Search Documents

By R. Haldenwang, R. Erasmus, P. T. Slatter, R. P. Chhabra

Notches are used routinely for measuring the flow rate of water with free surface flows. As far as can be ascertained, no work has been done to investigate the performance of these flow rate measurement devices for non-Newtonian suspensions. The Flow Process Research Centre at the Cape Peninsula University of Technology has investigated the flow rate of kaolin and bentonite suspensions from a tank for two notch shapes, namely rectangular and triangular, and for 3 different concentrations of each suspension. The notches were calibrated using water and then the kaolin and bentonite suspensions were tested in them. The rheological characterisation of the fluids was done with a Paar Physica MC-1 rotary viscometer fitted with a cup and roughened bob. Analysis of the results shows a significant increase in discharge coefficient with increase in concentration, and the discharge coefficient has been correlated to the yield stress. This is the first such study, and further investigation is needed to confirm and extend these findings.

Jan 1, 2007

By S. Schmachtel

Several possible physico-chemical properties of composite electrodes for oxygen evolution are presented to describe experimental data for which a mathematical model had been developed. On this basis, local electrical and electrochemical properties of a composite electrode were investigated with conductive atomic force microscopy (CAFM) and scanning electrochemical microscopy (SECM). It could be shown by CAFM measurement that the boundary between matrix and catalyst particles seemed to have special advantageous electrical properties. The SECM measurements showed the presence of mass transport phenomena with increased surface concentrations, whilst the thickness of the Nernst diffusion layer was very small. An intermediate was detected and assigned to be hydrogen peroxide. From all species involved in the oxygen evolution reaction (H2O2, H+ and O2), it was concluded that local active spots exist on the electrode on which hydrogen peroxide reacts to oxygen and protons. A two?step two-material process was suggested to explain the whole oxygen evolution mechanism.

Jan 1, 2008

By M. Verri

The paper describes the design options available for the simultaneous production of liquid sulphur dioxide, via cryogenic condensation, and sulphuric acid in a sulphur-burning sulphuric acid plant. The impact of the operating conditions of the cryogenic condensation on plant capital and operating costs are discussed, with the main focus on the optimization of the most important economic and operative drivers of the non-ferrous mining industry, such as energy efficiency, reliability, and availability. A case history relevant to an integrated sulphurburning plant producing liquid sulphur dioxide and sulphuric acid, recently started up in the Democratic Republic of Congo, is described. Keywords sulphur burning, sulphuric acid, liquid SO2, cryogenic SO2 condensation, liquid sulphur dioxide, sulphur dioxide.

Aug 1, 2013

By A. Koning

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry?s experience base. The method of designing a refractory lined vessel is examined taking into account the impact of irreversible chemical swell, operating factors, design factors, and installation factors. The effect of geometry and incorporating additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional finite element analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed. Keywords refractory lining design,autoclave, finite element analysis.

Aug 1, 2013

The influence of Harold Hotelling?s work in the field of mineral economics is both unusual and outstanding. In the 66 years since its development, theory surrounding the economics of exhaustible resources has only been significantly researched since the early 1970s. At that time a wave of research into the economics of exhaustible resources arose from the threat of global resource scarcity and continued into the late 1990s. Current East Asian and global demand for natural resources as well as mineral and metal commodities, has stimulated interest in the optimal and sustainable exploitation of exhaustible resources to the point that the subject is worthy of review. Hotelling?s theory and the assumptions that he made in establishing a model for the optimal exploitation of mineral resources at the industry level and at the level of the individual mine owner, are examined. He showed that the rate of increase inexhaustible resource prices should be equivalent to the market rate of interest and that in a market with rising prices the rate of extraction should be constant. In markets where demand is stable optimal exploitation requires that the rate of extraction should decline over time, while in a monopoly market he showed that the rate of extraction is retarded. In addition, the effects of cumulative production on costs and prices, the uncertainty associated with estimates of the resource stock, the impact of exploration and issues of intergenerational equity are examined. An analysis of the optimal price path, extraction costs and mineral rents at an industry level is presented as a model. An analysis of the rates of production and optimal benefits at the individual mine level including total, average and marginal costs on the optimal rate of production, is considered. Optimal extraction rates for a mine with a clearly defined concave positive cost equation vary according to the position on the marginal cost curve. The influence of discount rates and the size of the ore reserves on the rates of mineral extraction are also examined and could define the frontier of usefulness for the ?economics of exhaustible resources?.

