentration step would reduce the amount of organic solvents used for extraction and striping compared to conventional extraction processes. INTRODUCTION Rare earth elements (REEs) have become the foundation for several technologies and have been used extensively in many industries such as modern electronics, green energy, health care and transportation and defense [1-4]. As these industry sectors are growing, the global consumption of REEs is going to increase dramatically. The current global REEs demand is estimated to be 105,000 tons of rare earth oxides per annum with an expected annual growth of 5.6% [5-6]. Rare earth elements are produced from different sources (primary and secondary). China is considered as the largest producer of REE in the world, providing about 90% of the world’s mine production while the United States is second with 4% of the mine production [7]. High global demand for rare earth materials results in shortage of such materials in the near future. It should be considered that the term ‘‘rare’’ earth is not an accurate term, since they are abundant in some extent in the Earth’s crust, but are typically finely dispersed. Thus, nowadays looking for more efficient and cheaper methods for extraction, separation and purification of low concentrated REE ores and exploring secondary sources are essential. Rare earth materials are found in raw condition and require treatment that involves several processes, which can consume money and time. Recent improvements in extraction and recycling technology have made the extraction of rare earth elements from rare earth sources more feasible in terms of cost and time [8-10]. Physical and pyrometallurgical methods require high-energy and thus high costs. Moreover, due to environmental problems, environmental protection systems are required, and they are not as adaptable as chemical processes [11, 12]."

Jan 1, 2016

By D. Pearson

About 15,000 tonnes of zinc per year is present in the dusts and fumes produced in electric arc and BOS steelmaking, secondary copper refining and brass ingot making. Apart from the use of some copper-smelter fumes for zinc chemicals manufacture, zinc is not recovered and their disposal by landfill entails some risk of pollution by leach-out. The paper describes processes for recovering the zinc based on leaching and electrowinning. It was shown that the procedures normally employed for purifying zinc-electrolytes derived from primary sources are sometimes ineffective for secondary materials. Alternative process routes are proposed. Source materials were leached with acidic or alkaline reagents and solvent extraction was employed for electrolyte purification in addition to the usual techniques involving precipitation. Examples of integrated flow sheets for specific source materials are presented.

Jan 1, 1980

By JOHN R. HEBERGER, MAHIYAR F. NASARWANJI, Jonisha P. Pollard, Lydia M. Kocher

nt in the mining industry, and identifying factors associated with these injuries is critical for developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53 percent) followed by bone fractures/chips (26 percent). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals — such as pipe, wire and guarding — and hand tools as the primary sources of hand and finger injury. Although the information on glove use was limited, leather gloves were most often worn when an injury occurred.

By Minerals and Materials Analysis Section

During 1996, US mines produced 319 t (10.26 million or) of gold metal valued at $4 billion. At yearend, mine reserves were estimated to be 4.7 kt (151 million oz) of gold metal. Almost all of the production was from western states. Nevada accounted for about 68% of national production. Information for this article was obtained through annual reports of mining companies, US Geological Survey (USGS) databases and other public sources. Table 1 shows production and reserves by mine. It divides the mines into two categories. These are producing mines whose primary product is gold, and producing mines for which gold is a byproduct or coproduct. The mines listed in Table 1 accounted for more than 98% of US gold production during 1996. Except the Daisy Mine, the table does not include mines that produced less than 31 kg/a (1,000 oz/year). The Daisy Mine started production in December of 1996. Nor does it contain mines whose byproduct concentrate is

Jan 1, 1997

By Donald C. Violetta

During 1963 more than 200 million tons of coal was consumed by the public utility industry. Ash residual, from the burning of this coal has caused disposal problems. In order to prevent air pollution, dust collection systems have been installed to suppress the fine ash emitted from boilers before it is discharged into the atmosphere. The collected ash, called fly ash, must be removed from the dust collection facilities and disposed in some manner, usually at a substantial cost to the utility. Many years ago fly ash disposal was not a serious problem because the demand for power was relatively low and coarse coal was burned on stoker type traveling grate machines. The low burning rates utilized on these grates did not produce large quantities of air-borne coal ash while the mechanics of this system of burning resulted in a clinkered residue of cinders. Both of these conditions resulted in the production of only small quantities of fly ash. As the demand for electricity increased, a method of burning pulverized coal was developed and was introduced to the public utility industry in 1918 at Milwaukee, Wisconsin.1 This method of firing was considered a significant advance in steam electric generation as it (1) permitted the use of coals that could not be economically fired by other methods and (2) has generally resulted in improved efficiency, greater generating capacity and lower costs.2 The utilization of larger generating units using pulverized coal substantially increased the quantity of fly ash which resulted in a&apos; more severe disposal problem.

