Search Documents

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology (Le. stratification, turnover, and development of anoxic conditions with depth) of the lake. Limnologic data collected from four existing pit lakes indicate that pit lakes develop a thermocline, or temperature stratification, in the upper 10m to 30 m of the water column. Two of the pit lakes (26 m and 55 m deep) undergo seasonal turnover of the entire water column, whereas two deeper pit lakes (110 m and 240 m) undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column and a distinct chemocline develops with depth.

Jan 1, 1996

By Jose F. T. Agapito

The mining engineer must be able to predict the structural behavior of the rock around underground openings so that he can answer questions relating to safety and economics. With the present status of rock mechanics knowledge, exact predictions cannot be attained and approximate idealizations are made. As a first approximation, structural design makes use of theory, laboratory testing of rock properties, and available experience from excavations in similar rock formations. However, realistic design can usually be obtained only after in-situ observations and measurements are made. After all the information is collected, judgement and experience play a most important role in the final formulation of the design. This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator, The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale, The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver (Figure 1) . Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River Formation at a depth of 600 to 850 ft, Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek, The distance from the mine to the side of the mountain varies from 500 to 1,200 ft, and its height above the stream floor is approximately 700 ft.

Jan 1, 1974

By Peter Kreisman

This paper and four other papers on the MEQB Regional Copper-Nickel Study, presented today at the 1980 SME-AIME Fall Meeting are based on four years of extensive inter-disciplinary research and impact analysis supported largely by the Legislative Commission on Minnesota Resources. This study produced over 180 technical reports, the results of which are summarized in an Executive Summary available from the Minnesota State Planning Agency, St. Paul, Minnesota. Those wishing to examine the many scientific, engineering, environmental, social or economic issues addressed by the study are encouraged to obtain a copy of the executive summary. The executive summary includes a bibliography of all technical reports produced by the Regional Copper-Nickel Study and describes the five-volume, 26 chapter Regional Copper-Nickel Study Report.

Jan 1, 1980

By N. Magdalinovic

Generally speaking, erosion, as a process which entails degradation of surface layers of earth under the influence of the mechanical energy of surface waters, and from the point of view of biosphere sustainability, is a harmful process. This is absolutely true when agricultural and forest areas are concerned. However, if erosion is viewed selectively, this general definition about its harm raises serious questions. In other words, the erosion which takes place in the terrains where there is no vegetation because of the geological composition of the soil, does no harm. On the contrary, if the mineralogical composition of such terrains is characterized by a presence of precious and rare metals, erosion can be very useful. It contributes to the creation of new alluvial deposits of these metals in the waters in the plain land. It is here that torrents from hills come down and cause erosion. And finally, if there were no erosion, there would be no renewable deposits of gravel and sand.

Jan 1, 2007

By G. L. Mowrey

One critical element of the U.S. Bureau of Mines (Bureau) autonomous mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include vibration, passive infrared, radar, and natural gamma radiation (NGR). To establish which CID sensor technologies need to be developed for a given seam, coal and adjacent rock samples (i.e., immediate roof and floor) are being collected from selected major coal seams in the U.S. and are being analyzed in terms of NGR and other geophysical measurements. Results of the NGR measurements indicate that, in general, all shale and shale-like materials (e.g., drawslate, slate, and fireclay) have higher NGR readings than the coal seam. Consequently the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1990

By Huayang Luo, Hui Li, Wei Zhou, Gang Chen, Scott Huang

The beach and offshore gold resources demonstrated at Nome, Alaska are some of the richest found in Alaska. They contain potentially significant resources that may be exploited in the future. Several companies have contributed to the exploration and reserve estimation in Nome offshore gold deposits. More than 3,000 holes were drilled and over 10,000 offshore samples were analyzed in the Nome offshore areas of approximately 40 km2. Those 3,000 plus drill hole logs were converted into digital formats comparable with ArcGIS software. Considerable amounts of mineral resources data were processed and visualized using ArcGIS 8.3 and its geostatistic, 3D analysis, and spatial analysis components. In this study, based on the data processing and visualization results of ArcGIS, a user-friendly website for mineral resource management and utilization is developed using ArcIMS 4.0.1. ArcIMS is a GIS solution to build and deliver maps, data, and tools over the Internet. The Nome offshore mineral resources website presents the geostatistic and GIS analysis information. This site allows clients to access the information and perform ArcGIS analysis, such as interactive data query, and map layers display of the gold resource distribution, average grade, gold reserve, and relative mineral resource estimation via remote computers. With linkage to other related mining web sites, this web site allows users to search for related publications and more flexibly manage the information. A few other appropriate customized tools are also being developed to assist interactions between the server and clients for data analysis and management.