Jan 1, 2007

By George Kayesa

[ ] A multiple-bench slope failure occurred at Letlhakane mine on 14th July 2005. No injuries or damage to equipment was suffered and mining production was not affected. Slope failure was preceded by the precursors of tension crack formation, crack widening and extension as well as slope monitoring targets movement. It was predicted that slope failure was imminent using the Geomos slope monitoring system, though the timing was not certain. The area to be affected by the slope failure was also known before hand as was the slope failure mode. As a result, measures were taken to avoid exposing personnel and mining equipment to the slope failure risk. This paper discusses how the prediction of the slope failure of 14th July 2005 using the Geomos slope monitoring system resulted into avoiding potentially fatal injury, damage to mining equipment and loss of mining production.

Jan 1, 2006

Many industries base their decisions on the assaying of tiny analytical sub-samples. The problem is that most of the time several sampling and sub-sampling stages are required before the laboratory provides its ultimate assays using advanced chemical and physical methods of analysis. As long as each sampling and sub-sampling stage is the object of due diligence using the Theory of Sampling it is likely that the integrity of the sought after information has not been altered and the generated database is still capable to fulfil its informative mission. Unfortunately, more often than not, unawareness of the basic properties of heterogeneous materials combined with the unawareness of stringent requirements listed in the theory of sampling, lead to the conclusion that massive discrepancies may be observed between the expensive outcome of a long chain of sampling and analytical custody, and reality. There are no areas that are more vulnerable to such misfortune than sampling and assaying for trace amounts of constituents of interest in the environment, in high purity materials, in precious metals exploration, food chain, chemicals and pharmaceutical products. Without the preventive suggestions of the theory of sampling serious difficulties may arise when making Gaussian approximations or even log-normal manipulations in the subsequent interpretations. A complementary understanding of Poisson processes injected in the theory of sampling may greatly help the practitioner understand structural sampling problems and prevent unfortunate mistakes from being repeated over and over until a crisis is reached. This paper presents an overview of the theoretical, practical and economic difficulties often vastly underestimated in the search for quantifying trace amounts of valuable or unwelcome components.

Jan 1, 2009

By S. A. Ziebold

There is often a need to increase capacity through existing mist eliminator installations without significant tower modifications. Often there is not enough extra space outside existing vessels unless more expensive changes can be justified. Also, plant downtime must be considered. The challenge in retrofitting is to overcome velocity limitations inherent in the design while at the same time extend performance capability. The solution most often is to create new ways to add extra filter area while remaining constrained to the existing space. This strategy, however, can dangerously backfire if basic design principles are not followed. Mist eliminator design is a complex integration of many conflicting performance parameters. Often the objective is to increase scrubbing capacity while maximizing collection efficiency and service life and minimizing operating pressure drop (energy cost), particle regeneration (re-entrainment) and overall maintenance costs. Results of plant retrofitting using mesh pads, impaction fibre beds and diffusion fibre beds are presented based on actual plant projects. Often the retrofit project can be more effective by increasing the scope and combining other new plant equipment with the upgrade such as new tower components. In some cases, the type of mist eliminators can be upgraded from impaction type (velocity dependent) to Brownian diffusion type (velocity independent) if additional downstream protection or reduced emissions are desirable, especially at turndown rates. Trade-offs between different fibre bed types and styles are discussed as they relate to performance and maintenance.

Jan 1, 2007

By FJ Fourie

Lack of success in attempts to develop viable large-scale continuous mining techniques (previously reported by MP o?Hare in 2004) led the team at Kopanang to explore alternative solutions to their ongoing need for improved profitability. By calling into question the basic assumptions around the stoping of narrow tabular deposits of gold, fragmentation and more particularly, the range of sizes of blasted rocks eventually became the focus of serious study. This background is briefly covered before the sequence of the investigations is described. So far, some of the ?rules of thumb? derived over the years have been confirmed, albeit for totally different reasons than those from which they arose; some persistent theories on gold loss have been debunked, and some new ones have been developed. Blast optimisation (the means by which desired fragmentation is achieved) has been based on tailoring energy to rock characteristics in an innovative packaging design for explosive charges. Other beneficial consequences arising from the work include increased production volume and gold output, a decrease in milling consumables, and the Mine Call Factor is being maintained at a level previously thought to be unachievable. This is very much a ?work in progress?, and it is empirical in its approach. The authors are the first to recognise that they have yet to determine in absolute measures why some of the innovations have had the effect that has been observed. Also that there other factors which may contribute to the result, but which have not yet been examined. Nevertheless, publication of the work completed so far is felt to be justified; firstly on the basis of the achievements themselves, and secondly for the benefit of others in the industry for whom similar problems exist. Statistical reports of the effects on the business are included at the end of the report. Detailed laboratory test results have been separated into an appendix, leaving salient graph and tabulated data in the main text. For ease of reading, units of measurement for particle sizes below 1mm are described in microns, but millimetres have been retained for those at that size or greater.