Jan 1, 1966

By Lynn B. Hales

Unfortunately, the term "control" has a negative connotation in the minds of many of our operating plant personnel. Whereas the opposite is true of those associated with research and technical centers in our industry. The magnitude of this difference in opinion and actual experience has often proved to be a major factor influencing the success or failure of process control applications. Through the years, many plant people have endured a number of unsuccessful attempts by "outside" people to "optimize" their plants; and these experiences have proved to have had quite a callousing effect on them. On the other hand, in many plants, successful process control efforts have made firm allies of the operating personnel, and have increased the number of metallurgical people who are well qualified and experienced in process control. The instrumentation industry, computer industry, and the mining industry&apos;s ability to quantify what is really happening in our processes have grown and developed rapidly since the first control efforts were made in the 1930&apos;s (1). Because of this-,: new control opportunities are becoming increasingly more feasible and older well established ones are becoming even more practical and necessary with regard to the economic s of our industry.

Jan 1, 1979

By Kasimcan Koruk, Julian M. Ortiz

A geological model accounting for uncertainties possesses important advantages for resource estimation. Machine learning algorithms (MLAs) employed on multivariate geochemical datasets open up ways to new methodologies for such geological models with ease in comparison to traditional geostatistical methods. This article proposes a two-step MLA with an ensemble implementation to define geological domains and their uncertainties based on geochemical data. The proposed workflow is applied hierarchically on a dataset from a porphyry copper deposit to perform binary classification that can be attributed to alteration domains.

Mar 1, 2024

By ?. ?ivkovic

The silicate slag and copper matte that are the byproducts of smelting copper in a reverberatory furnace contain SiO2, FeO, Fe3O4, CaO and Al2O3, and Cu, Fe and S, respectively. These components influence the oxide (Cuox), sulfide (Cusul) and total (Cutotal) copper content lost in the waste slag. This paper uses multiple linear regression analysis (MLRA) to determine the degree of influence. The results of calculations obtained using MLRA were compared to actual measured results and found to have a large degree of correspondence, with the coefficient of determination R2 = 0.975. These results indicate that slag composition and copper content in the matte influence the copper losses in the waste slag with a probability of above 97%. It was determined that, of the total copper content of the slag, 74% is in sulfide and 26% in oxide form, and that this ratio is not dependent on the slag or matte composition.

Jan 1, 2010

By D. R. Tweeton

A modified push-pull field test and a computer model of cation exchange were developed to aid in evaluating cation exchange parameters prior to in situ mining. Reliable determination of these parameters is essential when modeling restoration of groundwater quality. The field test involves a much larger volume and much less disturbance to the ore sample than is feasible with laboratory measurements. This test can be performed in two or three weeks. It is relatively inexpensive, requiring one injection- production well and two or more wells for collecting samples of leach solution. The use of the model in interpreting test results is illustrated with field data from an in situ uranium mine. Much of the research was performed by the University of Texas at Austin, and was partially funded by the Bureau of Mines.