Jan 1, 2005

By William Gleason

The numbers tell the story of this one. More than 50,000 people and 1,890 exhibitors took over the Las Vegas Convention Center Sept. 24-26 for the largest mining trade show in the world ? MINExpo. Inside the convention center, some of the largest machines used in mining were on display. Caterpillar, Liebherr, Komatsu and Hitachi displayed ultraclass offroad mining trucks and shovels. Atlas Copco and Schramm were among companies that rolled in mining drills and Bridgestone, Goodyear and Michelin were among the companies showing off the massive tires used by the trucks. Throughout the three halls and an outdoor display area, just about every kind of product, gadget or service used in the mining industry could be found on display somewhere.

Jan 1, 2012

Satisfactory means of managing growth in boom towns is a concern in mineral, energy and other large industrial developments. This session will include examinations of socioeconomic impacts, major issues such as social disruption, case studies, methods of managing growth, and concerns involving Indian lands. Innovative methods will be offered to assist the public, government, and industry in finding solutions to managing growth in rapidly growing communities.

Jan 1, 1979

By Malte J. M. Gurgel, Axel Preusse

Recent three-dimensional surveying techniques have opened up new opportunities for the registration and monitoring of underground cavities. There are essentially two main methods available: Laser scanning, which is used both above surface and increasingly underground, and photogrammetry, which is also experiencing a renaissance with techniques like structure from motion through the algorithm-based orientation of high-resolution images. Both methods provide the capability to reconstruct reality by various 3-D products like points clouds and meshed models. However, they differ significantly in the steps of registration and calculation as well as in the resulting evaluation options.

By A. Rajoria

A dynamic process model for predicting the fluidized bed roasting of copper concentrates with high arsenic content is presented in this work. Mass and energy balances were performed based on roasting mechanism derived from thermodynamic data of species. The reaction rate data, obtained from pilot plant studies on major reactions, were used in tuning the kinetic parameters of the model. DEAS, a dynamic simulation package, is used in setting up the fluidized bed roaster plant model. The effect of process parameters such as concentrate feed rate, concentrate composition, airflow and cooling water rate on the temperature and conversion of roasting reactions are analyzed. The plant model captures the highly transient conditions occurring during the plant start-up, shutdown and other process perturbations. The application of this model in constructing a virtual plant environment for validating the operating procedures and operator training is presented.

Feb 23, 2014

By George H. K. Schenck

The North American-based mining engineer needs to understand the differences that exist between mechanical mining or boring machines built on this continent and those built in Europe. The differences Ere most clearly seen when machines for large-sized openings--about 15 feet high-are considered. This report will focus on the innovations of European origin. The rock-breaking tool, drag bit, or roller cone that is efficient for a particular project is related directly to the strength of the rock involved. This strength is generally stated in reference to the rock's unconfined compressivee strength in pounds per square inch (psi) although it is well recognized that a rock's shear strength is also important. Compressive strength has been adopted because it is simple to test for and provides a convenient comparison. Table 1 relates cutter type to compressive strength and indicates the general nature of the machine innovation devel¬oped in Europe.

Jan 1, 1970

By S. K. Pan, R. Venugopal, L. A. Kumaraswamidhas, Rakesh Prasad, Chandan Pandey

Cold compressive strength (CCS) and apparent porosity (AP) of pellets are essential properties regarding the burden of blast furnaces. The optimal required values for industries are 2.5 KN CCS and 21% AP. Blaine fineness and firing temperature are the decisive parameters analyzed here. During firing, microstructure phases such as silicate, hematite, and pore are formed. The phase’s grain density during induration influences the pellet’s CCS and AP. The influence of the factors over the response is evaluated by I-optimal (response surface methodology) design. Blaine fineness, firing temperature, pore phase grain density (PPGD), silicate phase grain density (SPGD), and hematite phase grain density (HPGD) affect the CCS and AP of pellets. The RSM-I-optimal predicted responses with a coefficient of determination (R2) of 0.89 for CCS and 0.91 for AP of iron ore pellets. Optimal conditions were Blaine no. = 1668 cm2/g, 1250 °C firing temperature, PPGD value 90 no/mm2, SPGD value 250 no/ mm2, and HPGD value 490 no/mm2, with 4.5 KN CCS 27%. The induration processes were investigated through statistical design of experiments for process optimization. Statistical analysis indicated the direct and interactive influence over CCS and AP. In this study, RSM-I-optimal modeling is used for iron ore pellets processing. The I-optimal prediction could be applied to make the process economical because information is obtained through fewer experiments.