Jan 1, 2007

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By F. A. G. M. Camisani-Calzolari

Approximately 850 groundwater samples were collected over a 29 300 km2 region of the semi-arid Northwestern Cape during the site selection phase of the South African radioactive waste disposal project. The purpose of the geostatistical investigation was primarily to delineate metallogenic occurrences and provinces which might exist below the thin veneer of surficial material and could thus interfere with the suitability of the site, and to quantify the distribution patterns of groundwater parameters in order to establish a relationship to local and regional geology. Up to 34 variables were analysed for each sample. Structural analysis revealed that the study area is statistically uniform. The variables have low correlation coefficients, with the exception of major ions, indicating a general poor degree of interrelationship between the spatial distribution patterns of the different variables. On the other hand, the long semivariogram range of the majority of variables, which reaches 70 km in cases, demonstrates their continuity on a regional scale. Kriging, which was repeated for each parameter, reveals that most variables, particularly trace metals, have distribution trends which are not influenced by local geomorphology or surface lithology. A 50 km wide, 220 km long metallogenic province, defined by kriging, could possibly reflect a broad metallogenic imprint on the basement and could represent a target area for prospecting. Kriging also reveals the possible existence of a wrench faulting system which may well have influenced the Namaqualand coastal graben and the western boundary of the Karoo.

Jan 1, 1987

By K. Sasaki, Y. Oriia, Shigeto Kuroiwa, H. Miki, Yuji Aoki, T. Hirajima, G. P. W. Suyantara

The effect of a sulfite reagent on the floatability of chalcopyrite and enargite was investigated in this paper. The flotation tests using single and mixed minerals were performed under various concentrations of sulfite. The flotation tests using a single mineral showed that the sulfite reagent depressed the natural floatability of both minerals at pH 9. Surprisingly, enargite was floated after the addition of potassium amyl xanthate (PAX) following the sulfite treatment, and the floatability of chalcopyrite depressed under a similar condition. X-ray photoelectron spectroscopy analysis results showed that the sulfate species increased after the sulfite treatment on both minerals. However, the addition of PAX removed this sulfate species and rendered the enargite surface hydrophobic. This phenomenon was not observed on the chalcopyrite surface. FTIR analysis and PAX adsorption studies were performed to support this finding. The flotation of a mixed mineral was in agreement with the flotation of a single mineral, indicating a possibility for selective flotation of chalcopyrite and enargite using the proposed method. Keywords: Flotation, chalcopyrite, enargite, sulfite, potassium amyl xanthate

Jan 1, 2020

By C. M. Rule

High pressure grinding rolls (HPGR) technology has come a long way in its application for comminution duty in hard rock mineral processing in the last three years. Several major projects in copper, nickel, gold, molybdenum, platinum, and iron ore have opted for this technology. Advances in wear abatement technology have established the HPGR as a reliable machine with the required high utilization and availability. The HPGR captures the imagination as the next step change improvement in ore processing, based on the following benefits: ?Energy efficiency (potentially 10?30% more efficient)?very topical in an increasingly ?green? society, and in times of rapidly increasing energy costs and availability concerns. 2008 has shown this to be especially important in Southern Africa ?High (and stable) throughput with a relatively small footprint ?Lower operation cost ?Liberation benefits ?Creative ?mine-to-metal? system improvements made possible by HPGR. The platinum industry, renowned for its historically conservative approach, has not been left behind with two significant new HPGR installations, one in Platreef application and one in UG2 application, commissioned in 2008. While the decision for the Platreef application was driven primarily by comminution circuit capacity and design imperatives, the UG2 application seeks to develop a flowsheet that will have a significant recovery benefit in addition to capacity increase and reduced operating cost. The Platreef application of HPGR also provides the opportunity to introduce a novel comminution flowsheet and to demonstrate exceptionally low wear rates treating very hard, abrasive and variable ore types. The HPGR lends itself for inclusion in existing SABC circuits to increase the capacity of the plant and mills. With current PGM prices many operations are attracted to the HPGR technology benefits. The HPGR clearly has the potential to transform entrenched opinion and provide decision makers with significant alternative comminution options. This paper aims to provide an overview of the current applications and to speculate on the transforming stimulus that the HPGR exerts on industry.