Jan 1, 1986

By Henning Schwarz, Ade Ogunsola, Anas Almousa

"The Riyadh Metro, commissioned by Arriyadh Development Authority “ADA” - the executive arm of The High Commission for the Development of Arriyadh -, forms part of a new public transport-system of Saudi Arabia’s fast growing capital city. The Design & Build project consists of 176 km of Metro Line with 57 km of tunnels. Beyond the Design and Construction, an additional aim of the ADA is to introduce up-to-date methodologies and improve safety in construction projects. A systematic dilapidation survey of buildings and infrastructures was a prerequisite for designing the required instrumentation and monitoring tools. Site investigations required of existing methodologies and the use of geophysical methods for achieving reliable results. Large diameter TBM tunneling is challenging in hot weather conditions and karstic ground. The present paper shows how modern technologies for underground construction are introduced into the local industry and gives an outlook on future projects in the Kingdom of Saudi Arabia. INTRODUCTION Riyadh, the capital city of the Kingdom of Saudi Arabia, is a fast growing city with more than 5.7 million inhabitants. The growth of the city is linked to the recent history of the Kingdom, where some initial milestones from the 1950’s can be highlighted: Revenue generation from the exportation of oil from the Kingdom; downstream investment of oil revenue in the reconstruction and development of the Kingdom; a general plan for the settlement of the Bedouins; the provision of a public electricity network for the city; the opening of the Riyadh - Dammam railway corridor providing a link from the capital to the Eastern Region; the commissioning of Riyadh airport (converted to Riyadh airbase, after the opening of King Khalid International Airport in 1983); and the relocation of ministries and other central government agencies in 1955. In 1974, The High Commission for the Development of Arriyadh was established as the organizational, planning, executive and coordinating body responsible for the development of Riyadh. Arriyadh Development Authority “ADA”, established in 1983 is the High Commission’s executive, technical and administrative arm. The ADA is responsible for implementing the High Commission's organizational, planning, executive and coordinating decisions and missions. The ADA’s president is a member of the High Commission (ADA 2015). One of the remits of the ADA is the preparation and execution of a transport plan for the city of Riyadh."

Jan 1, 2016

By Thomas E. Ban

During recent years fuel consuming industries of the United States have been caught between environmental restrictions and the uncertainty of obtaining an inexpensive fuel. With the advent of the National Energy Act of 1978 there has been added impetus to switch from gas and oil to coal. For industrial furnaces and boilers that were designed to bum coal, returning to an available compliance coal might be feasible. However, furnaces and boilers designed for gas or oil cannot reasonably be converted to coal unless the coal is initially gasified. All cases, nevertheless, depend upon the availability of an adequate structured coal of a compliance composition, a challenge to the coal mining industry. The foregoing problems have contributed to the current energy-coal crisis of today&apos;s economies. It therefore would be worthwhile to capitalize on previous experiences of the mineral processing industry.

Jan 1, 1979

By D. E. Nash

Environmental compliance programs for mining companies are not only important management tools, but can deflect serious civil and criminal penalties if violations of environmental laws do occur. The paper discusses the legal foundation for such programs and their basic structure.

Jan 1, 2001

By Tuanhui Wang, Qiwei Wang, Quanrui Liu, Jianhui Xu, Chao Wang, Yu Liu, Yuefeng Li

Rockburst is a highly destructive geological hazard that can cause casualties and equipment damage. To achieve highaccuracy discrimination of rockburst intensity, this article proposes an improved model that addresses the inefficient maximum membership principle used in traditional rockburst fuzzy evaluation models. The stress coefficient σθ/σc, brittleness coefficient σc/σt, and elastic deformation energy index Wet are selected as evaluation indicators for rockburst classification. Subjective and objective weights are obtained using the Delphi method and entropy weight method (EWM). Three types of membership function distribution forms are then used to obtain the membership degrees of each indicator to rockburst grades: trapezoidal membership function (TMF), normal membership function (NMF), and quadratic parabolic membership function (QPMF). Finally, six traditional models and six improved models are established using the maximum membership principle (MMP) and weighted average-maximum membership principle combination evaluation principle (WMP), respectively. Based on the analysis of 100 sets of rockburst field data, the accuracy, precision, recall, and F1-score of the improved evaluation model are increased by 11.3%, 0.097, 0.068, and 0.089, respectively, compared to the traditional model. The Delphi-NMF-WMP model is selected as the best model, with four performance indices reaching 97.0%, 0.979, 0.979, and 0.978. The best model is applied to evaluate the rockburst intensity of the Cangling Tunnel, Dongguashan Copper Mine, and Jiangbian Hydropower Station Diversion Tunnel, with evaluation results consistent with the actual situation, demonstrating the reliability and scientificity of the model.

Feb 28, 2024