Aug 18, 2020

By Liaqat Ali Shah, Muhammad Farooq, Zait Ullah Shah, Francisco Rolando Valenzuela-Díaz

Bentonite collected from Nowshera (Pakistan) was treated with NaCl, and the < 2-μm clay fractions were separated by sedimentation process. The textural changes in NaCl treated purified bentonite were compared with raw and physically purified sample. It was detected that the NaCl-treated purified bentonite and the sample purified by simple sedimentation, respectively, consist of sodium-montmorillonite and calcium-montmorillonite as a major clay mineral. The honeycombed-type morphology was observed for both the purified samples; however, the particles of NaCl treated purified bentonite were relatively in a compact form. The particle sizes of both the purified samples were found considerably smaller. The high volume percent of the fine particles was noticed in the NaCl-treated purified bentonite. This attributed that the sodium exchange has a valuable impact on the bentonite dispersion in aqueous media during particle size measurement. The relatively high mesopore area/volume and micropore area/volume and specific surface area (SSA) were detected in purified samples. The NaCl-treated purified sample showed relatively high mesopores area/volume than the sample obtained by simple sedimentation. These changes seem to be originated from either high montmorillonite contents and/or the smaller particle size, which might be produced after the layer rearrangement during the interlayer cation replacement by Na+ ions. The large SSA and high porosity of purified samples particularly the NaCl-treated bentonite suggest their potential use as adsorbents, catalysts, pharmaceuticals, and cosmetics.

Jan 7, 2021

By R. Duckett, D. Salisbury, R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance are reviewed.

Jan 1, 1999

By L. E. Eary, Andy Davis

The evolution of pit lake water quality depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock vs. oxidizable sulfide content, the alkalinity of recharging groundwater and the evapo-concentrative characteristics of the system. This paper assesses the geochemistry of 11 existing pit lakes, ranging from the acid Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits, with long-term chemistry lying on a geochemical continuum between end members that consist of influent calcium bicarbonate groundwater and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1998

By Malcolm Wills

Hedges Gold Pty. Ltd. mines and processes a lateritic gold orebody approximately 120 km south east of Perth in the Darling plateau. The operation is approximately 26 km from the town of Boddington and 31 km from the town of Dwellingup. Hedges operates under The Western Australian Environmental Protection Act, Licence Number 3183. Presently, nine Limitations and Conditions are applicable to the tailings dam. These conditions apply to maximum discharge/disposal quantity permitted. Hedges mine is located in state Forest within the eastern, low rainfall section of the Darling Range and within the waler catchment area of the Murray River. Ore is carted by 120 tonne haulpacks to the plant. The plant and tailings dam is on private farm land some six kms from the mine.

Jan 1, 1992

By Robin J. Hickson

The Ortiz Mine is operated by Gold Fields Mining Corporation, a subsidiary of Consolidated Gold Fields Ltd., one of the world&apos;s major gold producers. The Ortiz Mine is Gold Fields only heap leaching facility as well as being their first operating mine in the U.S.A. The hydrometallurgical processes utilized for recovery of gold and silver at Ortiz are discussed along with the several practical changes in operation adopted since start-up. Included are heap leaching by cyanidation, concentration of values on activated carbon, desorption, and the final electrowinning steps prior to shipment. Construction costs and pertinent technical data are shown.

Jan 1, 1981

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch type stirred mill. The experimental results were evaluated using stress intensity analysis. The performance was also compared in terms of mill orientation. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1*10−3 to 5*10−3 Nm at 750 and 1500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value. Additionally, to the best of the authors’ knowledge, this is the first study to compare mill orientation (vertical vs. horizontal) for the same mill and under the same test conditions.

Apr 21, 2021

By Justin Reed, Sara Bewley, Dwight M. Kinnes, Maryam Sadeghi, Ed Hart

This study compares wet gravity and dry magnetic separation for preconcentrating an allanite-rich rare earth ore from the Halleck Creek deposit. Material in the –300/+86 μm size range was treated to define a flowsheet that maximizes total rare earth oxide (TREO) recovery. The ore is dominated by feldspar and quartz, with hastingsite, an iron-bearing aluminosilicate. Because hastingsite’s density and magnetic response closely match allanite, it is difficult to reject using conventional methods. Two separation approaches were evaluated: MG12 spirals for gravity concentration and an Induced Roll Magnetic Separator (IRMS) for dry magnetic upgrading. MG12 spirals performed well in the rougher stage but provided limited gains when used as cleaners. When IRMS was applied as the cleaner stage, TREO grade and recovery improved substantially, showing that a dry magnetic cleaner circuit can effectively replace the wet gravity cleaner step. MG12 spirals remain suitable for highcapacity rougher duty, but dry magnetic separation delivers higher selectivity, simpler operation, and eliminates water use—offering a more efficient and sustainable preconcentration route in water-constrained environments.