Jan 1, 2009

By D. Vogt

"Rock has been cut in the process of mining since before the invention of explosives. Today, we seek to return to cutting to reap the benefits of continuous operations for South African underground hard-rock mines, to improve speed of access to the orebody, and to improve the efficiency of mining operations.Development of new technology fits within a framework of engineering knowledge. By understanding the characteristics of the rock, the tools we use to cut it with, and the history of mining and rock cutting, we can see the genesis of the road-header, the longwall, and the continuous miner, all drag bit cutters. They have emerged as the solutions of choice for underground mining of softer materials such as coal and potash. In hard rock, the challenges are the forces required to break the rock, and the wear of the tools caused by the rock’s abrasiveness. Only disc cutters currently handle the challenges, and even then, often not economically. New materials like thermally stable diamond composite will help, as will combinations of mechanical cutters and other methods such as high-pressure water or high temperatures.It is not clear what will emerge as the consensus technique for hardrock cutting. Experience teaches that development is expensive and the market is small. Will mining companies partner with equipment developers to make the technological leap? Or will the solution come from a systems approach, not considered here?IntroductionBlasting is the dominant method of breaking rock for the purposes of mining. When used underground, blasting is part of a batch process. If rock can be cut rather than blasted, mining can become continuous, leading to process and efficiency improvements.Coal produced from underground mines is now predominantly excavated using mechanical means, but underground hard rock is still broken primarily by explosives.This paper traces the history of rock cutting, reviews the main physical processes that are or could be used, and comments on the future. It is written from the perspective of narrow-stope hard-rock mining typical of South African gold and platinum mines."

Jan 1, 2016

By T. Nyakudarika

The Unki Platinum Mines concentrator, employing an MF2 circuit configuration which includes fully-autogenous primary milling of run-of-mine (ROM) ore, was commissioned in November 2010. The project was Anglo American Platinum?s first PGM concentrator in Zimbabwe and would form a significant contribution to the group?s platinum production. The project financials demonstrated that the project was operating-cost sensitive. After reviewing the metallurgical testwork, mineralogical examinations, and the history of similar operations, it became apparent that the Unki ore characteristics rendered it amenable to autogenous milling. The primary ball mill, structurally designed for 30 per cent steel load, could be operated at the required initial phase throughput with fully-autogenous primary milling, realizing savings in both power requirements and grinding media consumption. The original mill sizing had been done with fully-autogenous milling in mind, but allowing for flexibility and mitigation in case of varied mining fragmentation. Since attaining steady state, target grinds have been achieved. This paper looks at the Unki ore characterization programme, design considerations, and the operational and control philosophy for a successful comminution circuit, and discusses the design to produce a flexible, low opex, mitigated comminution and overall MF2 flowsheet that is easily expanded in line with the potential for optimum exploitation of the orebody.

Jan 1, 2012

By W. K. Osae

A value assessment model which uses deal objectives, financial and non-financial indicators as a guide to assess value creation in mergers and acquisitions. The extent to which post- merger deal objectives are achieved and the potential benefits derived from mining deals that may not necessarily be financial of nature, but which are necessary to sustain and enhance future performance, were considered. The pre-merger and post-merger performances based on some financial indicators that reflect profitability for shareholders were also used. This value assessment model was used to assess four major deals that have occurred in the South African mining industry since 2003 as part of a postgraduate dissertation. In this paper, the Harmony and ARMgold merger is used as an example of how the model can be applied. The model?s relevance and applicability can also serve as a guideline in developing a framework or holistic guideline in assessing whether mining BEE deals in South Africa create value.

Jan 1, 2011

By B. Emwanu, R. A. Raju

The implementation of new technology in mining can be likened to a paradoxical situation or dilemma, where, on one hand, major mining projects are not able to solicit investor funding unless it is proven that the business cases were developed using tried and tested mining methods. On the other hand, new and innovative mining technology and mining methods need first to demonstrate and prove themselves under real production conditions over a reasonable period before they can be considered bankable feasibility studies in the mining industry. This dilemma locks new mining technology investments in a continuous cycle of underinvestment. Technological innovations are particularly relevant to the mining industry, which deals with the challenges of depleting access to resources, requiring new solutions to remain sustainable and competitive. In the last decade, the mining industry has come to realise that technological innovations can directly contribute to its sustained competitive advantage (Sanchez, Hartlieb, 2020), helping to reduce costs, lessen environmental impact, increase production, and improve mineral recovery. While understanding barriers and drivers for technology adoption is important for the success of technology implementation efforts and the sustainability of the mining sector (Muduli et al., 2013), this paper suggests strategies to exit the dilemma, proposing a preliminary framework.

Oct 24, 2025

By C. Birch, M. Katuruza

"The purpose of this study was to demonstrate unmanned aircraft system (UAS) technology in opencast highwall mapping using the experience at Isibonelo Colliery in Mpumalanga Province of South Africa. In opencast mines, geological mapping has evolved over time and there have been challenges in extracting valuable information from exposed highwalls due to restricted access for safety reasons. A UAS was used at Isibonelo Colliery to conduct highwall mapping, using drone-based digital photogrammetry techniques. A demonstration survey was undertaken during February 2018. The highwall flyover demonstration was planned for two areas (North and South pits) where field control points were placed by the mine survey department. A contractor used a DJI Phantom 4 (Pro) for the highwall mapping. Raw data was processed within 48 hours and a 3D model of the mapped pit area was produced. Further data extraction included obtaining updated weathering and lithological contact elevations and thicknesses for use in short-term planning. The results showed a good correlation between the resource model and the UAS data model. The project was considered a success and highwall flyover mapping and is now standard practice at Isibonelo Colliery.IntroductionDetailed geological mapping is crucial to the understanding of the structure of any mineral deposit. Several mapping methods may be applied depending on the available exposure/outcrop and nature of the orebody; for example, coal deposits typically suboutcrop only, therefore an opencut highwall provides the best exposure for mapping the geology. Mapped information, when incorporated into a resource model (generated from exploration borehole data), improves the understanding of the orebody or coal seam. This research paper focused on the use of unmanned aircraft system (UAS) technology for pit highwall mapping to generate data for updating geological models and avail the latest information to mine planning to improve the short-term plans."

Mar 1, 2019

By L. A. Cisternas, A. Lopez-Valdivieso, Y. L. Botero, L. Cortes

In the processing of sulfidic ores, pyrite is usually depressed and ends up in the tailings. However, pyrite is the most common species responsible for acid mine drainage (AMD) due to its spontaneous oxidation. This AMD affects the tailing chemical stability by dissolving some toxic or heavy metals species such as As, Cd, Co, Pb, and Zn, which can migrate into the surrounding ecosystems. Therefore, the strategies to reduce pyrite’s environmental impacts are a crucial point to produce more chemically stable tailings. Consequently, numerous studies have been made to find procedures that could inhibit or restrain AMD. This work aims to develop a procedure for designing conceptual flotation circuits that can produce tailings with low content of pyrite and to assess this type of circuit with traditional flotation circuits. The method consists of applying optimal flotation design where three products are considered: metal concentrate, pyrite concentrate, and tailing with low content of pyrite. Two approaches are considered; in the first, a flotation circuit is designed to generate a concentrate rich in all sulfide minerals and to obtain a tail with low pyrite content. Then, a second flotation circuit is designed for the selective separation of the bulk into metal concentrate and pyrite concentrate. This is called fractional separation design. In the second approach, a flotation circuit design is realised that generate the three products simultaneously. This is called integrated separation design. Both fractional separation design and integrated separation design are assessed in this paper. This methodology is focused on cleaner production (waste prevention and resource minimisation) rather than end-of-pipe technology (treat existing waste). The methodology was applied to a copper sulfide ore from a local company in the Antofagasta region (Chile). This ore contains chalcocite, covellite, iron oxides, and pyrite. Keywords: Flotation, tailing, pyrite, cleaner production

Jan 1, 2020

By A. P. I. Popoola

Aluminium AA1200 was laser alloyed with a combination of nickel and titanium diboride using different weight ratios. Chemical reactions took place with the formation of different phases. The characterization of the alloyed surfaces was carried out by x-ray diffraction (XRD), optical and scanning electron microscopes. The alloyed surfaces are composed of the initial phase of Al-Ni dendrites and eutectics of TiB2/Al and TiB2/Ni distributed on the initial phase. Experimental results obtained showed that Al-Ni intermetallics brought about a significant increase in the hardness property of Al; however, these intermetallics are highly brittle and prone to fail by brittle fracture or stress corrosion cracking when put in service. The addition of TiB2 brought about a reduction in the formation of the seintermetallic phases. A microhardness increase of over 10 times the hardness of the substrate was achieved. Keywords Dendrites, intermetallics, metal composite, Nd: YAG laser.

Jan 1, 2011