Feb 22, 2026

By L. J. Buter, D. J. Collins

Introduction FMC&apos;s Paradise Peak gold mine was discovered by staff geologists in July 1983. Located south of Gabbs, in western Nevada, the deposit contains about 11 Mt (12 million st) of ore grading at 3.6 g/t (0.105 oz per st) of gold and 129 g/t (3.75 oz per st) silver. It is estimated that the ore contains 34 t (1.1 million oz) of recoverable gold and 933 t (30 million oz) of recoverable silver. The 3.6 kt/d (4000 stpd) mill began operation April 14, 1986, just 18 months after Davy McKee completed a feasibility study and construction, and two-and-a-months ahead of schedule. It also came in about 10% under budget at a cost of about $100 million. Crushing Run-of-mine ore is delivered from the mine in 45-t (50-st) haul trucks to a 272-kt (300,000-st) capacity open air stockpile. Ore is reclaimed using 5 m3 (7 cu yd) front-end loaders that feed a 91-t (100-st) hopper equipped with a 610- x 610-mm (24- x 24-in.) grizzly. A 1.4- x 11-m (54-in. x 35-ft) apron feeder delivers ore from the hopper by way of a vibrating grizzly screen with 127 mm (5 in.) openings to a 1- x 1.3-m (43- x 51-in.) Rexnord jaw crusher. Crushed material is conveyed to a 1.8- x 4-m (6- x 14-ft) Link Belt vibrating screen equipped with a 50-mm (2-in.) manganese grizzly bar deck. Screen oversize is fed to a 1.7/0.6-m (5.5 ft) Rexnord standard cone crusher. Product from this crusher joins the -50 mm (-2 in.) screen undersize and is conveyed to a 136-t (150-st) surge bin. Three hydraulically driven belt feeders deliver ore from the ore bin to three 2 x 6 m (7 x 20 ft) Link Belt single-deck tertiary screens fitted with 6 x 25 mm (0.25 x 1 in.) slotted polyethylene screens. Screen undersize - -6 mm (-0.25 in.) rock - is conveyed to a 3.6-kt (4000-st) ore storage bin. Screen oversize is delivered by way of a conveyor to a 91-t (100-st) surge bin. From this bin, two belt feeders feed ore to two 1.7 m (66 in.) Rexnord Gyradisc crushers, which are in closed circuit with the tertiary screens. Design features include magnetic protection for tramp iron removal and sloping floors and pump sumps for ease of clean up. Dust scrubbers keep the working environment clean and in compliance with state dust emission regulations. Grinding Two 1 x 4.5 m (3.5 x 15 ft) belt feeders deliver ore from the fine ore bin to a conveyor belt that feeds it to the 5 x 7 m (16 x 22 ft) Allis-Chalmers ball mill. The conveyor belt is equipped with a Merrick weightometer. This controls feed rate to the ball mill by speed control on the hydraulic motors driving the feeders. The 2.6 MW (3500 hp) powered mill grinds 3.6 kt/a (4000 stpd) to an average grind of 85% -75 µm (-200 mesh). The mill is in closed circuit with four 660 mm (26 in.) Krebs cyclones. Three of these are normally in operation while one is a standby. Warman pumps feed the cyclones through a cyclone distribution manifold. The cyclone underflow returns to the ball mill, which has a 300% average circulating load. Mill discharge pH is 11, and that is obtained through pebble lime addition to the feed belt. Cyclone overflow is sampled using a Heath & Sherwood two-stage sampler. It then flows to a 27-m-diam (90-ft-diam) Eimco thickener. Thickener overflow is returned to the grinding circuit, while underflow at 50% solids is pumped to the leaching circuit. Grinding-circuit design features include a steeply sloped floor for ease of clean up, an open area over the pumps for maintenance accessibility, and a ball hopper with a self discharge bottom to speed ball addition. Other features include a mill liner handler and an air clutch that connects the mill motor to the mill.

Jan 12, 1986